[Federal Register: September 23, 2003 (Volume 68, Number 184)]
[Rules and Regulations]
[Page 55193-55196]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr23se03-2]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. 2003-NM-137-AD; Amendment 39-13304; AD 2003-19-02]
RIN 2120-AA64
Airworthiness Directives; Boeing Model 777 Series Airplanes
AGENCY: Federal Aviation Administration, DOT.
ACTION: Final rule; request for comments.
-----------------------------------------------------------------------
SUMMARY: This amendment adopts a new airworthiness directive (AD) that
is applicable to certain Boeing Model 777 series airplanes. This action
requires inspections of the outboard leading edge slats on the wings
for installation of seal assemblies with undersized seal inserts and
missing or gapped inserts, and follow-on and corrective actions if
necessary. This action also provides for an optional replacement of the
seal assembly in lieu of the inspections. This action is necessary to
find and fix such discrepancies, which could result in cracking of the
slats, subsequent separation of the cove skin, structural damage or
loss of the trailing edge wedge, and consequent reduced controllability
of the airplane. This action is intended to address the identified
unsafe condition.
DATES: Effective October 8, 2003.
The incorporation by reference of certain publications listed in
the regulations is approved by the Director of the Federal Register as
of October 8, 2003.
Comments for inclusion in the Rules Docket must be received on or
before November 24, 2003.
ADDRESSES: Submit comments in triplicate to the Federal Aviation
Administration (FAA), Transport Airplane Directorate, ANM-114,
Attention: Rules Docket No. 2003-NM-137-AD, 1601 Lind Avenue, SW.,
Renton, Washington 98055-4056. Comments may be inspected at this
location between 9 a.m. and 3 p.m., Monday through Friday, except
Federal holidays. Comments may be submitted via fax to (425) 227-1232.
Comments may also be sent via the Internet using the following address:
9-anm-iarcomment@faa.gov. Comments sent via fax or the Internet must
contain ``Docket No. 2003-NM-137-AD'' in the subject line and need not
be submitted in triplicate. Comments sent via the Internet as attached
electronic files must be formatted in Microsoft Word 97 or 2000 or
ASCII text.
The service information referenced in this AD may be obtained from
Boeing Commercial Airplane Group, P.O. Box 3707, Seattle, Washington
98124-2207. This information may be examined at the FAA, Transport
Airplane Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at
the Office of the Federal Register, 800 North Capitol Street, NW.,
suite 700, Washington, DC.
FOR FURTHER INFORMATION CONTACT: Gary Oltman, Aerospace Engineer,
Airframe Branch, ANM-120S, FAA, Seattle Aircraft Certification Office,
1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425)
917-6443; fax (425) 917-6590.
SUPPLEMENTARY INFORMATION:
Related AD
This AD is related to AD 2002-11-06, amendment 39-12767 (67 FR
38587, June 5, 2002), applicable to certain Boeing Model 777 series
airplanes. Boeing Alert Service Bulletin 777-57A0034, Revision 2, dated
November 19, 1998; Revision 3, dated May 4, 2000; Revision 4, dated
July 20, 2000; and Revision 5, dated January 25, 2001; were referenced
as the appropriate sources of service information for accomplishment of
the required actions. That AD supersedes AD 2000-19-08, amendment 39-
11909 (65 FR 57282, September 22, 2000), to continue to require
repetitive detailed visual inspections to detect cracking of the
coveskin on the outboard leading edge slats, and corrective actions, if
necessary. AD 2002-11-06 also continues to provide for an optional
modification that significantly increases the repetitive inspection
interval, and expands the applicability of AD 2000-19-08 by mandating
the currently required inspections, and corrective actions, if
necessary, for additional airplanes. Also, for airplanes on which the
optional modification has been accomplished, AD 2002-11-06 requires a
new one-time inspection for undersized (incorrect diameter) seal
inserts installed in the spanwise bulb seals on certain slats, and
replacement of seal assemblies with new assemblies if necessary.
Since the Issuance of That AD
Since the issuance of AD 2002-11-06, the FAA has received
information from the manufacturer indicating that Group 4 airplanes may
have seal assemblies on the outboard leading edge slats on the wings
that were installed during production with undersized (incorrect
diameter) inserts. In addition, those inserts may have receded into the
ends of the seal assemblies.
We also have received reports of the installation of seal
assemblies with missing and gapped inserts. These seal assemblies are
installed on Model 777 series airplanes on which the seal insert
installation was done per Revision 3, 4, 5, or 6 of the referenced
service bulletin, and on which the seal inserts were installed during
production. Investigation revealed that, during installation, the
inserts were stretched and did not return to the original shape before
being trimmed and bonded into place. Subsequently, the insert recedes
into the ends of the seal assembly, and can become unbonded and detach
from the seal assembly. Additionally, when the seal is stretched during
installation, the insert can separate at a location along its length
which allows the seal to recede from the center of the seal assembly.
Such conditions, if not found and fixed, could result in cracking of
the slats, subsequent separation of the cove skin, structural damage or
loss of the trailing edge wedge, and consequent reduced controllability
of the airplane.
Explanation of Relevant Service Information
We have reviewed and approved Boeing Alert Service Bulletin 777-
57A0034, Revision 7, dated May 22, 2003, which describes procedures for
inspections of the outboard leading edge slats on the wings for
installation of seal assemblies with undersized (incorrect diameter)
seal inserts and missing or gapped inserts, and follow-on and
corrective actions if necessary. The applicable inspections and follow-
on and corrective actions are specified in Part 5 and Part 6 of the
Work Instructions of the service bulletin, described below:
Part 5--Seal Insert Diameter Inspection and Seal Replacement:
Describes procedures for airplanes on which the seal insert
installation has been done per Part 4 of the service bulletin. (Part 5
was added to Revision 6 of the referenced service bulletin for Groups 1
and 2 airplanes that had done Part 4 of the service bulletin referenced
[[Page 55194]]
in the existing AD.) The procedures specify a one-time inspection of
the seal assemblies for correct diameter seal inserts on slat numbers
4, 5, 10, and 11; if the correct diameter insert was installed and the
insert has receded into the ends of the seal assembly, install an
insert segment into the ends of the seal assembly; if incorrect
diameter seal inserts are installed or the inspection was inconclusive,
replace the seal assembly with a new seal assembly. If the correct
diameter insert is installed and the insert has not receded into the
ends of the seal assembly, no further action is specified for Part 5.
Part 6--Seal Insert Gap Inspection and Seal Assembly Replacement:
Describes procedures for all airplanes on which the seal insert
installation has been done. The procedures specify a one-time
inspection of the seal assemblies for missing or gapped inserts.
If the assembly insert is not missing and no gaps are found, the
procedures in the service bulletin recommend eventual replacement of
the seal assembly with a new seal assembly as specified in Figure 8 of
the service bulletin at the time specified in Figure 1 of the service
bulletin, regardless of apparent condition.
If the seal assembly insert is missing or gaps are found, the
procedures specify doing the following:
For airplanes on which the installation specified in Part 4 has
been done: Do a cove skin inspection for cracking as specified in Part
1 of the service bulletin. If no cracking is found, repeat the
inspection at the intervals specified. If any cracking is found, the
procedures in the service bulletin specify the applicable actions as
specified below:
[sbull] For any crack that is 1.5 inches in length or less, the
follow-on actions include stop-drilling the cracking, doing an internal
inspection for cracking as specified in Part 2 of the service bulletin,
repairing any cracking found, doing a slat adjustment check, and
repeating the cove skin and internal inspections at the intervals
specified.
[sbull] For any crack that is more than 1.5 inches in length, the
follow-on actions include doing an internal inspection for cracking as
specified in Part 2 of the service bulletin, repairing any cracking
found, doing a slat adjustment check, and repeating the cove skin and
internal inspections at the intervals specified.
[sbull] As an alternative for all cracks: Replace the slat and do a
slat adjustment check, then repeat the cove skin and internal
inspections at the intervals specified.
If any cracking exceeds certain limits specified in the 777
Structural Repair Manual, or if internal cracking is found, the service
bulletin specifies contacting the manufacturer for repair instructions.
For airplanes on which the seal insert installation was done during
production, the procedures also include eventual replacement of the
seal assembly with a new seal assembly as specified in Figure 8 of the
service bulletin, at the time specified in Figure 1 of the service
bulletin, regardless of apparent condition.
Accomplishment of the actions specified in the service bulletin is
intended to adequately address the identified unsafe condition.
Explanation of the Requirements of the Rule
Since an unsafe condition has been identified that is likely to
exist or develop on other airplanes of the same type design, this AD is
being issued to find and fix discrepancies of the seal assemblies of
the outboard leading edge slats on the wings, which could result in
cracking of the slats, subsequent separation of the cove skin,
structural damage or loss of the trailing edge wedge, and consequent
reduced controllability of the airplane. This AD requires inspections
of the outboard leading edge slats on the wings for installation of
seal assemblies with undersized (incorrect diameter) seal inserts and
missing or gapped inserts, and follow-on and corrective actions if
necessary. This AD also provides for an optional replacement of the
seal assembly in lieu of the inspections. The actions are required to
be accomplished in accordance with the service bulletin described
previously, except as discussed below.
Interim Action
At this time we are considering a separate rulemaking action to
supersede this AD to address the procedures for long-term follow-on
inspections to find additional cracking, and repair of any cracking
found, as described in the service bulletin. Due to the urgency of the
need to inspect the fleet and repair any cracking found, this AD will
address only the sections in the service bulletin that pertain to the
inspections and follow-on and corrective actions specified in Part 5
and Part 6 of the service bulletin.
In addition to superseding this AD, that rulemaking action would
also supersede AD 2002-11-06 to mandate replacement of the seal
assemblies with new seal assemblies for all 777 series airplanes.
However, the planned compliance time for these actions is sufficiently
long so that prior notice and time for public comment will be
practicable.
Differences Between This AD and the Service Bulletin
The service bulletin specifies that the manufacturer may be
contacted for disposition of certain repair conditions; however, this
AD requires the repair of those conditions to be accomplished per a
method approved by the FAA, or per data meeting the type certification
basis of the airplane approved by a Boeing Company Designated
Engineering Representative who has been authorized by the Manager,
Seattle Aircraft Certification Office, to make such findings.
Clarification of Part Numbers for Installation
Boeing Alert Service Bulletin 777-57A0034, Revision 7, dated May
22, 2003, contains certain incorrectly identified part numbers (P/N) in
the ``Existing Part Number'' and ``New Part Number'' columns of the
table under Appendix A, rows 20 and 27 of page 79, and rows 8 and 10 of
page 80; respectively. We have been advised that the manufacturer will
issue a revision to this alert service bulletin to correct the error.
The part numbers are corrected in the tables below:
Table: Part Numbers
------------------------------------------------------------------------
Existing P/N Name Correct P/N
------------------------------------------------------------------------
114W4140-21............. Slat Assy--No. 11.... 114W4140-22
114W4705-42............. Seal................. 114W4705-41
------------------------------------------------------------------------
Table: Part Numbers
------------------------------------------------------------------------
New P/N Name Correct P/N
------------------------------------------------------------------------
114W4150-23............. Slat Assy--No. 5..... 114W4150-29
114W4150-24............. Slat Assy--No. 10.... 114W4150-30
------------------------------------------------------------------------
Changes to 14 CFR Part 39/Effect on the AD
On July 10, 2002, the FAA issued a new version of 14 CFR part 39
(67 FR 47997, July 22, 2002), which governs the FAA's airworthiness
directives system. The regulation now includes material that relates to
altered products, special flight permits, and alternative methods of
compliance. Because we have now included this material in part 39, we
no longer need to include it in each individual AD; however, this AD
identifies the office authorized to approve alternative methods of
compliance.
[[Page 55195]]
Determination of Rule's Effective Date
Since a situation exists that requires the immediate adoption of
this regulation, it is found that notice and opportunity for prior
public comment hereon are impracticable, and that good cause exists for
making this amendment effective in less than 30 days.
Comments Invited
Although this action is in the form of a final rule that involves
requirements affecting flight safety and, thus, was not preceded by
notice and an opportunity for public comment, comments are invited on
this rule. Interested persons are invited to comment on this rule by
submitting such written data, views, or arguments as they may desire.
Communications shall identify the Rules Docket number and be submitted
in triplicate to the address specified under the caption ADDRESSES. All
communications received on or before the closing date for comments will
be considered, and this rule may be amended in light of the comments
received. Factual information that supports the commenter's ideas and
suggestions is extremely helpful in evaluating the effectiveness of the
AD action and determining whether additional rulemaking action would be
needed.
Submit comments using the following format:
[sbull] Organize comments issue-by-issue. For example, discuss a
request to change the compliance time and a request to change the
service bulletin reference as two separate issues.
[sbull] For each issue, state what specific change to the AD is
being requested.
[sbull] Include justification (e.g., reasons or data) for each
request.
Comments are specifically invited on the overall regulatory,
economic, environmental, and energy aspects of the rule that might
suggest a need to modify the rule. All comments submitted will be
available, both before and after the closing date for comments, in the
Rules Docket for examination by interested persons. A report that
summarizes each FAA-public contact concerned with the substance of this
AD will be filed in the Rules Docket.
Commenters wishing the FAA to acknowledge receipt of their comments
submitted in response to this rule must submit a self-addressed,
stamped postcard on which the following statement is made: ``Comments
to Docket Number 2003-NM-137-AD.'' The postcard will be date stamped
and returned to the commenter.
Regulatory Impact
The regulations adopted herein will not have a substantial direct
effect on the States, on the relationship between the national
Government and the States, or on the distribution of power and
responsibilities among the various levels of government. Therefore, it
is determined that this final rule does not have federalism
implications under Executive Order 13132.
The FAA has determined that this regulation is an emergency
regulation that must be issued immediately to correct an unsafe
condition in aircraft, and that it is not a ``significant regulatory
action'' under Executive Order 12866. It has been determined further
that this action involves an emergency regulation under DOT Regulatory
Policies and Procedures (44 FR 11034, February 26, 1979). If it is
determined that this emergency regulation otherwise would be
significant under DOT Regulatory Policies and Procedures, a final
regulatory evaluation will be prepared and placed in the Rules Docket.
A copy of it, if filed, may be obtained from the Rules Docket at the
location provided under the caption ADDRESSES.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
0
Accordingly, pursuant to the authority delegated to me by the
Administrator, the Federal Aviation Administration amends part 39 of
the Federal Aviation Regulations (14 CFR part 39) as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. Section 39.13 is amended by adding the following new airworthiness
directive:
2003-19-02 Boeing: Amendment 39-13304. Docket 2003-NM-137-AD.
Applicability: Model 777 series airplanes, line numbers 1
through 412 inclusive, certificated in any category.
Compliance: Required as indicated, unless accomplished
previously.
To prevent cracking of the leading edge outboard slats, which
could result in separation of the cove skin, structural damage or
loss of the trailing edge wedge, and consequent reduced
controllability of the airplane, accomplish the following:
Inspections and Follow-On Actions
(a) For all airplanes: Within 90 days after the effective date
of this AD; do a detailed inspection of the seal assemblies of the
outboard leading edge slats on the wings for missing or gapped
inserts; then do the applicable follow-on actions by doing all the
actions per paragraphs 1. through 7. of Part 6, ``Seal Insert Gap
Inspection and Seal Assembly Replacement,'' of the Work Instructions
of Boeing Alert Service Bulletin 777-57A0034, Revision 7, dated May
22, 2003 (including replacing the seal assembly, doing a cove skin
inspection for cracking, doing an internal inspection for cracking,
doing a slat adjustment check, repeating the cove skin and internal
inspections, replacing the slat and doing a slat adjustment check).
Any applicable follow-on actions must be done at the applicable time
specified in Figure 1, Sheets 12 through 15 inclusive, of the
service bulletin.
Note 1: For the purposes of this AD, a detailed inspection is
defined as: ``An intensive visual examination of a specific
structural area, system, installation, or assembly to detect damage,
failure, or irregularity. Available lighting is normally
supplemented with a direct source of good lighting at intensity
deemed appropriate by the inspector. Inspection aids such as mirror,
magnifying lenses, etc., may be used. Surface cleaning and elaborate
access procedures may be required.''
(b) For airplanes identified as ``Group 4'' in Boeing Alert
Service Bulletin 777-57A0034, Revision 7, dated May 22, 2003: Within
500 flight cycles after the effective date of this AD; do a detailed
inspection of the seal inserts of the seal assemblies of the
outboard leading edge slats on the wings for undersized (incorrect
diameter) seal inserts; do the applicable follow-on and corrective
actions by doing all the actions per paragraphs 1. through 8. of
Part 5, ``Seal Insert Inspection and Seal Replacement,'' of the Work
Instructions of the service bulletin. Any applicable follow-on
actions must be done at the applicable time specified in Figure 1,
Sheet 11, of the service bulletin.
Note 2: For airplanes identified as ``Group 4'' in Boeing Alert
Service Bulletin 777-57A0034, Revision 7, dated May 22, 2003
(outboard slat numbers 4, 5, 10, and 11): If a seal insert has
receded, when accomplishing paragraph (a) of this AD, operators
should be careful not to install a repair segment prior to
inspecting for an undersized diameter insert, as required by
paragraph (b) of this AD.
Corrective Actions
(c) If any discrepancy is found during any inspection required
by this AD: Before further flight, do all applicable corrective
actions specified in Part 1, Part 2, Part 3, Part 5, and Part 6 of
the Work Instructions of Boeing Alert Service Bulletin 777-57A0034,
Revision 7, dated May 22, 2003. Do the applicable corrective actions
per the service bulletin. If the service bulletin specifies to
contact the manufacturer for appropriate action: Before further
flight, repair per a method approved by the Manager, Seattle
Aircraft Certification Office (ACO), FAA, or
[[Page 55196]]
per data meeting the type certification basis of the airplane
approved by a Boeing Company Designated Engineering Representative
who has been authorized by the Manager, Seattle ACO, to make such
findings.
Part Installation
(d) As of the effective date of this AD, no one may install a
seal assembly with a part number listed in the ``Existing Part
Number'' column of the table under Appendix A of Boeing Alert
Service Bulletin 777-57A0034, Revision 7, dated May 22, 2003; on any
airplane.
Clarification of Part Numbers for Installation
(e) Boeing Alert Service Bulletin 777-57A0034, Revision 7, dated
May 22, 2003, contains certain incorrectly identified part numbers
(P/N) in the ``Existing Part Number'' and ``New Part Number''
columns of the table under Appendix A, rows 20 and 27 of page 79,
and rows 8 and 10 of page 80; respectively. This AD requires
operators to remove/install parts having the correct part numbers,
as specified in Tables 1 and 2 of this AD:
Table 1.--Part Numbers
------------------------------------------------------------------------
Existing P/N Name Correct P/N
------------------------------------------------------------------------
114W4140-21............. Slat Assy--No. 11.... 114W4140-22
114W4705-42............. Seal................. 114W4705-41
------------------------------------------------------------------------
Table 2.--Part Numbers
------------------------------------------------------------------------
New P/N Name Correct P/N
------------------------------------------------------------------------
114W4150-23............. Slat Assy--No. 5..... 114W4150-29
114W4150-24............. Slat Assy--No. 10.... 114W4150-30
------------------------------------------------------------------------
Alternative Methods of Compliance
(f)(1) In accordance with 14 CFR 39.19, the Manager, Seattle
ACO, is authorized to approve alternative methods of compliance for
this AD.
(2) An AMOC that provides an acceptable level of safety may be
used for a repair required by this AD, if it is approved by a Boeing
Company Designated Engineering Representative who has been
authorized by the Manager, Seattle ACO, to make such findings.
Incorporation by Reference
(g) Unless otherwise specified in this AD, the actions shall be
done in accordance with Boeing Alert Service Bulletin 777-57A0034,
Revision 7, dated May 22, 2003. This incorporation by reference was
approved by the Director of the Federal Register in accordance with
5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from
Boeing Commercial Airplane Group, P.O. Box 3707, Seattle, Washington
98124-2207. Copies may be inspected at the FAA, Transport Airplane
Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the
Office of the Federal Register, 800 North Capitol Street, NW., suite
700, Washington, DC.
Effective Date
(h) This amendment becomes effective on October 8, 2003.
Issued in Renton, Washington, on September 10, 2003.
Vi L. Lipski,
Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 03-23932 Filed 9-22-03; 8:45 am]
BILLING CODE 4910-13-P