[Federal Register: September 26, 2003 (Volume 68, Number 187)]
[Notices]
[Page 55594-55597]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr26se03-55]
-----------------------------------------------------------------------
DEPARTMENT OF DEFENSE
Department of the Army; Corps of Engineers
Availability of Exclusive or Partially Exclusive Licenses
AGENCY: Department of the Army, U.S. Corps of Engineers, DoD.
ACTION: Notice.
-----------------------------------------------------------------------
SUMMARY: The Department of the Army, U.S. Army Corps of Engineers,
announces the general availability of exclusive, or partially exclusive
licenses under the following pending patents listed under SUPPLEMENTARY
INFORMATION. Any license granted shall comply with 35 U.S.C. 209 and 37
CFR part 404.
ADDRESSES: Humphreys Engineer Center Support Activity, Office of
Counsel, 7701 Telegraph Road, Alexandria, VA 22315-3860.
[[Page 55595]]
DATES: Applications for an exclusive or partially exclusive license may
be submitted at any time from the date of this notice. However, no
exclusive or partially exclusive license shall be granted until
December 26, 2003.
FOR FURTHER INFORMATION CONTACT: Patricia L. Howland (703) 428-6672.
SUPPLEMENTARY INFORMATION:
1. Title: Scour Sensor Assembly. An optical scour sensor monitors
scour, including deposition and ablation, in bodies of water that may
be too lossy to enable use of electrical signals. A specially
configured optical fiber is inserted into the sediment and the
interface between the sediment and water thereby monitored using a top-
mounted control box to pulse light down the cable and capture reflected
signals. The optical fiber may be armored by a soft plastic concentric
shield and incorporate a micro-bend inducer for detecting minute
indentations in the fiber. The presence of a non-liquid, e.g.,
sediment, against the cable is detected because the sediment impinges
on the fiber causing an indentation therein. At each indentation a
reflection is sent back to the source. Using principles of optical time
domain reflectometry (OTDR), the location of the indentation is
determined. The data are fed to a remote system for processing,
analysis and display.
Serial No.: 09/878,997.
Date: 6/13/2001.
2. Title: Pattern Detection Using the Bragg Effect at RF
Frequencies. A system, and method of its use, provides for detecting
patterns that exist within a geographic area due to the presence of an
orderly array of objects. In a preferred embodiment, the system uses an
irregular array of transceivers to illuminate an area suspected of
containing a minefield. Typically, these minefields are arranged in an
orderly arrangement. Exploiting the Bragg Effect, the transceivers,
each configured as a surface wave radar, illuminate an area with RF
energy that is scanned in carrier frequency within the HF band (3-30
MHz) at a pre-specified interval. At the frequency that corresponds to
the Bragg Effect, a significantly increased signal level occurs that
indicates the presence of a pattern such as one might expect from
reflections from numerous objects arranged orderly. By processing these
returns judiciously, the minefield's size, location, perimeter, and
even the location of individual mines may be determined.
Serial No.: 60/245,2000.
Date: 11/3/2000.
3. Title: Detector and System for Indicating Pressure Change and
Methods of Use. An electronic detector configuration enables the
accurate determination of pressure differences in scenarios in which
conventional detectors and detector systems introduce inherent thermal
inequalities at the interface with their immediate environs. A
preferred embodiment of the present invention accurately measures snow
water equivalent (SWE) while eliminating the need for fluid-filled
pillows that contain environmentally hazardous fluids. By matching the
thermal conductivity of surrounding soil to a detector configuration
having an inherently low specific heat, it minimizes effects of
differences in thermal conductivity at the snow/soil interface that
cause SWE pressure sensor measurement errors. Further, it minimizes
thermal effects by keeping soil moisture under the configuration
approximately the same as that of surrounding soil. The system is
environmentally friendly, has a small footprint, and is inexpensive to
implement in arrays coupled to communicators suitable for any number of
monitoring and warning functions such as snow avalanche and landslide
early warning.
Serial No.: 10/211,582.
Date: 8/5/2002.
4. Title: Autonomous System and Method for Efficiently Collecting
Fugitive Airborne Emissions From Open Vessels. An autonomous pushed
liquid recirculation system (APLRS) is installed in a vessel, such as
an electroplating tank. It situates around the interior perimeter and
adjusts to changes in the level of liquid, maintaining the same
location and orientation respective to the liquid's surface. It
establishes a current near the surface that pushes liquid across the
narrow horizontal dimension of the tank from a front wall to a rear
wall. The current serves to push any bubbles resultant from operations
within the tank to the rear wall. Over the rear wall is mounted an
abbreviated exhaust hood covering only a short width of the surface of
the tank along the rear wall. Because the exhaust system has to
scavenge only a portion of the surface since all bubbles now burst
along the rear wall, a much smaller air handling apparatus may be
specified with an attendant savings in energy costs.
Serial No.: 10/224,232.
Date: 8/20/2002.
5. Title: Device and Method for Simulating Natural Cues so That
Waterborne Fauna Avoid Manmade Barriers. The method of adding natural
hydrodynamic cues to fish diversion screens similar to cues produced by
the flow of water over rough, stream beds is described. Fish detect the
cues and avoid contacting or impinging on the screen surface in the
same way that they avoid collision with natural features of stream
channels. One design features that uses the method of adding natural
cues is described. The feature consists of a series of rectangular
plates that are attached to the u-clips beneath diversion screens that
provide structural support to the individual bars that comprise the
screen. The plates are oriented so that they are approximately
perpendicular to the flow lines approaching the screen surface. The
flow contacts the plates and, because the orientation of the plate
creates an unstable hydraulic field, the flow alternately slips above
and below the plates. This hydrodynamic oscillation extends above the
screen surface and creates fluctuating local acceleration zones. These
small-scale flow instabilities can be detected by fish prior to their
contact with the screen surface and will cause the fish to navigate
away from the screen surface without contacting the screen. Fish are
guided by the signals generated by the screen reducing the danger of
injury or death by collision with the screen surface or supporting
structure.
Serial No.: 10/226,555.
Date: 8/20/2002.
6. Title: Bullet Trapping Medium and System. A backstop for
decelerating and trapping projectiles generally includes a support
structure having an inclined surface and a projectile trapping medium
disposed on the inclined surface. The projectile trapping medium may be
either a resilient granular ballistic medium or a combination of a
ballistic medium with a hydrated super absorbent polymer (SAP) gel.
Preferably, the support structure is made of a shock absorbing, foamed,
fiber-reinforced concrete, such as SACON. In embodiments, the support
structure also includes an enclosure. Additives may also be mixed into
the projectile trapping medium to control alkalinity and prevent
leaching of heavy metals.
Serial No.: 10/307,427.
Date: 12/2/2002.
7. Title: Methods and Devices for Optically Recording and Imaging
Representations of Interactions of an Object With its Environment.
Using an array of optical sensors affixed to measure interactions on a
surface of an object, in combination with a specially configured
personal computer, dynamic mapping of interaction is provided. One
application maps washover of an object towed in a large body of water.
Data are collected on optical characteristics of the interaction such
as reflectivity at a boundary. For example, in one
[[Page 55596]]
embodiment the reflectivity at an optical fiber/seawater boundary is
compared to that of an optical fiber/air boundary and dynamic
measurements made using an optical time domain reflectometer (OillR).
These data are then processed using specialized software to yield
representation of the dynamics (spatial and temporal) of selected
washover events on a surface of interest. The system specifically
provides a real-time representation of washover, including two and
three-dimensional visualization of washover, as well as recording
selected data for future use. Methods of employment of the system are
also provided.
Serial No.: 10/318,129.
Date: 12/13/2002.
8. Title: Systems, and Methods of Use, Employing Distorted Patterns
to ascertain the Shape of a Surface, for Road or Runway Profiling, or
as Input to Control Pro-active Suspension Systems. Provided in a
preferred embodiment is an application of phase or ``shadow''
profilometry to determine a 3-D profile of structure instantaneously.
In one application, a vehicle-mounted system captures a 3-D profile
while operating normally. The system may use a digital camera, a
computer for processing and storage, a broadband light source, and a
device positioned between the light and structure that enables strips
of light to impinge on the structure. A preferred embodiment uses a
single straight edge as the device, casting a straight line shadow. In
addition to profiling road surfaces, the bottom of hydraulic models
have been profiled even while being disturbed with a wave generator. It
may be integrated with other devices such as a pro-active suspension
system for civilian, military, and construction vehicles. Further, use
with tiltmeters and GPS receivers provides data useful for engineering
or construction management.
Serial No.: 10/318,214.
Date: 12/13/2002.
9. Title: Method and Instrument for Electronically Recording, and
Imaging Representations of Interactions of an Object With its
Environment. Using an array of electrically isolated electrode pairs in
combination with a specially configured processor, e.g., a personal
computer, continuous real-time acquisition, processing, mapping and
visualization of an object's interaction with its environment are
provided. In a specific application, washover data are collected on
salient electrical characteristics of seawater accumulating between
electrodes of an electrode pair, one of which may be a common ground
plane. For example, in one embodiment, the resistance of seawater is
measured dynamically at each electrode pair. These data are then
processed using specialized software to yield representation of the
dynamics of selected washover events on a surface of interest.
Described systems specifically provide real-time spatial and temporal
representations of interaction, including two and three-dimensional
visualization of the interaction, e.g., washover, as well as recording
selected data for future use. Methods of employment of the systems are
also provided.
Serial No.: 10/318,297.
Date: 12/13/2002.
10. Title: Self-Healing Coating and Microcapsules to Make Same. A
liquid self-healing coating, incorporating microcapsules filled with
tailored repair formulations, repairs itself upon physical compromise
after curing. In one embodiment, a commercially available paint primer
is mixed with a pre-specified amount of these microcapsules. After the
coating has cured on the substrate to which it is applied, any physical
compromise of the cured coating results in the microcapsules bursting
to release a liquid that fills and seals the compromised volume of the
coating. In applications where paint is used to provide corrosion
protection, the liquid contains anti-corrosion material as well as
suitable diluents and film-forming compounds. In another embodiment,
the microcapsules may be provided separately to enhance commercially
available products. For example, if a paint formulation is known a
priori, specifically configured microcapsules packaged separately from
the paint and designed for use with the paint formulation, may be added
to the commercially available product just prior to application.
Serial No.: 10/377,642.
Date: 3/4/2003.
11. Title: Fusion of Data From Differing Mathematical Models. A
procedure automatically resolves vertical differences commonly found
when merging and combining Digital Elevation Models (DEMs) from
different collection and production systems. These systems may employ
technologies used in single pass Interferometric Synthetic Aperture
Radar (IFSAR), Light Detection And Ranging (LIDAR), and photogrammetry,
as well as DEMs derived from contour based elevation data and GPS point
data. This procedure employs sophisticated software checking routines
for automatically identifying horizontal and vertical datums used by
the differing systems as well as any geoid models employed by them.
Normally, all of these sources use different vertical datums and may
use different horizontal datums. A preferred embodiment of the present
invention automatically recognizes the vertical datums, including those
that are associated with the geoid models and the 3-D datums that
conventional GIS does not support at present.
Serial No.: 10/395,168.
Date: 3/25/2003.
12. Title: Detecting, Classifying, and Localizing Minor Amounts of
an Element Within a Sample of Material. Minute amounts of material,
such as a contaminant, are detected, identified and located using a
single procedure that eliminates the need for using complex and
sometimes redundant instrumentation setups, multiple (and sometimes
overlapping) analytic processes, or both. In a preferred embodiment, a
series of processing steps enables one to detect, identify, and
localize minute amounts of particular elements, e.g., contaminants, in
material being tested. Data sets, suitable for characterizing
components of samples at least spectrally and spatially, are collected
from at least one uncontaminated sample of material (the ``baseline''
or ``control'') and a sample of material under test (MUT) that may
contain contaminants. Comparison of these data sets, using the
procedures of the present invention, enables ready identification of
minute amounts of material in any sample. The use of existing
conventional procedures may require that multiple sets of data be taken
or multiple processes be applied.
Serial No.: 10/406,159.
Date: 4/3/2003.
13. Title: Improved Method and System for Dewatering Particulate
Materials. A system and method for dewatering particulate materials
employs an improved dewatering probe generally including a single non-
conducting pipe having a plurality of holes or slots, an anode mounted
on the pipe adjacent one end of the pipe, and a cathode mounted on the
pipe adjacent the opposite end of the pipe. The pipe serves as both a
sonde for mounting the anode and cathode and as a well for extracting
water that collects around the outside of the pipe and flows into the
interior of the pipe through the holes or slots via gravitational and
electro-osmotic forces. A pump may be used to extract both collected
water and accumulated electrolytic gases from the pipe's interior. In
embodiments, an array of guide electrodes is mounted on the pipe in
addition to the anode and the cathode in order to deflect the major
current flow out into the body of surrounding particulate materials.
The guide electrodes also facilitate rapid
[[Page 55597]]
depolarization of the probe. An array of probes according to the
present invention may be employed as a system to dewater a volume of
particulate.
Serial No.: 10/421,922.
Date: 4/24/2003.
14. Title: Devices and Methods for Reducing or Eliminating the Gap
Between a Stay Vane and its Corresponding Wicket Gate as Used in
Turbines. An improved design for turbines increases efficiency while
reducing potential for fish kill. In a preferred embodiment as relates
to a Kaplan turbine, the gap between stay vanes and their corresponding
wicket gates is reduced or eliminated by provision of an extension to
the trailing edge of the stay vane. In alternative embodiments, the
extension may be added to the wicket gate or affixed to both in an
arrangement that permits free movement of the wicket gate. To
facilitate eliminating the gap altogether, the extension may be made of
a pliable material or be fabricated in a telescoping or accordion
arrangement to permit contact with opposing parts without damage
thereto. By designing extensions using accepted hydraulic principles, a
better fit of the stay vane to its associated wicket gate, and possibly
to the turbines runners may be effected, further improving operational
efficiency and possibly even extending maintenance intervals.
Serial No.: 60/442,551.
Date: 1/27/2003.
Luz D. Ortiz,
Army Federal Register Liaison Officer.
[FR Doc. 03-24255 Filed 9-25-03; 8:45 am]
BILLING CODE 3710-92-P