[Federal Register: January 29, 2004 (Volume 69, Number 19)]
[Proposed Rules]
[Page 4261-4263]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr29ja04-21]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. 2003-NM-157-AD]
RIN 2120-AA64
Airworthiness Directives; Bombardier Model CL-600-2B19 (Regional
Jet Series 100 & 440) Airplanes
AGENCY: Federal Aviation Administration, DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: This document proposes the adoption of a new airworthiness
directive (AD) that is applicable to certain Bombardier Model CL-600-
2B19 (Regional Jet series 100 & 440) airplanes. This proposal would
require replacement of landing gear control handle components with new,
improved components. This action is necessary to prevent an inability
to lower or retract the landing gear using the landing gear control
handle, which could result in use of Emergency Procedures using the
landing gear manual release. This action is intended to address the
identified unsafe condition.
DATES: Comments must be received by March 1, 2004.
ADDRESSES: Submit comments in triplicate to the Federal Aviation
Administration (FAA), Transport Airplane Directorate, ANM-114,
Attention: Rules Docket No. 2003-NM-157-AD, 1601 Lind Avenue, SW.,
Renton, Washington 98055-4056. Comments may be inspected at this
location between 9 a.m. and 3 p.m., Monday through Friday, except
Federal holidays. Comments may be submitted via fax to (425) 227-1232.
Comments may also be sent via the Internet using the following address:
9-anm-nprmcomment@faa.gov. Comments sent via fax or the Internet must
contain ``Docket No. 2003-NM-157-AD'' in the subject line and need not
be submitted in triplicate. Comments sent via the Internet as attached
electronic files must be formatted in Microsoft Word 97 for Windows or
ASCII text.
The service information referenced in the proposed rule may be
obtained from
[[Page 4262]]
Bombardier, Inc., Canadair, Aerospace Group, P.O. Box 6087, Station
Centre-ville, Montreal, Quebec H3C 3G9, Canada. This information may be
examined at the FAA, Transport Airplane Directorate, 1601 Lind Avenue,
SW., Renton, Washington; or at the FAA, New York Aircraft Certification
Office, 1600 Stewart Avenue, Westbury, New York.
FOR FURTHER INFORMATION CONTACT: Dan Parrillo, Aerospace Engineer,
Systems and Flight Test Branch, ANE-172, FAA, New York Aircraft
Certification Office, 1600 Stewart Avenue, Westbury, New York, 11590;
telephone (516) 228-7305; fax (516) 794-5531.
SUPPLEMENTARY INFORMATION:
Comments Invited
Interested persons are invited to participate in the making of the
proposed rule by submitting such written data, views, or arguments as
they may desire. Communications shall identify the Rules Docket number
and be submitted in triplicate to the address specified above. All
communications received on or before the closing date for comments,
specified above, will be considered before taking action on the
proposed rule. The proposals contained in this action may be changed in
light of the comments received.
Submit comments using the following format:
Organize comments issue-by-issue. For example,
discuss a request to change the compliance time and a request to change
the service bulletin reference as two separate issues.
For each issue, state what specific change to
the proposed AD is being requested.
Include justification (e.g., reasons or data)
for each request.
Comments are specifically invited on the overall regulatory,
economic, environmental, and energy aspects of the proposed rule. All
comments submitted will be available, both before and after the closing
date for comments, in the Rules Docket for examination by interested
persons. A report summarizing each FAA-public contact concerned with
the substance of this proposal will be filed in the Rules Docket.
Commenters wishing the FAA to acknowledge receipt of their comments
submitted in response to this action must submit a self-addressed,
stamped postcard on which the following statement is made: ``Comments
to Docket Number 2003-NM-157-AD.'' The postcard will be date stamped
and returned to the commenter.
Availability of NPRMs
Any person may obtain a copy of this NPRM by submitting a request
to the FAA, Transport Airplane Directorate, ANM-114, Attention: Rules
Docket No. 2003-NM-157-AD, 1601 Lind Avenue, SW., Renton, Washington
98055-4056.
Discussion
Transport Canada Civil Aviation (TCCA), which is the airworthiness
authority for Canada, notified the FAA that an unsafe condition may
exist on certain Bombardier Model CL-600-2B19 (Regional Jet series 100
& 440) airplanes. TCCA advises that there have been two in-flight
incidents where the slider within the landing gear control handle
(LGCH) fractured during gear selection. This condition, if not
corrected, could result in an inability to lower or retract the landing
gear using the LGCH, which could result in use of Emergency Procedures
using the landing gear manual release.
Explanation of Relevant Service Information
Bombardier has issued Service Bulletin 601R-32-084, dated May 17,
2002, which describes procedures for replacing the landing gear control
handle with a new landing gear handle, which eliminates the need for
temporary periodic inspections for the existing landing gear control
handle. Accomplishment of the actions specified in the service bulletin
is intended to adequately address the identified unsafe condition. TCCA
classified this service bulletin as mandatory and issued Canadian
airworthiness directive CF-2003-03, dated February 3, 2003, in order to
assure the continued airworthiness of these airplanes in Canada.
FAA's Conclusions
This airplane model is manufactured in Canada and is type
certificated for operation in the United States under the provisions of
Sec. 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and the
applicable bilateral airworthiness agreement. Pursuant to this
bilateral airworthiness agreement, TCCA has kept the FAA informed of
the situation described above. The FAA has examined the findings of
TCCA, reviewed all available information, and determined that AD action
is necessary for products of this type design that are certificated for
operation in the United States.
Explanation of Requirements of Proposed Rule
Since an unsafe condition has been identified that is likely to
exist or develop on other airplanes of the same type design registered
in the United States, the proposed AD would require accomplishment of
the actions specified in the service bulletin described previously,
except as discussed below.
Difference Between Proposed Rule and Referenced Service Bulletin
Operators should note that, although the Accomplishment
Instructions of the referenced service bulletin describe procedures for
completing and submitting a comment sheet related to service bulletin
quality and a sheet recording compliance with the service bulletin,
this proposed AD would not require those actions. The FAA does not need
this information from operators.
Cost Impact
The FAA estimates that 184 airplanes of U.S. registry would be
affected by this proposed AD, that it would take approximately 1 work
hour per airplane to accomplish the proposed replacement, and that the
average labor rate is $65 per work hour. Based on these figures, the
cost impact of the proposed AD on U.S. operators is estimated to be
$11,960, or $65 per airplane.
The cost impact figure discussed above is based on assumptions that
no operator has yet accomplished any of the proposed requirements of
this AD action, and that no operator would accomplish those actions in
the future if this proposed AD were not adopted. The cost impact
figures discussed in AD rulemaking actions represent only the time
necessary to perform the specific actions actually required by the AD.
These figures typically do not include incidental costs, such as the
time required to gain access and close up, planning time, or time
necessitated by other administrative actions. The manufacturer may
cover the cost of replacement parts associated with this proposed AD,
subject to warranty conditions.
Regulatory Impact
The regulations proposed herein would not have a substantial direct
effect on the States, on the relationship between the national
Government and the States, or on the distribution of power and
responsibilities among the various levels of government. Therefore, it
is determined that this proposal would not have federalism implications
under Executive Order 13132.
For the reasons discussed above, I certify that this proposed
regulation (1) is not a ``significant regulatory action'' under
Executive Order 12866; (2) is not a ``significant rule'' under the DOT
[[Page 4263]]
Regulatory Policies and Procedures (44 FR 11034, February 26, 1979);
and (3) if promulgated, will not have a significant economic impact,
positive or negative, on a substantial number of small entities under
the criteria of the Regulatory Flexibility Act. A copy of the draft
regulatory evaluation prepared for this action is contained in the
Rules Docket. A copy of it may be obtained by contacting the Rules
Docket at the location provided under the caption ADDRESSES.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, pursuant to the authority delegated to me by the
Administrator, the Federal Aviation Administration proposes to amend
part 39 of the Federal Aviation Regulations (14 CFR part 39) as
follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. Section 39.13 is amended by adding the following new
airworthiness directive:
Bombardier, Inc. (Formerly Canadair): Docket 2003-NM-157-AD.
Applicability: Model CL-600-2B19 (Regional Jet Series 100 & 440)
airplanes, serial numbers 7375 through 7632 inclusive, certificated
in any category; equipped with landing gear control handle
assemblies, Canadair Part Number (P/N) 601R50967-7 (Vendor P/N 7-
45502-1) or Canadair P/N 601R50967-9 (Vendor P/N 7-45502-3).
Compliance: Required as indicated, unless accomplished
previously.
To prevent an inability to lower or retract the landing gear
using the landing gear control handle, which could result in use of
Emergency Procedures using the landing gear manual release,
accomplish the following:
Replacement
(a) Within 5,000 flight cycles after the effective date of this
AD, or within one year after the effective date of this AD,
whichever occurs first; replace the landing gear control handle with
a new landing gear control handle, Canadair P/N 601R50967-11 (Vendor
P/N 7-45502-5), per the Accomplishment Instructions of Bombardier
Service Bulletin 601R-32-084, dated May 17, 2002.
Exception to Service Bulletin Reporting
(b) Although the service bulletin referenced in this AD
specifies to submit certain information to the manufacturer, this AD
does not include such a requirement.
Maintenance Requirements Manual Revision
(c) Accomplishment of the actions in paragraph (a) of this AD
constitutes terminating action for periodic crack inspections, as
specified in Temporary Revision 2B-627 of Part 2 of the Maintenance
Requirements Manual, Appendix B, Airworthiness Limitations.
Alternative Methods of Compliance
(d) In accordance with 14 CFR 39.19, the Manager, New York
Aircraft Certification Office (ACO), FAA, is authorized to approve
alternative methods of compliance for this AD.
Note 1: The subject of this AD is addressed in Canadian
airworthiness directive CF-2003-03, dated February 3, 2003.
Issued in Renton, Washington, on January 20, 2004.
Kalene C. Yanamura,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 04-1911 Filed 1-28-04; 8:45 am]
BILLING CODE 4910-13-P