[Federal Register: December 16, 2004 (Volume 69, Number 241)]
[Proposed Rules]
[Page 75277-75280]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr16de04-17]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2004-19867; Directorate Identifier 2004-NM-58-AD]
RIN 2120-AA64
Airworthiness Directives; McDonnell Douglas Model MD-90-30
Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD)
for all McDonnell Douglas Model MD-90-30 airplanes. This proposed AD
would require replacing existing dual anti-skid control manifolds
(DACM) with new, improved or reworked and reidentified DACMs;
inspecting the inlet filters and other components of the DACMs for
damage; replacing any damaged DACM components with new or serviceable
components; and flushing/cleaning the braking system prior to replacing
the inlet filters. This proposed AD is prompted by reports of multiple
incidents of blown tires on landing while using maximum autobrake. We
are proposing this AD to prevent metallic fibers from the first stage
filter of the servo valves inside the DACM from becoming lodged in the
first stage nozzle of the servo valve, which could lead to tire failure
during high speed/
[[Page 75278]]
high energy braking and possible subsequent runway departure.
DATES: We must receive comments on this proposed AD by January 31,
2005.
ADDRESSES: Use one of the following addresses to submit comments on
this proposed AD.
DOT Docket Web site: Go to http://dms.dot.gov and follow
the instructions for sending your comments electronically.
Government-wide rulemaking Web site: Go to http://www.regulations.gov
and follow the instructions for sending your
comments electronically.
Mail: Docket Management Facility, U.S. Department of
Transportation, 400 Seventh Street, SW., Nassif Building, Room PL-401,
Washington, DC 20590.
By fax: (202) 493-2251.
Hand Delivery: Room PL-401 on the plaza level of the
Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
For service information identified in this proposed AD, contact
Boeing Commercial Airplanes, Long Beach Division, 3855 Lakewood
Boulevard, Long Beach, California 90846, Attention: Data and Service
Management, Dept. C1-L5A (D800-0024).
You can examine the contents of this AD docket on the Internet at
http://dms.dot.gov, or in person at the Docket Management Facility,
U.S. Department of Transportation, 400 Seventh Street, SW., Room PL-
401, on the plaza level of the Nassif Building, Washington, DC. This
docket number is FAA-2004-19867; the directorate identifier for this
docket is 2004-NM-58-AD.
FOR FURTHER INFORMATION CONTACT:
Technical information: Cheyenne Del Carmen, Aerospace Engineer,
Cabin Safety, Mechanical & Environmental Branch, ANM-150L, FAA, Los
Angeles Aircraft Certification Office, 3960 Paramount Boulevard,
Lakewood, California 90712-4137; telephone (562) 627-5338; fax (562)
627-5210.
Plain language information: Marcia Walters, marcia.walters@faa.gov.
SUPPLEMENTARY INFORMATION:
Docket Management System (DMS)
The FAA has implemented new procedures for maintaining AD dockets
electronically. As of May 17, 2004, new AD actions are posted on DMS
and assigned a docket number. We track each action and assign a
corresponding directorate identifier. The DMS AD docket number is in
the form ``Docket No. FAA-2004-99999.'' The Transport Airplane
Directorate identifier is in the form ``Directorate Identifier 2004-NM-
999-AD.'' Each DMS AD docket also lists the directorate identifier
(``Old Docket Number'') as a cross-reference for searching purposes.
Comments Invited
We invite you to submit any written relevant data, views, or
arguments regarding this proposed AD. Send your comments to an address
listed under ADDRESSES. Include ``Docket No. FAA-2004-19867;
Directorate Identifier 2004-NM-58-AD'' in the subject line of your
comments. We specifically invite comments on the overall regulatory,
economic, environmental, and energy aspects of the proposed AD. We will
consider all comments submitted by the closing date and may amend the
proposed AD in light of those comments.
We will post all comments we receive, without change, to http://dms.dot.gov
, including any personal information you provide. We will
also post a report summarizing each substantive verbal contact with FAA
personnel concerning this proposed AD. Using the search function of
that Web site, anyone can find and read the comments in any of our
dockets, including the name of the individual who sent the comment (or
signed the comment on behalf of an association, business, labor union,
etc.). You may review DOT's complete Privacy Act Statement in the
Federal Register published on April 11, 2000 (65 FR 19477-78), or you
may visit http://dms.dot.gov.
We are reviewing the writing style we currently use in regulatory
documents. We are interested in your comments on whether the style of
this document is clear, and your suggestions to improve the clarity of
our communications that affect you. You can get more information about
plain language at http://www.faa.gov/language and http://www.plainlanguage.gov.Examining
the Docket
You can examine the AD docket in person at the Docket Management
Facility office between 9 a.m. and 5 p.m., Monday through Friday,
except Federal holidays. The Docket Management Facility office
(telephone (800) 647-5227) is located on the plaza level of the Nassif
Building at the DOT street address stated in the ADDRESSES section.
Comments will be available in the AD docket shortly after the DMS
receives them.
Discussion
We have received reports of multiple incidents of blown tires on
landing while using maximum autobrake on McDonnell Douglas Model MD-90-
30 airplanes. The reports indicate that, due to filter contamination,
structural damage, or excessive wear, metallic fibers from the first
stage filter of the servo valves inside the dual anti-skid control
manifold (DACM) are becoming lodged in the first stage nozzle of the
servo valve. This condition, if not corrected, could result in tire
failure during high speed/high energy braking and possible subsequent
runway departure.
Relevant Service Information
We have reviewed McDonnell Douglas Service Bulletin MD90-32-056,
dated October 7, 2003. The service bulletin describes procedures for
replacing existing DACMs with new, improved or reworked and
reidentified DACMs.
Service Bulletin MD90-32-056 specifies prior or concurrent
accomplishment of McDonnell Douglas Service Bulletin MD90-32-043,
Revision 01, dated November 9, 2000.
We have reviewed Service Bulletin MD90-32-043, which describes
procedures for replacing the metered pressure inlet filters of the DACM
with new filters. Service Bulletin MD90-32-043 also describes
procedures for inspecting the inlet filters and other components of the
DACM for damage, and flushing/cleaning the braking system prior to
replacing the inlet filters.
Accomplishing the actions specified in the service information is
intended to adequately address the unsafe condition.
Service Bulletin MD90-32-056 refers to Aircraft Braking Systems
Corporation (ABSC) Service Bulletin MD-90 6006079-32-02, dated August
7, 2003, as an additional source of service information for reworking
and reidentifying DACMs.
Service Bulletin MD90-32-043 refers to ABSC Service Bulletin MD90-
32-12, dated January 12, 2000, as an additional source of service
information for inspecting components of the DACM for cleanliness,
structural damage, or excessive wear, and replacing any damaged
components with new or serviceable components.
FAA's Determination and Requirements of the Proposed AD
We have evaluated all pertinent information and identified an
unsafe condition that is likely to exist or develop on other airplanes
of this same type design. Therefore, we are proposing this AD, which
would require replacing DACMs with new, improved or reworked and
reidentified DACMs;
[[Page 75279]]
inspecting the inlet filters and other components of the DACMs for
damage; replacing any damaged DACM components with new or serviceable
components; and flushing/cleaning the braking system prior to replacing
the inlet filters; in accordance with Service Bulletin MD90-32-056,
dated October 7, 2003, and Service Bulletin MD90-32-043, Revision 01,
dated November 9, 2000; except as discussed under ``Differences Between
Service Information and the Proposed AD.''
Differences Between Service Information and the Proposed AD
Although Service Bulletin MD90-32-056 recommends that ``operators
do this service bulletin at a scheduled maintenance period when
manpower, materials, and facilities are available,'' we have determined
that this imprecise compliance time would not address the identified
unsafe condition in a timely manner. In developing an appropriate
compliance time for this proposed AD, we considered not only the
manufacturer's recommendation, but also the degree of urgency
associated with addressing the subject unsafe condition, the average
utilization of the affected fleet, and the time necessary to perform
the modifications. In light of all of these factors, we find a
compliance time of 18 months for completing the required actions to be
warranted, in that it represents an appropriate interval of time for
affected airplanes to continue to operate without compromising safety.
Although Service Bulletin MD90-32-043, Revision 01, specifies
inspecting the DACM assembly inlet filters for damage, this proposed AD
would require a detailed inspection of the filters to eliminate any
possible confusion about the proper type of inspection. Note 3 of this
proposed AD includes a definition of this type of inspection.
Costs of Compliance
This proposed AD would affect about 115 airplanes worldwide and 24
airplanes of U.S. registry. The proposed actions would take about 8
work hours per airplane, at an average labor rate of $65 per work hour.
Required parts would cost between $8,000 and $240,780 per airplane.
Based on these figures, the estimated cost of the proposed AD for U.S.
operators is between $204,480 and $5,791,200, or between $8,520 and
$241,300 per airplane.
Regulatory Authority and Findings
This rulemaking is promulgated under the authority described in
subtitle VII, part A, subpart III, section 44701, General requirements.
Under that section, the FAA is charged with prescribing regulations for
practices, methods, and procedures the Administrator finds necessary
for safety and air commerce. This regulation is within the scope of
that authority because it addresses an unsafe condition that is likely
to exist or develop on products identified in this AD.
We have determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the National Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify that the proposed
regulation:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this proposed AD. See the ADDRESSES section for a location
to examine the regulatory evaluation.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. The FAA amends Sec. 39.13 by adding the following new
airworthiness directive (AD):
McDonnell Douglas: Docket No. FAA-2004-19867; Directorate Identifier
2004-NM-58-AD.
Comments Due Date
(a) The Federal Aviation Administration (FAA) must receive
comments on this AD action by January 31, 2005.
Affected ADs
(b) None.
Applicability
(c) This AD applies to all McDonnell Douglas Model MD-90-30
airplanes, certificated in any category.
Unsafe Condition
(d) This AD was prompted by reports of multiple incidents of
blown tires on landing while using maximum autobrake. We are issuing
this AD to prevent metallic fibers from the first stage filter of
the servo valves inside the dual anti-skid control manifolds (DACM)
from becoming lodged in the first stage nozzle of the servo valve,
which could lead to tire failure during high speed/high energy
braking and possible subsequent runway departure.
Compliance
(e) You are responsible for having the actions required by this
AD performed within the compliance times specified, unless the
actions have already been done.
Replacement of DACMs
(f) Within 18 months after the effective date of this AD,
replace existing DACMs with new, improved or reworked and
reidentified DACMs, part number 6006079-2, by doing all actions in
accordance with the Accomplishment Instructions of McDonnell Douglas
Service Bulletin MD90-32-056, dated October 7, 2003.
Note 1: McDonnell Douglas Service Bulletin MD90-32-056 refers to
Aircraft Braking Systems Corporation (ABSC) Service Bulletin MD-90
6006079-32-02, dated August 7, 2003, as an additional source of
service information for installing new, improved or reworked and
reidentified DACMs.
Concurrent Service Bulletin
(g) Prior to or concurrent with the accomplishment of paragraph
(f) of this AD, perform paragraphs (g)(1) and (g)(2) of this AD in
accordance with the Accomplishment Instructions of McDonnell Douglas
Service Bulletin MD90-32-043, Revision 01, dated November 9, 2000.
(1) Perform a detailed inspection of the metered pressure inlet
filters and other components of the DACM for damage. Replace any
damaged DACM components with new or serviceable components, and
flush/clean the braking system, as applicable.
(2) Replace the metered pressure inlet filters of the DACM
assembly with new filters.
Note 2: McDonnell Douglas Service Bulletin MD90-32-043, Revision
01, refers to ABSC Service Bulletin MD90-32-12, dated January 12,
2000, as an additional source of service information for inspecting
the components of the DACM assembly for uncleanliness, structural
damage or excessive wear that may render the DACM inoperable, and
for replacing those components with new or serviceable components,
if necessary.
Note 3: For the purposes of this AD, a detailed inspection is
``an intensive examination of a specific item, installation, or
assembly to detect damage, failure, or irregularity. Available
lighting is normally supplemented with a direct source of good
[[Page 75280]]
lighting at an intensity deemed appropriate. Inspection aids such as
mirror, magnifying lenses, etc. may be necessary. Surface cleaning
and elaborate procedures may be required.''
Prior Inspection/Replacement of Inlet Filters
(h) Inspecting and replacing DACM inlet filters and flushing/
cleaning braking systems before the effective date of this AD in
accordance with McDonnell Douglas Service Bulletin MD90-32-043,
dated April 10, 2000, is considered acceptable for compliance with
the corresponding actions specified in this AD.
Alternative Methods of Compliance (AMOCs)
(i) The Manager, Los Angeles Aircraft Certification Office, FAA,
has the authority to approve AMOCs for this AD, if requested using
the procedures found in 14 CFR 39.19.
Issued in Renton, Washington, on December 6, 2004.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 04-27512 Filed 12-15-04; 8:45 am]
BILLING CODE 4910-13-U