[Federal Register: July 11, 2005 (Volume 70, Number 131)]
[Rules and Regulations]
[Page 39639-39642]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr11jy05-1]
========================================================================
Rules and Regulations
Federal Register
________________________________________________________________________
This section of the FEDERAL REGISTER contains regulatory documents
having general applicability and legal effect, most of which are keyed
to and codified in the Code of Federal Regulations, which is published
under 50 titles pursuant to 44 U.S.C. 1510.
The Code of Federal Regulations is sold by the Superintendent of Documents.
Prices of new books are listed in the first FEDERAL REGISTER issue of each
week.
========================================================================
[[Page 39639]]
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2004-19795; Directorate Identifier 2004-NM-196-AD;
Amendment 39-14181; AD 2005-14-04]
RIN 2120-AA64
Airworthiness Directives; Boeing Model 777-200 and -300 Series
Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The FAA is adopting a new airworthiness directive (AD) for
certain Boeing Model 777-200 and -300 series airplanes. This AD
requires replacing the existing halogen lamps in the cargo compartment
light assemblies with new incandescent lamps, and installing warning
and identification placards. This AD is prompted by a report of an aft
cargo fire during flight. We are issuing this AD to prevent a fire in
the cargo compartment.
DATES: This AD becomes effective August 15, 2005.
The incorporation by reference of certain publications listed in
the AD is approved by the Director of the Federal Register as of August
15, 2005.
ADDRESSES: For service information identified in this AD, contact
Boeing Commercial Airplanes, P.O. Box 3707, Seattle, Washington 98124-
2207.
Docket: The AD docket contains the proposed AD, comments, and any
final disposition. You can examine the AD docket on the Internet at
http://dms.dot.gov, or in person at the Docket Management Facility
office between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The Docket Management Facility office (telephone (800) 647-
5227) is located on the plaza level of the Nassif Building at the U.S.
Department of Transportation, 400 Seventh Street, SW., room PL-401,
Washington, DC. This docket number is FAA-2004-19795; the directorate
identifier for this docket is 2004-NM-196-AD.
FOR FURTHER INFORMATION CONTACT: Clint Jones, Aerospace Engineer, Cabin
Safety and Environmental Systems Branch, ANM-150S, FAA, Seattle
Aircraft Certification Office, 1601 Lind Avenue, SW., Renton,
Washington 98055-4056; telephone (425) 917-6471; fax (425) 917-6590.
SUPPLEMENTARY INFORMATION: The FAA proposed to amend 14 CFR part 39
with an AD for certain Boeing Model 777-200 and -300 series airplanes.
That action, published in the Federal Register on December 3, 2004 (69
FR 70202), proposed to require replacing the existing halogen lamps in
the cargo compartment light assemblies with new incandescent lamps, and
installing warning and identification placards.
Comments
We provided the public the opportunity to participate in the
development of this AD. We have considered the comments that have been
submitted on the proposed AD.
Support for the Proposal
Several commenters support the proposal. One commenter, an airplane
operator, estimates that the proposed actions for its fleet would take
approximately 6.25 man hours per airplane at a cost of $569. We agree
that this cost estimate is in line with the estimate provided in the
proposal.
Request To Allow Replacement According to a Specified Standard
One commenter, an airplane operator, agrees with the intent of the
proposal, but requests that the proposal be revised to allow operators
to use incandescent replacement lamps that meet a certain design
specification, rather than those that have a particular part number.
We agree with the commenter; many incandescent lamps are
manufactured to industry standards, and would adequately address the
unsafe condition. The American National Standards Institute (ANSI)
gives specifications for the lamps that include rated voltage, rated
life, current or wattage, mean spherical candela, bulb diameter, and
base design. All of these specifications are considered critical for
lamps that are used in the affected airplanes. We have revised
paragraph (f) of the final rule to allow operators the option to use
lamps that meet the ANSI standard.
Request To Clarify Part Number
The same commenter requests that we revise the proposal to add
known, manufacturer-internal part numbers for the light bulbs listed in
the proposal. This suggested change is intended to promote awareness
and compliance with the AD.
We agree with the commenter. The airplane manufacturer's service
bulletin and the part assembly manufacturer's service bulletin each
have a separate part number that refers to the same part, which could
cause confusion. We have revised paragraph (g) of the final rule to
include both part numbers.
Request To Address Light Bulbs Changed Before Compliance Date of AD
The same commenter requests that we change the proposal to address
the modification of the light assembly that would be required should a
halogen lamp fail and need replacement prior to the end of the
compliance period of the AD. We infer that the commenter is pointing
out that any halogen lamp could be replaced with another halogen lamp
before operators must replace them all with new incandescent lamps in
the entire cargo area.
We agree with the commenter. It is likely that the situation the
commenter describes will happen. The change to paragraph (g) described
in the above paragraph titled ``Request to Clarify Part Number,'' and
the addition of the words ``As of 18 months after the effective date of
this AD,'' to that same paragraph, will ensure that no halogen lamps
are installed in the cargo ceiling light assemblies after the
compliance period of the AD.
Request To Include Additional Lighting Assembly
One commenter, another airplane operator, requests that we include
in the proposal a requirement to change the lamp in the airplane's bulk
cargo door sill. The commenter points out that this lamp also could be
an ignition source. The commenter also is concerned that two different
lamp installations and
[[Page 39640]]
inventory stocks for the same compartment of the airplane could cause
confusion and potential opportunity to mix the bulbs.
We partially agree with the commenter's request. We agree that
there could be opportunity to mix lamps if the operator does not follow
the placarded directions on the re-worked light assemblies. However, a
number of factors will minimize this possibility. First, the lights are
placarded, and maintenance personnel should look at the removed part
(or lamp) and compare it to the replacement lamp. Second, the
illustrated parts catalogue has been updated to show the new lamps and
the corresponding installation locations. Third, the lamp intensities
and hues are different. Finally, we disagree that the sill light is an
ignition source because there is a required cargo net that acts as a
barrier and protects the door and sill area; therefore, properly loaded
cargo should not come into contact with the cargo door sill light
because it is located between the cargo net and the bulk cargo door. We
have not changed the final rule in this regard. However, we have
revised paragraph (g) of the final rule to clarify that the door sill
light is not affected by the requirements of that paragraph.
Suggestion To Use Light-Emitting Diode
Another commenter agrees with the proposal but suggests that high-
intensity light-emitting diode (LED) lighting be used rather than
incandescent lighting. The commenter points out that LED lighting can
create a brighter light than that of incandescent lamps, but operate
cooler and more efficiently than halogen or incandescent lamps.
We partially agree with the commenter. We agree with the
commenter's assessment of LED technology; LED lighting has been found
to be cooler than halogen and brighter than incandescent lamps. We
disagree with any requirement to replace halogen lamps with LED
lighting. Although the new installation with incandescent lamps does
not provide as much light, the installation has been demonstrated and
inspected onboard the airplane and has been found to be compliant with
Federal Aviation Regulations. We will, however, consider specific
proposed alternative methods of compliance for the requirements of this
AD as specified in paragraph (h) of this AD. We have not changed the
final rule in this regard.
Request To Shorten Compliance Time
Another commenter requests that we reduce the compliance time to
less than the proposed 18 months. The commenter suggests the most
expeditious replacement schedule possible--as quickly as lamp suppliers
can provide the lamps, and the airplane operators can make the
replacements. The commenter suggests that the supplier can produce the
necessary number of lamps in a shorter time-frame than 18 months. The
commenter maintains that operators can replace the lamps without
waiting for scheduled maintenance, and that the work can be done during
several overnight maintenance actions.
We partially agree with the commenter. We agree with adhering to
the most expeditious replacement schedule that is reasonable. We strive
to review all risk collectively across the U.S. fleet, and then to
reduce that overall risk to acceptable levels. We disagree with a
compliance time of less than 18 months for this issue, because an 18-
month compliance time currently accomplishes a reduction to the risk of
another cargo fire at an accelerated, expeditious schedule. We have not
changed the final rule in this regard.
Request To Lengthen Compliance Time
Another commenter, the airplane manufacturer, requests that we
change the compliance time from 18 months to 36 months. The commenter
notes that 36 months is more appropriate and is conservative from a
risk-management standpoint. The commenter further states that a 36-
month compliance time would allow airplanes to accomplish the action on
the 133 affected U.S.-registered airplanes during regular scheduled
maintenance visits instead of requiring a potential unscheduled, and
therefore costly, maintenance task. The commenter points out that, in
accordance with Section 25.857 (``Cargo compartment classification'')
of the Federal Aviation Regulations (14 CFR 25.857(c)), the Model 777-
200 and 777-300 cargo compartments have smoke detection systems and an
approved built-in fire suppression system. The commenter states that
these systems would limit damage only to the cargo that initially
catches fire. The commenter also states that operators have been
notified to maintain clearance between cargo baggage and the ceiling
liner in the bulk compartment until the service bulletin is completed.
The commenter believes that, with a fleet history of over 7 million
flight hours and only one known cargo fire, the risk of an uncontrolled
cargo fire is extremely improbable.
We do not agree with the commenter. When we established the
compliance time of 18 months, we considered the urgency associated with
the unsafe condition, the availability of required parts, and the
practical aspects of replacing the lamps within a period or time that
corresponds to the normal maintenance schedules of most affected
operators. In addition, operators may request approval for an
alternative method of compliance according to paragraph (h) of this AD.
The request should include an assessment of the effect of the requested
change on the unsafe condition addressed by this AD. We have not
changed the final rule in this regard.
Request To Remove Manufacturer's Acknowledgement
The same commenter requests that we remove the sentence ``the
manufacturer has acknowledged this adjustment'' from the section in the
proposal titled ``Differences Between the Proposed AD and the Service
Bulletin'' in the preamble of the proposal. The commenter points out
that this statement implies that the manufacturer has agreed to the
shortened compliance time, when it has not agreed with this request.
We acknowledge the commenter's request but the ``Differences
Between the Proposed AD and the Service Bulletin'' section for the NPRM
is not reproduced in the final rule. Therefore, there is no change to
be made to the final rule. However clarification is necessary. The
statement quoted above is not intended to imply agreement on behalf of
the manufacturer. The statement is intended to clarify that we
contacted the manufacturer and alerted the appropriate individuals that
the compliance time in the proposal would differ from that in the
service bulletin. The manufacturer responded with a formal letter
acknowledging, and not necessarily agreeing with, the 18-month
compliance time.
Request To Include Additional Placard
Another commenter requests that the proposal require that operators
install a temporary placard stating that no cargo may be loaded against
the existing halogen light assemblies. The commenter states that this
placard would stay in place until the halogen lamps are replaced, and
would be a quick and easy way to alert operators of the halogen lamp
hazard.
We disagree with the request to include this additional placard.
Operators have already been warned of this hazard through a Boeing
Fleet Team Digest article, which was published in the first quarter of
2004. In addition, there are placards associated with the smoke
detection system ports in the ceiling cargo bay that caution not to
block the ports. Therefore, we have
[[Page 39641]]
determined that the intent of this comment is already satisfied. We
have not changed the final rule in this regard.
Explanation of Additional Change to Proposal
We have added a reference to Honeywell International Service
Bulletin 15-0712-33-0001, dated October 15, 2004, as an additional
source of service information for replacing the lamps. This reference
was inadvertently omitted from the proposal and is now included as Note
1 of the final rule.
Conclusion
We have carefully reviewed the available data, including the
comments that have been submitted, and determined that air safety and
the public interest require adopting the AD with the changes described
previously. We have determined that these changes will neither increase
the economic burden on any operator nor increase the scope of the AD.
Costs of Compliance
There are about 474 airplanes of the affected design in the
worldwide fleet. The following table provides the estimated costs for
U.S. operators to comply with this AD.
Estimated Costs
--------------------------------------------------------------------------------------------------------------------------------------------------------
Average
Airplane model Work hours hourly Parts Cost per Number of U.S.-registered Fleet cost
labor rate airplane airplanes
--------------------------------------------------------------------------------------------------------------------------------------------------------
777-200 (Group 1)........................ 5 $65 No cost to operators........ $325 133........................ $43,225
777-300 (Group 2)........................ 7 65 No cost to operators........ * 455 None currently............. * 0
--------------------------------------------------------------------------------------------------------------------------------------------------------
* The figures in this table would apply if an affected Model 777-300 series airplane is imported and placed on the U.S. Register in the future.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
subtitle VII, part A, subpart III, section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We have determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866;
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this AD. See the ADDRESSES section for a location to
examine the regulatory evaluation.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive (AD):
2005-14-04 Boeing: Amendment 39-14181. Docket No. FAA-2004-19795;
Directorate Identifier 2004-NM-196-AD.
Effective Date
(a) This AD becomes effective August 15, 2005.
Affected ADs
(b) None.
Applicability
(c) This AD applies to Boeing Model 777-200 and -300 series
airplanes, certificated in any category; as identified in Boeing
Special Attention Service Bulletin 777-33-0025, dated September 1,
2004.
Unsafe Condition
(d) This AD was prompted by a report of an aft cargo fire during
flight. We are issuing this AD to prevent a fire in the cargo
compartment.
Compliance
(e) You are responsible for having the actions required by this
AD performed within the compliance times specified, unless the
actions have already been done.
Lamp Replacement
(f) Within 18 months after the effective date of this AD,
replace all halogen lamps in the cargo compartment ceiling light
assemblies with new incandescent lamps that have the part number (P/
N) in paragraph (f)(1) of this AD or that meet the standard in
paragraph (f)(2) of this AD; and install warning and identification
placards. Except as provided by paragraph (f)(2) of this AD, do all
actions in accordance with the Accomplishment Instructions of Boeing
Special Attention Service Bulletin 777-33-0025, dated September 1,
2004.
(1) General Electric (P/N) GE2233 lamp, as referenced in Boeing
Special Attention Service Bulletin 777-33-0025, dated September 1,
2004.
(2) Any 28-volt incandescent lamp built to American National
Standards Institute (ANSI) 2233 specifications, and whose
manufacturer has requested and been assigned the ANSI 2233
designation by the American National Standards Institute.
Note 1: Boeing Special Attention Service Bulletin 777-33-0025,
dated September 1, 2004, refers to Honeywell International Service
Bulletin 15-0712-33-0001, dated October 15, 2004, as an additional
source of service information for replacing the lamps.
Parts Installation
(g) As of 18 months after the effective date of this AD, no
person may install a halogen bulb, P/N 9203 (Boeing), or P/N 55-
2181-7 (Honeywell), in any airplane cargo ceiling light assembly
(excluding the lamp in the airplane's bulk cargo door sill).
[[Page 39642]]
Alternative Methods of Compliance (AMOCs)
(h) The Manager, Seattle Aircraft Certification Office, FAA, has
the authority to approve AMOCs for this AD, if requested in
accordance with the procedures found in 14 CFR 39.19.
Material Incorporated by Reference
(i) You must use Boeing Special Attention Service Bulletin 777-
33-0025, dated September 1, 2004, to perform the actions that are
required by this AD, unless the AD specifies otherwise. The Director
of the Federal Register approves the incorporation by reference of
this document in accordance with 5 U.S.C. 552(a) and 1 CFR part 51.
For copies of the service information, contact Boeing Commercial
Airplanes, P.O. Box 3707, Seattle, Washington 98124-2207. For
information on the availability of this material at the National
Archives and Records Administration (NARA), call (202) 741-6030, or
go to http:// www.archives.gov/ federal--register/ code--of--
federal--regulations/ ibr--locations.html. You may view the AD
docket at the Docket Management Facility, U.S. Department of
Transportation, 400 Seventh Street SW., room PL-401, Nassif
Building, Washington, DC.
Issued in Renton, Washington, on June 24, 2005.
Michael J. Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 05-13140 Filed 7-8-05; 8:45 am]
BILLING CODE 4910-13-P