[Federal Register: January 12, 2005 (Volume 70, Number 8)]
[Proposed Rules]
[Page 2067-2070]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr12ja05-22]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2005-20025; Directorate Identifier 2004-NM-208-AD]
RIN 2120-AA64
Airworthiness Directives; Airbus Model A330, A340-200, and A340-
300 Series Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD)
for all Airbus Model A330, A340-200, and A340-300 series airplanes.
This proposed AD would require repetitive inspections of a certain
bracket that attaches the flight deck instrument panel to the airplane
structure, replacement of the bracket with a new, improved bracket, and
related investigative and corrective actions if necessary. This
proposed AD is prompted by reports of cracking of a certain bracket
that attaches the flight deck instrument panel to the airplane
structure. We are proposing this AD to detect and correct a cracked
bracket. Failure of this bracket, combined with failure of the
horizontal beam, could result in collapse of the left part of the
flight deck instrument panel, and consequent reduced controllability of
the airplane.
DATES: We must receive comments on this proposed AD by February 11,
2005.
ADDRESSES: Use one of the following addresses to submit comments on
this proposed AD.
DOT Docket Web site: Go to http://dms.dot.gov and follow
the instructions for sending your comments electronically.
Government-wide rulemaking Web site: Go to http://www.regulations.gov
and follow the instructions for sending your
comments electronically.
Mail: Docket Management Facility, U.S. Department of
Transportation, 400 Seventh Street, SW., Nassif Building, room PL-401,
Washington, DC 20590.
By fax: (202) 493-2251.
[[Page 2068]]
Hand Delivery: Room PL-401 on the plaza level of the
Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
For service information identified in this proposed AD, contact
Airbus, 1 Rond Point Maurice Belonte, 31707 Blagnac Cedex, France.
You can examine the contents of this AD docket on the Internet at
http://dms.dot.gov, or in person at the Docket Management Facility,
U.S. Department of Transportation, 400 Seventh Street, SW., room PL-
401, on the plaza level of the Nassif Building, Washington, DC. This
docket number is FAA-2005-20025; the directorate identifier for this
docket is 2004-NM-208-AD.
FOR FURTHER INFORMATION CONTACT: Tim Backman, Aerospace Engineer,
International Branch, ANM-116, FAA, Transport Airplane Directorate,
1601 Lind Avenue, SW., Renton, Washington 98055-4056; telephone (425)
227-2797; fax (425) 227-1149.
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to submit any relevant written data, views, or
arguments regarding this proposed AD. Send your comments to an address
listed under ADDRESSES. Include ``Docket No. FAA-2005-20025;
Directorate Identifier 2004-NM-208-AD'' at the beginning of your
comments. We specifically invite comments on the overall regulatory,
economic, environmental, and energy aspects of the proposed AD. We will
consider all comments submitted by the closing date and may amend the
proposed AD in light of those comments.
We will post all comments we receive, without change, to http://dms.dot.gov
, including any personal information you provide. We will
also post a report summarizing each substantive verbal contact with FAA
personnel concerning this proposed AD. Using the search function of our
docket Web site, anyone can find and read the comments in any of our
dockets, including the name of the individual who sent the comment (or
signed the comment on behalf of an association, business, labor union,
etc.) You can review the DOT's complete Privacy Act Statement in the
Federal Register published on April 11, 2000 (65 FR 19477-78), or you
can visit http://dms.dot.gov.
Examining the Docket
You can examine the AD docket on the Internet at http://dms.dot.go,
or in person at the Docket Management Facility office between 9 a.m.
and 5 p.m., Monday through Friday, except Federal holidays. The Docket
Management Facility office (telephone (800) 647-5227) is located on the
plaza level of the Nassif Building at the DOT street address stated in
the ADDRESSES section. Comments will be available in the AD docket
shortly after the DMS receives them.
Discussion
The Direction G[eacute]n[eacute]nrale de l'Aviation Civile (DGAC),
which is the airworthiness authority for France, notified us that an
unsafe condition may exist on all Airbus Model A330, A340-200, and
A340-300 series airplanes. The DGAC advises that a certain bracket, one
of eight parts that attaches the flight deck instrument panel to
airplane structure, has been found cracked on several airplanes. In one
case, the bracket was completely broken. The cracking has been
attributed to tightening of the bracket during assembly, combined with
further effects of differential pressure and flight loads. Failure of
the bracket cannot be detected without an inspection. If the horizontal
beam also fails, failure of this bracket could lead to collapse of the
left part of the flight deck instrument panel, and consequent reduced
controllability of the airplane.
Relevant Service Information
Airbus has issued Service Bulletins A330-25-3227 and A340-25-4230,
both including Appendix 01, both dated June 17, 2004. The service
bulletins describe procedures for performing repetitive detailed visual
inspections of a certain bracket that attaches the flight deck
instrument panel to airplane structure, and replacing the bracket with
a new, improved bracket if necessary. If both flanges of the bracket
are cracked, the service bulletin recommends contacting Airbus for
further action. The DGAC mandated the service information and issued
French airworthiness directives F-2004-140 and F-2004-141, both dated
August 18, 2004, to ensure the continued airworthiness of these
airplanes in France.
FAA's Determination and Requirement of the Proposed AD
These airplanes models are manufactured in France and are type
certificated for operation in the United States under the provisions of
Sec. 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and the
applicable bilateral airworthiness agreement. Pursuant to this
bilateral airworthiness agreement, the DGAC has kept the FAA informed
of the situation described above. We have examined the DGAC's findings,
evaluated all pertinent information, and determined that we need to
issue an AD for products of this type design that are certificated for
operation in the United States.
Therefore, we are proposing this AD, which would require
accomplishing the actions specified in the service information
described previously, except as discussed under ``Differences Among the
Proposed AD, the French Airworthiness Directives, and the Service
Information.'' The proposed AD would also require sending the
inspection results for any cracked bracket to Airbus.
Differences Among the Proposed AD, the French Airworthiness Directives,
and the Service Information
If you find both flanges of a subject bracket broken, the service
information and French airworthiness directives F-2004-140 and F-2004-
141 instruct you to contact Airbus. This proposed AD would require
that, if you find both flanges of a bracket broken, before further
flight, you replace the bracket and perform any applicable related
investigative and corrective actions in accordance with a method
approved by the FAA or the DGAC (or its delegated agent). These related
investigative and corrective actions may include inspections for damage
to surrounding structure caused by the broken bracket, and corrective
actions for any damage that is found.
For Model A330 series airplanes, Airbus Service Bulletins A330-25-
3227 and French airworthiness directive F-2004-140 specify an initial
inspection threshold of 16,500 total flight cycles. This proposed AD
would require you to perform the initial inspection prior to the
accumulation of 16,500 total flight cycles or within 60 days after the
effective date of the AD, whichever is later. We have included a 60-day
grace period to ensure that any airplane that is close to or has passed
the 16,500-total-flight-cycle threshold is not grounded as of the
effective date of the AD.
Clarification of Inspection Terminology
In this proposed AD, the ``detailed visual inspection'' specified
in the Airbus service bulletins is referred to as a ``detailed
inspection.'' We have included the definition for a detailed inspection
in a note in the proposed AD.
Interim Action
We consider this proposed AD interim action. If final action is
later identified, we may consider further rulemaking then.
[[Page 2069]]
Costs of Compliance
This proposed AD would affect about 19 Model A330 series airplanes
of U.S. registry. The proposed inspection would take about 1 work hour
per airplane, per inspection cycle, at an average labor rate of $65 per
work hour. Based on these figures, the estimated cost of the proposed
AD for U.S. operators is $1,235, or $65 per airplane, per inspection
cycle.
There are currently no affected Model A340-200 and -300 series
airplanes of U.S. registry. However, if one of these airplanes is
imported and put on the U.S. Register in the future, this cost estimate
will also apply to those airplanes.
Authority for This Rulemaking
The FAA's authority to issue rules regarding aviation safety is
found in Title 49 of the United States Code. Subtitle I Section 106,
describes the authority of the FAA Administrator. Subtitle VII,
Aviation Programs, describes in more detail the scope of the agency's
authority.
This rulemaking is promulgated under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, the FAA is charged with promoting
safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
proposed AD.
Regulatory Findings
We have determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify that the proposed
regulation:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this proposed AD. See the ADDRESSES section for a location
to examine the regulatory evaluation.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. The FAA amends Sec. 39.13 by adding the following new
airworthiness directive (AD):
Airbus: Docket No. FAA-2005-20025; Directorate Identifier 2004-NM-
208-AD.
Comments Due Date
(a) The Federal Aviation Administration must receive comments on
this AD action by February 11, 2005.
Affected ADs
(b) None.
Applicability
(c) This AD applies to all Airbus Model A330, A340-200, and
A340-300 series airplanes, certificated in any category.
Unsafe Condition
(d) This AD was prompted by reports of cracking of a certain
bracket that attaches the flight deck instrument panel to the
airplane structure. We are issuing this AD to detect and correct a
cracked bracket. Failure of this bracket, combined with failure of
the horizontal beam, could result in collapse of the left part of
the flight deck instrument panel, and consequent reduced
controllability of the airplane.
Compliance
(e) You are responsible for having the actions required by this
AD performed within the compliance times specified, unless the
actions have already been done.
Service Bulletin Reference
(f) The term ``service bulletin,'' as used in this AD, means the
Accomplishment Instructions of Airbus Service Bulletins A330-25-3227
(for Model A330 series airplanes) and A340-25-4230 (for Model A340-
200 and -300 series airplanes), both including Appendix 01, and both
dated June 17, 2004, as applicable.
Initial Inspection
(g) At the applicable time specified in paragraph (g)(1) or
(g)(2) of this AD, perform a detailed inspection of the bracket
having part number (P/N) F2511012920000, which attaches the flight
deck instrument panel to airplane structure, in accordance with the
service bulletin.
(1) For Model A330 series airplanes: Prior to the accumulation
of 16,500 total flight cycles, or within 60 days after the effective
date of this AD, whichever is later.
(2) For Model A340-200 and -300 series airplanes: Prior to the
accumulation of 9,700 total flight cycles, or within 2,700 flight
cycles after the effective date of this AD, whichever is later.
Note 1. For the purposes of this AD, a detailed inspection is:
``An intensive examination of a specific item, installation, or
assembly to detect damage, failure, or irregularity. Available
lighting is normally supplemented with a direct source of good
lighting at an intensity deemed appropriate. Inspection aids such as
mirror, magnifying lenses, etc., may be necessary. Surface cleaning
and elaborate procedures may be required.''
No Cracking/Repetitive Inspections
(h) If no cracking is found during the initial inspection
required by paragraph (g) of this AD: Repeat the inspection
thereafter at the applicable interval specified in paragraph (h)(1)
or (h)(2) of this AD.
(1) For Model A330 series airplanes: Intervals not to exceed
13,800 flight cycles.
(2) For Model A340-200 and -300 series airplanes: Intervals not
to exceed 7,000 flight cycles.
Crack Found/Replacement, Reporting, and Repetitive Inspections
(i) If any cracking is found during any inspection required by
paragraph (g) or (h) of this AD: Do the actions in paragraphs
(i)(1), (i)(2), and (i)(3) of this AD, except as provided by
paragraph (j) of this AD.
(1) Before further flight: Replace the cracked bracket with a
new, improved bracket having P/N F2511012920095, in accordance with
the service bulletin.
(2) Within 30 days after performing the inspection, or within 30
days after the effective date of this AD, whichever is later: Report
the cracked fitting to Airbus, Department AI/SE-A21, 1 Round Point
Maurice Bellonte, 31707 Blagnac Cedex, France. The report must
include the airplane serial number, the number of flight cycles and
flight hours on the airplane, the date of the inspection, and
whether both flanges of a bracket are broken. Submitting Appendix 01
of the applicable service bulletin is acceptable for compliance with
this paragraph. Under the provisions of the Paperwork Reduction Act
of 1980 (44 U.S.C. 3501 et seq.), the Office of Management and
Budget (OMB) has approved the information collection requirements
contained in this AD and has assigned OMB Control Number 2120-0056.
(3) Inspect the replaced bracket at the time specified in
paragraph (i)(3)(i) or (i)(3)(ii) of this AD. Then, do repetitive
inspections or replace the bracket as specified in paragraph (h) or
(i) of this AD, as applicable.
(i) For Model A330 series airplanes: Within 16,500 flight
cycles.
(ii) For Model A340-200 and -300 series airplanes: Within 9,700
flight cycles.
(j) If both flanges of a bracket are broken: Before further
flight, replace the bracket and
[[Page 2070]]
perform any applicable related investigative and corrective actions
(which may include inspections for damage to surrounding structure
caused by the broken bracket, and corrective actions for any damage
that is found), in accordance with a method approved by the Manager,
International Branch, ANM-116, Transport Airplane Directorate, FAA;
or the Direction Generale de l'Aviation Civile (DGAC) (or its
delegated agent).
Alternative Methods of Compliance (AMOCs)
(k) The Manager, International Branch, ANM-116, has the
authority to approve AMOCs for this AD, if requested in accordance
with the procedures found in 14 CFR 39.19.
Related Information
(l) French airworthiness directives F-2004-140 and F-2004-141,
both dated August 18, 2004, also address the subject of this AD.
Issued in Renton, Washington, on December 30, 2004.
Kevin M. Mullin,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 05-612 Filed 1-11-05; 8:45 am]
BILLING CODE 4910-13-M