[Federal Register: August 23, 2006 (Volume 71, Number 163)]
[Rules and Regulations]
[Page 49332-49335]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr23au06-5]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2006-24290; Directorate Identifier 2005-NM-243-AD;
Amendment 39-14731; AD 2006-17-10]
RIN 2120-AA64
Airworthiness Directives; Bombardier Model DHC-8-100, DHC-8-200,
and DHC-8-300 Series Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The FAA is adopting a new airworthiness directive (AD) for
certain Bombardier Model DHC-8-100, DHC-8-200, and DHC-8-300 series
airplanes. This AD requires repetitive inspections of the fluorescent
light tube assemblies of the cabin, lavatory, and sidewall, and
corrective actions if necessary. This AD also provides for optional
terminating action for the repetitive inspections. This AD results from
reports of overheating due to arcing between the fluorescent tube pins
and the lamp holder contacts. The tubes had not been properly seated
during installation. We are issuing this AD to prevent fumes, traces of
visible smoke, and fire at the fluorescent light tube assembly.
DATES: This AD becomes effective September 27, 2006.
The Director of the Federal Register approved the incorporation by
reference of certain publications listed in the AD as of September 27,
2006.
ADDRESSES: You may examine the AD docket on the Internet at http://dms.dot.gov
or in person at the Docket Management Facility, U.S.
Department of Transportation, 400 Seventh Street
[[Page 49333]]
SW., Nassif Building, Room PL-401, Washington, DC.
Contact Bombardier, Inc., Bombardier Regional Aircraft Division,
123 Garratt Boulevard, Downsview, Ontario M3K 1Y5, Canada, for service
information identified in this AD.
FOR FURTHER INFORMATION CONTACT: Douglas Wagner, Aerospace Engineer,
Systems and Flight Test Branch, ANE-172, FAA, New York Aircraft
Certification Office, 1600 Stewart Avenue, suite 410, Westbury, New
York 11590; telephone (516) 228-7306; fax (516) 794-5531.
SUPPLEMENTARY INFORMATION:
Examining the Docket
You may examine the airworthiness directive (AD) docket on the
Internet at http://dms.dot.gov or in person at the Docket Management
Facility office between 9 a.m. and 5 p.m., Monday through Friday,
except Federal holidays. The Docket Management Facility office
(telephone (800) 647-5227) is located on the plaza level of the Nassif
Building at the street address stated in the ADDRESSES section.
Discussion
The FAA issued a notice of proposed rulemaking (NPRM) to amend 14
CFR part 39 to include an AD that would apply to certain Bombardier
Model DHC-8-100, DHC-8-200, and DHC-8-300 series airplanes. That NPRM
was published in the Federal Register on April 4, 2006 (71 FR 16725).
That NPRM proposed to require repetitive inspections of the fluorescent
light tube assemblies of the cabin, lavatory, and sidewall, and
corrective actions if necessary. That NPRM also proposed to provide for
optional terminating action for the repetitive inspections.
Comments
We provided the public the opportunity to participate in the
development of this AD. We have considered the comments received.
Request To Extend Compliance Time
Piedmont Airlines states that its C-check inspection interval can
go up to 6,258 flight hours. Piedmont describes the grievous effect the
NPRM compliance times will have on the airline. The NPRM specifies a
compliance time of 5,000 flight hours or 36 months, whichever occurs
first, for the initial compliance time, and repetitive intervals of
5,000 flight hours. The commenter requests that the initial inspection
be done within the next C-check or 36 months and that the repetitive
interval be done at intervals not to exceed the next C-check.
We agree to extend the compliance time, although we cannot refer to
``the next C-check'' because the variability among operators'
maintenance schedules would not guarantee that the required work would
be done within an appropriate time. We have instead revised paragraph
(f) of this final rule to require an initial compliance time of 6,300
flight hours or 36 months, whichever occurs first, with a repetitive
interval of 6,300 flight hours. We have determined that such an
extension will not adversely affect safety, and will allow the work to
be performed during regularly scheduled maintenance at a base where
special equipment and trained maintenance personnel will be available
if necessary.
Request To Clarify Parts Replacement Requirements
Piedmont requests that we clarify paragraph (h) of the NPRM, which
prohibits installing a ballast part number (P/N) BA08006-1 or BA08006-
28-1 as of the effective date of the AD. Piedmont questions whether
that statement applies when parts are removed for other maintenance, or
only when the part is replaced.
We acknowledge the commenter's concern, but do not find it
necessary to revise the final rule. The intent of paragraph (h) is to
specifically prohibit replacing a ballast with another ballast having
P/N BA08006-1 or BA08006-28-1. By simply reinstalling a part removed
during maintenance, the operator is not ``installing'' a different
part.
Gaining access and installing that part for other maintenance
activities not associated with the AD is acceptable.
Additional Change to NPRM
Paragraph (f) of the NPRM refers to ``Chapter 33-20-00, Section
D,'' of the airplane maintenance manual (AMM) as one approved repair
method. We have removed the section reference (there is no Section D)
in this final rule. Acceptable repair instructions are found in Chapter
33-22-00 of the applicable AMM.
Conclusion
We have carefully reviewed the available data, including the
comments received, and determined that air safety and the public
interest require adopting the AD with the changes described previously.
We have determined that these changes will neither increase the
economic burden on any operator nor increase the scope of the AD.
Costs of Compliance
The following table provides the estimated costs for U.S. operators
to comply with this AD. This AD will affect about 121 U.S.-registered
airplanes.
Estimated Costs, Per Inspection Cycle
----------------------------------------------------------------------------------------------------------------
Average labor
Action Work hours rate per hour Parts Cost per airplane
----------------------------------------------------------------------------------------------------------------
Inspection, per inspection cycle. 6 maximum.......... $80 None............... Up to $480.
Ballast replacement (optional)... 2, per ballast \1\. 80 $486, per ballast.. Up to $41,344.
----------------------------------------------------------------------------------------------------------------
\1\Number of Ballasts Per Airplane
------------------------------------------------------------------------
Number of
Area Airplane model ballasts
------------------------------------------------------------------------
Lavatory......................... DHC-8-100 and -200...... 1
DHC-8-300............... 1
Sidewall......................... DHC-8-100 and -200...... 19
DHC-8-300............... 30
Cabin............................ DHC-8-100 and -200...... 21
DHC-8-300............... 33
------------------------------------------------------------------------
[[Page 49334]]
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We have determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866;
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this AD and placed it in the AD docket. See the ADDRESSES
section for a location to examine the regulatory evaluation.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
0
Accordingly, under the authority delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority : 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The Federal Aviation Administration (FAA) amends Sec. 39.13 by
adding the following new airworthiness directive (AD):
2006-17-10 BOMBARDIER, INC. (Formerly de Havilland, Inc.): Amendment
39-14731. Docket No. FAA-2006-24290; Directorate Identifier 2005-NM-
243-AD.
Effective Date
(a) This AD becomes effective September 27, 2006.
Affected ADs
(b) None.
Applicability
(c) This AD applies to Bombardier Model DHC-8-102, -103, -106, -
201, -202, -301, -311, and -315 airplanes; certificated in any
category; serial numbers 003 through 407 inclusive, 409 through 412
inclusive, and 414 through 433 inclusive; excluding those with
Hunting interiors.
Unsafe Condition
(d) This AD results from reports of overheating due to arcing
between the fluorescent tube pins and the lamp holder contacts. The
tubes had not been properly seated during installation. We are
issuing this AD to prevent fumes, traces of visible smoke, and fire
at the fluorescent light tube assembly.
Compliance
(e) You are responsible for having the actions required by this
AD performed within the compliance times specified, unless the
actions have already been done.
Inspection
(f) Within 6,300 flight hours or 36 months after the effective
date of this AD, whichever occurs first: Perform detailed
inspections to detect signs of arcing of the fluorescent tube
assemblies of the cabin, sidewalls, and lavatory, in accordance with
the applicable temporary revision (TR) of the applicable maintenance
program manual (MPM) identified in Table 1 of this AD. If any sign
of arcing is found, repair before further flight using a method
approved by either the Manager, New York Aircraft Certification
Office (ACO), FAA; or Transport Canada Civil Aviation (or its
delegated agent). Chapter 33-20-00 of the applicable airplane
maintenance manual is one approved method. Repeat the inspection at
intervals not to exceed 6,300 flight hours, until all ballast part
numbers (P/Ns) BA08006-1 or BA08006-28-1 have been replaced in
accordance with paragraph (g) of this AD.
Table 1.--TRs
----------------------------------------------------------------------------------------------------------------
In
Inspect the fluorescent tube accordance To the de Havilland
assemblies of the-- with task-- of de Havilland TR-- DASH 8 series-- For model--
----------------------------------------------------------------------------------------------------------------
Cabin............................. 3320/01 MRB-146, dated 100 MPM PSM 1-8-7... DHC-8-102, -103, and
August 31, 2004. -106 airplanes.
3320/01 MRB 2-24, dated 200 MPM PSM 1-82-7.. DHC-8-201 and -202
August 31, 2004. airplanes.
3320/01 MRB 3-155, dated 300 MPM PSM 1-83-7.. DHC-8-301, -311, and
August 31, 2004. -315 airplanes.
Lavatory.......................... 3320/03 MRB-147, dated May 100 MPM PSM 1-8-7... DHC-8-102, -103, -
3, 2005. 106 airplanes.
3320/03 MRB 2-25, dated May 200 MPM PSM 1-82-7.. DHC-8-201 and -202
3, 2005. airplanes.
3320/03 MRB 3-156, dated May 300 MPM PSM 1-83-7.. DHC-8-301, -311, and
3, 2005. -315 airplanes.
Sidewall.......................... 3320/02 MRB-147, dated May 100 MPM PSM 1-8-7... DHC-8-102, -103, and
3, 2005. -106 airplanes.
3320/02 MRB 2-25, dated May 200 MPM PSM 1-82-7.. DHC-8-201 and -202
3, 2005. airplanes.
3320/02 MRB 3-156, dated May 300 MPM PSM 1-83-7.. DHC-8-301, -311, and
3, 2005. -315 airplanes.
----------------------------------------------------------------------------------------------------------------
[[Page 49335]]
Note 1: For the purposes of this AD, a detailed inspection is:
``An intensive examination of a specific item, installation, or
assembly to detect damage, failure, or irregularity. Available
lighting is normally supplemented with a direct source of good
lighting at an intensity deemed appropriate. Inspection aids such as
mirror, magnifying lenses, etc., may be necessary. Surface cleaning
and elaborate procedures may be required.''
Terminating Action
(g) The repetitive inspections required by this AD may be
terminated if all ballasts installed on the airplane have P/N
BR9000-21, installed in accordance with the Accomplishment
Instructions of Bombardier Service Bulletin 8-33-51, Revision `A,'
dated April 20, 2005 (to replace ballast P/N BA08006-1), or 8-33-52,
dated April 15, 2005 (to replace ballast P/N BA08006-28-1). Ballasts
installed before the effective date of this AD are also acceptable
if done in accordance with Bombardier Service Bulletin 8-33-51,
dated August 16, 2002.
Parts Installation
(h) As of the effective date of this AD: No person may install a
ballast P/N BA08006-1 or BA08006-28-1 on any airplane.
Alternative Methods of Compliance (AMOCs)
(i)(1) The Manager, New York ACO, FAA, has the authority to
approve AMOCs for this AD, if requested in accordance with the
procedures found in 14 CFR 39.19.
(2) Before using any AMOC approved in accordance with Sec.
39.19 on any airplane to which the AMOC applies, notify the
appropriate principal inspector in the FAA Flight Standards
Certificate Holding District Office.
Related Information
(j) Canadian airworthiness directive CF-2004-26R1, dated
September 28, 2005, also addresses the subject of this AD.
Material Incorporated by Reference
(k) You must use the service information identified in Table 2
of this AD to perform the actions that are required by this AD,
unless the AD specifies otherwise.
Table 2.--Material Incorporated by Reference
------------------------------------------------------------------------
To the de Havilland DASH 8
de Havilland Temporary Revision-- Series--
------------------------------------------------------------------------
MRB-146, dated August 31, 2004......... 100 Maintenance Program Manual
PSM 1-8-7.
MRB-147, dated May 3, 2005............. 100 Maintenance Program Manual
PSM 1-8-7.
MRB 2-24, dated August 31, 2004........ 200 Maintenance Program Manual
PSM 1-82-7.
MRB 2-25, dated May 3, 2005............ 200 Maintenance Program Manual
PSM 1-82-7.
MRB 3-155, dated August 31, 2004....... 300 Maintenance Program Manual
PSM 1-83-7.
MRB 3-156, dated May 3, 2005........... 300 Maintenance Program Manual
PSM 1-83-7.
------------------------------------------------------------------------
(Page 2 of de Havilland Temporary Revision MRB-147, dated May 3,
2005, incorrectly refers to Series 300 airplanes; that reference
should be to Series 100.) If the terminating action is accomplished,
you must use Bombardier Service Bulletin 8-33-51, Revision `A,'
dated April 20, 2005; or Bombardier Service Bulletin 8-33-52, dated
April 15, 2005, as applicable, to perform the optional terminating
action specified in this AD. The Director of the Federal Register
approved the incorporation by reference of these documents in
accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Contact
Bombardier, Inc., Bombardier Regional Aircraft Division, 123 Garratt
Boulevard, Downsview, Ontario M3K 1Y5, Canada, for a copy of this
service information. You may review copies at the Docket Management
Facility, U.S. Department of Transportation, 400 Seventh Street,
SW., Room PL-401, Nassif Building, Washington, DC; on the Internet
at http://dms.dot.gov; or at the National Archives and Records
Administration (NARA). For information on the availability of this
material at the NARA, call (202) 741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html
.
Issued in Renton, Washington, on August 14, 2006.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E6-13829 Filed 8-22-06; 8:45 am]
BILLING CODE 4910-13-P