[Federal Register: November 6, 2006 (Volume 71, Number 214)]
[Rules and Regulations]
[Page 64884-64887]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr06no06-2]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2006-23921; Directorate Identifier 2005-NM-205-AD;
Amendment 39-14812; AD 2006-22-15]
RIN 2120-AA64
Airworthiness Directives; Boeing Model 747 Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The FAA is superseding an existing airworthiness directive
(AD), which applies to all Boeing Model 747 series airplanes. That AD
currently requires repetitive inspections for cracking of the top and
side panel webs and panel stiffeners of the nose wheel well (NWW), and
corrective actions if necessary. This new AD reduces the interval for
certain repetitive inspections and removes a certain optional
inspection. This new AD also requires replacing the NWW side and top
panels with new panels, which terminates the repetitive inspections.
This AD results from the development of a new modification. We are
issuing this AD to prevent fatigue cracks in the top and side panel
webs and stiffeners of the NWW, which could compromise the structural
integrity of the NWW and could lead to the rapid decompression of the
airplane.
DATES: This AD becomes effective December 11, 2006.
The Director of the Federal Register approved the incorporation by
reference of a certain publication listed in the AD as of December 11,
2006.
On May 10, 2005 (70 FR 21141, April 25, 2005), the Director of the
Federal Register approved the incorporation by reference of Boeing
Alert Service Bulletin 747-53A2465, Revision 4, dated February 24,
2005.
ADDRESSES: You may examine the AD docket on the Internet at http://dms.dot.gov
or in person at the Docket Management Facility, U.S.
Department of Transportation, 400 Seventh Street, SW., Nassif Building,
Room PL-401, Washington, DC.
Contact Boeing Commercial Airplanes, P.O. Box 3707, Seattle,
Washington 98124-2207, for service information identified in this AD.
FOR FURTHER INFORMATION CONTACT: Nick Kusz, Airframe Branch, ANM-120S,
FAA, Seattle Aircraft Certification Office, 1601 Lind Avenue, SW.,
Renton, Washington 98057-3356; telephone (425) 917-6432; fax (425) 917-
6590.
SUPPLEMENTARY INFORMATION:
Examining the Docket
You may examine the airworthiness directive (AD) docket on the
Internet at http://dms.dot.gov or in person at the Docket Management
Facility office between 9 a.m. and 5 p.m., Monday through Friday,
except Federal holidays. The Docket Management Facility office
(telephone (800) 647-5227) is located on the plaza level of the Nassif
Building at the street address stated in the ADDRESSES section.
Discussion
The FAA issued a notice of proposed rulemaking (NPRM) to amend 14
CFR part 39 to include an AD that supersedes AD 2005-09-02, amendment
39-14070 (70 FR 21141, April 25, 2005). [A correction of that AD was
published in the Federal Register on May 25, 2005 (70 FR 29940).] The
existing AD applies to all Boeing Model 747 series airplanes. That NPRM
was published in the Federal Register on February 15, 2006 (71 FR
7883). That NPRM proposed to continue to require repetitive inspections
for cracking of the top and side panel webs and panel stiffeners of the
nose wheel well (NWW), and corrective actions if necessary. That NPRM
also proposed to reduce the interval for certain repetitive inspections
and remove a certain optional inspection. That NPRM also proposed to
require replacing the NWW side and top panels with new panels, which
would terminate the repetitive inspections.
Comments
We provided the public the opportunity to participate in the
development of this AD. We have considered the comments that have been
received on the NPRM.
Support for the NPRM
Boeing, the airplane manufacturer, agrees with the contents of the
NPRM.
Request To Remove Actions for Group 2 Airplanes or Extend Compliance
Time
The Air Transport Association (ATA), on behalf of one of its
members, Northwest Airlines (NWA), requests that either the proposed
requirement for terminating action for Group 2 airplanes be removed
from the NPRM or the compliance time for doing the termination action
be extended from four years to six years. The ATA notes that there are
no service instructions for the terminating action for Group 2
airplanes. The ATA also states that extending the compliance time will
allow the development of the service instructions and an assessment of
the requirement's impact. NWA adds that it has not experienced
extensive cracking that would warrant serious consideration or
justification to mandate the terminating action (replacement of the NWW
side and top panels). NWA also states that it would be very difficult
to accomplish the replacement without a service bulletin.
We agree with the commenter's concern regarding lack of
availability of service instructions for Group 2 airplanes; however, we
do not consider that removing the terminating action or delaying this
action until after the
[[Page 64885]]
manufacturer develops a service bulletin for the replacement of the NWW
side and top panels for Group 2 airplanes is warranted.
We have coordinated with Boeing regarding the availability of
service instructions. Boeing states that it will issue a revised
service bulletin that includes procedures for Group 2 airplanes by July
2007 and that there will parts available at that time. Therefore, we
have revised the compliance time for Group 2 airplanes to allow
adequate time to accomplish the actions specified in this final rule.
We have extended the compliance time specified in paragraph (o) of
the final rule from 48 months to 57 months. We have determined that
extending the compliance time will not adversely affect safety. In
addition, under the provisions of paragraph (p) of the final rule, we
may approve requests for adjustments to the compliance time if data are
submitted to substantiate that such an adjustment would provide an
acceptable level of safety.
Explanation of Change Made to NPRM
For clarification, the FAA has revised the definition of a
``detailed inspection'' in Note 1 of this final rule.
Typographical Errors
The date of Revision 4 of Boeing Alert Service Bulletin 747-53A2465
was inadvertently specified as ``February 25'' instead of ``February
24'' in paragraph (f) and Table 1 of the NPRM. We have revised this
final rule accordingly.
The Federal Register number and date of the existing AD was
inadvertently specified as ``70 FR 29940, May 25, 2005'' in paragraph
2. of the NPRM. The existing AD was published April 25, 2005 (70 FR
21141). A correction of the existing AD was published May 25, 2005 (70
FR 29940). We have revised this final rule accordingly.
Conclusion
We have carefully reviewed the available data, including the
comments that have been received, and determined that air safety and
the public interest require adopting the AD with the changes described
previously. We have determined that these changes will neither increase
the economic burden on any operator nor increase the scope of the AD.
Costs of Compliance
There are about 1,127 airplanes of the affected design in the
worldwide fleet. The following table provides the estimated costs for
U.S. operators to comply with this AD. Work hours are estimated at an
average labor rate of $65 per work hour.
Estimated Costs
----------------------------------------------------------------------------------------------------------------
Number of U.S.-
Action Work hours Parts Cost per registered Fleet cost
airplane airplanes
----------------------------------------------------------------------------------------------------------------
Area 1 and 3 inspections 79 $0 $5,135, per 255 $1,309,425, per
(required by AD 2005-09-02). inspection inspection
cycle. cycle.
Area 2 inspections (required 8-18 0 $520-$1,170, per 255 Up to $298,350,
by AD 2005-09-02). inspection per inspection
cycle. cycle.
Replacement (new action)..... 800 115,765 $167,765........ 255 $42,780,075.
----------------------------------------------------------------------------------------------------------------
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
subtitle VII, part A, subpart III, section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We have determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866;
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this AD and placed it in the AD docket. See the ADDRESSES
section for a location to examine the regulatory evaluation.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
0
Accordingly, under the authority delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The Federal Aviation Administration (FAA) amends Sec. 39.13 by
removing amendment 39-14070 (70 FR 21141, April 25, 2005), corrected at
70 FR 29940, May 25, 2005, and by adding the following new
airworthiness directive (AD):
2006-22-15 Boeing: Amendment 39-14812. Docket No. FAA-2006-23921;
Directorate Identifier 2005-NM-205-AD.
Effective Date
(a) This AD becomes effective December 11, 2006.
Affected ADs
(b) This AD supersedes AD 2005-09-02.
Applicability
(c) This AD applies to all Boeing Model 747-100, 747-100B, 747-
100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D,
747-400F, 747SR, and 747SP series airplanes, certificated in any
category.
[[Page 64886]]
Unsafe Condition
(d) This AD results from the development of a new modification.
We are issuing this AD to prevent fatigue cracks in the top and side
panel webs and stiffeners of the nose wheel well (NWW), which could
compromise the structural integrity of the NWW and lead to the rapid
decompression of the airplane.
Compliance
(e) You are responsible for having the actions required by this
AD performed within the compliance times specified, unless the
actions have already been done.
Restatement of Requirements of AD 2005-09-02 With New Repetitive
Interval and Service Information
Initial and Repetitive Inspections of the Top and Side Panel
Stiffeners
(f) Prior to the accumulation of 16,000 total flight cycles, or
within 1,000 flight cycles after January 27, 2005 (the effective
date of AD 2004-25-23, amendment 39-13911), whichever is later, do
internal detailed and surface high frequency eddy current (HFEC)
inspections of the top and side panel stiffeners of the NWW
(specified as Area 3 in the service bulletin) for cracks in
accordance with the Accomplishment Instructions of Boeing Alert
Service Bulletin (ASB) 747-53A2465, Revision 4, dated February 24,
2005. Repeat the inspections thereafter at the compliance times
specified in paragraph (f)(1) or (f)(2) of this AD, as applicable.
(1) For airplanes on which an inspection has not been done
before the effective date of this AD in accordance with any service
bulletin listed in Table 1 of this AD: Within 1,500 flight cycles
after doing the inspection specified in paragraph (f) of this AD,
repeat the inspection. Repeat the inspection thereafter at intervals
not to exceed 1,500 flight cycles.
(2) For airplanes on which an inspection has been done before
the effective date of this AD in accordance with any service
bulletin listed in Table 1 of this AD: Within 6,000 flight cycles
after doing the inspection specified in paragraph (f) of this AD or
within 1,500 flight cycles after the effective date of this AD,
whichever occurs first, repeat the inspection. Repeat the inspection
thereafter at intervals not to exceed 1,500 flight cycles.
Table 1.--Boeing Service Bulletins
----------------------------------------------------------------------------------------------------------------
Service bulletin Revision level Date
----------------------------------------------------------------------------------------------------------------
Boeing ASB 747-53A2465................ Original........................... April 5, 2001.
Boeing ASB 747-53A2465................ 2.................................. November 11, 2004.
Boeing ASB 747-53A2465................ 3.................................. December 23, 2004.
Boeing ASB 747-53A2465................ 4.................................. February 24, 2005.
Boeing Service Bulletin 747-53A2465... 1.................................. October 16, 2003.
----------------------------------------------------------------------------------------------------------------
Note 1: For the purposes of this AD, a detailed inspection is:
``An intensive examination of a specific item, installation, or
assembly to detect damage, failure, or irregularity. Available
lighting is normally supplemented with a direct source of good
lighting at an intensity deemed appropriate. Inspection aids such as
mirror, magnifying lenses, etc., may be necessary. Surface cleaning
and elaborate procedures may be required.''
Initial Inspections of the Top and Sidewall Panel Webs
(g) Do an external detailed inspection of the top and sidewall
panel webs of the NWW (specified as Area 1 and Area 2 in the service
bulletin) for cracks, in accordance with the Accomplishment
Instructions of Boeing ASB 747-53A2465, Revision 4, dated February
24, 2005, at the earlier of the times specified in paragraphs (g)(1)
and (g)(2) of this AD.
(1) At the later of the times specified in paragraph (g)(1)(i)
and (g)(1)(ii) of this AD:
(i) Before accumulating 20,000 total flight cycles.
(ii) Within 100 flight cycles or 90 days after May 10, 2005 (the
effective date of AD 2005-09-02), whichever occurs first.
(2) At the later of the times specified in paragraphs (g)(2)(i)
and (g)(2)(ii) of this AD:
(i) Before accumulating 16,000 total flight cycles.
(ii) Within 1,000 flight cycles after May 10, 2005.
Repetitive Inspections of the Top and Sidewall Panel Webs
(h) Repeat the inspection required by paragraph (g) of this AD
at the intervals specified in paragraphs (h)(1) and (h)(2) of this
AD, as applicable.
(1) For airplanes with fewer than 20,000 total flight cycles as
of May 10, 2005, repeat at intervals not to exceed 1,000 flight
cycles until the first inspection after the airplane reaches 20,000
total flight cycles.
(2) For airplanes with 20,000 total flight cycles or more,
repeat at intervals not to exceed 500 flight cycles.
Ultrasonic (UT) Inspections
(i) Do an UT inspection of the top and sidewall panel webs for
cracks, in accordance with Boeing ASB 747-53A2465, Revision 4, dated
February 24, 2005, at the later of the times specified in paragraphs
(i)(1) and (i)(2) of this AD. Repeat the inspections thereafter at
intervals not to exceed 500 flight cycles.
(1) Prior to the accumulation of 20,000 total flight cycles.
(2) Within 100 flight cycles or 90 days after May 10, 2005,
whichever occurs first.
Additional Inspections and Corrective Actions
(j) Except as specified in paragraph (l) of this AD, if any
crack is found during any inspection required by this AD, prior to
further flight, do any applicable additional detailed inspections of
stiffeners and beams and make repairs, in accordance with the
Accomplishment Instructions of Boeing ASB 747-53A2465, Revision 4,
dated February 24, 2005.
Actions Accomplished per Previous Issues of Service Bulletin
(k) The actions specified in paragraphs (k)(1), (k)(2), and
(k)(3) of this AD are acceptable for compliance with the
corresponding action specified in the applicable paragraph.
(1) Inspections and corrective actions accomplished before
January 27, 2005, in accordance with Boeing ASB 747-53A2465, dated
April 5, 2001, are considered acceptable for compliance with the
corresponding inspections specified in paragraph (f) of this AD.
(2) Inspections accomplished before the effective date of this
AD, in accordance with Boeing Service Bulletin 747-53A2465, Revision
1, dated October 16, 2003; Boeing ASB 747-53A2465, Revision 2, dated
November 11, 2004; and Boeing ASB 747-53A2465, Revision 3, dated
December 23, 2004; are considered acceptable for compliance with the
corresponding inspections specified in paragraph (f) of this AD.
Note 2: The detailed and surface HFEC inspections of the top and
side panel stiffeners of the NWW specified in Boeing ASB 747-
53A2465, dated April 5, 2001; and Boeing Service Bulletin 747-
53A2465, Revision 1, dated October 16, 2003; are acceptable for
compliance with the internal detailed and surface HFEC inspections
specified in paragraph (f) of this AD.
(3) Inspections and corrective actions accomplished before May
10, 2005, in accordance with Boeing Service Bulletin 747-53A2465,
Revision 1, dated October 16, 2003; Boeing ASB 747-53A2465, Revision
2, dated November 11, 2004; and Boeing ASB 747-53A2465, Revision 3,
dated December 23, 2004; are considered acceptable for compliance
with the corresponding inspections specified in paragraphs (g) and
(h) of this AD.
Certain Other Corrective Actions
(l) Where Boeing Service Bulletin and ASB 747-53A2465 specify
contacting the manufacturer if certain cracking is found, this AD
requires, before further flight,
[[Page 64887]]
repairing the cracking using a method approved in accordance with
the procedures specified in paragraph (p) of this AD.
No Reporting Requirement
(m) Although Boeing Service Bulletin and ASB 747-53A2465 specify
that operators should report inspection results to the manufacturer,
this AD does not require those inspection results to be reported.
New Requirements of This AD
Terminating Action
(n) For Group 1 and 3 airplanes identified in Boeing Service
Bulletin 747-53A2562, Revision 1, dated July 28, 2005: Before
accumulating 22,000 total flight cycles or within 48 months after
the effective date of this AD, whichever occurs later, replace the
NWW side and top panels with new panels in accordance with the
Accomplishment Instructions of Boeing Service Bulletin 747-53A2562,
Revision 1, dated July 28, 2005. Doing the replacement terminates
the requirements of this AD.
(o) For Group 2 airplanes identified in Boeing Service Bulletin
747-53A2562, Revision 1, dated July 28, 2005, and Model 747
airplanes not identified in the service bulletin: Before
accumulating 22,000 total flight cycles or within 57 months after
the effective date of this AD, whichever occurs later, replace the
NWW side and top panels using a method approved by the Manager,
Seattle Aircraft Certification Office (ACO), FAA. Doing the
replacement terminates the requirements of this AD.
Alternative Methods of Compliance (AMOCs)
(p)(1) The Manager, Seattle ACO, FAA, has the authority to
approve AMOCs for this AD, if requested in accordance with the
procedures found in 14 CFR 39.19.
(2) Before using any AMOC approved in accordance with Sec.
39.19 on any airplane to which the AMOC applies, notify the
appropriate principal inspector in the FAA Flight Standards
Certificate Holding District Office.
(3) An AMOC that provides an acceptable level of safety may be
used for any repair required by this AD, if it is approved by an
Authorized Representative for the Boeing Commercial Airplanes
Delegation Option Authorization Organization who has been authorized
by the Manager, Seattle ACO, to make those findings. For a repair
method to be approved, the repair must meet the certification basis
of the airplane.
(4) AMOCs approved previously according to AD 2005-09-02 are
approved as AMOCs for the corresponding provisions of paragraphs (f)
through (j) and (l) of this AD.
(5) AMOCs approved previously according to AD 2004-25-23 are
approved as AMOCs for the corresponding provisions of paragraph (f)
of this AD.
Material Incorporated by Reference
(q) You must use Boeing Alert Service Bulletin 747-53A2465,
Revision 4, dated February 24, 2005; and Boeing Service Bulletin
747-53A2562, Revision 1, dated July 28, 2005; as applicable, to
perform the actions that are required by this AD, unless the AD
specifies otherwise.
(1) The Director of the Federal Register approved the
incorporation by reference of Boeing Service Bulletin 747-53A2562,
Revision 1, dated July 28, 2005, in accordance with 5 U.S.C. 552(a)
and 1 CFR part 51.
(2) On May 10, 2005 (70 FR 21141, April 25, 2005), the Director
of the Federal Register approved the incorporation by reference of
Boeing Alert Service Bulletin 747-53A2465, Revision 4, dated
February 24, 2005.
(3) Contact Boeing Commercial Airplanes, P.O. Box 3707, Seattle,
WA 98124-2207, for a copy of this service information. You may
review copies at the Docket Management Facility, U.S. Department of
Transportation, 400 Seventh Street, SW., Room PL-401, Nassif
Building, Washington, DC; on the Internet at http://dms.dot.gov; or
at the National Archives and Records Administration (NARA). For
information on the availability of this material at the NARA, call
(202) 741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html
.
Issued in Renton, Washington, on October 25, 2006.
Kalene C. Yanamura,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E6-18465 Filed 11-3-06; 8:45 am]
BILLING CODE 4910-13-P