[Federal Register: January 25, 2006 (Volume 71, Number 16)]
[Proposed Rules]
[Page 4072-4075]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr25ja06-24]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2006-23578; Directorate Identifier 2006-CE-01-AD]
RIN 2120-AA64
Airworthiness Directives; Mitsubishi Heavy Industries MU-2B
Series Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: The FAA proposes to adopt a new airworthiness directive (AD)
for all Mitsubishi Heavy Industries (MHI) MU-2B series airplanes. This
proposed AD would require you to do the following: Remove and visually
inspect the wing attach barrel nuts, bolts, and retainers for cracks,
corrosion, and fractures; replace any cracked, corroded, or fractured
parts; inspect reusable barrel nuts and bolts for deformation and
irregularities in the threads; replace any deformed or irregular parts;
and install new or reusable parts and torque to the correct value. This
proposed AD results from a recent safety evaluation that used a data-
driven approach to evaluate the design, operation, and maintenance of
the MU-2B series airplanes in order to determine their safety and
define what steps, if any, are necessary to ensure their safe
operation. Part of that evaluation was the identification of unsafe
conditions that exist or could develop on the affected type design
airplanes. We are issuing this proposed AD to detect and correct
cracks, corrosion, fractures, and incorrect torque values in the wing
attach barrel nuts, which could result in failure of the wing barrel
nuts and/or associated wing attachment hardware. This failure could
lead to in-flight separation of the outer wing from the center wing
section and result in loss of controlled flight.
DATES: We must receive comments on this proposed AD by February 27,
2006.
ADDRESSES: Use one of the following addresses to comment on this
proposed AD:
DOT Docket Web site: Go to http://dms.dot.gov and follow
the instructions for sending your comments electronically.
Government-wide rulemaking Web site: Go to http://www.regulations.gov
and follow the instructions for sending your
comments electronically.
Mail: Docket Management Facility; U.S. Department of
Transportation, 400 Seventh Street, SW., Nassif Building, Room PL-401,
Washington, DC 20590.
Fax: 1-202-493-2251.
Hand Delivery: Room PL-401 on the plaza level of the
Nassif Building, 400 Seventh Street, SW., Washington, DC, between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
Contact Mitsubishi Heavy Industries, Ltd., Nagoya Aerospace Systems
Works, 10, OYE-CHO, Minato-Ku, Nagoya, Japan, or Turbine Aircraft
Services, Inc., 4550 Jimmy Doolittle Drive, Addison, Texas 75001;
telephone: (972) 248-3108; facsimile: (972) 248-3321, for the service
information identified in this proposed AD.
You may examine the comments on this proposed AD in the AD docket
on the Internet at http://dms.dot.gov.
FOR FURTHER INFORMATION CONTACT: Andrew McAnaul, Aerospace Engineer,
ASW-150 (c/o MIDO-43), 10100 Reunion Place, Suite 650, San Antonio,
Texas 78216; telephone: (210) 308-3365; facsimile: (210) 308-3370.
SUPPLEMENTARY INFORMATION:
Comments Invited
How do I comment on this proposed AD? We invite you to send any
written relevant data, views, or arguments regarding this proposal.
Send your comments to an address listed under ADDRESSES. Include the
docket number, ``FAA-2006-23578; Directorate Identifier 2006-CE-01-AD''
at the beginning of your comments. We specifically invite comments on
the overall regulatory, economic, environmental, and energy aspects of
the proposed AD. We will consider all comments received by the closing
date and may amend the proposed AD in light of those comments.
We will post all comments we receive, without change, to http://dms.dot.gov
, including any personal information you provide. We will
also post a report summarizing each substantive verbal contact with FAA
personnel concerning this proposed rulemaking. Using the search
function of the DOT docket web site, anyone can find and read the
comments received into any of our dockets, including the name of the
individual who sent the comment (or signed the comment on behalf of an
association, business, labor union, etc.). You may review the DOT's
complete Privacy Act Statement in the Federal Register published on
April 11, 2000 (65 FR 19477-78) or you may visit http://dms.dot.gov.
Examining the Dockets
Where can I go to view the docket information? You may examine the
docket that contains the proposal, any comments received and any final
disposition on the Internet at http://dms.dot.gov, or in person at the
DOT Docket Offices between 9 a.m. and 5 p.m., Monday through Friday,
except Federal holidays. The Docket Office (telephone 1-800-647-5227)
is located on the plaza level of the Department of Transportation
NASSIF Building at the street address stated in ADDRESSES. Comments
will be available in the AD docket shortly after the Docket Management
Facility receives them.
Discussion
What events have caused this proposed AD? Recent accidents and the
service history of the Mitsubishi MU-2B series airplanes prompted FAA
to conduct an MU-2B Safety Evaluation. This evaluation used a data-
driven approach to evaluate the design, operation, and maintenance of
MU-2B series airplanes in order to determine their safety and define
what steps, if any, are necessary to ensure their safe operation.
The safety evaluation provided an in-depth review and analysis of
MU-2B incidents, accidents, safety data, pilot training requirements,
engine reliability, and commercial operations. In conducting this
evaluation, the team employed new analysis tools that provided a much
more detailed root cause analysis of the MU-2B problems than was
previously possible.
Part of that evaluation was to identify unsafe conditions that
exist or could develop on the affected type design airplanes. One of
these conditions is the discovery of the right wing upper forward and
lower forward barrel nuts found cracked during a scheduled 7,500-hour
inspection on one of the affected airplanes. The manufacturer conducted
additional investigations of the barrel nuts on other affected
airplanes. The result of this investigation revealed no other cracked
barrel nuts. However, it was discovered that several airplanes had
over-torqued barrel nuts, which could result in cracking.
[[Page 4073]]
What is the potential impact if FAA took no action? This condition,
if not detected and corrected, could result in failure of the wing
barrel nuts and/or associated wing attachment hardware. This failure
could lead to in-flight separation of the outer wing from the center
wing section and result in loss of controlled flight.
Relevant Service Information
Is there service information that applies to this subject? We have
reviewed Mitsubishi Heavy Industries, Ltd. MU-2 Service Bulletin
referenced as JCAB T.C.: No. 241, dated July 14, 2004, and MU-2 Service
Bulletin referenced as FAA T.C.: No. 103/57-004, dated August 2, 2004.
What are the provisions of this service information? These service
bulletins describe procedures for:
Removing and inspecting the wing attach barrel nuts and
retainer for cracks, corrosion, and fractures;
Replacing any wing attach barrel nuts and retainer with
cracks, corrosion, or fractures;
Inspecting any bolts or barrel nuts to be reused for
deformation or irregularities in the threads;
Replacing any bolts or barrel nuts with deformation or
irregularities in the threads; and
Reinstalling the wing attach barrel nuts and hardware to
the correct torque value.
Since Japan is the State of Design for the affected airplanes on
one of the two type certificates, did the Japan Civil Airworthiness
Board (JCAB) take any action? The MU-2B series airplane was initially
certificated in 1965 and again in 1976 under two separate type
certificates that consist of basically the same type design. Japan is
the State of Design for TC No. A2PC, and the United States is the State
of Design for TC No. A10SW. The affected models are as follows (where
models are duplicated, specific serial numbers are specified in the
individual TCs):
------------------------------------------------------------------------
Type certificate Affected models
------------------------------------------------------------------------
A10SW................................ MU-2B-25, MU-2B-26, MU-2B-26A, MU-
2B-35, MU-2B-36, MU-2B-36A, MU-
2B-40, and MU-2B-60.
A2PC................................. MU-2B, MU-2B-10, MU-2B-15, MU-2B-
20, MU-2B-25, MU-2B-26, MU-2B-
30, MU-2B-35, and MU-2B-36.
------------------------------------------------------------------------
The JCAB approved Mitsubishi Heavy Industries, Ltd. MU-2 Service
Bulletin referenced as JCAB T.C.: No. 241, dated July 14, 2004, and MU-
2 Service Bulletin referenced FAA T.C.: No. 103/57-004, dated August 2,
2004, to ensure the continued airworthiness of these airplanes in
Japan.
FAA's Determination and Requirements of the Proposed AD
Why have we determined AD action is necessary and what would this
proposed AD require? We are proposing this AD to address an unsafe
condition that we determined is likely to exist or develop on other
products of this same type design. This proposed AD would require you
to do the following:
Remove and visually inspect the wing attach barrel nuts,
bolts, and retainers for cracks, corrosion, and fractures;
Replace any cracked, corroded, or fractured wing attach
barrel nuts, bolts, and retainers with new parts;
Inspect reusable barrel nuts and bolts for deformation and
irregularities in the threads; replace any deformed or irregular wing
attach barrel nuts or bolts with new parts; and
Install new or reusable parts and torque to the correct
value.
This proposed AD would require you to use the service information
described previously to perform these actions.
Costs of Compliance
How many airplanes would this proposed AD impact? We estimate that
this proposed AD affects 397 airplanes in the U.S. registry.
What would be the cost impact of this proposed AD on owners/
operators of the affected airplanes? We estimate the following costs to
do the proposed inspection:
----------------------------------------------------------------------------------------------------------------
Total cost per
Labor cost Parts cost airplane Total cost on U.S. operators
----------------------------------------------------------------------------------------------------------------
1 work hour x $65 per hour = $65.. N/A................ $65 $65 x 397 = $25,805.
----------------------------------------------------------------------------------------------------------------
We estimate the following costs to do any necessary replacements
that would be required based on the results of the proposed inspection.
We have no way of determining the number of airplanes that may need
this replacement:
----------------------------------------------------------------------------------------------------------------
Total cost per airplane to replace all 8
Labor cost Parts cost barrel nuts
----------------------------------------------------------------------------------------------------------------
11 work hours x $65 per hour = $715.. $60 for each barrel nut. $715 + $480 = $1,195.
There are 8 barrel nuts on
each airplane.
Possible total cost of: $60 x
8 = $480..
----------------------------------------------------------------------------------------------------------------
Are there other actions that FAA is issuing that would present a
cost impact on the MU-2B series airplane fleet? This is one of several
actions that FAA is evaluating for unsafe conditions on the MU-2B
airplanes. To date, this is the first proposed AD action to be taken.
Authority for This Rulemaking
What authority does FAA have for issuing this rulemaking action?
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation
[[Page 4074]]
is within the scope of that authority because it addresses an unsafe
condition that is likely to exist or develop on products identified in
this rulemaking action.
Regulatory Findings
Would this proposed AD impact various entities? We have determined
that this proposed AD would not have federalism implications under
Executive Order 13132. This proposed AD would not have a substantial
direct effect on the States, on the relationship between the national
Government and the States, or on the distribution of power and
responsibilities among the various levels of government.
For the reasons discussed above, I certify that the proposed
regulation:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this proposed AD. See the ADDRESSES section for a location
to examine the regulatory evaluation.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the Federal Aviation Administration proposes to amend 14
CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. The Federal Aviation Administration (FAA) amends Sec. 39.13 by
adding the following new airworthiness directive (AD):
Mitsubishi Heavy Industries, Ltd.: Docket No. FAA-2006-23578;
Directorate Identifier 2006-CE-01-AD.
When Is the Last Date I Can Submit Comments on This Proposed AD?
(a) The FAA must receive comments on this AD action by February
27, 2006.
What Other ADs Are Affected by This Action?
(b) None.
What Airplanes Are Affected by This AD?
(c) This AD affects the following Mitsubishi Heavy Industries,
Ltd. airplane models and serial numbers that are certificated in any
category:
------------------------------------------------------------------------
Model Serial numbers
------------------------------------------------------------------------
MU-2B-10..................................... 101 through 347 (Except
313 and 321).
MU-2B-15..................................... 101 through 347 (Except
313 and 321).
MU-2B-20..................................... 101 through 347 (Except
313 and 321).
MU-2B-25..................................... 101 through 347 (Except
313 and 321), 313SA,
321SA, and 348SA through
394SA.
MU-2B-26..................................... 101 through 347 (Except
313 and 321), 313SA,
321SA, and 348SA through
394SA.
MU-2B-26A.................................... 313SA, 321SA, and 348SA
through 394SA.
MU-2B-30..................................... 501 through 696 (Except
652 and 661).
MU-2B-35..................................... 501 through 696 (Except
652 and 661), 652SA,
661SA, and 697SA through
730SA.
MU-2B-36..................................... 501 through 696 (Except
652 and 661), 652SA,
661SA, and 697SA through
730SA.
MU-2B-36A.................................... 652SA, 661SA, and 697SA
through 730SA.
------------------------------------------------------------------------
What Is the Unsafe Condition Presented in This AD?
(d) This AD results from a recent safety evaluation that used a
data-driven approach to evaluate the design, operation, and
maintenance of the MU-2B series airplanes in order to determine
their safety and define what steps, if any, are necessary to ensure
their safe operation. Part of that evaluation was to identify unsafe
conditions that exist or could develop on the affected type design
airplanes. The actions specified in this AD are intended to detect
and correct cracks, corrosion, fractures, and incorrect torque
values in the wing attach barrel nuts, which could result in failure
of the wing barrel nuts and/or associated wing attachment hardware.
This failure could lead to in-flight separation of the outer wing
from the center wing section and result in loss of controlled
flight.
What Must I Do To Address This Problem?
(e) To address this problem, you must do the following, unless
already done:
------------------------------------------------------------------------
Actions Compliance Procedures
------------------------------------------------------------------------
(1) Remove each wing attach Within the next 200 Follow Mitsubishi
barrel nut, bolt, and hours time-in- Heavy Industries,
retainer and do a detailed service (TIS) or 12 Ltd. MU-2 Service
visual inspection for months after the Bulletins
cracks, corrosion, and effective date of referenced as JCAB
fractures. this AD, whichever T.C.: No. 241,
occurs first, dated July 14,
unless already done. 2004, and FAA T.C.:
No. 103/57-004,
dated August 2,
2004, as
applicable.
(2) If any signs of cracks, Before further Follow Mitsubishi
corrosion, or fractures are flight after the Heavy Industries,
found on any wing attach inspection required Ltd. MU-2 Service
barrel nut during the in paragraph (e)(1) Bulletins
inspection required in of this AD, unless referenced as JCAB
paragraph (e)(1) of this already done. T.C.: No. 241,
AD, replace that wing dated July 14,
attach barrel nut, bolt, 2004, and FAA T.C.:
and retainer with new parts No. 103/57-004,
and install to the correct dated August 2,
torque value. 2004, as
applicable, and the
appropriate
maintenance manual.
[[Page 4075]]
(3) If no signs of cracks, Before further Follow Mitsubishi
corrosion, or fractures are flight after the Heavy Industries,
found during the inspection inspection required Ltd. MU-2 Service
required in paragraph in paragraph (e)(1) Bulletins
(e)(1) of this AD, you may of this AD, unless referenced as JCAB
reuse the barrel nuts and already done. T.C.: No. 241,
bolts if they have been dated July 14,
inspected and are free of 2004, and FAA T.C.:
deformation and No. 103/57-004,
irregularities in the dated August 2,
threads. Reinstall 2004, as
inspected parts to the applicable, and the
correct torque value. If appropriate
the barrel nuts and bolts maintenance manual.
are not free of deformation
and irregularities in the
threads, install new parts
to the correct torque value.
------------------------------------------------------------------------
May I Request an Alternative Method of Compliance?
(f) The Manager, Fort Worth Airplane Certification Office, FAA,
has the authority to approve alternative methods of compliance for
this AD, if requested using the procedures found in 14 CFR 39.19.
(g) For information on any already approved alternative methods
of compliance or for information pertaining to this AD, contact
Andrew McAnaul, Aerospace Engineer, ASW-150 (c/o MIDO-43), 10100
Reunion Place, Suite 650, San Antonio, Texas 78216; telephone: (210)
308-3365; facsimile: (210) 308-3370.
Is There Other Information That Relates to This Subject?
(h) Mitsubishi Heavy Industries, Ltd. MU-2 Service Bulletins
JCAB T.C.: No. 241, dated July 14, 2004, and FAA T.C.: No. 103/57-
004, dated August 2, 2004, pertain to the subject of this AD.
May I Get Copies of the Documents Referenced in This AD?
(i) To get copies of the documents referenced in this AD,
contact Mitsubishi Heavy Industries, Ltd., Nagoya Aerospace Systems
Works, 10, OYE-CHO, Minato-Ku, Nagoya, Japan, or Turbine Aircraft
Services, Inc., 4550 Jimmy Doolittle Drive, Addison, Texas 75001;
telephone: (972) 248-3108; facsimile: (972) 248-3321. To view the AD
docket, go to the Docket Management Facility; U.S. Department of
Transportation, 400 Seventh Street, SW., Nassif Building, Room PL-
401, Washington, DC, or on the Internet at http://dms.dot.gov. The
docket number is Docket No. FAA-2006-23578; Directorate Identifier
2006-CE-01-AD.
Issued in Kansas City, Missouri, on January 19, 2006.
John R. Colomy,
Acting Manager, Small Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E6-912 Filed 1-24-06; 8:45 am]
BILLING CODE 4910-13-P