[Federal Register: June 5, 2007 (Volume 72, Number 107)]
[Rules and Regulations]
[Page 30961-30966]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr05jn07-4]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2007-26856; Directorate Identifier 2006-NM-125-AD;
Amendment 39-15082; AD 2007-12-04]
RIN 2120-AA64
Airworthiness Directives; Airbus Model A300 B4-600, B4-600R, and
F4-600R Series Airplanes, and Model C4-605R Variant F Airplanes
(Collectively Called A300-600 Series Airplanes)
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The FAA is superseding an existing airworthiness directive
(AD) that applies to all Airbus Model A300-600 series airplanes. That
AD currently requires inspections of the lower door surrounding
structure to detect cracks and corrosion; inspections to detect
cracking of the holes of the corner doublers, the fail-safe ring, and
the door frames of the door structures; and repair if necessary. That
AD also provides for optional terminating action for certain
inspections. This new AD retains all requirements of the existing AD,
mandates the previously optional terminating action, reduces the
applicability of the existing AD, and adds repetitive inspections
behind scuff plates for certain affected airplanes. This AD results
from a determination that further rulemaking is necessary to improve
the fatigue behavior of the cabin door surroundings. We are issuing
this AD to prevent corrosion between the scuff plates at exit and cargo
doors and fatigue cracks originating from certain fastener holes
located in adjacent structure, which could result in reduced structural
integrity of the door surroundings.
DATES: This AD becomes effective July 10, 2007.
The Director of the Federal Register approved the incorporation by
reference of certain publications listed in the AD as of July 10, 2007.
On September 4, 1998 (63 FR 40812, July 31, 1998), the Director of
the Federal Register approved the incorporation by reference of certain
other publications listed in the AD.
ADDRESSES: You may examine the AD docket on the Internet at http://dms.dot.gov
or in person at the Docket Management Facility, U.S.
Department of Transportation, 400 Seventh Street, SW., Nassif Building,
Room PL-401, Washington, DC.
Contact Airbus, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex,
France, for service information identified in this AD.
FOR FURTHER INFORMATION CONTACT: Tom Stafford, Aerospace Engineer,
International Branch, ANM-116, FAA, Transport Airplane Directorate,
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425)
227-1622; fax (425) 227-1149.
SUPPLEMENTARY INFORMATION:
Examining the Docket
You may examine the airworthiness directive (AD) docket on the
Internet at http://dms.dot.gov or in person at the Docket Management
Facility office between 9 a.m. and 5 p.m., Monday through Friday,
except Federal holidays. The Docket Management Facility office
(telephone (800) 647-5227) is located on the plaza level of the Nassif
Building at the street address stated in the ADDRESSES section.
Discussion
The FAA issued a notice of proposed rulemaking (NPRM) to amend 14
CFR part 39 to include an AD that supersedes AD 98-16-05, amendment 39-
10680 (63 FR 40812, July 31, 1998). The existing AD applies to all
Airbus Model A300-600 series airplanes. That
[[Page 30962]]
NPRM was published in the Federal Register on January 19, 2007 (72 FR
2469). That NPRM proposed to continue the requirements of AD 98-16-05.
These requirements are inspections of the lower door surrounding
structure to detect cracks and corrosion; inspections to detect
cracking of the holes of the corner doublers, the fail-safe ring, and
the door frames of the door structures; and repair if necessary. That
NPRM also proposed to mandate the previously optional terminating
action, reduce the applicability of the existing AD, and add repetitive
inspections behind scuff plates for certain affected airplanes.
Comments
We provided the public the opportunity to participate in the
development of this AD. We have considered the comments that have been
received on the NPRM.
Request To Give Credit for Previous Inspections
FedEx concurs with the NPRM, but requests that we give credit for
previous inspections accomplished in accordance with AD 98-16-05. FedEx
points out that this credit should be given for actions in paragraphs
(f), (g), (j), (k), (n), and (r) of the NPRM.
We partially agree with the request. We agree that it is necessary
for the AD to give credit for inspections accomplished previously in
accordance with AD 98-16-05. We disagree that it is necessary to change
the AD in this regard. Paragraph (e) of the AD states ``You are
responsible for having the actions required by this AD performed within
the compliance times specified, unless the actions have already been
done.'' Therefore, the AD already gives credit for required actions
that were accomplished according to AD 98-16-05.
Request To Allow Previously Granted Alternate Methods of Compliance
(AMOCs)
FedEx also suggests that AMOCs issued per AD 98-16-05 be granted as
applicable to the NPRM.
We agree that we should approve AMOCs for this AD that were
approved previously in accordance with AD 98-16-05. We disagree with
changing the AD in this regard. Paragraph (t)(2) of both the NPRM and
the AD already approves previous AMOCs.
Request To Address Repairs Outside Limits
FedEx requests that we add wording to paragraphs (l)(2) and (t) of
the NPRM to address repairs outside the applicable service bulletins or
that exceed the service bulletin limits. (Airbus Service Bulletin A300-
53-6018, Revision 1, dated April 29, 1992; or Revision 02, dated
November 27, 2000; are the applicable service bulletins for paragraph
(l)(2); and paragraph (t) is the AMOC paragraph.) FedEx suggests the
following wording: ``If any crack or corrosion is detected during any
inspection required by this AD and the applicable service bulletin
specifies to contact the manufacturer for disposition of corrective
actions: Prior to further flight, repair in accordance with a method
approved by either the Manager, International Branch, ANM-116, or DGAC/
EASA, or its delegated agent.''
We disagree with the request to add the suggested words. There are
no limits specified in the service bulletins. We cannot approve repairs
that exceed the limits of the service bulletin unless the excess limits
are defined. However, affected operators may request approval of AMOCs,
under the provisions of paragraph (t) of the AD.
Conclusion
We have carefully reviewed the available data, including the
comments that have been submitted, and determined that air safety and
the public interest require adopting the AD as proposed.
Costs of Compliance
The following table provides the estimated costs for U.S. operators
to comply with this AD. The average labor rate per work hour is $80.
Estimated Costs
----------------------------------------------------------------------------------------------------------------
Number of U.S.-
Action Work hours Parts Cost per registered Fleet cost
airplane airplanes
----------------------------------------------------------------------------------------------------------------
Repetitive inspections 37............. None........... $2,960......... 129 $381,840.
behind scuff plates.
Repetitive inspections of Between 1 and None........... Between $80 and 129 Between $10,320
corner doublers, fail-safe 51. $4,080. and $526,320.
ring, and door frames.
Terminating modification for Between 8 and Between $580 Between $1,220 129 Between
repetitive inspection of 67, depending and $11,273, and $16,633. $157,380 and
corner doublers, fail-safe on kit depending on $2,145,657.
ring, and door frames. purchased. kit purchased.
----------------------------------------------------------------------------------------------------------------
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We have determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
[[Page 30963]]
(1) Is not a ``significant regulatory action'' under Executive
Order 12866;
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this AD and placed it in the AD docket. See the ADDRESSES
section for a location to examine the regulatory evaluation.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
0
Accordingly, under the authority delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The Federal Aviation Administration (FAA) amends Sec. 39.13 by
removing amendment 39-10680 (63 FR 40812, July 31, 1998) and by adding
the following new airworthiness directive (AD):
2007-12-04 Airbus: Amendment 39-15082. Docket No. FAA-2007-26856;
Directorate Identifier 2006-NM-125-AD.
Effective Date
(a) This AD becomes effective July 10, 2007.
Affected ADs
(b) This AD supersedes AD 98-16-05.
Applicability
(c) This AD applies to Airbus Model A300 B4-601, B4-603, B4-620,
and B4-622 airplanes; Model A300 B4-605R and B4-622R airplanes;
Model A300 F4-605R and F4-622R airplanes; and Model A300 C4-605R
Variant F airplanes; certificated in any category; excluding those
airplanes on which Airbus Modification 5068, 6514, 7201, and 7298
have been incorporated in production.
Unsafe Condition
(d) This AD results from a determination that further rulemaking
is necessary to improve the fatigue behavior of the cabin door
surroundings. We are issuing this AD to prevent corrosion between
the scuff plates at exit and cargo doors and fatigue cracks
originating from certain fastener holes located in adjacent
structure, which could result in reduced structural integrity of the
door surroundings.
Compliance
(e) You are responsible for having the actions required by this
AD performed within the compliance times specified, unless the
actions have already been done.
Requirements of AD 98-16-05
Initial Inspection Behind Scuff Plates and Repair if Necessary
(f) Perform an initial inspection of the areas behind the scuff
plates below the passenger/crew doors and bulk cargo door to detect
cracks and corrosion, in accordance with Airbus Service Bulletin
A300-53-6011, Revision 3, dated February 4, 1991, at the time
specified in paragraph (f)(1), (f)(2), or (f)(3) of this AD. If any
crack or corrosion is found during this inspection, prior to further
flight, repair in accordance with the service bulletin.
Accomplishment of this inspection is not required for the mid and
aft passenger/crew doors if a steel doubler that covers the entire
inspection area is installed.
(1) For airplanes on which Modification 5382S6526 (for forward
doors) and Modification 5382D4741 (for all other doors) have been
accomplished prior to delivery of the airplane: Perform the initial
inspection within 9 years since date of manufacture, or within 1
year after September 4, 1998 (the effective date of AD 98-16-05),
whichever occurs later.
(2) For airplanes on which Modification 5382S6526 (for forward
doors) and Modification 5382D4741 (for all other doors) have not
been accomplished; and on which the procedures described in Airbus
Service Information Letter (SIL) A300-53-033, Revision 2 (for all
doors), dated November 23, 1984, have been accomplished: Perform the
initial inspection within 5 years after accomplishment of the
procedures described in the SIL, or within 1 year after September 4,
1998, whichever occurs later.
(3) For airplanes on which Modification 5382S6526 (for forward
doors), and Modification 5382D4741 (for all other doors), and the
procedures described in Airbus SIL A300-53-033, Revision 2, dated
November 23, 1984, have not been accomplished: Perform the initial
inspection within 4 years since date of manufacture, or within 1
year after September 4, 1998, whichever occurs later.
Repetitive Inspections Behind Scuff Plates
(g) Perform repetitive inspections of the areas behind the scuff
plates below the passenger/crew doors and bulk cargo door to detect
cracks and corrosion, in accordance with Airbus Service Bulletin
A300-53-6022, dated February 4, 1991, at the applicable times
specified in paragraphs (g)(1) and (g)(2) of this AD. Accomplishment
of these inspections is not required for the mid and aft passenger/
crew doors if a steel doubler that covers the entire inspection area
is installed.
(1) For the forward and mid passenger/crew doors, the bulk cargo
door, and the aft passenger/crew doors, except the upper and lower
edges of the fail-safe ring and the upper edges of the corner
doubler: Perform the first inspection within 5 years after
accomplishing the inspection required by paragraph (f) of this AD;
and repeat the inspection thereafter at intervals not to exceed 5
years.
(2) For the upper and lower edges of the fail-safe ring and the
upper edges of the corner doubler of the aft passenger/crew doors:
Perform the first inspection within 5 years or 6,000 landings after
accomplishing the inspection required by paragraph (f) of this AD,
whichever occurs first; and repeat the inspection thereafter at
intervals not to exceed 5 years or 6,000 landings, whichever occurs
first.
Repair of Scuff Plates if Necessary
(h) If any crack is found during any inspection required by
paragraph (g) of this AD, prior to further flight, repair in
accordance with Airbus Service Bulletin A300-53-6022, dated February
4, 1991. Thereafter, perform the repetitive inspections required by
paragraph (g) of this AD at the applicable times specified in
paragraphs (g)(1) and (g)(2) of this AD.
(i) If corrosion is found during any inspection required by
paragraph (g) of this AD, prior to further flight, repair in
accordance with Airbus Service Bulletin A300-53-6022, dated February
4, 1991. Thereafter, perform the repetitive inspections required by
paragraph (g) of this AD at the applicable times specified in
paragraph (i)(1) or (i)(2) of this AD.
(1) For the upper and lower edges of the fail-safe ring and the
upper edges of the corner doubler of the aft passenger/crew doors,
and for the mid passenger/crew door: Inspect at intervals not to
exceed 5 years or 5,000 landings, whichever occurs first.
(2) For the forward passenger/crew doors and bulk cargo doors:
Inspect at intervals not to exceed 5 years.
Initial Inspection of Corner Doublers, Fail-Safe Ring, and Door Frames
(j) Perform an inspection to detect cracking of the holes of the
corner doublers, the fail-safe ring, and the door frames of the
left- and right-hand forward, mid, and aft passenger/crew door
structures, in accordance with Airbus Service Bulletin A300-53-6018,
Revision 1, dated April 29, 1992, and at the applicable time
specified in paragraph (j)(1), (j)(2), (j)(3), or (j)(4) of this AD.
(1) For the upper corners of the forward doors: Inspect prior to
the accumulation of 20,000 total landings, or within 2,000 landings
after September 4, 1998, whichever occurs later.
(2) For the lower corners of the forward doors: Inspect prior to
the accumulation of 20,000 total landings, or within 4,000 landings
after September 4, 1998, whichever occurs later.
(3) For the upper and lower corners of the mid doors: Inspect
prior to the accumulation of 20,000 total landings, or within 2,000
landings after September 4, 1998, whichever occurs later.
(4) For the upper and lower corners of the aft doors, and for
the parts underneath the corners of the upper door frames: Inspect
prior to the accumulation of 20,000 total landings, or within 4,000
landings after September 4, 1998, whichever occurs later.
[[Page 30964]]
Repetitive Inspections of Corner Doublers, Fail-Safe Ring, and Door
Frames
(k) Repeat the inspections required by paragraph (j) of this AD
at the applicable times specified in paragraphs (k)(1), (k)(2),
(k)(3), (k)(4), and (k)(5) of this AD.
(1) For the upper corners of the forward doors: Inspect at
intervals not to exceed 6,000 landings.
(2) For the lower corners of the forward doors: Inspect at
intervals not to exceed 10,000 landings.
(3) For the upper and lower corners of the mid and aft doors on
which an inspection required by paragraph (j) of this AD was
accomplished using a ROTO test technique: Inspect at intervals not
to exceed 8,000 landings.
(4) For the upper and lower corners of the mid and aft doors on
which an inspection required by paragraph (j) of this AD was
accomplished using an X-ray technique: Inspect at intervals not to
exceed 3,500 landings.
(5) For the areas around the fasteners in the vicinity of
stringer 12 on the upper door frames of the aft doors on which an
inspection required by paragraph (j) of this AD was accomplished
using a visual technique: Inspect at intervals not to exceed 6,900
landings.
Repair of Corner Doublers, Fail-Safe Ring, and/or Door Frames if
Necessary
(l) If any crack is found during any inspection required by
paragraph (j) or (k) of this AD: Prior to further flight, accomplish
the requirement of paragraph (l)(1) or (l)(2) of this AD, as
applicable.
(1) If any crack is found, and the crack can be eliminated using
the method specified in Airbus Service Bulletin A300-53-6018,
Revision 1, dated April 29, 1992; or Revision 02, excluding Appendix
01, dated November 27, 2000: Prior to further flight, repair the
crack in accordance with that service bulletin.
(2) If any crack is found, and the crack cannot be eliminated
using the method specified in Airbus Service Bulletin A300-53-6018,
Revision 1, dated April 29, 1992; or Revision 02, excluding Appendix
01, dated November 27, 2000: Prior to further flight, repair the
crack in accordance with a method approved by the Manager,
International Branch, ANM-116, FAA, Transport Airplane Directorate.
New Requirements of This AD
New Revisions of Service Bulletins
(m) As of the effective date of this AD, use only the applicable
service bulletins specified in Table 1 of this AD; except where the
service bulletins recommend contacting Airbus for appropriate
action, before further flight, repair the cracked part using a
method approved by the Manager, International Branch, ANM-116,
Transport Airplane Directorate, FAA; or the European Aviation Safety
Agency (EASA) (or its delegated agent).
Table 1.--New Revisions of Service Bulletins
--------------------------------------------------------------------------------------------------------------------------------------------------------
Do the action(s) required by-- In accordance with the accomplishment instructions of Airbus Service Bulletin--
--------------------------------------------------------------------------------------------------------------------------------------------------------
(1) Paragraph (f) of this AD............. A300-53-6011, Revision 07, dated January 24, 2005.
(2) Paragraphs (g) through (i) of this AD A300-53-6022, Revision 04, dated January 24, 2005.
(3) Paragraphs (j), (k), and (l)(1) of A300-53-6018, Revision 03, excluding Appendix 01, dated July 26, 2006.
this AD.
--------------------------------------------------------------------------------------------------------------------------------------------------------
Initial Inspection Behind Scuff Plates and Repair if Necessary for
Additional Airplanes
(n) Perform an initial inspection of the areas behind the scuff
plates below the passenger/crew doors and bulk cargo door to detect
cracks and corrosion, in accordance with the Accomplishment
Instructions of Airbus Service Bulletin A300-53-6011, Revision 07,
dated January 24, 2005; at the applicable time specified in Table 2
of this AD. If any crack or corrosion is found during this
inspection, before further flight, repair in accordance with the
service bulletin. Accomplishment of this inspection is not required
for the mid and aft passenger/crew doors if a steel doubler that
covers the entire inspection area is installed.
Table 2.--Compliance Time Initial Inspection Behind Scuff Plate for Additional Airplanes
----------------------------------------------------------------------------------------------------------------
Compliance time (whichever occurs later)
For airplanes on which-- And on which-- -------------------------------------------------
Threshold Grace period
----------------------------------------------------------------------------------------------------------------
(1) Modification 5382S6526 (for None................... Within 108 months after Within 12 months after
forward doors) and Modification first flight. the effective date of
5382D4485 (for all other doors) have this AD.
been done before the date of
issuance of the original French
standard airworthiness certificate
or the date of issuance of the
original French export certificate
of airworthiness.
(2) Modification 5382S6180 (for None................... Within 108 months after Within 12 months after
forward doors) and Modification first flight. the effective date of
5382D4741 or 5382D4485 (for all this AD.
other doors) have been done before
the date of issuance of the original
French standard airworthiness
certificate or the date of issuance
of the original French export
certificate of airworthiness.
(3) Modification 5382S6526 (for The actions specified Within 60 months after Within 12 months after
forward doors) and Modification in Airbus Service accomplishing the the effective date of
5382D4485 (for all other doors) have Information Letter actions specified in this AD.
not been done before the effective (SIL) A300-53-033, the SIL.
date of this AD. Revision 2 (for all
doors), dated November
23, 1984, have been
done.
[[Page 30965]]
(4) Modification 5382S6180 (for The actions specified Within 60 months after Within 12 months after
forward doors) and Modification in Airbus SIL A300-53- accomplishing the the effective date of
5382D4741 or 5382D4485 (for all 033, Revision 2 (for actions specified in this AD.
other doors) have not been done all doors), dated the SIL.
before the effective date of this AD. November 23, 1984,
have been done.
(5) Modification 5382S6526 (for The actions specified Within 48 months since Within 12 months after
forward doors) and Modification in Airbus SIL A300-53- the date of issuance the effective date of
5382D4485 (for all other doors) have 033, Revision 2, dated of the original French this AD.
not been done before the effective November 23, 1984, standard airworthiness
date of this AD. have not been done. certificate or the
date of issuance of
the original French
export certificate of
airworthiness.
(6) Modification 5382S6180 (for The actions specified Within 48 months since Within 12 months after
forward doors) and Modification in Airbus SIL A300-53- the date of issuance the effective date of
5382D4741 or 5382D4485 (for all 033, Revision 2, dated of the original French this AD.
other doors) have not been done November 23, 1984, standard airworthiness
before the effective date of this AD. have not been done. certificate or the
date of issuance of
the original French
export certificate of
airworthiness.
----------------------------------------------------------------------------------------------------------------
Repetitive Inspections Behind Scuff Plates for Additional Airplanes
(o) For airplanes identified in Table 2 of this AD: Perform
repetitive inspections of the areas behind the scuff plates below
the passenger/crew doors and bulk cargo door to detect cracks and
corrosion, in accordance with Airbus Service Bulletin A300-53-6022,
Revision 04, dated January 24, 2005, at the applicable times
specified in paragraphs (o)(1) and (o)(2) of this AD. Accomplishment
of these inspections is not required for the mid and aft passenger/
crew doors if a steel doubler that covers the entire inspection area
is installed.
(1) For the forward and mid passenger/crew doors, the bulk cargo
door, and the aft passenger/crew doors, except the upper and lower
edges of the fail-safe ring and the upper edges of the corner
doubler: Perform the first inspection within 60 months after
accomplishing the inspection required by paragraph (n) of this AD;
and repeat the inspection thereafter at intervals not to exceed 60
months.
(2) For the upper and lower edges of the fail-safe ring and the
upper edges of the corner doubler of the aft passenger/crew doors:
Perform the first inspection within 60 months or 6,000 landings
after accomplishing the inspection required by paragraph (n) of this
AD, whichever occurs first; and repeat the inspection thereafter at
intervals not to exceed 60 months or 6,000 landings, whichever
occurs first.
Repair of Scuff Plates if Necessary
(p) If any crack is found during any inspection required by
paragraph (o) of this AD, prior to further flight, repair in
accordance with Airbus Service Bulletin A300-53-6022, Revision 04,
dated January 24, 2005. Thereafter, perform the repetitive
inspections required by paragraph (o) of this AD at the applicable
times specified in paragraphs (o)(1) and (o)(2) of this AD.
(q) If corrosion is found during any inspection required by
paragraph (o) of this AD, prior to further flight, repair in
accordance with Airbus Service Bulletin A300-53-6022, Revision 04,
dated January 24, 2005. Thereafter, perform the repetitive
inspections required by paragraph (g) of this AD at the applicable
times specified in paragraph (q)(1) or (q)(2) of this AD.
(1) For the upper and lower edges of the fail-safe ring and the
upper edges of the corner doubler of the aft passenger/crew doors,
and for the mid passenger/crew door: Inspect at intervals not to
exceed 60 months or 5,000 landings, whichever occurs first.
(2) For the forward passenger/crew doors and bulk cargo doors:
Inspect at intervals not to exceed 60 months.
Terminating Modification for Repetitive Inspection of Corner Doublers,
Fail-Safe Ring, and Door Frames
(r) Before the accumulation of 30,000 total flight cycles since
the date of issuance of the original French standard airworthiness
certificate or the date of issuance of the original French export
certificate of airworthiness, or during the next inspection required
by paragraph (k) of this AD, whichever occurs later: Modify the
passenger/crew door structures in accordance with the Accomplishment
Instructions of Airbus Service Bulletin A300-53-6002, Revision 06,
dated May 17, 2004. Accomplishment of this modification constitutes
terminating action for the inspections required by paragraphs (j)
and (k) of this AD. The inspections required by paragraphs (f) and
(n) of this AD, as applicable, must be done before accomplishing
this modification.
Earlier Revisions of Service Bulletins
(s) Actions done before the effective date of this AD in
accordance with the service bulletins identified in Table 3 of this
AD, are acceptable for compliance with the corresponding
requirements of this AD.
Table 3.--Earlier Revisions of Service Bulletins
----------------------------------------------------------------------------------------------------------------
Airbus Service Bulletin Revision level Date
----------------------------------------------------------------------------------------------------------------
(1) A300-53-6002........................ 3........................... February 22, 1992.
(2) A300-53-6002........................ 4........................... July 13, 1992.
(3) A300-53-6002........................ 05.......................... September 7, 2000.
(4) A300-53-6011........................ 04.......................... July 2, 1996.
(5) A300-53-6011........................ 05.......................... September 7, 2000.
(6) A300-53-6011........................ 06.......................... November 12, 2002.
(7) A300-53-6018, excluding Appendix 01. 02.......................... November 27, 2000.
(8) A300-53-6022........................ 01.......................... July 2, 1996.
(9) A300-53-6022........................ 02.......................... September 7, 2000.
[[Page 30966]]
(10) A300-53-6022....................... 03.......................... November 12, 2002.
----------------------------------------------------------------------------------------------------------------
Alternative Methods of Compliance (AMOCs)
(t)(1) The Manager, International Branch, ANM-116, has the
authority to approve AMOCs for this AD, if requested in accordance
with the procedures found in 14 CFR 39.19.
(2) AMOCs approved previously in accordance with AD 98-16-05 are
approved as AMOCs for the corresponding provisions of paragraphs (f)
through (l) of this AD.
(3) Before using any AMOC approved in accordance with Sec.
39.19 on any airplane to which the AMOC applies, notify the
appropriate principal inspector in the FAA Flight Standards
Certificate Holding District Office.
Related Information
(u) French airworthiness directives 1991-132-124(B) R1, dated
November 29, 2000, and F-2004-103, dated July 7, 2004, also address
the subject of this AD.
Material Incorporated by Reference
(v) You must use the service information listed in Table 4 of
this AD to perform the actions that are required by this AD, unless
the AD specifies otherwise.
Table 4.--All Material Incorporated by Reference
----------------------------------------------------------------------------------------------------------------
Airbus Service Bulletin Revision level Date
----------------------------------------------------------------------------------------------------------------
A300-53-6002............................ 06.......................... May 17, 2004.
A300-53-6011............................ 3........................... February 4, 1991.
A300-53-6011............................ 07.......................... January 24, 2005.
A300-53-6018............................ 1........................... April 29, 1992.
A300-53-6018, excluding Appendix 01..... 02.......................... November 27, 2000.
A300-53-6018, excluding Appendix 01..... 03.......................... July 26, 2006.
A300-53-6022............................ Original.................... February 4, 1991.
A300-53-6022............................ 04.......................... January 24, 2005.
----------------------------------------------------------------------------------------------------------------
(1) The Director of the Federal Register approved the
incorporation by reference of the service information listed in
Table 5 of this AD in accordance with 5 U.S.C. 552(a) and 1 CFR part
51.
Table 5.--New Material Incorporated by Reference
----------------------------------------------------------------------------------------------------------------
Airbus Service Bulletin Revision level Date
----------------------------------------------------------------------------------------------------------------
A300-53-6002............................ 06.......................... May 17, 2004.
A300-53-6011............................ 07.......................... January 24, 2005.
A300-53-6018, excluding Appendix 01..... 02.......................... November 27, 2000.
A300-53-6018, excluding Appendix 01..... 03.......................... July 26, 2006.
A300-53-6022............................ 04.......................... January 24, 2005.
----------------------------------------------------------------------------------------------------------------
(2) On September 4, 1998 (63 FR 40812, July 31, 1998), the
Director of the Federal Register approved the incorporation by
reference of the service information listed in Table 6 of this AD.
Table 6.--Material Previously Incorporated by Reference
----------------------------------------------------------------------------------------------------------------
Airbus Service Bulletin Revision level Date
----------------------------------------------------------------------------------------------------------------
A300-53-6011........................... 3........................... February 4, 1991.
A300-53-6018............................ 1........................... April 29, 1992.
A300-53-6022............................ Original.................... February 4, 1991.
----------------------------------------------------------------------------------------------------------------
(3) Contact Airbus, 1 Rond Point Maurice Bellonte, 31707 Blagnac
Cedex, France, for a copy of this service information. You may
review copies at the FAA, Transport Airplane Directorate, 1601 Lind
Avenue, SW., Renton, Washington; or at the National Archives and
Records Administration (NARA). For information on the availability
of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html
.
Issued in Renton, Washington, on May 25, 2007.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E7-10671 Filed 6-4-07; 8:45 am]
BILLING CODE 4910-13-P