[Federal Register: August 13, 2007 (Volume 72, Number 155)]
[Rules and Regulations]
[Page 45153-45156]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr13au07-4]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2007-28478; Directorate Identifier 2007-CE-057-AD;
Amendment 39-15153; AD 2007-16-14]
RIN 2120-AA64
Airworthiness Directives; Taylorcraft A, B, and F Series
Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule; request for comments.
-----------------------------------------------------------------------
SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all
Taylorcraft A, B, and F series airplanes. This AD requires you to
initially inspect the left and right wing front and aft lift struts for
corrosion and cracks, replace any cracked strut or strut with corrosion
that exceeds certain limits with either sealed or non-sealed struts,
and repetitively inspect any non-sealed struts. This AD results from
inspections
[[Page 45154]]
where several different struts were found with moderate to severe
corrosion and required strut replacement. We are issuing this AD to
detect and correct corrosion or cracks in the right and left wing front
and aft lift struts. This condition, if not corrected, could result in
failure of the lift strut and lead to in-flight separation of the wing
with consequent loss of control.
DATES: This AD becomes effective on August 20, 2007.
On August 20, 2007, the Director of the Federal Register approved
the incorporation by reference of certain publications listed in this
AD.
We must receive any comments on this AD by October 12, 2007.
ADDRESSES: Use one of the following addresses to comment on this AD.
DOT Docket Web site: Go to http://dms.dot.gov and follow
the instructions for sending your comments electronically.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue, SE., Washington, DC 20590.
Fax: (202) 493-2251.
Hand Delivery: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m.,
Monday through Friday, except Federal holidays.
Federal eRulemaking Portal: Go to http://www.regulations.gov.
Follow the instructions for submitting comments.
To get the service information identified in this AD, contact
Taylorcraft Aviation, LLC, 2124 North Central Avenue, Brownsville,
Texas 78521; telephone: (956) 986-0700.
To view the comments to this AD, go to http://dms.dot.gov. The
docket number is FAA-2007-28478; Directorate Identifier 2007-CE-057-AD.
FOR FURTHER INFORMATION CONTACT: Andrew McAnaul, Aerospace Engineer,
ASW-150 (c/o MIDO-43), 10100 Reunion Place, Suite 650, San Antonio,
Texas 78216; telephone: (210) 308-3365; fax: (210) 308-3370.
SUPPLEMENTARY INFORMATION:
Discussion
The FAA has received reports of several corroded wing lift struts
from different Taylorcraft series airplanes. Independent laboratory
analysis of the struts revealed varying degrees of excessive internal
and external corrosion, including through-the-thickness corrosion. The
struts exhibited corrosion severe enough to require strut replacement.
Additional Taylorcraft owners reported finding severe corrosion on wing
struts during routine maintenance, which required strut replacement.
These same findings confirm strut corrosion Taylorcraft reported to the
FAA. The internal cavity of the original design (vented) lift struts is
exposed to the external environment and can hide internal surface
corrosion resulting from environmental exposure. External surface
corrosion can be masked by the external paint coating.
This condition, if not corrected, could result in failure of a wing
lift strut due to corrosion and lead to separation of the wing from the
airplane with consequent loss of control.
Relevant Service Information
We reviewed Taylorcraft Aviation, LLC Service Bulletin (SB) No.
2007-001, Revision A, dated August 1, 2007. The service information
describes procedures for wing lift strut assembly corrosion inspection
and/or replacement.
FAA's Determination and Requirements of This AD
We are issuing this AD because we evaluated all the information and
determined the unsafe condition described previously is likely to exist
or develop on other products of the same type design. This AD requires
you to initially inspect the left and right wing front and aft lift
struts for corrosion and cracks, replace any cracked strut or strut
with corrosion that exceeds certain limits with either sealed or non-
sealed struts, and repetitively inspect any non-sealed struts.
The FAA is determining whether future rulemaking action is
necessary. This could include inspection and/or modification or
replacement in adjacent structure.
In preparing this rule, we contacted type clubs and aircraft
operators to get technical information and information on operational
and economic impacts. We have included a discussion of information that
may have influenced this action in the rulemaking docket.
FAA's Determination of the Effective Date
An unsafe condition exists that requires the immediate adoption of
this AD. The FAA has found that the risk to the flying public justifies
waiving notice and comment prior to adoption of this rule because
corrosion and/or cracks in the wing lift struts could result in
separation of the wing from the airplane with consequent loss of
control. Therefore, we determined that notice and opportunity for
public comment before issuing this AD are impracticable and that good
cause exists for making this amendment effective in fewer than 30 days.
Comments Invited
This AD is a final rule that involves requirements affecting flight
safety, and we did not precede it by notice and an opportunity for
public comment. We invite you to send any written relevant data, views,
or arguments regarding this AD. Send your comments to an address listed
under the ADDRESSES section. Include the docket number ``FAA-2007-
28478; Directorate Identifier 2007-CE-057-AD'' at the beginning of your
comments. We specifically invite comments on the overall regulatory,
economic, environmental, and energy aspects of the AD. We will consider
all comments received by the closing date and may amend the AD in light
of those comments.
We will post all comments we receive, without change, to http://dms.dot.gov
, including any personal information you provide. We will
also post a report summarizing each substantive verbal contact we
receive concerning this AD.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We determined that this AD will not have federalism implications
under Executive Order 13132. This AD will not have a substantial direct
effect on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
[[Page 45155]]
(1) Is not a ``significant regulatory action'' under Executive
Order 12866;
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this AD and placed it in the AD docket.
Examining the AD Docket
You may examine the AD docket that contains the AD, the regulatory
evaluation, any comments received, and other information on the
Internet at http://dms.dot.gov; or in person at the Docket Management
Facility between 9 a.m. and 5 p.m., Monday through Friday, except
Federal holidays. The Docket Office (telephone (800) 647-5527) is
located at the street address stated in the ADDRESSES section. Comments
will be available in the AD docket shortly after receipt.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
0
Accordingly, under the authority delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new airworthiness
directive (AD):
2007-16-14 Taylorcraft: Amendment 39-15153; Docket No. FAA-2007-
28478; Directorate Identifier 2007-CE-057-AD.
Effective Date
(a) This AD becomes effective on August 20, 2007.
Affected ADs
(b) None.
Applicability
(c) This AD applies to all serial numbers of Taylorcraft Models
A, BC, BCS, BC-65, BCS-65, BC12-65 (Army L-2H), BCS12-65, BC12-D,
BCS12-D, BC12-D1, BCS12-D1, BC12D-85, BCS12D-85, BC12D-4-85, BCS12D-
4-85, (Army L-2G) BF, BFS, BF-60, BFS-60, BF-65, BFS-65, (Army L-2K)
BF 12-65, BL, BLS, (Army L-2F) BL-65, BLS-65, (Army L-2J) BL12-65,
BLS12-65, FA-III (Airphibian), 19, F19, F21, F21A, F21B, F22, F22A,
F22B, F22C, and TG-6 Conversion airplanes that:
(1) Are certificated in any category; and
(2) Do not incorporate in all struts new sealed front lift
struts (P/N MA-A815 or FAA-approved equivalent P/N) and new sealed
aft lift struts (P/N MA-A854 or FAA-approved equivalent P/N).
Note: This AD applies to all Taylorcraft models listed above,
including those not listed in Taylorcraft Aviation, LLC Service
Bulletin No. 2007-001, Revision A, dated August 1, 2007. If there
are any other differences between this AD and the above service
bulletin, this AD takes precedence.
Unsafe Condition
(d) This AD results from inspections where several different
struts were found with moderate to severe corrosion and required
strut replacement. We are issuing this AD to detect and correct
corrosion or cracks in the right and left wing front and aft lift
struts, which could result in failure of the lift strut and lead to
in-flight separation of the wing with consequent loss of control.
Compliance
(e) To address this problem, you must do the following, unless
already done:
----------------------------------------------------------------------------------------------------------------
Actions Compliance Procedures
----------------------------------------------------------------------------------------------------------------
(1) Visual Inspection: Visually Within the next 5 hours time-in- Follow Part 1 of the Instructions in
inspect for corrosion or cracking service after August 20, 2007 (the Taylorcraft Aviation, LLC Service
in the lower 12 inches of the left effective date of this AD), unless Bulletin No. 2007-001, Revision A,
and right wing front lift struts the strut has: dated August 1, 2007.
(part number (P/N) A-A815 or FAA- (i) Been replaced with parts
approved equivalent P/N) and aft specified in either paragraph
lift struts (P/N A-A854 or FAA- (e)(4)(i); or
approved equivalent P/N) and then (ii) Been replaced with parts
inspect per paragraph (e)(2) of specified by paragraph (e)(4)(ii)
this AD. of this AD and been installed on an
airplane for less than 24 months.
(2) Initial Eddy Current or Initially inspect any original Follow Part 2 of the Instructions in
Ultrasound Inspection: Inspect design (vented) strut or FAA- Taylorcraft Aviation, LLC Service
using the eddy current or approved equivalent part number at Bulletin No. 2007-001, Revision A,
ultrasound inspection methods to whichever of the following that dated August 1, 2007.
detect corrosion or cracking in the applies:
lower 12 inches of the left and (A) Before further flight when
right wing front lift struts (P/N A- corrosion or cracking is found
A815 or FAA-approved equivalent P/ during the visual inspection
N) and aft lift struts (P/N A-A854 required in paragraph (e)(1) of
or FAA-approved equivalent P/N). this AD; or
The eddy current or ultrasound (B) If no corrosion or cracking is
inspection must be done by one of found during the visual inspection
the following: in paragraph (e)(1) of this AD,
(i) A Level II or III inspector within the next 3 months after
certified in the applicable eddy August 20, 2007 (the effective date
current or ultrasound inspection of this AD) or within 24 months of
method using the guidelines installation of the strut,
established by the American Society whichever occurs later.
of Nondestructive Testing or NAS
410 (formerly MIL-STD-410);
(ii) An inspector certified to
specific FAA or other acceptable
government or industry standards,
such as Air Transport Association
(ATA) Specifications 105--
Guidelines for Training and
Qualifying Personnel in
Nondestructive Testing Methods; or
(iii) A qualified FAA Repair Station
or a qualified Testing/Inspection
Laboratory.
[[Page 45156]]
(3) Repetitive Eddy Current or (A) For original or replacement left Follow Part 2 of the Instructions in
Ultrasound Inspections: Inspect and right wing front lift struts (P/ Taylorcraft Aviation, LLC Service
using the eddy current or N A-A815 or FAA-approved equivalent Bulletin No. 2007-001, Revision A,
ultrasound inspection methods to P/N) and aft lift struts (P/N A- dated August 1, 2007.
detect corrosion or cracking in the A854 or FAA-approved equivalent P/
lower 12 inches of the left and N) of original design (vented),
right wing front lift struts (P/N A- repetitively inspect at intervals
A815 or FAA-approved equivalent P/ not to exceed 24 months after the
N) and aft lift struts (P/N A-A854 initial inspection required in
or FAA-approved equivalent P/N). paragraph (e)(2) of this AD.
The eddy current or ultrasound (B) Replacement of all struts with
inspection must be done by one of new sealed front lift struts (P/N
the following: MA-A815 or FAA-approved equivalent
(i) A Level II or III inspector P/N) and new sealed aft lift struts
certified in the applicable Eddy (P/N MA-A854 or FAA-approved
Current or Ultrasound Inspection equivalent P/N) eliminates the
method using the guidelines repetitive inspection requirement
established by the American Society of this AD.
of Nondestructive Testing or NAS (C) If not all the vented lift
410 (formerly MIL-STD-410), struts are replaced with new sealed
(ii) An Inspector certified to units, then the lift struts that
specific FAA or other acceptable are not new sealed units are still
government or industry standards, subject to the repetitive
such as Air Transport Association inspection requirement of this AD.
(ATA) Specifications 105--
Guidelines for Training and
Qualifying Personnel in
Nondestructive Testing Methods, or
(iii) A qualified FAA Repair Station
or a qualified Testing/Inspection
Laboratory.
(4) Replacement: Replace the Replace before further flight any Follow Taylorcraft Aviation, LLC
original design (vented) front lift time cracking or corrosion is found Service Bulletin No. 2007-001,
struts (P/N A-A815 or FAA-approved during any required eddy current or Revision A, dated August 1, 2007.
equivalent P/N) and original design ultrasound inspection that exceeds
(vented) aft lift struts (P/N A- the acceptance/rejection criteria
A854 or FAA-approved equivalent P/ limits in Taylorcraft Aviation, LLC
N) with one of the following: Service Bulletin No. 2007-001,
(i) new sealed front lift struts, (P/ Revision A, dated August 1, 2007.
N MA-A815 or FAA-approved After replacing with an original
equivalent P/N) and new sealed aft design (vented) strut, begin the
lift struts, (P/N MA-A854 or FAA- repetitive inspections of paragraph
approved equivalent P/N); or (e)(3) within 24 months after
(ii) New original design (vented) installation.
front lift struts (P/N A-815 or FAA-
approved equivalent P/N) and new
original design (vented) aft lift
struts (P/N A-A854 or FAA-approved
equivalent P/N).
----------------------------------------------------------------------------------------------------------------
Alternative Methods of Compliance (AMOCs)
(f) The Manager, Fort Worth Airplane Certification Office, FAA,
has the authority to approve AMOCs for this AD, if requested using
the procedures found in 14 CFR 39.19. Send information to ATTN:
Andrew McAnaul, Aerospace Engineer, ASW-150 (c/o MIDO-43), 10100
Reunion Place, Suite 650, San Antonio, Texas 78216; telephone: (210)
308-3365; fax: (210) 308-3370. Before using any approved AMOC on any
airplane to which the AMOC applies, notify your appropriate
principal inspector (PI) in the FAA Flight Standards District Office
(FSDO), or lacking a PI, your local FSDO.
Material Incorporated by Reference
(g) You must use Taylorcraft Aviation, LLC Service Bulletin No.
2007-001, Revision A, dated August 1, 2007, to do the actions
required by this AD, unless the AD specifies otherwise.
(1) The Director of the Federal Register approved the
incorporation by reference of this service information under 5
U.S.C. 552(a) and 1 CFR part 51.
(2) For service information identified in this AD, contact
Taylorcraft Aviation, LLC, 2124 North Central Avenue, Brownsville,
Texas 78521; telephone: 956-986-0700.
(3) You may review copies at the FAA, Central Region, Office of
the Regional Counsel, 901 Locust, Kansas City, Missouri 64106; or at
the National Archives and Records Administration (NARA). For
information on the availability of this material at NARA, call 202-
741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html
.
Issued in Kansas City, Missouri, on August 3, 2007.
David R. Showers,
Acting Manager, Small Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E7-15581 Filed 8-10-07; 8:45 am]
BILLING CODE 4910-13-P