[Federal Register: October 3, 2007 (Volume 72, Number 191)]
[Rules and Regulations]
[Page 56256-56258]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr03oc07-6]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2007-27595; Directorate Identifier 2006-NM-248-AD;
Amendment 39-15216; AD 2007-20-06]
RIN 2120-AA64
Airworthiness Directives; Saab Model SAAB 2000 Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: We are adopting a new airworthiness directive (AD) for the
products listed above. This AD results from mandatory continuing
airworthiness information (MCAI) originated by an aviation authority of
another country to identify and correct an unsafe condition on an
aviation product. The MCAI describes the unsafe condition as:
It has been revealed that the control surface balancing
procedure in the * * * SAAB 2000 SRM (structural repair manual) * *
* is incorrect.
Incorrect balance, outside the tolerance of the aileron control
surface, may lead to vibrations that in [the] worst case can result
in flutter.
We are issuing this AD to require actions to correct the unsafe
condition on these products.
DATES: This AD becomes effective November 7, 2007.
The Director of the Federal Register approved the incorporation by
reference of a certain publication listed in this AD as of November 7,
2007.
ADDRESSES: You may examine the AD docket on the Internet at http://dms.dot.gov
or in person at the U.S. Department of Transportation,
Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200
New Jersey, Avenue, SE., Washington, DC.
FOR FURTHER INFORMATION CONTACT: Mike Borfitz, Aerospace Engineer,
International Branch, ANM-116, FAA, Transport Airplane Directorate,
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425)
227-2677; fax (425) 227-1149.
SUPPLEMENTARY INFORMATION:
Discussion
We issued a notice of proposed rulemaking (NPRM) to amend 14 CFR
part 39 to include an AD that would apply to the specified products.
That NPRM was published in the Federal Register on March 16, 2007 (72
FR 12576). That NPRM proposed to correct an unsafe condition for the
specified products. The MCAI states:
It has been revealed that the control surface balancing
procedure in the Web and CD/DVD versions of the SAAB 2000 SRM
(structural repair manual) Chapter 51-60-00, Control Surface
Balancing Procedure is incorrect. The incorrect Calculation formula
(page 1, 4 and 7) was incorporated in Revision 21 of the SRM dated
April 01/05 and was distributed in 4 July 2005 on the CD/DVD issue
Apr. 01/05.
In the incorrect formula, an ``x'' (multiplication) has been
replaced with a ``+'' (addition) when the data was converted in the
system and if this formula is followed, you may receive a result
outside of the allowed tolerance.
Incorrect balance, outside the tolerance of the aileron control
surface, may lead to vibrations that in [the] worst case can result
in flutter.
The hard copy of the manual, SAAB 2000 SRM, is correct.
The CD/DVD dated Oct 01/05, marked ``Reissue'', includes a
correct SAAB SRM revision 22.
The corrective action includes identifying ailerons that have been
balanced after July 4, 2005. If balanced incorrectly, they must be
rebalanced.
Comments
We gave the public the opportunity to participate in developing
this AD. We considered the comments received.
Request To Withdraw the NPRM
Saab points out that at the time European Aviation Safety Agency
(EASA) issued Emergency Airworthiness Directive 2006-0053-E, dated
February 22, 2006 (the MCAI), the hard copy of the structural repair
manual (SRM) was correct but the Web and CD/DVD versions had an
incorrect calculation formula. At that time, the FAA did not issue an
emergency AD because there were only 3 of the affected airplanes
operating in the U.S. and the
[[Page 56257]]
operators stated that they had not used the incorrect formula. The rest
of the affected fleet was operating in Europe and subject to the EASA
Emergency AD. SAAB AB states that this means that no affected airplane
is operating with a rigging performed according to the incorrect
formula. Saab recommends that we withdraw the NPRM and do not issue the
AD.
We disagree with the request to withdraw the NPRM. The number of
affected airplanes of U.S. registry has grown from 3 to 7 in the past
year, a growth trend that could continue. We cannot be certain that all
airplanes that are placed on the U.S. Register have had the ailerons
balanced correctly. Issuance of this AD will ensure that airplanes will
be in compliance before being permitted to operate in the U.S. We have
revised the Costs of Compliance paragraph of this AD to reflect the
current number of U.S.-registered airplanes. We have made no other
change to the AD in this regard.
Request To Refer to Later Revisions of the CD/DVD
Saab requests that we change the following phrase from paragraph
(e) of the NPRM: ``The CD/DVD dated Oct 01/05, marked `Reissue',
includes a correct SAAB SRM revision 22.'' Saab states that the SRM has
been revised a couple of times since the MCAI was issued, and that
revision 23 and higher of the SRM have the correct formula.
We acknowledge that revision 23 and higher of the SRM also have the
correct formula. However, we have not revised the text in paragraph (e)
of the AD because that text is simply a direct quote from the MCAI. We
have not changed the AD in this regard.
Conclusion
We reviewed the available data, including the comments received,
and determined that air safety and the public interest require adopting
the AD as proposed.
Differences Between This AD and the MCAI or Service Information
We have reviewed the MCAI and related service information and, in
general, agree with their substance. But we might have found it
necessary to use different words from those in the MCAI to ensure the
AD is clear for U.S. operators and is enforceable. In making these
changes, we do not intend to differ substantively from the information
provided in the MCAI and related service information.
We might also have required different actions in this AD from those
in the MCAI in order to follow our FAA policies. Any such differences
are highlighted in a NOTE within the AD.
Costs of Compliance
Based on the service information, we estimate that this AD affects
about 7 products of U.S. registry. We also estimate that it takes about
1 work-hour per product to identify ailerons that have been balanced
after July 4, 2005. The average labor rate is $80 per work-hour. Based
on these figures, we estimate the cost of the AD for U.S. operators to
be $560, or $80 per product.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's
authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, Part A, Subpart III, Section 44701: General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We determined that this AD will not have federalism implications
under Executive Order 13132. This AD will not have a substantial direct
effect on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government.
For the reasons discussed above, I certify this AD:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this AD and placed it in the AD docket.
Examining the AD Docket
You may examine the AD docket on the Internet at http://dms.dot.gov
; or in person at the Docket Operations office between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays. The AD
docket contains the NPRM, the regulatory evaluation, any comments
received, and other information. The street address for the Docket
Operations office (telephone (800) 647-5527) is in the ADDRESSES
section. Comments will be available in the AD docket shortly after
receipt.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
0
Accordingly, under the authority delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new AD:
2007-20-06 Saab Aircraft AB: Amendment 39-15216. Docket No. FAA-
2007-27595; Directorate Identifier 2006-NM-248-AD.
Effective Date
(a) This airworthiness directive (AD) becomes effective November
7, 2007.
Affected ADs
(b) None.
Applicability
(c) This AD applies to Saab Model SAAB 2000 airplanes,
certificated in any category, ranging from serial number -004
through -063, on which aileron, P/N (part number) 7357600-501/502,
P/N 7357600-503/504, P/N 7357600-505/506, P/N 7357600-507/508, P/N
7357991-601/602, P/N 7357991-603/604, P/N 7357991-605/606, P/N
7357995-843/844, or P/N 7357995-927/928, is installed.
Subject
(d) Air Transport Association (ATA) of America Code 57: Wings.
Reason
(e) The mandatory continuing airworthiness information (MCAI)
states:
It has been revealed that the control surface balancing
procedure in the web and CD/DVD versions of the SAAB 2000 SRM
(Structural Repair Manual) Chapter 51-60-00, Control Surface
Balancing Procedure is incorrect. The incorrect Calculation formula
(page 1, 4 and 7) was incorporated in Revision 21 of the SRM dated
April 01/05 and was distributed in 4 July 2005 on the CD/DVD issue
Apr. 01/05.
[[Page 56258]]
In the incorrect formula, an ``x'' (multiplication) has been
replaced with a ``+'' (addition) when the data was converted in the
system and if this formula is followed, you may receive a result
outside of the allowed tolerance.
Incorrect balance, outside the tolerance of the aileron control
surface, may lead to vibrations that in [the] worst case can result
in flutter.
The hard copy of the manual, SAAB 2000 SRM, is correct.
The CD/DVD dated Oct 01/05, marked ``Reissue'', includes a
correct SAAB SRM revision 22.
The corrective action includes identifying ailerons that have been
balanced after July 4, 2005, until the effective date of this AD. If
balanced incorrectly, they must be rebalanced.
Actions and Compliance
(f) Within one month after the effective date of this AD, unless
already done, do the following actions.
(1) Identify ailerons that have been balanced after July 4,
2005. If balanced incorrectly, they must be rebalanced before
further flight in accordance with Saab Service Bulletin 2000-57-040,
dated February 23, 2006.
(2) As of the effective date of this AD, the aileron balancing
procedure contained in the CD/DVD ``Issue Date: Apr 01/05''
including the Saab SAAB 2000 SRM at Revision 21 and the CD/DVD
``Issue Date: Oct 01/05'' including SRM at Revision 22 may not be
used.
FAA AD Differences
Note: This AD differs from the MCAI and/or service information
as follows: No differences.
Other FAA AD Provisions
(g) The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
International Branch, ANM-116, FAA, has the authority to approve
AMOCs for this AD, if requested using the procedures found in 14 CFR
39.19. Send information to ATTN: Mike Borfitz, Aerospace Engineer,
International Branch, ANM-116, Transport Airplane Directorate, FAA,
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone 227-
2677; fax (425) 227-1149. Before using any approved AMOC on any
airplane to which the AMOC applies, notify your appropriate
principal inspector (PI) in the FAA Flight Standards District Office
(FSDO), or lacking a PI, your local FSDO.
(2) Airworthy Product: For any requirement in this AD to obtain
corrective actions from a manufacturer or other source, use these
actions if they are FAA-approved. Corrective actions are considered
FAA-approved if they are approved by the State of Design Authority
(or their delegated agent). You are required to assure the product
is airworthy before it is returned to service.
(3) Reporting Requirements: For any reporting requirement in
this AD, under the provisions of the Paperwork Reduction Act, the
Office of Management and Budget (OMB) has approved the information
collection requirements and has assigned OMB Control Number 2120-
0056.
Related Information
(h) Refer to MCAI European Aviation Safety Agency Emergency
Airworthiness Directive 2006-0053-E, dated February 22, 2006, and
Saab Service Bulletin 2000-57-040, dated February 23, 2006.
Material Incorporated by Reference
(i) You must use Saab Service Bulletin 2000-57-040, dated
February 23, 2006, including Attachment 1, dated April 1, 2006, to
do the actions required by this AD, unless the AD specifies
otherwise.
(1) The Director of the Federal Register approved the
incorporation by reference of this service information under 5
U.S.C. 552(a) and 1 CFR part 51.
(2) For service information identified in this AD, contact Saab
Aircraft AB, SAAB Aircraft Product Support, S-581.88,
Link[ouml]ping, Sweden.
(3) You may review copies at the FAA, Transport Airplane
Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the
National Archives and Records Administration (NARA). For information
on the availability of this material at NARA, call (202) 741-6030,
or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html
.
Issued in Renton, Washington, on September 21, 2007.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E7-19199 Filed 10-2-07; 8:45 am]
BILLING CODE 4910-13-P