[Federal Register: October 24, 2007 (Volume 72, Number 205)]
[Rules and Regulations]
[Page 60240-60243]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr24oc07-7]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2007-27927; Directorate Identifier 2006-NM-182-AD;
Amendment 39-15239; AD 2007-22-03]
RIN 2120-AA64
Airworthiness Directives; Airbus Model A300 Series Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The FAA is adopting a new airworthiness directive (AD) for all
Airbus Model A300 series airplanes. This AD requires revising the
Airworthiness Limitations Section of the Instructions for Continued
Airworthiness to incorporate new limitations for fuel tank systems.
This AD results from fuel system reviews conducted by the manufacturer.
We are issuing this AD to prevent the potential of ignition sources
inside fuel tanks, which, in combination with flammable fuel vapors
caused by latent failures, alterations, repairs, or maintenance
actions, could result in fuel tank explosions and consequent loss of
the airplane.
DATES: This AD becomes effective November 28, 2007.
The Director of the Federal Register approved the incorporation by
reference
[[Page 60241]]
of a certain publication listed in the AD as of November 28, 2007.
ADDRESSES: For service information identified in this AD, contact
Airbus, 1 Rond Point Maurice Bellonte, 31707 Blagnac Cedex, France.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov
; or in person at the Docket Management Facility
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this AD, the regulatory evaluation,
any comments received, and other information. The address for the
Docket Office (telephone 800-647-5527) is the Document Management
Facility, U.S. Department of Transportation, Docket Operations, M-30,
West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE.,
Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT: Tom Stafford, Aerospace Engineer,
International Branch, ANM-116, FAA, Transport Airplane Directorate,
1601 Lind Avenue SW., Renton, Washington 98057-3356; telephone (425)
227-1622; fax (425) 227-1149.
SUPPLEMENTARY INFORMATION:
Discussion
The FAA issued a notice of proposed rulemaking (NPRM) to amend 14
CFR part 39 to include an AD that would apply to all Airbus A300 series
airplanes. That NPRM was published in the Federal Register on April 20,
2007 (72 FR 19823). That NPRM proposed to require revising the
Airworthiness Limitations Section (ALS) of the Instructions for
Continued Airworthiness to incorporate new limitations for fuel tank
systems.
Actions Since NPRM Was Issued
After we issued the NPRM, Airbus published the A300 Fuel
Airworthiness Limitations, Document 95A.1928/05, Issue 2, dated May 11,
2007 (approved by the European Aviation Safety Agency (EASA) on July 6,
2007) (hereafter referred to as ``Document 95A.1928/05''). In the NPRM,
we referred to Issue 1 of Document 95A.1928/05, dated December 19,
2005, as the appropriate source of service information for
accomplishing the actions proposed in the NPRM. The fuel airworthiness
limitations (FALs) specified in Issue 2 of Document 95A.1928/05 are the
same as those in Issue 1 of Document 95A.1928/05. Airbus has revised
certain task titles in Section 1 of Issue 2 of Document 95A.1928/05 and
has clarified the applicability and corrected certain airplane
maintenance manual (AMM) references in Section 2 of the document.
Therefore, we have revised this AD by referring to Issue 2 of Document
95A.1928/05 as the appropriate source of service information.
After we issued the NPRM, EASA issued airworthiness directive 2007-
0094 R1 dated May 2, 2007, to correct certain compliance times; our
NPRM included the correct compliance times, which we explained as
differences between the NPRM and EASA airworthiness directive 2006-
0200, dated July 11, 2006. The compliance times in this AD already
correspond with the compliance times of EASA airworthiness directive
2007-0094 R1. Therefore, we have revised paragraph (k) of this AD to
refer to EASA airworthiness directive 2007-0094 R1.
After we issued the NPRM, Airbus published Operator Information
Telex (OIT) SE 999.0079/07, Revision 01, dated August 14, 2007, to
identify the applicable sections of the Airbus A300 AMM necessary for
accomplishing the tasks specified in Section 1 of Document 95A.1928/05.
We have added a note to paragraph (f) of this AD to refer to that OIT.
Comments
We provided the public the opportunity to participate in the
development of this AD. We have considered the comments received.
Request To Clarify the Initial Compliance Time
TradeWinds Airlines requests that we revise paragraph (f) of the
NPRM to clarify that the ``INTERVAL'' values specified in Section 1 of
Document 95A.1928/05 are also the initial threshold values. The
commenter states that it is unclear whether the initial compliance
times are the interval values.
We agree that the values specified in the ``INTERVAL'' column of
the ``MAINTENANCE/INSPECTION TASKS'' table in Section 1 of Document
95A.1928/05 should be used as the initial compliance time, as well as
the repetitive interval. We have also clarified the compliance time in
paragraph (f) of this AD by adding the word ``thereafter'' to more
clearly state that `` * * * the repetitive inspections must be
accomplished thereafter * * *.''
Request To Revise ``Relevant Service Information'' Section
Airbus requests that we revise the ``Relevant Service Information''
section to state that ``Section 1, `Maintenance/Inspection Tasks,' of
Document 95A.1928/05 describes certain FAL inspections, which are
periodic inspections of certain features for latent failures that could
contribute to a fire.'' In the NPRM, we specified that the latent
failures could contribute to an ignition source. As justification,
Airbus states that not all three tasks identified in Section 1 of
Document 95A.1928/05 contribute to minimizing the risk of an ignition
source: Only Task 3 minimizes the risk of an ignition source, while
Tasks 1 and 2 minimize the occurrence of a combustible environment. We
agree with Airbus's statements. However, we have not revised this AD in
this regard since the ``Relevant Service Information'' section is not
retained in a final rule.
Request To Revise the Unsafe Condition
Airbus states that it does not agree that there is an unsafe
condition on Model A300 series airplanes, prior to accomplishing the
maintenance/inspection tasks in Section 1 of Document 95A.1928/05.
Airbus agrees that performing these tasks contributes to minimizing the
risk of either an ignition source (Task 3) or the occurrence of a
combustible environment (Tasks 1 and 2). In regard to the critical
design configuration control limitations (CDCCLs), Airbus states that
no unsafe condition exists at delivery, and that no unsafe condition
will develop provided that operators observe the CDCCLs after delivery.
Airbus further states that the CDCCLs are introduced to reduce the risk
that an operator may inadvertently alter the design or installation,
thus introducing a less safe configuration.
We infer Airbus would like us to revise the unsafe condition in
this AD to incorporate its comments. We do not agree to revise the
unsafe condition of this AD. Fuel airworthiness limitations (FALs) are
items arising from a systems safety analysis that have been shown to
have failure modes associated with an unsafe condition, as defined in
FAA Memorandum 2003-112-15, ``SFAR 88--Mandatory Action Decision
Criteria,'' dated February 25, 2003. These FALs are identified in
failure conditions for which an unacceptable probability of ignition
risk could exist if specific tasks or practices or both are not
performed in accordance with a manufacturer's requirements. As Airbus
notes, if an operator does not observe the CDCCLs after delivery, then
an unsafe condition could occur. For this reason we must mandate
Document 95A.1928/05 to ensure the CDCCLs are observed. We have not
changed this AD in this regard.
[[Page 60242]]
Requests To Clarify the Requirements of Paragraph (h)
Airbus requests that we revise paragraph (h) of the NPRM to state
that operators are required to update their internal procedures and
documentation to ensure appropriate management and control of the
CDCCLs specified in Section 2 of Document 95A.1928/05. Airbus states
that paragraph (h) of the NPRM is unclear about what an operator is
expected to do with the CDCCLs. Airbus further states that paragraph
(h) of the NPRM tells operators to add the CDCCLs to the ALS, but
Airbus states that it has already done so for operators. Airbus also
states that the ALS is part of the type certification (TC)
documentation and is not changed by operators. TradeWinds Airlines
requests that we provide guidance as to what is acceptable for
compliance with the requirements of paragraph (h) of the NPRM.
TradeWinds Airlines states that simply listing the CDCCLs in a
maintenance schedule would have little or no effect on preserving
critical ignition source prevention features. The commenter further
states that the Airbus A300 AMM would be the source of the approved
data for accomplishing the tasks related to the CDCCLs, and that
revisions to the AMM would be sufficient for providing instruction to
retain the critical ignition source prevention features.
Although we understand Airbus's concerns and welcome any feedback
that would improve the readability or usability of an AD, the suggested
language is too vague to be legally enforceable, so we cannot use it in
this AD. We understand that Airbus has revised its airworthiness
limitations document. However, according to section 39.7 of the Federal
Aviation Regulations (14 CFR 39.7), no person may operate a product
unless the requirements of an applicable AD have been met. The burden
is placed on the operator, not on the manufacturer, to ensure that the
requirements of an AD are met. The requirement, as stated in the NPRM,
is for the operator to revise its copy of the airworthiness limitations
document. This ensures that each affected operator maintains a current
copy of the required airworthiness limitations.
Concerning Airbus's statement that paragraph (h) of the NPRM does
not clearly specify what an operator is expected to with the CDCCLs, we
clarify that paragraph (h) requires affected operators to revise their
copies of the airworthiness limitations document to include the CDCCL
requirements. This is the only requirement imposed under this AD for
CDCCLs; once this revision has been accomplished, compliance with
paragraph (h) of this AD has been completed. Subsequently, section
91.403(c) of the Federal Aviation Regulations (14 CFR 91.403(c))
requires an affected operator to comply with the revised Airworthiness
Limitations document. Ensuring that one's maintenance program and the
actions of its maintenance personnel are in accordance with the
Airworthiness Limitations is required, but not by the AD. According to
14 CFR 91.403(c), no person may operate an aircraft for which
airworthiness limitations have been issued unless those limitations
have been complied with. Therefore, there is no need to further expand
the requirements of the AD beyond that which was proposed because 14
CFR 91.403(c) already imposes the appropriate required action after the
airworthiness limitations are revised. We have not changed this AD in
this regard.
Request To Cite Airbus ALS Part 5
Airbus disagrees with the statement that it has not yet published a
document titled, ``Airbus ALS Part 5, Fuel Airworthiness Limitations,''
for Model A300 series airplanes. We made that statement in the
``Clarification of Service Information'' section of the NPRM. Airbus
acknowledges that Document 95A.1928/05 has not yet been written in the
ALS Part 5 format, but that it intends to do so after Issue 2 of
Document 95A.1928/05 has been approved. Airbus states that EASA
airworthiness directive 2007-0094 R1 correctly refers to Document
95A.1928/05, since that document contains the actual limitations.
We infer that Airbus requests we revise paragraphs (f) and (h) of
this AD to incorporate the information in `` * * * Airbus ALS Part 5,
Fuel Airworthiness Limitations, as defined in Airbus A300 Fuel
Airworthiness Limitations, Document 95A.1928/05. * * *'' We agree that
the relevant fuel airworthiness limitations are specified in Document
95A.1928/05. In review of the service information Airbus has published
on-line, we could not find any document titled ``Airbus ALS Part 5,
Fuel Airworthiness Limitations.'' The Office of the Federal Register
(OFR) requires that we incorporate by reference all the documents that
are necessary for accomplishing the requirements of this AD. Further,
we are required to cite the document title exactly as it appears on the
document. Since the limitations are in Document 95A.1928/05, we do not
need to refer to Airbus ALS Part 5. We have not changed this AD in this
regard.
Conclusion
We have carefully reviewed the available data, including the
comments received, and determined that air safety and the public
interest require adopting the AD with the changes described previously.
We have determined that these changes will neither increase the
economic burden on any operator nor increase the scope of the AD.
Costs of Compliance
This AD affects about 30 airplanes of U.S. registry. The required
actions take about 2 work hours per airplane, at an average labor rate
of $80 per work hour. Based on these figures, the estimated cost of the
AD for U.S. operators is $4,800, or $160 per airplane.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We have determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866;
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities
[[Page 60243]]
under the criteria of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this AD and placed it in the AD docket. See the ADDRESSES
section for a location to examine the regulatory evaluation.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
0
Accordingly, under the authority delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The Federal Aviation Administration (FAA) amends Sec. 39.13 by
adding the following new airworthiness directive (AD):
2007-22-03 Airbus: Amendment 39-15239. Docket No. FAA-2007-27927;
Directorate Identifier 2006-NM-182-AD.
Effective Date
(a) This AD becomes effective November 28, 2007.
Affected ADs
(b) None.
Applicability
(c) This AD applies to all Airbus Model A300 series airplanes,
certificated in any category, except Airbus Model A300-600 series
airplanes.
Note 1: This AD requires revisions to certain operator
maintenance documents to include new inspections and critical design
configuration control limitations (CDCCLs). Compliance with the
operator maintenance documents is required by 14 CFR 91.403(c). For
airplanes that have been previously modified, altered, or repaired
in the areas addressed by these inspections and CDCCLs, the operator
may not be able to accomplish the inspections and CDCCLs described
in the revisions. In this situation, to comply with 14 CFR
91.403(c), the operator must request approval for an alternative
method of compliance according to paragraph (j) of this AD. The
request should include a description of changes to the required
inspections and CDCCLs that will preserve the critical ignition
source prevention feature of the affected fuel system.
Unsafe Condition
(d) This AD results from fuel system reviews conducted by the
manufacturer. We are issuing this AD to prevent potential of
ignition sources inside fuel tanks, which, in combination with
flammable fuel vapors caused by latent failures, alterations,
repairs, or maintenance actions, could result in fuel tank
explosions and consequent loss of the airplane.
Compliance
(e) You are responsible for having the actions required by this
AD performed within the compliance times specified, unless the
actions have already been done.
Revise Airworthiness Limitations Section (ALS) To Incorporate Fuel
Maintenance and Inspection Tasks
(f) Within 3 months after the effective date of this AD, revise
the ALS of the Instructions for Continued Airworthiness to
incorporate Airbus A300 Fuel Airworthiness Limitations, Document
95A.1928/05, Issue 2, dated May 11, 2007 (approved by the European
Aviation Safety Agency (EASA) on July 6, 2007), Section 1,
``Maintenance/Inspection Tasks.'' For all tasks identified in
Section 1 of Document 95A.1928/05, the initial compliance times
start from the later of the times specified in paragraphs (f)(1) and
(f)(2) of this AD, and the repetitive inspections must be
accomplished thereafter at the intervals specified in Section 1 of
Document 95A.1928/05, except as provided by paragraph (g) of this
AD.
(1) The effective date of this AD.
(2) The date of issuance of the original French standard
airworthiness certificate or the date of issuance of the original
French export certificate of airworthiness.
Note 2: Airbus Operator Information Telex SE 999.0079/07,
Revision 01, dated August 14, 2007, identifies the applicable
sections of the Airbus A300 airplane maintenance manual necessary
for accomplishing the tasks specified in Section 1 of Document
95A.1928/05.
Initial Compliance Time for Task 28-18-00-03-1
(g) For Task 28-18-00-03-1 identified in Section 1 of Document
95A.1928/05, ``Maintenance/Inspection Tasks,'' of Airbus A300 Fuel
Airworthiness Limitations, Document 95A.1928/05, Issue 2, dated May
11, 2007 (approved by the EASA on July 6, 2007): The initial
compliance time is the later of the times specified in paragraphs
(g)(1) and (g)(2) of this AD. Thereafter, Task 28-18-00-03-1 must be
accomplished at the repetitive interval specified in Section 1 of
Document 95A.1928/05.
(1) Prior to the accumulation of 40,000 total flight hours.
(2) Within 72 months or 20,000 flight hours after the effective
date of this AD, whichever occurs first.
Revise ALS To Incorporate CDCCLs
(h) Within 12 months after the effective date of this AD, revise
the ALS of the Instructions for Continued Airworthiness to
incorporate Airbus A300 Fuel Airworthiness Limitations, Document
95A.1928/05, Issue 2, dated May 11, 2007 (approved by the EASA on
July 6, 2007), Section 2, ``Critical Design Configuration Control
Limitations.''
No Alternative Inspections, Inspection Intervals, or CDCCLs
(i) Except as provided by paragraph (j) of this AD: After
accomplishing the actions specified in paragraphs (f) and (h) of
this AD, no alternative inspections, inspection intervals, or CDCCLs
may be used.
Alternative Methods of Compliance (AMOCs)
(j)(1) The Manager, International Branch, ANM-116, Transport
Airplane Directorate, FAA, has the authority to approve AMOCs for
this AD, if requested in accordance with the procedures found in 14
CFR 39.19.
(2) To request a different method of compliance or a different
compliance time for this AD, follow the procedures in 14 CFR 39.19.
Before using any approved AMOC on any airplane to which the AMOC
applies, notify your appropriate principal inspector (PI) in the FAA
Flight Standards District Office (FSDO), or lacking a PI, your local
FSDO.
Related Information
(k) EASA airworthiness directive 2007-0094 R1, dated May 2,
2007, also addresses the subject of this AD.
Material Incorporated by Reference
(l) You must use Airbus A300 Fuel Airworthiness Limitations,
Document 95A.1928/05, Issue 2, dated May 11, 2007, to perform the
actions that are required by this AD, unless the AD specifies
otherwise. The Director of the Federal Register approved the
incorporation by reference of this document in accordance with 5
U.S.C. 552(a) and 1 CFR part 51. Contact Airbus, 1 Rond Point
Maurice Bellonte, 31707 Blagnac Cedex, France, for a copy of this
service information. You may review copies at the FAA, Transport
Airplane Directorate, 1601 Lind Avenue SW., Renton, Washington; or
at the National Archives and Records Administration (NARA). For
information on the availability of this material at NARA, call 202-
741-6030, or go to: http://www.archives.gov/federal-register/cfr/ibr-locations.html
.
Issued in Renton, Washington, on October 15, 2007.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E7-20820 Filed 10-23-07; 8:45 am]
BILLING CODE 4910-13-P