[Federal Register: November 27, 2007 (Volume 72, Number 227)]
[Proposed Rules]
[Page 66085-66087]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr27no07-36]
========================================================================
Proposed Rules
Federal Register
________________________________________________________________________
This section of the FEDERAL REGISTER contains notices to the public of
the proposed issuance of rules and regulations. The purpose of these
notices is to give interested persons an opportunity to participate in
the rule making prior to the adoption of the final rules.
========================================================================
[[Page 66085]]
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 25
[Docket No. NM385; Notice No. 25-07-17-SC]
Special Conditions: Boeing Model 757 Series Airplanes; Seats With
Non-Traditional, Large, Non-Metallic Panels
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed special conditions.
-----------------------------------------------------------------------
SUMMARY: This action proposes special conditions for Boeing Model 757
series airplanes. These airplanes, as modified by Triad International
Maintenance Company (TIMCO), will have a novel or unusual design
feature(s) associated with seats that include non-traditional, large,
non-metallic panels that would affect survivability during a post-crash
fire event. The applicable airworthiness regulations do not contain
adequate or appropriate safety standards for this design feature. These
proposed special conditions contain the additional safety standards
that the Administrator considers necessary to establish a level of
safety equivalent to that established by the existing airworthiness
standards.
DATES: We must receive your comments by December 12, 2007.
ADDRESSES: You must mail two copies of your comments to: Federal
Aviation Administration, Transport Airplane Directorate, Attn: Rules
Docket (ANM-113), Docket No. NM385, 1601 Lind Avenue, SW., Renton,
Washington 98057-3356. You may deliver two copies to the Transport
Airplane Directorate at the above address. You must mark your comments:
Docket No. NM385. You can inspect comments in the Rules Docket
weekdays, except Federal holidays, between 7:30 a.m. and 4 p.m.
FOR FURTHER INFORMATION CONTACT: Dan Jacquet, FAA, Airframe/Cabin
Safety Branch, ANM-115, Transport Airplane Directorate, Aircraft
Certification Service, 1601 Lind Avenue, SW., Renton, Washington 98057-
3356; telephone (425) 227-2676; facsimile (425) 227-1232; electronic
mail daniel.jacquet@faa.gov.
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite interested people to take part in this rulemaking by
sending written comments, data, or views. The most helpful comments
reference a specific portion of the special conditions, explain the
reason for any recommended change, and include supporting data. We ask
that you send us two copies of written comments.
We will file in the docket all comments we receive, as well as a
report summarizing each substantive public contact with FAA personnel
concerning these special conditions. You can inspect the docket before
and after the comment closing date. If you wish to review the docket in
person, go to the address in the ADDRESSES section of this preamble
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays.
We will consider all comments we receive on or before the closing
date for comments. We will consider comments filed late if it is
possible to do so without incurring expense or delay. We may change
these special conditions based on the comments we receive.
If you want the FAA to acknowledge receipt of your comments on this
proposal, include with your comments a pre-addressed, stamped postcard
on which the docket number appears. We will stamp the date on the
postcard and mail it back to you.
Background
On July 31, 2007, Triad International Maintenance Company (TIMCO),
623 Radar Road, Greensboro, North Carolina 27410, applied for a
supplemental type certificate for installing seats that include non-
traditional, large, non-metallic panels in a Boeing Model 757 series
airplane. The Boeing Model 757 series airplanes, currently approved
under Type Certificate No. A2NM, are swept-wing, conventional tail,
twin-engine, turbofan-powered, single aisle, medium-sized transport
category airplanes.
The applicable regulations to airplanes currently approved under
Type Certificate No. A2NM do not require seats to meet the more
stringent flammability standards required of large, non-metallic panels
in the cabin interior. At the time the applicable rules were written,
seats were designed with a metal frame covered by fabric, not with
large, non-metallic panels. Seats also met the then recently adopted
standards for flammability of seat cushions. With the seat design being
mostly fabric and metal, the contribution to a fire in the cabin had
been minimized and was not considered a threat. For these reasons,
seats did not need to be tested to heat release and smoke emission
requirements.
Seat designs have now evolved to occasionally include non-
traditional, large, non-metallic panels. Taken in total, the surface
area of these panels is on the same order as the sidewall and overhead
stowage bin interior panels. To provide the level of passenger
protection intended by the airworthiness standards, these non-
traditional, large, non-metallic panels in the cabin must meet the
standards of Title 14 Code of Federal Regulations (CFR), part 25,
Appendix F, parts IV and V, heat release and smoke emission
requirements.
Type Certification Basis
Under the provisions of 14 CFR 21.101, TIMCO must show that the
Boeing Model 757 series airplanes, as changed, continue to meet the
applicable provisions of the regulations incorporated by reference in
Type Certificate No. A2NM, or the applicable regulations in effect on
the date of application for the change. The regulations incorporated by
reference in the type certificate are commonly referred to as the
``original type certification basis.'' The regulations incorporated by
reference in Type Certificate No. A2NM are as follows:
For Model 757-200 airplanes--part 25, as amended by
Amendment 25-1 through Amendment 25-45. In addition, an equivalent
safety finding exists with respect to Sec. 25.853(c), Compartment
interiors.
For Model 757-300 airplanes--part 25, as amended by
Amendment 25-1 through Amendment 25-85 with the exception listed:
Section 25.853(d)(3), Compartment interiors, at Amendment 25-72.
In addition, the certification basis includes certain special
conditions,
[[Page 66086]]
exemptions, or later amended sections of the applicable part that are
not relevant to these proposed special conditions.
If the Administrator finds that the applicable airworthiness
regulations (i.e., part 25) do not contain adequate or appropriate
safety standards for the Boeing Model 757 series airplanes because of a
novel or unusual design feature, special conditions are prescribed
under the provisions of Sec. 21.16.
In addition to the applicable airworthiness regulations and special
conditions, the Boeing Model 757 series airplanes must comply with the
fuel vent and exhaust emission requirements of 14 CFR part 34 and the
noise certification requirements of 14 CFR part 36.
The FAA issues special conditions, as defined in Sec. 11.19, under
Sec. 11.38 and they become part of the type certification basis under
Sec. 21.101.
Special conditions are initially applicable to the model for which
they are issued. Should the applicant apply for a supplemental type
certificate to modify any other model included on the same type
certificate to incorporate the same or similar novel or unusual design
feature, the special conditions would also apply to the other model
under Sec. 21.101.
Novel or Unusual Design Features
The Boeing Model 757 series airplanes will incorporate the
following novel or unusual design features: These models offer interior
arrangements that include passenger seats that incorporate non-
traditional, large, non-metallic panels in lieu of the traditional
metal frame covered by fabric. The flammability properties of these
panels have been shown to significantly affect the survivability of the
cabin in the case of fire. These seats are considered a novel design
for transport category airplanes that include Amendment 25-61 and
Amendment 25-66 in the certification basis, and were not considered
when those airworthiness standards were established.
The existing regulations do not provide adequate or appropriate
safety standards for seat designs that incorporate non-traditional,
large, non-metallic panels in their designs. In order to provide a
level of safety that is equivalent to that afforded to the balance of
the cabin, additional airworthiness standards, in the form of special
conditions, are necessary. These special conditions supplement Sec.
25.853. The requirements contained in these special conditions consist
of applying the identical test conditions required of all other large
panels in the cabin, to seats with non-traditional, large, non-metallic
panels.
Definition of ``Non-Traditional, Large, Non-Metallic Panel''
A non-traditional, large, non-metallic panel, in this case, is
defined as a panel with exposed-surface areas greater than 1.5 square
feet installed per seat place. The panel may consist of either a single
component or multiple components in a concentrated area. Examples of
parts of the seat where these non-traditional panels are installed
include, but are not limited to: Seat backs, bottoms and leg/foot
rests, kick panels, back shells, credenzas and associated furniture.
Examples of traditional exempted parts of the seat include: Arm caps,
armrest close-outs such as end bays and armrest-styled center consoles,
food trays, video monitors, and shrouds.
Clarification of ``Exposed''
``Exposed'' is considered to include panels that are directly
exposed to the passenger cabin in the traditional sense, and panels
that are enveloped, such as by a dress cover. Traditional fabrics or
leathers currently used on seats are excluded from these special
conditions. These materials must still comply with Sec. 25.853(a) and
Sec. 25.853(c) if used as a covering for a seat cushion, or Sec.
25.853(a) if installed elsewhere on the seat. Non-traditional, large,
non-metallic panels covered with traditional fabrics or leathers will
be tested without their coverings or covering attachments.
Discussion
In the early 1980s the FAA conducted extensive research on the
effects of post-crash flammability in the passenger cabin. As a result
of this research and service experience, we adopted new standards for
interior surfaces associated with large surface area parts.
Specifically, the rules require measurement of heat release and smoke
emission (part 25, Appendix F, parts IV and V) for the affected parts.
Heat release has been shown to have a direct correlation with post-
crash fire survival time. Materials that comply with the standards
(i.e., Sec. 25.853 entitled ``Compartment interiors'' as amended by
Amendment 25-61 and Amendment 25-66) extend survival time by
approximately 2 minutes over materials that do not comply.
At the time these standards were written the potential application
of the requirements of heat release and smoke emission to seats was
explored. The seat frame itself was not a concern because it was
primarily made of aluminum and there were only small amounts of non-
metallic materials. It was determined that the overall effect on
survivability was negligible, whether or not the food trays met the
heat release and smoke requirements. The requirements therefore did not
address seats. The preambles to both the Notice of Proposed Rule Making
(NPRM), Notice No. 85-10 (50 FR 15038, April 16, 1985) and the Final
Rule at Amendment 25-61 (51 FR 26206, July 21, 1986), specifically note
that seats were excluded ``because the recently-adopted standards for
flammability of seat cushions will greatly inhibit involvement of the
seats.''
Subsequently, the Final Rule at Amendment 25-83 (60 FR 6615, March
6, 1995) clarified the definition of minimum panel size: ``It is not
possible to cite a specific size that will apply in all installations;
however, as a general rule, components with exposed-surface areas of
one square foot or less may be considered small enough that they do not
have to meet the new standards. Components with exposed-surface areas
greater than two square feet may be considered large enough that they
do have to meet the new standards. Those with exposed-surface areas
greater than one square foot, but less than two square feet, must be
considered in conjunction with the areas of the cabin in which they are
installed before a determination could be made.''
In the late 1990s, the FAA issued Policy Memorandum 97-112-39,
Guidance for Flammability Testing of Seat/Console Installations,
October 17, 1997 (http://rgl.faa.gov). That memo was issued when it
became clear that seat designs were evolving to include large, non-
metallic panels with surface areas that would impact survivability
during a cabin fire event, comparable to partitions or galleys. The
memo noted that large surface area panels must comply with heat release
and smoke emission requirements, even if they were attached to a seat.
If the FAA had not issued such policy, seat designs could have been
viewed as a loophole to the airworthiness standards that would result
in an unacceptable decrease in survivability during a cabin fire event.
In October of 2004, an issue was raised regarding the appropriate
flammability standards for passenger seats that incorporated non-
traditional, large, non-metallic panels in lieu of the traditional
metal covered by fabric. The Seattle Aircraft Certification Office and
Transport Standards Staff reviewed this design and determined that it
represented the kind and quantity of material that should be required
to pass the heat release and smoke emissions
[[Page 66087]]
requirements. We have determined that special conditions would be
promulgated to apply the standards defined in Sec. 25.853(d) to seats
with large, non-metallic panels in their design.
Applicability
As discussed above, these special conditions are applicable to
Boeing Model 757 series airplanes. It is not our intent, however, to
require seats with large, non-metallic panels to meet Sec. 25.853,
Appendix F, parts IV and V, if they are installed in cabins of
airplanes that otherwise are not required to meet these standards.
Because the heat release and smoke testing requirements of Sec. 25.853
per Appendix F, parts IV and V, are not part of the type certification
basis of the Model 757, these special conditions are only applicable if
the Model 757 series airplanes are in 14 CFR part 121 operations.
Section 121.312 requires compliance with the heat release and smoke
testing requirements of Sec. 25.853, for certain airplanes,
irrespective of the type certification bases of those airplanes. For
Model 757 series airplanes, these are the airplanes that would be
affected by these special conditions. Should TIMCO apply at a later
date for a supplemental type certificate to modify any other model
included on Type Certificate No. A2NM to incorporate the same novel or
unusual design feature, the special conditions would apply to that
model as well.
Conclusion
This action affects only certain novel or unusual design features
on one model series of airplanes. It is not a rule of general
applicability and it affects only the applicant who applied to the FAA
for approval of these features on the airplane.
List of Subjects in 14 CFR Part 25
Aircraft, Aviation safety, Reporting and recordkeeping
requirements.
The authority citation for these special conditions is as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701, 44702, 44704.
The Proposed Special Conditions
Accordingly, the Federal Aviation Administration (FAA) proposes the
following special conditions as part of the type certification basis
for Boeing Model 757 series airplanes modified by TIMCO.
1. Except as provided in paragraph 3 of these special conditions,
compliance with Title 14 CFR part 25, Appendix F, parts IV and V, heat
release and smoke emission, is required for seats that incorporate non-
traditional, large, non-metallic panels that may either be a single
component or multiple components in a concentrated area in their
design.
2. The applicant may designate up to and including 1.5 square feet
of non-traditional, non-metallic panel material per seat place that
does not have to comply with special condition Number 1, above. A
triple seat assembly may have a total of 4.5 square feet excluded on
any portion of the assembly (e.g., outboard seat place 1 square foot,
middle 1 square foot, and inboard 2.5 square feet).
3. Seats do not have to meet the test requirements of Title 14 CFR
part 25, Appendix F, parts IV and V, when installed in compartments
that are not otherwise required to meet these requirements. Examples
include:
a. Airplanes with passenger capacities of 19 or less,
b. Airplanes that do not have Sec. 25.853, Amendment 25-61 or
later, in their certification basis and do not need to comply with the
requirements of 14 CFR Sec. 121.312, and
c. Airplanes exempted from Sec. 25.853, Amendment 25-61 or later.
Issued in Renton, Washington, on November 19, 2007.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E7-23079 Filed 11-26-07; 8:45 am]
BILLING CODE 4910-13-P