[Federal Register: December 14, 2007 (Volume 72, Number 240)]
[Proposed Rules]
[Page 71089-71091]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr14de07-14]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2007-0294; Directorate Identifier 2007-CE-087-AD]
RIN 2120-AA64
Airworthiness Directives; Piaggio Aero Industries S.p.A. Model P
180 Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: We propose to adopt a new airworthiness directive (AD) for the
products listed above. This proposed AD results from mandatory
continuing airworthiness information (MCAI) originated by an aviation
authority of another country to identify and correct an unsafe
condition on an aviation product. The MCAI describes the unsafe
condition as:
Due to pressurization loads, the fuselage frame of the emergency
exit door could suffer from fatigue and develop cracks in its
corners. The superseded Italian Airworthiness Directive (AD) 1995-
059 was issued to require modification of the emergency door frame
in accordance with Piaggio (at the time I.A.M. Rinaldo Piaggio
S.p.A.) Service Bulletin 80-0057 original issue.
Parts necessary to carry out the modification were a new door
pan assembly and a doubler; Since these parts are no longer
available, Piaggio Aero Industries S.p.A. (PAI) designed new
suitable part numbers introduced by Revision 1 of Service Bulletin
80-0057. The present AD mandates modification of the fuselage
emergency door frame in accordance with Revision 1 of Service
Bulletin 80-0057 from PAI.
The proposed AD would require actions that are intended to address the
unsafe condition described in the MCAI.
DATES: We must receive comments on this proposed AD by January 14,
2008.
ADDRESSES: You may send comments by any of the following methods:
Federal eRulemaking Portal: Go to http://www.regulations.gov.
Follow the instructions for submitting comments.
Fax: (202) 493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue, SE., Washington, DC 20590.
Hand Delivery: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m.,
Monday through Friday, except Federal holidays.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov
; or in person at the Docket Management Facility
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this proposed AD, the regulatory
evaluation, any comments received, and other information. The street
address for the Docket Office (telephone (800) 647-5527) is in the
ADDRESSES section. Comments will be available in the AD docket shortly
after receipt.
FOR FURTHER INFORMATION CONTACT: Sarjapur Nagarajan, Aerospace
Engineer, FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas
City, Missouri 64106; telephone: (816) 329-4145; fax: (816) 329-4090.
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to send any written relevant data, views, or
arguments about this proposed AD. Send your comments to an address
listed under the ADDRESSES section. Include ``Docket No. FAA-2007-****;
Directorate Identifier 2007-CE-087-AD'' at the beginning of your
comments. We specifically invite comments on the overall regulatory,
economic, environmental, and energy aspects of this proposed AD. We
will consider all comments received by the closing date and may amend
this proposed AD because of those comments.
We will post all comments we receive, without change, to http://www.regulations.gov
, including any personal information you provide. We
will also post a report summarizing each substantive verbal contact we
receive about this proposed AD.
Discussion
The European Aviation Safety Agency (EASA), which is the Technical
Agent
[[Page 71090]]
for the Member States of the European Community, has issued AD No.:
2007-0225, dated August 14, 2007 (referred to after this as ``the
MCAI''), to correct an unsafe condition for the specified products.
The MCAI states:
Due to pressurization loads, the fuselage frame of the emergency
exit door could suffer from fatigue and develop cracks in its
corners. The superseded Italian Airworthiness Directive (AD) 1995-
059 was issued to require modification of the emergency door frame
in accordance with Piaggio (at the time I.A.M. Rinaldo Piaggio
S.p.A.) Service Bulletin 80-0057 original issue.
Parts necessary to carry out the modification were a new door
pan assembly and a doubler; Since these parts are no longer
available, Piaggio Aero Industries S.p.A. (PAI) designed new
suitable part numbers introduced by Revision 1 of Service Bulletin
80-0057.
The present AD mandates modification of the fuselage emergency
door frame in accordance with Revision 1 of Service Bulletin 80-0057
from PAI.
The MCAI requires the modification of the fuselage frame of the
emergency door, using the newly designed door pan assembly and doubler
and following Piaggio Aero Industries S.p.A. Mandatory Service Bulletin
N. 80-0057, Revision 1, dated May 31, 2007.
You may obtain further information by examining the MCAI in the AD
docket.
Relevant Service Information
Piaggio Aero Industries S.p.A. has issued Mandatory Service
Bulletin N. 80-0057, Revision 1, dated May 31, 2007. The actions
described in this service information are intended to correct the
unsafe condition identified in the MCAI.
FAA's Determination and Requirements of the Proposed AD
This product has been approved by the aviation authority of another
country, and is approved for operation in the United States. Pursuant
to our bilateral agreement with this State of Design Authority, they
have notified us of the unsafe condition described in the MCAI and
service information referenced above. We are proposing this AD because
we evaluated all information and determined the unsafe condition exists
and is likely to exist or develop on other products of the same type
design.
Differences Between This Proposed AD and the MCAI or Service
Information
We have reviewed the MCAI and related service information and, in
general, agree with their substance. But we might have found it
necessary to use different words from those in the MCAI to ensure the
AD is clear for U.S. operators and is enforceable. In making these
changes, we do not intend to differ substantively from the information
provided in the MCAI and related service information.
We might also have proposed different actions in this AD from those
in the MCAI in order to follow FAA policies. Any such differences are
highlighted in a NOTE within the proposed AD.
Costs of Compliance
Based on the service information, we estimate that this proposed AD
would affect about 31 products of U.S. registry. We also estimate that
it would take about 70 work-hours per product to comply with the basic
requirements of this proposed AD. The average labor rate is $80 per
work-hour. Required parts would cost about $14,105 per product.
Based on these figures, we estimate the cost of the proposed AD on
U.S. operators to be $610,855, or $19,705 per product.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's
authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, Part A, Subpart III, Section 44701: General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this proposed AD and placed it in the AD docket.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. The FAA amends Sec. 39.13 by adding the following new AD:
Piaggio Aero Industries S.p.A.: Docket No. FAA-2007-0294;
Directorate Identifier 2007-CE-087-AD.
Comments Due Date
(a) We must receive comments by January 14, 2008.
Affected ADs
(b) None.
Applicability
(c) This AD applies to PIAGGIO P-180 airplanes, manufacturer
serial numbers (MSN) 1001, 1002, 1004, and MSN 1006 through 1033,
that:
(1) are certificated in any category; and
(2) have not been modified in accordance with Piaggio Aero
Industries Service Bulletin No. 80-0057, dated February 7, 1995.
Subject
(d) Air Transport Association of America (ATA) Code 53:
Fuselage.
Reason
(e) The mandatory continuing airworthiness information (MCAI)
states:
Due to pressurization loads, the fuselage frame of the emergency
exit door could suffer from fatigue and develop cracks in its
corners. The superseded Italian Airworthiness Directive (AD) 1995-
059 was issued to require modification of the emergency door frame
in accordance with Piaggio (at the time I.A.M. Rinaldo Piaggio
S.p.A.) Service Bulletin 80-0057 original issue.
[[Page 71091]]
Parts necessary to carry out the modification were a new door
pan assembly and a doubler; Since these parts are no longer
available, Piaggio Aero Industries S.p.A. (PAI) designed new
suitable part numbers introduced by Revision 1 of Service Bulletin
80-0057.
The present AD mandates modification of the fuselage emergency
door frame in accordance with Revision 1 of Service Bulletin 80-0057
from PAI.
The MCAI requires the modification of the fuselage frame of the
emergency door, using the newly designed door pan assembly and
doubler, following Piaggio Aero Industries S.p.A. SB 80-0057,
Revision 1, dated May 31, 2007.
Actions and Compliance
(f) Unless already done, replace the emergency exit door pan
assembly part number (P/N) 80-111152-401 with a new door pan
assembly P/N 80-111152-405, and a new doubler reinforcement P/N 80-
111604-001, following Piaggio Aero Industries S.p.A. Mandatory
Service Bulletin N. 80-0057, Revision 1, dated May 31, 2007, at
whichever of the following occurs later:
(i) When the airplane reaches 4,500 hours total time-in-service
(TIS); or
(ii) Within 6 months after the effective date of this AD or 500
hours TIS after the effective date of this AD, whichever of these
occurs first.
FAA AD Differences
Note: This AD differs from the MCAI and/or service information
as follows: No differences.
Other FAA AD Provisions
(g) The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
Standards Office, FAA, has the authority to approve AMOCs for this
AD, if requested using the procedures found in 14 CFR 39.19. Send
information to ATTN: Sarjapur Nagarajan, Aerospace Engineer, FAA,
Small Airplane Directorate, 901 Locust, Room 301, Kansas City,
Missouri 64106; telephone: (816) 329-4145; fax: (816) 329-4090.
Before using any approved AMOC on any airplane to which the AMOC
applies, notify your appropriate principal inspector (PI) in the FAA
Flight Standards District Office (FSDO), or lacking a PI, your local
FSDO.
(2) Airworthy Product: For any requirement in this AD to obtain
corrective actions from a manufacturer or other source, use these
actions if they are FAA-approved. Corrective actions are considered
FAA-approved if they are approved by the State of Design Authority
(or their delegated agent). You are required to assure the product
is airworthy before it is returned to service.
(3) Reporting Requirements: For any reporting requirement in
this AD, under the provisions of the Paperwork Reduction Act (44
U.S.C. 3501, et seq.), the Office of Management and Budget (OMB) has
approved the information collection requirements and has assigned
OMB Control Number 2120-0056.
Related Information
(h) Refer to MCAI European Aviation Safety Agency AD No.: 2007-
0225, dated August 14, 2007; and Piaggio Aero Industries S.p.A.
Mandatory Service Bulletin N. 80-0057, Revision 1, dated May 31,
2007, for related information.
Issued in Kansas City, Missouri, on December 10, 2007.
John R. Colomy,
Acting Manager, Small Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E7-24216 Filed 12-13-07; 8:45 am]
BILLING CODE 4910-13-P