[Federal Register: December 17, 2007 (Volume 72, Number 241)]
[Proposed Rules]
[Page 71279-71281]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr17de07-20]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2007-0349; Directorate Identifier 2007-CE-094-AD]
RIN 2120-AA64
Airworthiness Directives; EADS SOCATA Model TBM 700 Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: We propose to adopt a new airworthiness directive (AD) for the
products listed above that would supersede an existing AD. This
proposed AD results from mandatory continuing airworthiness information
(MCAI) originated by an aviation authority of another country to
identify and correct an unsafe condition on an aviation product. The
MCAI describes the unsafe condition as:
A non-respect of the pilot door adjustment procedure could have
damaged the stop fitting and could result in a consequent
depressurization of the airplane.
The proposed AD would require actions that are intended to address the
unsafe condition described in the MCAI.
DATES: We must receive comments on this proposed AD by January 16,
2008.
ADDRESSES: You may send comments by any of the following methods:
Federal eRulemaking Portal: Go to http://www.regulations.gov.
Follow the instructions for submitting comments.
Fax: (202) 493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue, SE., Washington, DC 20590.
Hand Delivery: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m.,
Monday through Friday, except Federal holidays.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov
; or in person at the Docket Management Facility,
U.S. Department of Transportation, Docket Operations, M-30, West
Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE.,
Washington, DC 20590.
Docket Management Facility between 9 a.m. and 5 p.m., Monday
through Friday, except Federal holidays. The AD docket contains this
proposed AD, the regulatory evaluation, any comments received, and
other information. The street address for the Docket Office (telephone
(800) 647-5527) is in the ADDRESSES section. Comments will be available
in the AD docket shortly after receipt.
FOR FURTHER INFORMATION CONTACT: Albert J. Mercado, Aerospace Engineer,
FAA, Small Airplane Directorate, 901 Locust, Room 301, Kansas City,
Missouri 64106; telephone: (816) 329-4119; facsimile: (816) 329-4090.
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to send any written relevant data, views, or
arguments about this proposed AD. Send your comments to an address
listed under the ADDRESSES section. Include ``Docket No. FAA-2007-0349;
Directorate Identifier 2007-CE-094-AD'' at the beginning of your
comments. We specifically invite
[[Page 71280]]
comments on the overall regulatory, economic, environmental, and energy
aspects of this proposed AD. We will consider all comments received by
the closing date and may amend this proposed AD because of those
comments.
We will post all comments we receive, without change, to http://regulations.gov
, including any personal information you provide. We
will also post a report summarizing each substantive verbal contact we
receive about this proposed AD.
Discussion
On February 6, 2007, we issued AD 2007-04-08, Amendment 39-14939
(72 FR 7559 February 16, 2007). That AD required actions intended to
address an unsafe condition on the products listed above.
Since we issued AD 2007-04-08, EADS SOCATA TBM Aircraft Mandatory
Service Bulletin SB 70-131, Amendment 1, dated June 2007, was issued,
which adds a procedure in the replacement of the stop fittings.
The Direction g[eacute]n[eacute]rale de l'aviation civile (DGAC),
which is the aviation authority for France, has issued AD No. F-2007-
016, October 10, 2007 (referred to after this as ``the MCAI''), to
correct an unsafe condition for the specified products. The MCAI
states:
A non-respect of the pilot door adjustment procedure could have
damaged the stop fitting and could result in a consequent
depressurization of the airplane.
This proposed AD requires you to inspect the pilot door locking stop
fittings for correct length and replace any incorrect length pilot door
locking stop fittings found.
You may obtain further information by examining the MCAI in the AD
docket.
Relevant Service Information
EADS SOCATA has issued TBM Aircraft Mandatory Service Bulletin SB
70-131, Amendment 1, dated June 2007. The actions described in this
service information are intended to correct the unsafe condition
identified in the MCAI.
FAA's Determination and Requirements of the Proposed AD
This product has been approved by the aviation authority of another
country, and is approved for operation in the United States. Pursuant
to our bilateral agreement with this State of Design Authority, they
have notified us of the unsafe condition described in the MCAI and
service information referenced above. We are proposing this AD because
we evaluated all information and determined the unsafe condition exists
and is likely to exist or develop on other products of the same type
design.
Differences Between This Proposed AD and the MCAI or Service
Information
We have reviewed the MCAI and related service information and, in
general, agree with their substance. But we might have found it
necessary to use different words from those in the MCAI to ensure the
AD is clear for U.S. operators and is enforceable. In making these
changes, we do not intend to differ substantively from the information
provided in the MCAI and related service information.
We might also have proposed different actions in this AD from those
in the MCAI in order to follow FAA policies. Any such differences are
highlighted in a NOTE within the proposed AD.
Costs of Compliance
Based on the service information, we estimate that this proposed AD
would affect about 157 products of U.S. registry. We also estimate that
it would take about 4.5 work-hours per product to comply with the basic
requirements of this proposed AD. The average labor rate is $80 per
work-hour. Required parts would cost about $15 per product. Based on
these figures, we estimate the cost of the proposed AD on U.S.
operators to be $58,875, or $375 per product.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's
authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, Part A, Subpart III, Section 44701: General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this proposed AD and placed it in the AD docket.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. The FAA amends Sec. 39.13 by removing Amendment 39-14939 (72 FR
7559, February 16, 2007), and adding the following new AD:
EADS SOCATA: Docket No. FAA-2007-0349; Directorate Identifier 2007-
CE-094-AD.
Comments Due Date
(a) We must receive comments by January 16, 2008.
Affected ADs
(b) AD 2007-04-08, Amendment 39-14939.
Applicability
(c) This AD applies to Model TBM 700 airplanes, serial numbers
126 through 322, that are:
(1) equipped with a pilot door; and
(2) certificated in any category.
Subject
(d) Air Transport Association of America (ATA) Code 53:
Fuselage.
Reason
(e) The mandatory continuing airworthiness information (MCAI)
states:
[[Page 71281]]
A non-respect of the pilot door adjustment procedure could have
damaged the stop fitting and could result in a consequent
depressurization of the airplane.
This AD requires you to inspect the pilot door locking stop fittings
for correct length and replace any incorrect length pilot door
locking stop fittings found.
Requirements Retained From AD 2007-04-08
(f) Unless already done, inspect the pilot door locking stop-
fittings for correct length within 30 days after March 23, 2007 (the
effective date of AD 2007-04-08). Do the inspection following EADS
SOCATA TBM Aircraft Mandatory Service Bulletin SB 70-131, dated July
2005, or EADS SOCATA TBM Aircraft Mandatory Service Bulletin SB 70-
131, Amendment 1, dated June 2007.
New Requirements of This AD: Actions and Compliance
(g) Do the following actions, unless already done:
(1) Any incorrect length pilot door locking stop-fittings
replaced following the inspection required in paragraph (f) of this
AD in accordance with AD 2007-04-08, using the original issue of
EADS SOCATA TBM Aircraft Mandatory Service Bulletin SB 70-131, dated
July 2005, must be replaced again within the next 12 months after
the effective date of this AD. Do the replacement using EADS SOCATA
TBM Aircraft Mandatory Service Bulletin SB 70-131, Amendment 1,
dated June 2007.
(2) Any incorrect length pilot door locking stop-fittings found
during the inspection required in paragraph (f) of this AD and not
previously replaced in accordance with AD 2007-04-08, must be
replaced before further flight. Do the replacement using EADS SOCATA
TBM Aircraft Mandatory Service Bulletin SB 70-131, Amendment 1,
dated June 2007.
FAA AD Differences
Note: This AD differs from the MCAI and/or service information
as follows: No differences.
Other FAA AD Provisions
(h) The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
Standards Office, FAA, has the authority to approve AMOCs for this
AD, if requested using the procedures found in 14 CFR 39.19. Send
information to ATTN: Albert Mercado, Aerospace Engineer, FAA, Small
Airplane Directorate, 901 Locust, Room 301, Kansas City, Missouri
64106; telephone: (816) 329-4119; fax: (816) 329-4090. Before using
any approved AMOC on any airplane to which the AMOC applies, notify
your appropriate principal inspector (PI) in the FAA Flight
Standards District Office (FSDO), or lacking a PI, your local FSDO.
(2) Airworthy Product: For any requirement in this AD to obtain
corrective actions from a manufacturer or other source, use these
actions if they are FAA-approved. Corrective actions are considered
FAA-approved if they are approved by the State of Design Authority
(or their delegated agent). You are required to assure the product
is airworthy before it is returned to service.
(3) Reporting Requirements: For any reporting requirement in
this AD, under the provisions of the Paperwork Reduction Act (44
U.S.C. 3501 et seq.), the Office of Management and Budget (OMB) has
approved the information collection requirements and has assigned
OMB Control Number 2120-0056.
Special Flight Permit
(i) If you have ordered parts and they are not available, then
you may fly unpressurized until parts become available or for a
period not to exceed 90 days after the inspection required in
paragraph (f) of this AD, whichever occurs first. You must also
fabricate and install a placard as described below. Completing the
action of paragraph (g)(2) of this AD terminates the placard
requirement.
(1) Fabricate (using letters at least 1/8 inch in height) a
warning placard that states ``This airplane is prohibited from
pressurized flight.''
(2) Install the placard in full view of the pilot. The owner/
operator holding at least a private pilot certificate as authorized
by section 43.7 of the Federal Aviation Regulations (14 CFR 43.7)
may install the placard as required in paragraph (h) of this AD.
Related Information
(j) Refer to MCAI Direction generale de l'aviation civile (DGAC)
AD No. F-2007-016, October 10, 2007; and EADS SOCATA TBM Aircraft
Mandatory Service Bulletin SB 70-131, Amendment 1, dated June 2007,
for related information.
Issued in Kansas City, Missouri, on December 11, 2007.
John R. Colomy,
Acting Manager, Small Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E7-24321 Filed 12-14-07; 8:45 am]
BILLING CODE 4910-13-P