[Federal Register: January 9, 2007 (Volume 72, Number 5)]
[Rules and Regulations]
[Page 889-892]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr09ja07-3]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2005-22696; Directorate Identifier 2005-SW-22-AD;
Amendment 39-14877; AD 2007-01-06]
RIN 2120-AA64
Airworthiness Directives; Bell Helicopter Textron Canada Model
206A, B, L, L-1, L-3, and L-4 Helicopters
AGENCY: Federal Aviation Administration, DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: This amendment supersedes an existing airworthiness directive
(AD) for the specified Bell Helicopter Textron Canada (BHTC) model
helicopters. The existing AD currently requires certain inspections and
checks of the tail rotor blade (blade) for a deformation, a crack, and
a bent or deformed tail rotor weight (weight). Also, that AD requires,
before further flight, replacing each blade with an airworthy blade if
a deformation, a crack, or a bent or deformed weight is found. This
action contains the same actions as the existing AD and also adds to
the applicability certain serial-numbered blades inadvertently omitted
from the current AD. This action also requires replacing each affected
blade, which is a terminating action. This amendment is prompted by
three reports of skin cracks originating near the blade trailing edge
balance weight. The actions specified by this AD are intended to
prevent blade failure and subsequent loss of control of the helicopter.
DATES: Effective February 13, 2007.
ADDRESSES: You may get the service information identified in this AD
from Bell Helicopter Textron Canada, 12,800 Rue de l'Avenir, Mirabel,
Quebec J7J1R4, telephone (450) 437-2862 or (800) 363-8023, fax (450)
433-0272.
Examining the Docket
You may examine the docket that contains this AD, any comments, and
other information on the Internet at http://dms.dot.gov, or at the
Docket Management System (DMS), U.S. Department of Transportation, 400
Seventh Street, SW., Room PL-401, on the plaza level of the Nassif
Building, Washington, DC.
FOR FURTHER INFORMATION CONTACT: Sharon Miles, Aviation Safety
Engineer, FAA, Rotorcraft Directorate, Regulations and Guidance Group,
Fort Worth, Texas 76193-0111, telephone (817) 222-5122, fax (817) 222-
5961.
SUPPLEMENTARY INFORMATION: A proposal to amend 14 CFR part 39 by
superseding AD 2004-24-08, Amendment 39-13884 (69 FR 69810, December 1,
2004), for the specified BHTC model helicopters was published in the
Federal Register on October 17, 2005 (70 FR 60246). This action
contains the same actions as the existing AD. Also, when we issued AD
2004-24-08, we intentionally did not include the long-term requirement
(no later than April 27, 2007) for removing and sending the affected
blades to Rotor Blades, Inc. as specified by the manufacturer. We are
including a long-term requirement in this AD that the affected blades
be replaced on or before April 27, 2007, as terminating action.
Additionally, in AD 2004-24-08, we inadvertently omitted blade serial
numbers 10102 through 10114 from the applicability. We are correcting
that oversight with this action.
Since issuing AD 2004-24-08, BHTC has issued Alert Service Bulletin
206-04-100 for Bell Model 206A and B helicopters, and 206L-04-127 for
Bell Model 206L series helicopters, both Revision C, both dated March
5, 2005 (ASB). These ASBs add two warnings in the compliance section
specifying returning the blade for balancing to Rotor Blades, Inc., and
introduce new skin damage limits that supersede the previous damage
limits. The ASB also gives a new address for Rotor Blades Inc.
Transport Canada, the airworthiness authority for Canada, notified
the FAA that an unsafe condition may exist on these helicopter models.
Transport Canada advises of three reports of skin cracks originating
near the blade trailing edge balance weight. Two of the occurrences
caused a loss of the weight and a strip of material along the trailing
edge leading to an imbalance, which caused the fracture of three of the
four tail rotor gearbox attachments. One of these occurrences resulted
in the gearbox shifting that caused failure of the drive shaft and
resulting loss of yaw control. Transport Canada issued AD No. CF-2004-
05R1, dated June 28, 2004, to ensure the continued airworthiness of
these helicopters in Canada.
These helicopter models are manufactured in Canada and are type
certificated for operation in the United States under the provisions of
14 CFR 21.29 and the applicable bilateral agreement. Pursuant to the
applicable bilateral agreement, Transport Canada has kept the FAA
informed of the situation described above. The FAA has examined the
findings of Transport Canada, reviewed all available information, and
determined that AD action is necessary for products of these type
designs that are certificated for operation in the United States.
Interested persons have been afforded an opportunity to participate
in the making of this amendment. No comments were received on the
proposal or the FAA's determination of the cost to the public. The FAA
has determined that air safety and the public interest require the
adoption of the rule as proposed, except for a change in paragraph (f)
of the AD to add additional contact information. This change will
neither increase the economic burden on any operator nor increase the
scope of the AD.
The FAA estimates that this AD will:
Affect 2194 helicopters of U.S. registry,
Take about \1/4\ work hour for a blade check or
inspection, and
Take 3 work hours to replace a blade at an average labor
rate of $65 per work hour.
Cost about $5848 per helicopter. (In its ASB, the
manufacturer states it will give warranty credit based on hour usage on
the blade with remaining life hours and other restrictions.)
Based on these figures, we estimate the total cost impact of the AD
on U.S. operators to be $19,989,973. Costs assume--200 pilot checks, 26
mechanic inspections, and one blade replacement for 90 percent of the
fleet with a nonconforming blade.
Regulatory Findings
We have determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on
[[Page 890]]
the States, on the relationship between the national Government and the
States, or on the distribution of power and responsibilities among the
various levels of government.
For the reasons discussed above, I certify that the regulation:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared an economic evaluation of the estimated costs to comply
with this AD. See the DMS to examine the economic evaluation.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
Adoption of the Amendment
0
Accordingly, pursuant to the authority delegated to me by the
Administrator, the Federal Aviation Administration amends part 39 of
the Federal Aviation Regulations (14 CFR part 39) as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. Section 39.13 is amended by removing Amendment 39-13884 (69 FR
69810, December 1, 2004) and by adding a new airworthiness directive
(AD), Amendment 39-14877, to read as follows:
2007-01-06 Bell Helicopter Textron Canada: Amendment 39-14877.
Docket No. FAA-2005-22696; Directorate Identifier 2005-SW-22-AD.
Supersedes AD 2004-24-08, Amendment 39-13884, Docket No. 2004-SW-12-
AD.
Applicability
Model 206A, B, L, L-1, L-3, and L-4 helicopters, with a tail
rotor blade (blade) with the following part number (P/N) and serial
number (S/N) installed, certificated in any category.
----------------------------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------------------------
Model 206A & B; Blade, P/N 206-016- Model 206A, B, L, L-1, L-3, & L-4; Blade, P/N 206-016-201-131, S/N with
201-133, S/N with prefix ``CS'' and prefix ``CS'' and no ``V'' suffix
no ``V'' suffix
----------------------------------------------------------------------------------------------------------------
1381 through 1442 7000 through 7018 10174 through 10218
1492 through 1517 7020 through 7043 10220
1520 through 1542 7045 through 7050 10232
1550 7052 through 7132 10235
1556 7134 through 7246 10237 through 10241
1560 7248 through 7270 10244
1562 7272 through 7277 10245
1564 through 1567 7279 through 7339 10248
1569 through 1606 7342 through 7368 10250 through 10264
1609 7784 10266 through 10268
1611 7786 10270 through 10274
1612 7788 10276 through 10278
1614 through 1631 7790 through 7796 10280 through 10282
1633 through 1675 7798 through 7819 10284 through 10292
1677 7821 through 7833 10296
1678 7835 through 7839 10300 through 10330
1680 through 1682 7841 through 8001 10332
1684 through 1787 8003 through 8026 10333
1789 through 1803 8029 through 8061 10335 through 10347
1810 through 1812 8064 through 8117 10349
1814 8119 10351 through 10359
1816 8121 through 8139 10363 through 10365
1820 8142 through 8176 10367
1823 through 1831 8178 through 8262 10373
1834 through 1836 8264 through 8294 10374
1838 8298 through 8368 10377 through 10385
1840 through 1844 8370 through 8375 10387 through 10408
1846 8378 through 8416 10410
1848 through 1882 8419 10414 through 10417
1884 through 1887 8421 10419 through 10427
1889 through 1893 8425 through 8428 10430
1896 through 1898 8430 through 8438 10432
1900 8440 10437
1904 8441 10438
1909 through 1912 8443 10442 through 10445
1915 8445 through 8447 10458 through 10466
1916 8449 through 8606 10469
1919 through 1921 8608 through 8622 10470
[[Page 891]]
1924 8624 through 8626 10474
1928 through 1931 8628 through 8632 10476 through 10478
1933 8635 through 8653 10480 through 10487
1934 through 1939 8655 through 8686 10489 through 10491
1943 8690 10493 through 10495
1945 8692 through 8700 10497 through 10503
1947 8703 through 8715 10505 through 10588
1948 8717 through 8722 10591 through 10606
1952 through 1957 8724 through 8742 10608 through 10610
1960 8745 through 8828 10612 through 10620
1962 through 1965 8830 through 8835 10623
8838 through 8840 10624
8842 through 8881 10631 through 10655
8883 through 9032 10657 through 10669
9034 through 9139 10672
9141 through 9198 10673
9200 10676 through 10678
9202 through 9302 10680 through 10683
9304 through 9339 10685
9341 through 9371 10687
9373 through 9411 10689 through 10702
9413 10707
9415 through 9417 10712
9419 through 9496 10715
9498 through 9585 10730
9587 through 9594 10732 through 10734
9596 through 9618 10736
9621 through 9629 10738
9632 through 9642 10739
9645 through 9651 10746
9653 through 9673 10750
9675 through 9707 10756
9709 through 9724 10760
9727 through 9731 10761
9733 through 9735 10765
9737 through 9739 10770
9741 through 9748 10774 through 10776
9751 through 9785 10778
9787 10781
9788 10783 through 10785
9790 through 9792 10792
9795 through 9847 10794
9849 through 9928 10798
9930 through 9937 10799
9940 through 9942 10806 through 10808
9944 through 9952 10811
9955 through 9972 10814 through 10822
9974 through 9989 10824
9991 through 9995 10825
9997 through 10004 10829
10006 through 10009 10831
10011 10917
10013 through 10018 10923
10021 through 10030 10931
10034 10936
10036 through 10057 10937
10061 through 10082 10940
10090 through 10092 10943
10094 through 10100 10945
10102 through 10114 10947
10116 10948
10119 10964
10121 10965
10123 through 10134 10973
10136 through 10140 10982
10142 through 10144 10985
10146 through 10172 10986
----------------------------------------------------------------------------------------------------------------
Compliance
Required as indicated.
To prevent blade failure and subsequent loss of control of the
helicopter, do the following:
(a) Before further flight, unless accomplished previously, and
before installing any blade with a P/N and S/N listed in the
applicability section of this AD, clean the blade. Using a 10X or
higher magnifying glass, inspect both sides of each blade for a
deformation, a crack, and a bent or deformed weight in the area
shown in Figure 1 of this AD.
Note 1: Paint irregularities on the blade may indicate a crack.
[[Page 892]]
[GRAPHIC] [TIFF OMITTED] TR09JA07.003
(b) After doing paragraph (a) of this AD, at the following
intervals, clean both sides of each blade and do either paragraph
(1) or (2) as follows:
(1) At intervals not to exceed 12 hours time-in-service (TIS),
using a 10X or higher magnifying glass, inspect both sides of each
blade for a deformation, a crack, and a bent or deformed weight in
the area shown in Figure 1 of this AD, or
(2) Inspect and check both sides of each blade for a
deformation, a crack, and a bent or deformed weight in the area
shown in Figure 1 of this AD as follows:
(i) Using a 10X or higher magnifying glass, inspect at intervals
not to exceed 24 hours TIS, and
(ii) Check at intervals not to exceed 3 hours TIS between the
inspections required by paragraph (b)(2)(i) of this AD. An owner/
operator (pilot), holding at least a private pilot certificate, may
perform this visual check and must enter compliance with this
paragraph into the helicopter maintenance records by following 14
CFR sections 43.11 and 91.417(a)(2)(v).
(c) Before further flight, replace any blade that has a
deformation, a crack, or a bent or deformed weight with an airworthy
blade.
Note 2: Bell Helicopter Textron Alert Service Bulletin No. 206-
04-100 for Model 206A and B and No. 206L-04-127 for Model 206L
series, both Revision C, both dated March 5, 2005, pertain to the
subject of this AD.
(d) On or before April 27, 2007, for any affected part-numbered
blade with a S/N listed in the applicability section of this AD:
(1) Replace the blade with a blade that has a S/N other than one
listed in the applicability section of this AD, or
(2) Replace the blade with a blade that has a S/N listed in the
applicability section of this AD and also has a ``V'' suffix.
(e) Replacing each blade with an airworthy blade as required by
paragraph (d) of this AD constitutes terminating action for the
requirements of this AD.
(f) To request a different method of compliance or a different
compliance time for this AD, follow the procedures in 14 CFR 39.19.
Contact the Safety Management Group, Rotorcraft Directorate, FAA,
ATTN: Sharon Miles, Aviation Safety Engineer, Regulations and
Guidance Group, Fort Worth, Texas 76193-0111, telephone (817) 222-
5122, fax (817) 222-5961, for information about previously approved
alternative methods of compliance.
(g) This amendment becomes effective on February 13, 2007.
Note 3: The subject of this AD is addressed in Transport Canada
(Canada) AD No. CF-2004-05R1, dated June 28, 2004.
Issued in Fort Worth, Texas, on December 26, 2006.
David A. Downey,
Manager, Rotorcraft Directorate, Aircraft Certification Service.
[FR Doc. E7-39 Filed 1-8-07; 8:45 am]
BILLING CODE 4910-13-P