[Federal Register: January 31, 2008 (Volume 73, Number 21)]
[Proposed Rules]
[Page 5770-5773]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr31ja08-20]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2008-0091; Directorate Identifier 2007-NM-311-AD]
RIN 2120-AA64
Airworthiness Directives; Boeing Model 747 Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: We propose to adopt a new airworthiness directive (AD) for
certain Boeing Model 747 airplanes. This proposed AD would require
modification of the refuel valve control unit for the reserve fuel
tanks. This proposed AD would also require a revision to the FAA-
approved maintenance program to incorporate airworthiness limitation
(AWL) No. 28-AWL-20 or AWL No. 28-AWL-25, as applicable. This proposed
AD results from fuel system reviews conducted by the manufacturer. We
are proposing this AD to prevent lightning-induced electrical energy
from entering a reserve fuel tank through the refuel valve, which could
result in a fuel tank explosion and consequent loss of the airplane.
DATES: We must receive comments on this proposed AD by March 17, 2008.
ADDRESSES: You may send comments by any of the following methods:
Federal eRulemaking Portal: Go to http://
www.regulations.gov. Follow the instructions for submitting comments.
Fax: 202-493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue, SE., Washington, DC 20590.
Hand Delivery: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m.,
Monday through Friday, except Federal holidays.
For service information identified in this AD, contact Boeing
Commercial Airplanes, P.O. Box 3707, Seattle, Washington 98124-2207.
Examining the AD Docket
You may examine the AD docket on the Internet at http://
www.regulations.gov; or in person at the Docket Management Facility
between 9 a.m. and 5 p.m., Monday through
[[Page 5771]]
Friday, except Federal holidays. The AD docket contains this proposed
AD, the regulatory evaluation, any comments received, and other
information. The street address for the Docket Office (telephone 800-
647-5527) is in the ADDRESSES section. Comments will be available in
the AD docket shortly after receipt.
FOR FURTHER INFORMATION CONTACT: Sulmo Mariano, Aerospace Engineer,
Propulsion Branch, ANM-140S, FAA, Seattle Aircraft Certification
Office, 1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone
(425) 917-6501; fax (425) 917-6590.
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to send any written relevant data, views, or
arguments about this proposed AD. Send your comments to an address
listed under the ADDRESSES section. Include ``Docket No. FAA-2008-0091;
Directorate Identifier 2007-NM-311-AD'' at the beginning of your
comments. We specifically invite comments on the overall regulatory,
economic, environmental, and energy aspects of this proposed AD. We
will consider all comments received by the closing date and may amend
this proposed AD because of those comments.
We will post all comments we receive, without change, to http://
www.regulations.gov, including any personal information you provide. We
will also post a report summarizing each substantive verbal contact we
receive about this proposed AD.
Discussion
The FAA has examined the underlying safety issues involved in fuel
tank explosions on several large transport airplanes, including the
adequacy of existing regulations, the service history of airplanes
subject to those regulations, and existing maintenance practices for
fuel tank systems. As a result of those findings, we issued a
regulation titled ``Transport Airplane Fuel Tank System Design Review,
Flammability Reduction and Maintenance and Inspection Requirements''
(66 FR 23086, May 7, 2001). In addition to new airworthiness standards
for transport airplanes and new maintenance requirements, this rule
included Special Federal Aviation Regulation No. 88 (``SFAR 88,''
Amendment 21-78, and subsequent Amendments 21-82 and 21-83).
Among other actions, SFAR 88 requires certain type design (i.e.,
type certificate (TC) and supplemental type certificate (STC)) holders
to substantiate that their fuel tank systems can prevent ignition
sources in the fuel tanks. This requirement applies to type design
holders for large turbine-powered transport airplanes and for
subsequent modifications to those airplanes. It requires them to
perform design reviews and to develop design changes and maintenance
procedures if their designs do not meet the new fuel tank safety
standards. As explained in the preamble to the rule, we intended to
adopt airworthiness directives to mandate any changes found necessary
to address unsafe conditions identified as a result of these reviews.
In evaluating these design reviews, we have established four
criteria intended to define the unsafe conditions associated with fuel
tank systems that require corrective actions. The percentage of
operating time during which fuel tanks are exposed to flammable
conditions is one of these criteria. The other three criteria address
the failure types under evaluation: single failures, single failures in
combination with a latent condition(s), and in-service failure
experience. For all four criteria, the evaluations included
consideration of previous actions taken that may mitigate the need for
further action.
We have determined that the actions identified in this AD are
necessary to reduce the potential of ignition sources inside fuel
tanks, which, in combination with flammable fuel vapors, could result
in fuel tank explosions and consequent loss of the airplane.
Boeing has found that it is possible for unsafe energy to enter a
reserve fuel tank through the refuel valve from induced electrical
energy on the unshielded wire during a lightning strike. This
condition, if not corrected, could result in a fuel tank explosion and
consequent loss of the airplane.
Relevant Service Information
We have reviewed Boeing Alert Service Bulletin 747-28A2291, dated
September 27, 2007. The service bulletin describes procedures for
modifying the refuel valve control unit for the reserve fuel tanks. The
modification includes installing a new angle bracket with two grounding
studs, installing bonding ground jumpers between the refuel valve
mounting bolts and the grounding studs, and doing a resistance check.
We have also reviewed the Boeing 747-100/200/300/SP Airworthiness
Limitations (AWLs) and Certification Maintenance Requirements (CMRs),
D6-13747-CMR, Revision January 2007 (hereafter referred to as
``Document D6-13747-CMR''). (For the purposes of Document D6-13747-CMR,
the Model 747SR series airplane is basically a Model 747-100 series
airplane with certain modifications to improve fatigue life.) Section D
of Document D6-13747-CMR describes new AWLs for fuel tank systems. The
AWLs include:
AWL inspections, which are periodic inspections of certain
features for latent failures that could contribute to an ignition
source.
Critical design configuration control limitations
(CDCCLs), which are limitation requirements to preserve a critical
ignition source prevention feature of the fuel tank system design that
is necessary to prevent the occurrence of an unsafe condition. The
purpose of a CDCCL is to provide instruction to retain the critical
ignition source prevention feature during configuration change that may
be caused by alterations, repairs, or maintenance actions. A CDCCL is
not a periodic inspection.
Section D of Document D6-13747-CMR adds new fuel system AWL No. 28-
AWL-20, which is a CDCCL to maintain the design features of the reserve
tank fueling valve controller when the fueling valve controller is
removed and replaced.
We have also reviewed the Boeing 747-400 Maintenance Planning Data
(MPD) Document, D621U400-9, Section 9, Revision 24, dated June 2006
(hereafter referred to as the ``Boeing 747-400 MPD''). Subsection D of
the Boeing 747-400 MPD adds new fuel system AWL No. 28-AWL-25, which is
a CDCCL to maintain the design features of the reserve tank fueling
valve controller when the fueling valve controller is removed and
replaced.
FAA's Determination and Requirements of This Proposed AD
We are proposing this AD because we evaluated all relevant
information and determined the unsafe condition described previously is
likely to exist or develop in other products of the(se) same type
design(s). This proposed AD would require the following actions:
Modification of the refuel valve control unit for the
reserve fuel tanks.
Revision to the FAA-approved maintenance program to
incorporate AWL No. 28-AWL-20, which would require maintaining the
design features of the reserve tank fueling valve controller when the
fueling valve controller is removed and replaced on Model 747-100, 747-
100B, 747-100B SUD, 747-200B, 747-200C, 747-200F, 747-300, 747SR, and
747SP series airplanes.
Revision to the FAA-approved maintenance program to
incorporate
[[Page 5772]]
AWL No. 28-AWL-25, which would require maintaining the design features
of the reserve tank fueling valve controller when the fueling valve
controlled is removed and replaced on Model 747-400, 747-400D, and 747-
400F series airplanes.
This proposed AD would also allow accomplishing the revision to the
AWLs section of the Instructions for Continued Airworthiness in
accordance with later revisions of the MPD as an acceptable method of
compliance if they are approved by the Manager, Seattle Aircraft
Certification Office, FAA.
Costs of Compliance
We estimate that this proposed AD would affect 300 airplanes of
U.S. registry. The following table provides the estimated costs, at an
average labor rate of $80 per hour, for U.S. operators to comply with
this proposed AD.
Estimated Costs
--------------------------------------------------------------------------------------------------------------------------------------------------------
Action Work hours Parts Cost per product Fleet cost
--------------------------------------------------------------------------------------------------------------------------------------------------------
Modification.................... Up to 7..................... Up to $286.................. Up to $846.................. Up to $253,800.
Maintenance program revision.... 1........................... None........................ $80......................... $24,000.
--------------------------------------------------------------------------------------------------------------------------------------------------------
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's
authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, Part A, Subpart III, Section 44701: General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
1. Is not a ``significant regulatory action'' under Executive Order
12866,
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979), and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
You can find our regulatory evaluation and the estimated costs of
compliance in the AD Docket.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. The FAA amends Sec. 39.13 by adding the following new AD:
Boeing: Docket No. FAA-2008-0091; Directorate Identifier 2007-NM-
311-AD.
Comments Due Date
(a) We must receive comments by March 17, 2008.
Affected ADs
(b) None.
Applicability
(c) This AD applies to Boeing Model 747-100, 747-100B, 747-100B
SUD, 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-
400F, 747SR, and 747SP series airplanes, certificated in any
category; as identified in Boeing Alert Service Bulletin 747-
28A2291, dated September 27, 2007.
Note 1: This AD requires revisions to certain operator
maintenance documents to include new inspections. Compliance with
these inspections is required by 14 CFR 91.403(c). For airplanes
that have been previously modified, altered, or repaired in the
areas addressed by these inspections, the operator may not be able
to accomplish the inspections described in the revisions. In this
situation, to comply with 14 CFR 91.403(c), the operator must
request approval for an alternative method of compliance according
to paragraph (h) of this AD. The request should include a
description of changes to the required inspections that will ensure
the continued operational safety of the airplane.
Unsafe Condition
(d) This AD results from fuel system reviews conducted by the
manufacturer. We are issuing this AD to prevent lightning-induced
electrical energy from entering a reserve fuel tank through the
refuel valve, which could result in a fuel tank explosion and
consequent loss of the airplane.
Compliance
(e) Comply with this AD within the compliance times specified,
unless already done.
Modification
(f) Within 60 months after the effective date of this AD, modify
the refuel valve control unit for the reserve fuel tanks, by
accomplishing all of the applicable actions specified in the
Accomplishment Instructions of Boeing Alert Service Bulletin 747-
28A2291, dated September 27, 2007.
Maintenance Program Revision
(g) Concurrently with accomplishing the modification required by
paragraph (f) of this AD, revise the FAA-approved maintenance
program by incorporating the information specified in paragraphs
(g)(1) or (g)(2) of this AD, as applicable.
(1) For Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747-
200C, 747-200F, 747-300, 747SR, and 747SP series airplanes:
Incorporate AWL No. 28-AWL-20 of Section D of the Boeing 747-100/
200/300/SP Airworthiness Limitations (AWLs) and Certification
Maintenance Requirements (CMRs), D6-13747-CMR, Revision January
2007, into the FAA-approved maintenance program. Accomplishing the
revision in accordance with a later revision of Document D6-13747-
CMR is an acceptable method of compliance if the revision is
approved by the Manager, Seattle Aircraft Certification Office
(ACO), FAA.
(2) For Model 747-400, 747-400D, and 747-400F series airplanes:
Incorporate AWL No. 28-AWL-25 of Subsection D of the Boeing 747-400
Maintenance Planning Data (MPD) Document, D621U400-9, Section 9,
Revision 24, dated June 2006, into the FAA-approved maintenance
program. Accomplishing the revision in accordance with a later
revision of the MPD is an acceptable method of compliance if the
revision is approved by the Manager, Seattle ACO, FAA.
[[Page 5773]]
Alternative Methods of Compliance (AMOCs)
(h)(1) The Manager, Seattle ACO, FAA, ATTN: Sulmo Mariano,
Aerospace Engineer, Propulsion Branch, ANM-140S, 1601 Lind Avenue
SW., Renton, Washington 98057-3356; telephone (425) 917-6501; fax
(425) 917-6590; has the authority to approve AMOCs for this AD, if
requested using the procedures found in 14 CFR 39.19.
(2) To request a different method of compliance or a different
compliance time for this AD, follow the procedures in 14 CFR 39.19.
Before using any approved AMOC on any airplane to which the AMOC
applies, notify your appropriate principal inspector (PI) in the FAA
Flight Standards District Office (FSDO), or lacking a PI, your local
FSDO.
Issued in Renton, Washington, on January 18, 2008.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E8-1704 Filed 1-30-08; 8:45 am]
BILLING CODE 4910-13-P