[Federal Register: August 11, 2008 (Volume 73, Number 155)]
[Rules and Regulations]
[Page 46543-46546]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr11au08-6]
[[Page 46543]]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2008-0375; Directorate Identifier 2007-NM-272-AD;
Amendment 39-15627; AD 2008-16-09]
RIN 2120-AA64
Airworthiness Directives; Short Brothers Model SD3-60 Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The FAA is superseding two existing airworthiness directives
(ADs), which apply to all Short Brothers Model SD3-60 airplanes. One of
the ADs currently requires inspection of the welded joints of the
balance weight brackets for the elevator trim tabs for cracking;
repetitive inspections, as applicable; and corrective actions including
the eventual replacement of all brackets. The other AD currently
requires, for certain airplanes, repetitive inspections for cracking of
the balance weight brackets and replacement of any cracked bracket, and
provides for an optional terminating action for the repetitive
inspections. This new AD requires an additional inspection to detect
cracks of the balance weight brackets, applicable related investigative
and corrective actions, and replacement of a certain balance weight
bracket when it has reached its maximum life limit. This AD results
from a report indicating that several reworked balance weight brackets
have exhibited signs of premature failure. We are issuing this AD to
prevent failure of the balance weight brackets of the elevator trim
tabs, which could cause loss of the balance weight. This could result
in incorrect trim during takeoff and landing, and reduced
controllability of the airplane.
DATES: This AD becomes effective September 15, 2008.
The Director of the Federal Register approved the incorporation by
reference of certain publications listed in the AD as of September 15,
2008.
On March 14, 2005 (70 FR 9212, February 25, 2005), the Director of
the Federal Register approved the incorporation by reference of Short
Brothers Alert Service Bulletin SD360-55-A21, dated December 16, 2004.
On August 3, 2004 (69 FR 38813, June 29, 2004), the Director of the
Federal Register approved the incorporation by reference of Short
Brothers Service Bulletin SD360-55-20, dated June 26, 2003.
ADDRESSES: For service information identified in this AD, contact Short
Brothers, Airworthiness & Engineering Quality, P.O. Box 241, Airport
Road, Belfast BT3 9DZ, Northern Ireland.
Examining the AD Docket
You may examine the AD docket on the Internet at http://
www.regulations.gov; or in person at the Docket Management Facility
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this AD, the regulatory evaluation,
any comments received, and other information. The address for the
Docket Office (telephone 800-647-5527) is the Document Management
Facility, U.S. Department of Transportation, Docket Operations, M-30,
West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE.,
Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT: Todd Thompson, Aerospace Engineer,
International Branch, ANM-116, FAA, Transport Airplane Directorate,
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425)
227-1175; fax (425) 227-1149.
SUPPLEMENTARY INFORMATION:
Discussion
The FAA issued a notice of proposed rulemaking (NPRM) to amend 14
CFR part 39 to include an AD that supersedes AD 2004-13-08, amendment
39-13690 (69 FR 38813, June 29, 2004); and AD 2005-04-13, amendment 39-
13985 (70 FR 9212, February 25, 2005). The existing ADs apply to all
Short Brothers Model SD3-60 airplanes. That NPRM was published in the
Federal Register on April 1, 2008 (73 FR 17260). That NPRM proposed to
retain the requirements of the existing ADs. That NPRM also proposed to
require an additional inspection to detect cracks of the balance weight
brackets, applicable related investigative and corrective actions, and
replacement of a certain balance weight bracket when it has reached its
maximum life limit.
Comments
We provided the public the opportunity to participate in the
development of this AD. No comments have been received on the NPRM or
on the determination of the cost to the public.
Conclusion
We have carefully reviewed the available data and determined that
air safety and the public interest require adopting the AD as proposed.
Costs of Compliance
The following table provides the estimated costs for U.S. operators
to comply with this AD.
Estimated Costs
--------------------------------------------------------------------------------------------------------------------------------------------------------
Average Number of
Work labor U.S.-
Action hours rate per Parts Cost per airplane registered Fleet cost
hour airplanes
--------------------------------------------------------------------------------------------------------------------------------------------------------
Inspections (required by AD 2004- 12 $80 (1) $960, per inspection 21 $20,160, per inspection cycle.
13-08). cycle.
Replacement (required by AD 2004- 8 80 $632 $1,272.............. 21 $26,712.
13-08).
Inspections (required by AD 2005- 12 80 (1) $960, per inspection 21 $20,160, per inspection cycle.
04-13). cycle.
Inspection (new required action).. 12 80 (1) $960, per inspection 21 $20,160, per inspection cycle.
cycle.
Replacement (new required action). 8 80 864 $1,504, per 21 $31,584, per replacement cycle.
replacement cycle.
--------------------------------------------------------------------------------------------------------------------------------------------------------
\1\ None.
[[Page 46544]]
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
subtitle VII, part A, subpart III, section 44701, ``General
Requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We have determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866;
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this AD and placed it in the AD docket. See the ADDRESSES
section for a location to examine the regulatory evaluation.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
0
Accordingly, under the authority delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The Federal Aviation Administration (FAA) amends Sec. 39.13 by
removing amendments 39-13690 (69 FR 38813, June 29, 2004), and 39-13985
(70 FR 9212, February 25, 2005), and by adding the following new
airworthiness directive (AD):
2008-16-09 Short Brothers PLC: Amendment 39-15627. Docket No. FAA-
2008-0375; Directorate Identifier 2007-NM-272-AD.
Effective Date
(a) This AD becomes effective September 15, 2008.
Affected ADs
(b) This AD supersedes ADs 2004-13-08 and 2005-04-13.
Applicability
(c) This AD applies to all Short Brothers Model SD3-60
airplanes, certificated in any category.
Unsafe Condition
(d) This AD results from a report indicating that several
reworked balance weight brackets have exhibited signs of premature
failure. We are issuing this AD to prevent failure of the balance
weight bracket of the elevator trim tab, which could cause loss of
the balance weight. This could result in incorrect trim during
takeoff and landing, and reduced controllability of the airplane.
Compliance
(e) You are responsible for having the actions required by this
AD performed within the compliance times specified, unless the
actions have already been done.
Requirements of AD 2004-13-08
Service Bulletin Reference
(f) The term ``service bulletin,'' as used in paragraphs (g)
through (j) of this AD, means the Accomplishment Instructions of
Short Brothers Service Bulletin SD360-55-20, dated June 26, 2003; or
Revision 1, dated June 20, 2005.
Initial Inspection
(g) Within 2 months after August 3, 2004 (the effective date of
AD 2004-13-08): Do a dye penetrant inspection for cracking in the
welded joints of the balance weight brackets for the left and right
elevator trim tabs, in accordance with the service bulletin.
Investigative and Corrective Actions if No Cracking Is Found
(h) If no cracking is found during the inspection required by
paragraph (g) of this AD, do the actions required by paragraphs
(h)(1) and (h)(2) of this AD at the applicable compliance times.
(1) Repeat the inspection required by paragraph (g) of this AD
at intervals not to exceed 4,800 flight hours until the bracket is
replaced per paragraph (h)(2) or (i) of this AD.
(2) Prior to the accumulation of 28,800 total flight hours, or
within 6 months after August 3, 2004, whichever occurs later:
Replace any bracket that has not been replaced per paragraph (i) of
this AD with a new bracket or with a serviceable bracket that has
been inspected in accordance with paragraph (g) of this AD. Replace
in accordance with the service bulletin. Replacement of the brackets
constitutes terminating action for the repetitive inspections
required by paragraph (h)(1) of this AD.
Corrective Actions if Any Cracking Is Found
(i) If any cracking is found during any inspection required by
paragraph (g) or (h) of this AD: Before further flight, accomplish
the applicable action in paragraph (i)(1) or (i)(2) of this AD in
accordance with the service bulletin.
(1) For airplanes that have accumulated less than 28,800 flight
hours and on which all cracking on brackets is less than 0.25 inch
in length: Repair the affected bracket in accordance with part B of
the service bulletin (including the additional dye penetrant
inspection of the repaired welded joint) and repeat the inspection
required by paragraph (g) of this AD at intervals not to exceed
4,800 flight hours; or replace the bracket in accordance with
paragraph (h)(2) of this AD. Replacement of the bracket constitutes
terminating action for the repetitive inspections.
(2) For any airplane on which any cracking on a bracket is 0.25
inch in length or greater, and for any airplane that has accumulated
28,800 flight hours or more on which any cracking of any length is
found on a bracket: Replace the affected bracket with a new bracket
or with a serviceable bracket that has been inspected in accordance
with paragraph (g) of this AD. Replacement of the bracket
constitutes terminating action for the repetitive inspections
required by paragraph (i)(1) of this AD.
Refitting
(j) Before further flight following any inspection per paragraph
(g) or (h) of this AD; or before further flight following repair or
replacement of a bracket per paragraph (h)(2) or (i) of this AD:
Refit the balance weights, covers, and trim tabs, in accordance with
the service bulletin. Where the service bulletin specifies to
contact the manufacturer for disposition of certain conditions while
refitting, obtain further disposition instructions from the Manager,
International Branch, ANM-116, FAA, Transport Airplane Directorate;
or the European Aviation Safety Agency (EASA) (or its delegated
agent).
Parts Installation
(k) As of August 3, 2004, no person may install on any airplane
a balance weight bracket unless the welded joint has been inspected
in accordance with paragraph (g) of this AD.
Requirements of AD 2005-04-13
Service Bulletin Reference
(l) The following information applies to the service bulletin
referenced in paragraphs (l) through (o) of this AD:
(1) The term ``service bulletin,'' as used in paragraphs (l)
through (o) of this AD, means
[[Page 46545]]
the Accomplishment Instructions of Short Brothers Alert Service
Bulletin SD360-55-A21, dated December 16, 2004.
(2) Although the service bulletin specifies to return subject
parts to the manufacturer, this AD does not include that
requirement.
Repetitive Inspections
(m) For airplanes equipped with balance weight brackets of the
elevator trim tabs having part number SD3-07-6011xA, and having a
serial number beginning with ``X3'' or ``X4'': Prior to the
accumulation of 250 flight hours since installation of the subject
balance weight bracket of the elevator trim tab, or within 30 flight
hours after March 14, 2005 (the effective date of AD 2005-04-13),
whichever is later, do a dye penetrant inspection for cracking of
the balance weight brackets for the left and right elevator trim
tabs, in accordance with the service bulletin.
(1) For a balance weight bracket on which no cracking is found:
Do paragraph (o) of this AD, and repeat the inspection thereafter at
intervals not to exceed 250 flight hours until paragraph (n) of this
AD is accomplished.
(2) For a balance weight bracket on which any cracking is found:
Before further flight, replace the bracket with a new or reworked
balance weight bracket that conforms to the approved design standard
in accordance with the service bulletin, and do paragraph (o) of
this AD.
Optional Terminating Action
(n) For airplanes equipped with balance weight brackets of the
elevator trim tabs having part number SD3-07-6011xA, and having a
serial number beginning with ``X3'' or ``X4'': Replacement of any
subject balance weight bracket with a new or reworked balance weight
bracket that conforms to the approved design standard, in accordance
with the service bulletin, constitutes terminating action for the
repetitive inspections required by paragraph (m) of this AD for the
replaced bracket.
Refitting
(o) For airplanes equipped with balance weight brackets of the
elevator trim tabs having part number SD3-07-6011xA, and having a
serial number beginning with ``X3'' or ``X4'': Before further flight
following any inspection or replacement of a bracket in accordance
with paragraphs (m) and (n) of this AD: Refit the balance weights,
covers, and trim tabs, in accordance with the service bulletin.
Where the service bulletin specifies to contact the manufacturer for
disposition of certain conditions while refitting, obtain further
disposition instructions from the Manager, International Branch,
ANM-116, FAA, Transport Airplane Directorate; or the European
Aviation Safety Agency (EASA) (or its delegated agent).
Parts Installation
(p) For all airplanes: As of March 14, 2005, no person may
install, on any airplane subject to this AD, a balance weight
bracket having part number SD3-07-6011xA, and having a serial number
beginning with ``X3'' or ``X4,'' unless the bracket is also marked
``Rework batch number R-Bxxxxx'' (where ``xxxxx'' is a number).
New Requirements of This AD
Inspection(s) and Replacements
(q) For airplanes equipped with balance weight brackets of the
elevator trim tabs having part number SD3-07-6011xA manufactured in
the year 2003 or 2004, including reworked brackets, installed in
accordance with paragraph (h)(2), (i)(2), or (n) of this AD, as
applicable: Do the actions specified in paragraphs (q)(1) and (q)(2)
of this AD in accordance with Parts A and B of the Accomplishment
Instructions of Shorts Alert Service Bulletin SD360-55-A21, Revision
1, dated March 29, 2007.
(1) Within 30 flight hours after the effective date of this AD,
or within 250 flight hours since installation of the balance weight
brackets of the elevator trim tabs or since the last inspection
required by paragraph (g), (h)(1), (i)(1), or (m) of this AD,
whichever occurs later: Do a dye penetrant inspection to detect
cracks of the balance weight brackets of the elevator trim tabs.
(i) If no crack is detected, repeat the dye penetrant inspection
at intervals not to exceed 250 flight hours, until the replacement
required by paragraph (q)(2) of this AD is done.
(ii) If any crack is detected, before further flight, do the
replacement specified in paragraph (q)(2) of this AD.
(2) Before the accumulation of 1,750 flight hours since
installation of the balance weight brackets of the elevator trim
tabs, or within 180 days after the effective date of this AD,
whichever occurs later: Replace the balance weight brackets with new
balance weight brackets manufactured in 2005 or later. Thereafter,
replace any balance weight bracket with a new bracket manufactured
in 2005 or later at intervals not to exceed the accumulation of
1,750 flight hours on that bracket. Accomplishment of the initial
replacement ends the repetitive inspection requirements of this AD.
(r) For airplanes equipped with balance weight brackets of the
elevator trim tabs having part number SD3-31-6213xB inspected in
accordance with paragraph (g), (h)(1), or (i)(1) of this AD and
retained or refitted following approved repair in accordance with
paragraph (j) of this AD: Do the actions specified in paragraphs
(r)(1) and (r)(2) of this AD in accordance with Parts A and B of the
Accomplishment Instructions of Shorts Service Bulletin SD360-55-20,
Revision 2, dated March 29, 2007.
(1) Within 4,800 flight hours since last inspection, or within
180 days after the effective date of this AD, whichever occurs
later, and thereafter at intervals not to exceed 4,800 flight hours:
Do a dye penetrant inspection to detect cracks of the balance weight
brackets of the elevator trim tabs.
(i) If no crack is detected, repeat the dye penetrant inspection
at intervals not to exceed 4,800 flight hours, until the replacement
required by paragraph (r)(2) of this AD is done.
(ii) If any crack is detected, before further flight, do the
replacement specified in paragraph (r)(2) of this AD.
(2) Before the accumulation of 28,800 flight hours since any
balance weight bracket of the elevator trim tabs is new, or within
180 days after the effective date of this AD, whichever occurs
later: Replace the balance weight brackets with new balance weight
brackets manufactured in 2005 or later. Thereafter, replace any
balance weight bracket with a new bracket manufactured in 2005 or
later at intervals not to exceed the accumulation of 28,800 flight
hours on that bracket. Accomplishment of the initial replacement
ends the repetitive inspection requirements of this AD.
Part Installation
(s) For all airplanes: As of the effective date of this AD, no
person may install, on any airplane, a balance weight bracket of the
elevator trim tab manufactured earlier than 2005.
Alternative Methods of Compliance (AMOCs)
(t) The Manager, International Branch, ANM-116, Transport
Airplane Directorate, FAA, has the authority to approve AMOCs for
this AD, if requested using the procedures found in 14 CFR 39.19.
Send information to ATTN: Todd Thompson, Aerospace Engineer,
International Branch, ANM-116, FAA, Transport Airplane Directorate,
1601 Lind Avenue SW., Renton, Washington 98057-3356; telephone (425)
227-1175; fax (425) 227-1149. Before using any approved AMOC on any
airplane to which the AMOC applies, notify your appropriate
principal inspector (PI) in the FAA Flight Standards District Office
(FSDO), or lacking a PI, your local FSDO.
Related Information
(u) European Aviation Safety Agency emergency airworthiness
directive 2007-0107-E, dated April 18, 2007, also addresses the
subject of this AD.
Material Incorporated by Reference
(v) You must use the service bulletins specified in Table 1 of
this AD to perform the actions that are required by this AD, unless
the AD specifies otherwise.
Table 1--Material Incorporated by Reference
----------------------------------------------------------------------------------------------------------------
Service Bulletin Revision level Date
----------------------------------------------------------------------------------------------------------------
Short Brothers Alert Service Bulletin Original........................ December 16, 2004.
SD360-55-A21.
Short Brothers Service Bulletin SD360-55- Original........................ June 26, 2003.
20.
Shorts Alert Service Bulletin SD360-55- Revision 1...................... March 29, 2007.
A21.
Shorts Service Bulletin SD360-55-20...... Revision 1...................... June 20, 2005.
[[Page 46546]]
Shorts Service Bulletin SD360-55-20...... Revision 2...................... March 29, 2007.
----------------------------------------------------------------------------------------------------------------
(1) The Director of the Federal Register approved the
incorporation by reference of Shorts Alert Service Bulletin SD360-
55-A21, Revision 1, dated March 29, 2007; Shorts Service Bulletin
SD360-55-20, Revision 1, dated June 20, 2005; and Shorts Alert
Service Bulletin SD360-55-20, Revision 2, dated March 29, 2007; in
accordance with 5 U.S.C. 552(a) and 1 CFR part 51.
(2) On March 14, 2005 (70 FR 9212, February 25, 2005), the
Director of the Federal Register approved the incorporation by
reference of Short Brothers Alert Service Bulletin SD360-55-A21,
dated December 16, 2004.
(3) On August 3, 2004 (69 FR 38813, June 29, 2004), the Director
of the Federal Register approved the incorporation by reference of
Short Brothers Service Bulletin SD360-55-20, dated June 26, 2003.
(4) Contact Short Brothers, Airworthiness & Engineering Quality,
P.O. Box 241, Airport Road, Belfast BT3 9DZ, Northern Ireland, for a
copy of this service information. You may review copies at the FAA,
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton,
Washington; or at the National Archives and Records Administration
(NARA). For information on the availability of this material at
NARA, call 202-741-6030, or go to: http://www.archives.gov/federal-
register/cfr/ibr-locations.html.
Issued in Renton, Washington, on July 23, 2008.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E8-17744 Filed 8-8-08; 8:45 am]
BILLING CODE 4910-13-P