[Federal Register: August 13, 2008 (Volume 73, Number 157)]
[Rules and Regulations]
[Page 47029-47032]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr13au08-2]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2008-0179; Directorate Identifier 2007-NM-367-AD;
Amendment 39-15572; AD 2008-13-09]
RIN 2120-AA64
Airworthiness Directives; Bombardier Model DHC-8-102, DHC-8-103,
DHC-8-106, DHC-8-201, DHC-8-202, DHC-8-301, DHC-8-311, and DHC-8-315
Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: We are adopting a new airworthiness directive (AD) for the
products listed above. This AD results from mandatory continuing
airworthiness information (MCAI) originated by an aviation authority of
another country to identify and correct an unsafe condition on an
aviation product. The MCAI describes the unsafe condition as:
Bombardier Aerospace has completed a system safety review of the
aircraft fuel system against fuel tank safety standards * * *.
[A]ssessment showed that supplemental maintenance tasks
[inspections of fuel tank bonding jumpers, wiring harnesses, and
drain valve components, among other items and actions; and
applicable corrective actions] are required to prevent potential
ignition sources within the fuel system, which could result in a
fuel tank explosion. * * *
We are issuing this AD to require actions to correct the unsafe
condition on these products.
DATES: This AD becomes effective September 17, 2008.
The Director of the Federal Register approved the incorporation by
reference of certain publications listed in this AD as of September 17,
2008.
ADDRESSES: You may examine the AD docket on the Internet at http://
www.regulations.gov or in person at the U.S. Department of
Transportation, Docket Operations, M-30, West Building Ground Floor,
Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC.
FOR FURTHER INFORMATION CONTACT: Rocco Viselli, Aerospace Engineer,
Airframe and Propulsion Branch, ANE-171, FAA, New York Aircraft
Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New
York 11590; telephone (516) 228-7331; fax (516) 794-5531.
SUPPLEMENTARY INFORMATION:
Discussion
We issued a supplemental notice of proposed rulemaking (NPRM) to
amend 14 CFR part 39 to include an AD that would apply to the specified
products. That supplemental NPRM was published in the Federal Register
on May 1, 2008 (73 FR 23995). That supplemental NPRM proposed to
correct an unsafe condition for the specified products. The MCAI
states:
Bombardier Aerospace has completed a system safety review of the
aircraft fuel system against fuel tank safety standards introduced
in Chapter 525 of the Airworthiness Manual through Notice of
Proposed Amendment (NPA) 2002-043. The identified non-compliances
were then assessed using Transport Canada Policy Letter No. 525-001,
to determine if mandatory corrective action is required.
The assessment showed that supplemental maintenance tasks
[inspections of fuel tank bonding jumpers, wiring harnesses, and
drain valve components, among other items and actions; and
applicable corrective actions] are required to prevent potential
ignition sources within the fuel system, which could result in a
fuel tank explosion. Revisions have been made to Part 2
``Airworthiness Limitations List'' of the
[[Page 47030]]
DHC-8 Maintenance Program Manuals to introduce the required
maintenance tasks.
The corrective action is revising the Airworthiness Limitations Section
of the Instructions for Continued Airworthiness to incorporate new
limitations for fuel tank systems. You may obtain further information
by examining the MCAI in the AD docket.
Comments
We gave the public the opportunity to participate in developing
this AD. We received no comments on the NPRM or on the determination of
the cost to the public.
Clarification of Identity of Model DHC-8-201 Airplanes
We have clarified the identity of certain airplanes as listed in
the supplemental NPRM by correctly identifying them throughout this AD
as Model DHC-8-201 airplanes.
Removal of Reference to ``a Later Revision'' of Certain Maintenance
Program Manuals (MPMs)
We removed the reference to ``a later revision of Part 2
`Airworthiness Limitations List' of the applicable de Havilland Dash 8
Series MPM'' from paragraph (f)(4) of this AD and removed Table 3 of
the NPRM, which listed the MPMs (and renumbered the subsequent table
accordingly). We removed the reference to the use of ``later
revisions'' of the applicable service information from this AD to be
consistent with FAA policy. This change will not increase the economic
burden on any operator, nor will it increase the scope of the AD, since
operators may request approval to use a later revision of the
referenced service information as an alternative method of compliance,
under the provisions of paragraph (g) of this AD.
Conclusion
We reviewed the available data and determined that air safety and
the public interest require adopting the AD with the changes described
previously. We determined that these changes will not increase the
economic burden on any operator or increase the scope of the AD.
Differences Between This AD and the MCAI or Service Information
We have reviewed the MCAI and related service information and, in
general, agree with their substance. But we might have found it
necessary to use different words from those in the MCAI to ensure the
AD is clear for U.S. operators and is enforceable. In making these
changes, we do not intend to differ substantively from the information
provided in the MCAI and related service information.
We might also have required different actions in this AD from those
in the MCAI in order to follow our FAA policies. Any such differences
are highlighted in a NOTE within the AD.
Costs of Compliance
We estimate that this AD will affect about 122 products of U.S.
registry. We also estimate that it will take about 1 work-hour per
product to comply with the basic requirements of this AD. The average
labor rate is $80 per work-hour. Based on these figures, we estimate
the cost of this AD to the U.S. operators to be $9,760, or $80 per
product.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's
authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, part A, subpart III, section 44701: General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We determined that this AD will not have federalism implications
under Executive Order 13132. This AD will not have a substantial direct
effect on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government.
For the reasons discussed above, I certify this AD:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this AD and placed it in the AD docket.
Examining the AD Docket
You may examine the AD docket on the Internet at http://
www.regulations.gov; or in person at the Docket Operations office
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains the NPRM, the regulatory evaluation,
any comments received, and other information. The street address for
the Docket Operations office (telephone (800) 647-5527) is in the
ADDRESSES section. Comments will be available in the AD docket shortly
after receipt.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
0
Accordingly, under the authority delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by adding the following new AD:
2008-13-09 Bombardier, Inc. (Formerly de Havilland, Inc.): Amendment
39-15572. Docket No. FAA-2008-0179; Directorate Identifier 2007-NM-
367-AD.
Effective Date
(a) This airworthiness directive (AD) becomes effective
September 17, 2008.
Affected ADs
(b) None.
Applicability
(c) This AD applies to all Bombardier Model DHC-8-102, DHC-8-
103, DHC-8-106, DHC-8-201, DHC-8-202, DHC-8-301, DHC-8-311, and DHC-
8-315 airplanes, certificated in any category, all serial numbers.
Note 1: This AD requires revisions to certain operator
maintenance documents to include new inspections. Compliance with
these inspections is required by 14 CFR 91.403(c). For airplanes
that have been previously modified, altered, or repaired in the
areas addressed by these inspections, the operator may not be able
to accomplish the inspections described in the revisions. In this
situation, to comply with 14 CFR 91.403(c), the operator must
request approval for an alternative method of compliance according
to paragraph (g) of this AD. The request should include a
description of changes to the required inspections that will ensure
the continued operational safety of the airplane.
[[Page 47031]]
Subject
(d) Air Transport Association (ATA) of America Code 28: Fuel.
Reason
(e) The mandatory continuing airworthiness information (MCAI)
states:
Bombardier Aerospace has completed a system safety review of the
aircraft fuel system against fuel tank safety standards introduced
in Chapter 525 of the Airworthiness Manual through Notice of
Proposed Amendment (NPA) 2002-043. The identified non-compliances
were then assessed using Transport Canada Policy Letter No. 525-001,
to determine if mandatory corrective action is required.
The assessment showed that supplemental maintenance tasks
[inspections of fuel tank bonding jumpers, wiring harnesses, and
drain valve components, among other items and actions; and
applicable corrective actions] are required to prevent potential
ignition sources within the fuel system, which could result in a
fuel tank explosion. Revisions have been made to Part 2
``Airworthiness Limitations List'' of the DHC-8 Maintenance Program
Manuals to introduce the required maintenance tasks.
The corrective action is revising the Airworthiness Limitations
Section (ALS) of the Instructions for Continued Airworthiness to
incorporate new limitations for fuel tank systems.
Actions and Compliance
(f) Unless already done, do the following actions.
(1) Within 60 days after the effective date of this AD, or
before December 16, 2008, whichever occurs first, revise the ALS of
the Instructions for Continued Airworthiness to incorporate the fuel
system limitations tasks identified in the de Havilland temporary
revisions (TRs) to Part 2, ``Airworthiness Limitations List,'' of
the Dash 8 Series Maintenance Program Manuals (``the MPMs''). The
TRs are listed in Table 1 of this AD. For the tasks identified in
the TRs, the initial compliance times start at the later of the
applicable ``Threshold'' and ``Grace Period'' times specified in
Table 2 of this AD, and the repetitive limitation tasks must be
accomplished thereafter at the interval specified in the TRs, except
as provided by paragraphs (f)(2), (f)(3), (f)(4), and (g)(1) of this
AD.
Table 1--Temporary Revisions
------------------------------------------------------------------------
Model de Havilland TR MPM
------------------------------------------------------------------------
DHC-8-102, DHC-8-103, and AWL-110, dated Dash 8 Series 100
DHC-8-106 airplanes. August 31, 2007. MPM, Product
Support Manual
(PSM) 1-8-7, Part
2, ``Airworthiness
Limitations List''.
DHC-8-201, and DHC-8-202 AWL 2-43, dated Dash 8 Series 200
airplanes. August 31, 2007. MPM, PSM 1-82-7,
Part 2,
``Airworthiness
Limitations List''.
DHC-8-301, DHC-8-311, and AWL 3-109, dated Dash 8 Series 300
DHC-8-315 airplanes. August 31, 2007. MPM, PSM 1-83-7,
Part 2,
``Airworthiness
Limitations List''.
------------------------------------------------------------------------
Table 2--Initial Inspections
------------------------------------------------------------------------
Compliance time (whichever occurs later)
Description -------------------------------------------
Threshold Grace period
------------------------------------------------------------------------
Tasks with 6,000 flight Before the Within 2,000 flight
hours/36 month intervals. accumulation of hours or 12 months
6,000 total flight after the effective
hours, or within 36 date of this AD,
months since new, whichever occurs
whichever occurs first.
first.
Tasks with 18,000 flight Before the Within 6,000 flight
hours/108 month intervals. accumulation of hours or 36 months
18,000 total flight after the effective
hours, or within date of this AD,
108 months since whichever occurs
new, whichever first.
occurs first.
Tasks with 72,000 flight Before the Within 600 flight
hours/36 year intervals. accumulation of hours or 3 months
72,000 total flight after the effective
hours, or within 36 date of this AD,
years since new, whichever occurs
whichever occurs first.
first.
------------------------------------------------------------------------
Note 2: The actions required by paragraph (f)(1) of this AD may
be done by inserting a copy of the applicable TR listed in Table 1
of this AD into the ALS of the applicable MPM listed in Table 1 of
this AD. When the applicable TR has been included in general
revisions of the applicable MPM, the general revisions may be
inserted in the MPM, provided the relevant information in the
general revision is identical to that in the applicable TR.
(2) For those tasks with 6,000 flight hours/36 month limitation
task intervals: For airplanes that have accumulated 4,000 total
flight hours or more, or 24 months or more since new, as of the
effective date of this AD, do the initial limitation tasks within
2,000 flight hours or 12 months after the effective date of this AD,
whichever occurs first. Thereafter, repeat the limitation tasks at
intervals not to exceed 6,000 flight hours or 36 months, whichever
occurs first.
(3) For those tasks with 18,000 flight hours/108 month
limitation task intervals: For airplanes that have accumulated
12,000 total flight hours or more, or 72 months or more since new,
as of the effective date of this AD, do the initial limitation tasks
within 6,000 flight hours or 36 months after the effective date of
this AD, whichever occurs first. Thereafter, repeat the limitation
tasks at intervals not to exceed 18,000 flight hours or 108 months,
whichever occurs first.
(4) After accomplishing the actions specified in paragraphs
(f)(1), (f)(2), and (f)(3) of this AD, no alternative inspections/
limitation tasks or inspection/limitation task intervals may be used
unless the inspections/limitation tasks or inspection/limitation
task intervals are approved as an alternative method of compliance
(AMOC) in accordance with the procedures specified in paragraph
(g)(1) of this AD.
FAA AD Differences
Note 3: This AD differs from the MCAI and/or service information
as follows: No differences.
Other FAA AD Provisions
(g) The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, New
York ACO, FAA, has the authority to approve AMOCs for this AD, if
requested using the procedures found in 14 CFR 39.19. Send
information to ATTN: Rocco Viselli, Aerospace Engineer, Airframe and
Propulsion Branch, ANE-171, FAA, New York Aircraft Certification
Office, 1600 Stewart Avenue, Suite 410, Westbury, New York 11590;
telephone (516) 228-7331; fax (516) 794-5531. Before using any
approved AMOC on any airplane to which the AMOC applies, notify your
appropriate principal inspector (PI) in the FAA Flight Standards
District Office (FSDO), or lacking a PI, your local FSDO.
(2) Airworthy Product: For any requirement in this AD to obtain
corrective actions from a manufacturer or other source, use these
actions if they are FAA-approved. Corrective actions are considered
FAA-approved if they
[[Page 47032]]
are approved by the State of Design Authority (or their delegated
agent). You are required to assure the product is airworthy before
it is returned to service.
(3) Reporting Requirements: For any reporting requirement in
this AD, under the provisions of the Paperwork Reduction Act, the
Office of Management and Budget (OMB) has approved the information
collection requirements and has assigned OMB Control Number 2120-
0056.
Related Information
(h) Refer to MCAI Canadian Airworthiness Directive CF-2007-32,
dated December 17, 2007, and the de Havilland temporary revisions
listed in Table 1 of this AD.
Material Incorporated by Reference
(i) You must use the applicable service information specified in
Table 3 of this AD to do the actions required by this AD, unless the
AD specifies otherwise.
(1) The Director of the Federal Register approved the
incorporation by reference of this service information under 5
U.S.C. 552(a) and 1 CFR part 51.
(2) For service information identified in this AD, contact
Bombardier, Inc., Bombardier Regional Aircraft Division, 123 Garratt
Boulevard, Downsview, Ontario M3K 1Y5, Canada.
(3) You may review copies at the FAA, Transport Airplane
Directorate, 1601 Lind Avenue, SW., Renton, Washington; or at the
National Archives and Records Administration (NARA). For information
on the availability of this material at NARA, call (202) 741-6030,
or go to: http://www.archives.gov/federal-register/cfr/ibr-
locations.html.
Table 3--Material Incorporated by Reference
----------------------------------------------------------------------------------------------------------------
De Havilland temporary revision-- Dated-- To the--
----------------------------------------------------------------------------------------------------------------
AWL-110.................................. August 31, 2007......................... Dash 8 Series 100
Maintenance Program
Manual, Product Support
Manual 1-8-7, Part 2,
``Airworthiness
Limitations List''.
AWL 2-43................................. August 31, 2007......................... Dash 8 Series 200
Maintenance Program
Manual, Product Support
Manual 1-82-7, Part 2,
``Airworthiness
Limitations List''.
AWL 3-109................................ August 31, 2007......................... Dash 8 Series 300
Maintenance Program
Manual, Product Support
Manual 1-83-7, Part 2,
``Airworthiness
Limitations List''.
----------------------------------------------------------------------------------------------------------------
Issued in Renton, Washington, on July 31, 2008.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E8-18430 Filed 8-12-08; 8:45 am]
BILLING CODE 4910-13-P