[Federal Register: September 30, 2008 (Volume 73, Number 190)]
[Proposed Rules]
[Page 56763-56765]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr30se08-17]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2008-1043; Directorate Identifier 2008-NM-036-AD]
RIN 2120-AA64
Airworthiness Directives; 328 Support Services GmbH Dornier Model
328-100 Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: We propose to adopt a new airworthiness directive (AD) for the
products listed above. This proposed AD results from mandatory
continuing airworthiness information (MCAI) originated by an aviation
authority of another country to identify and correct an unsafe
condition on an aviation product. The MCAI describes the unsafe
condition as:
During overhaul on a Dornier 328-100 landing gear unit, parts of
the MLG (main landing gear) main body and trailing arm bushings have
been found corroded. Investigation showed that over time, these
bushings can migrate, creating the risk of corrosion in adjacent
areas. Such corrosion, if not detected, could cause damage to the
MLG, possibly resulting in MLG functional problems or failure.
* * * * *
Functional problems or failure of the MLG could result in the inability
of the MLG to extend or retract. The proposed AD would require actions
that are intended to address the unsafe condition described in the
MCAI.
DATES: We must receive comments on this proposed AD by October 30,
2008.
ADDRESSES: You may send comments by any of the following methods:
Federal eRulemaking Portal: Go to http://
www.regulations.gov. Follow the instructions for submitting comments.
Fax: (202) 493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue, SE., Washington, DC 20590.
Hand Delivery: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-40, 1200 New
Jersey Avenue, SE., Washington, DC, between 9 a.m. and 5 p.m., Monday
through Friday, except Federal holidays.
Examining the AD Docket
You may examine the AD docket on the Internet at http://
www.regulations.gov; or in person at the Docket Operations office
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this proposed AD, the regulatory
evaluation, any comments received, and other information. The street
address for the Docket Operations office (telephone (800) 647-5527) is
in the ADDRESSES section. Comments will be available in the AD docket
shortly after receipt.
FOR FURTHER INFORMATION CONTACT: Dan Rodina, Aerospace Engineer,
International Branch, ANM-116, FAA, Transport Airplane Directorate,
1601 Lind Avenue, SW., Renton, Washington
[[Page 56764]]
98057-3356; telephone (425) 227-2125; fax (425) 227-1149.
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to send any written relevant data, views, or
arguments about this proposed AD. Send your comments to an address
listed under the ADDRESSES section. Include ``Docket No. FAA-2008-1043;
Directorate Identifier 2008-NM-036-AD'' at the beginning of your
comments. We specifically invite comments on the overall regulatory,
economic, environmental, and energy aspects of this proposed AD. We
will consider all comments received by the closing date and may amend
this proposed AD based on those comments.
We will post all comments we receive, without change, to http://
www.regulations.gov, including any personal information you provide. We
will also post a report summarizing each substantive verbal contact we
receive about this proposed AD.
Discussion
The European Aviation Safety Agency (EASA), which is the Technical
Agent for the Member States of the European Community, has issued EASA
Airworthiness Directive 2008-0009, dated January 11, 2008 (referred to
after this as ``the MCAI''), to correct an unsafe condition for the
specified products. The MCAI states:
During overhaul on a Dornier 328-100 landing gear unit, parts of
the MLG (main landing gear) main body and trailing arm bushings have
been found corroded. Investigation showed that over time, these
bushings can migrate, creating the risk of corrosion in adjacent
areas. Such corrosion, if not detected, could cause damage to the
MLG, possibly resulting in MLG functional problems or failure.
Based on these findings, the existing mandatory retrofit
limitation (as required by Airworthiness Limitations Document under
Section E ``Mandatory Retrofit Items'' since 16 September 1998) for
the MLG bushings at 15,000 FC (flight cycles) has been amended with
`` * * * or 6 calendar years time-in-service (TIS), whichever occurs
first''.
For the reasons described above, this [EASA] Airworthiness
Directive requires the implementation of the revised mandatory
retrofit limitation and modification of MLG bushings that have
exceeded the new limit.
Functional problems or failure of the MLG could result in the inability
of the MLG to extend or retract. You may obtain further information by
examining the MCAI in the AD docket.
Relevant Service Information
328 Support Services GmbH has issued Dornier Service Bulletin SB-
328-32-245, Revision 2, dated November 21, 2007; and Dornier 328
Temporary Revision (TR) ALD-084, dated November 7, 2005, to the Dornier
328 Airworthiness Limitations Document. Messier-Dowty has issued
Service Bulletin 800-32-014, Revision 1, dated July 19, 1999. The
actions described in this service information are intended to correct
the unsafe condition identified in the MCAI.
FAA's Determination and Requirements of This Proposed AD
This product has been approved by the aviation authority of another
country, and is approved for operation in the United States. Pursuant
to our bilateral agreement with the State of Design Authority, we have
been notified of the unsafe condition described in the MCAI and service
information referenced above. We are proposing this AD because we
evaluated all pertinent information and determined an unsafe condition
exists and is likely to exist or develop on other products of the same
type design.
Differences Between This AD and the MCAI or Service Information
We have reviewed the MCAI and related service information and, in
general, agree with their substance. But we might have found it
necessary to use different words from those in the MCAI to ensure the
AD is clear for U.S. operators and is enforceable. In making these
changes, we do not intend to differ substantively from the information
provided in the MCAI and related service information.
We might also have proposed different actions in this AD from those
in the MCAI in order to follow FAA policies. Any such differences are
highlighted in a Note within the proposed AD.
Costs of Compliance
Based on the service information, we estimate that this proposed AD
would affect about 13 products of U.S. registry. We also estimate that
it would take about 28 work-hours per product to comply with the basic
requirements of this proposed AD. The average labor rate is $80 per
work-hour. Required parts would cost about $10,000 per product. Where
the service information lists required parts costs that are covered
under warranty, we have assumed that there will be no charge for these
costs. As we do not control warranty coverage for affected parties,
some parties may incur costs higher than estimated here. Based on these
figures, we estimate the cost of the proposed AD on U.S. operators to
be $159,120, or $12,240 per product.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106 describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's
authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, Part A, Subpart III, Section 44701: General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this proposed AD and placed it in the AD docket.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
[[Page 56765]]
Sec. 39.13 [Amended]
2. The FAA amends Sec. 39.13 by adding the following new AD:
328 Support Services GmbH (Formerly, AvCraft Aerospace GmbH,
formerly Fairchild Dornier GmbH, formerly Dornier Luftfahrt GmbH):
Docket No. FAA-2008-1043; Directorate Identifier 2008-NM-036-AD.
Comments Due Date
(a) We must receive comments by October 30, 2008.
Affected ADs
(b) None.
Applicability
(c) This AD applies to 328 Support Services GmbH Dornier Model
328-100 airplanes, all serial numbers, certificated in any category.
Subject
(d) Air Transport Association (ATA) of America Code 32: Landing
gear.
Reason
(e) The mandatory continuing airworthiness information (MCAI)
states:
During overhaul on a Dornier 328-100 landing gear unit, parts of
the MLG (main landing gear) main body and trailing arm bushings have
been found corroded. Investigation showed that over time, these
bushings can migrate, creating the risk of corrosion in adjacent
areas. Such corrosion, if not detected, could cause damage to the
MLG, possibly resulting in MLG functional problems or failure.
Based on these findings, the existing mandatory retrofit
limitation (as required by Airworthiness Limitations Document under
Section E ``Mandatory Retrofit Items'' since 16 September 1998) for
the MLG bushings at 15,000 FC (flight cycles) has been amended with
``* * * or 6 calendar years time-in-service (TIS), whichever occurs
first''.
For the reasons described above, this [EASA] Airworthiness
Directive requires the implementation of the revised mandatory
retrofit limitation and modification of MLG bushings that have
exceeded the new limit.
Functional problems or failure of the MLG could result in the
inability of the MLG to extend or retract.
Actions and Compliance
(f) Unless already done, do the following actions.
(1) Modify the MLG main body and trailing arm bushings at the
applicable time specified in paragraph (f)(1)(i) or (f)(1)(ii) of
this AD, or within 12 months after the effective date of this AD,
whichever occurs later. Do the modification in accordance with the
instructions of Dornier Service Bulletin SB-328-32-245, Revision 2,
dated November 21, 2007; and Messier-Dowty Service Bulletin 800-32-
014, Revision 1, dated July 19, 1999.
(i) For airplanes on which the bushings have not been replaced
as of the effective date of this AD: Before the MLG accumulates
15,000 flight cycles or 6 years, whichever occurs first.
(ii) For airplanes on which the bushings have been replaced as
of the effective date of this AD: Before the MLG exceeds 15,000
flight cycles or 6 years after replacement of the bushings,
whichever occurs first.
(2) Within 1 month after the effective date of this AD: Revise
the Airworthiness Limitations (AWL) section of the Instructions for
Continued Airworthiness by incorporating the information in Dornier
328 Temporary Revision (TR) ALD-084, dated November 7, 2005, into
Section E, ``Mandatory Retrofit Items'' of the Dornier 328
Airworthiness Limitations Document (ALD).
Note 1: The actions required by paragraph (f)(2) of this AD may
be done by inserting a copy of Dornier 328 TR ALD-084 into Section E
of the Dornier 328 ALD.
(3) After doing the replacement required by paragraph (f)(1) of
this AD, no person may install, on any airplane, a MLG unit as a
replacement part, unless it has been modified in accordance with
paragraph (f)(1) of this AD.
FAA AD Differences
Note 2: This AD differs from the MCAI and/or service information
as follows: No differences.
Other FAA AD Provisions
(g) The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
International Branch, ANM-116, FAA, has the authority to approve
AMOCs for this AD, if requested using the procedures found in 14 CFR
39.19. Send information to ATTN: Dan Rodina, Aerospace Engineer,
International Branch, ANM-116, FAA, Transport Airplane Directorate,
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone
(425) 227-2125; fax (425) 227-1149. Before using any approved AMOC
on any airplane to which the AMOC applies, notify your appropriate
principal inspector (PI) in the FAA Flight Standards District Office
(FSDO), or lacking a PI, your local FSDO.
(2) Airworthy Product: For any requirement in this AD to obtain
corrective actions from a manufacturer or other source, use these
actions if they are FAA-approved. Corrective actions are considered
FAA-approved if they are approved by the State of Design Authority
(or their delegated agent). You are required to assure the product
is airworthy before it is returned to service.
(3) Reporting Requirements: For any reporting requirement in
this AD, under the provisions of the Paperwork Reduction Act, the
Office of Management and Budget (OMB) has approved the information
collection requirements and has assigned OMB Control Number 2120-
0056.
Related Information
(h) Refer to MCAI European Aviation Safety Agency Airworthiness
Directive 2008-0009, dated January 11, 2008; Messier-Dowty Service
Bulletin 800-32-014, Revision 1, dated July 19, 1999; Dornier
Service Bulletin SB-328-32-245, Revision 2, dated November 21, 2007;
and Dornier 328 TR ALD-084, dated November 7, 2005, to the Dornier
328 Airworthiness Limitations Document; for related information.
Issued in Renton, Washington, on September 20, 2008.
Michael Kaszycki,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E8-22907 Filed 9-29-08; 8:45 am]
BILLING CODE 4910-13-P