[Federal Register: October 23, 2008 (Volume 73, Number 206)]
[Proposed Rules]
[Page 63090-63094]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr23oc08-18]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2008-0952; Directorate Identifier 98-ANE-49-AD]
RIN 2120-AA64
Airworthiness Directives; General Electric Company CF6-80A, CF6-
80C2, and CF6-80E1 Series Turbofan Engines
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: The FAA proposes to supersede an existing airworthiness
directive (AD) for General Electric Company (GE) CF6-80A, CF6-80C2, and
CF6-80E1 series turbofan engines. That AD currently requires revisions
to the Airworthiness Limitations Section (ALS) of the manufacturer's
Instructions for Continued Airworthiness (ICA) to include required
inspection of selected critical life-limited parts at each piece-part
exposure. This proposed AD would require revisions to the CF6-80A, CF6-
80C2, and CF6-80E1 series engines ALS sections of the manufacturer's
manuals and an air carrier's approved continuous airworthiness
maintenance program to incorporate additional inspection requirements,
and to update certain Engine Manual Inspection Task and Sub Task Number
references. This proposed AD results from the need to require enhanced
inspection of selected critical life-limited parts of CF6-80A, CF6-
80C2, and CF6-80E1 series engines. We are proposing this AD to prevent
critical life-limited rotating engine part failure, which could result
in an uncontained engine failure and damage to the airplane.
DATES: We must receive any comments on this proposed AD by December 22,
2008.
ADDRESSES: Use one of the following addresses to comment on this
proposed AD.
Federal eRulemaking Portal: Go to http://
www.regulations.gov and follow the instructions for sending your
comments electronically.
Mail: Docket Management Facility, U.S. Department of
Transportation, 1200 New Jersey Avenue, SE., West Building Ground
Floor, Room W12-140, Washington, DC 20590-0001.
Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
Fax: (202) 493-2251.
FOR FURTHER INFORMATION CONTACT: Robert Green, Aerospace Engineer,
Engine Certification Office, FAA, Engine & Propeller Directorate, 12
New England Executive Park, Burlington, MA 01803; e-mail:
robert.green@faa.gov; telephone (781) 238-7754; (781) 238-7199.
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to send any written relevant data, views, or
arguments regarding this proposal. Send your comments to an address
listed under ADDRESSES. Include ``Docket No. FAA-2008-0952; Directorate
Identifier 98-ANE-49-AD'' in the subject line of your comments. We
specifically invite comments on the overall regulatory, economic,
environmental, and energy aspects of the proposed AD. We will consider
all comments received by the closing date and may amend the proposed AD
in light of those comments.
We will post all comments we receive, without change, to http://
www.regulations.gov, including any personal information you provide. We
will also post a report summarizing each substantive verbal contact
with FAA personnel concerning this proposed AD. Using the search
function of the Web site, anyone can find and read the comments in any
of our dockets, including, if provided, the name of the individual who
sent the comment (or signed the comment on behalf of an association,
business, labor union, etc.). You may review the DOT's complete Privacy
Act Statement in the Federal Register published on April 11, 2000 (65
FR 19477-78).
Examining the AD Docket
You may examine the AD docket on the Internet at http://
www.regulations.gov; or in person at the Docket Operations office
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this proposed AD, the regulatory
evaluation, any comments received, and other information. The street
address for the Docket Operations office (telephone (800) 647-5527) is
the same as the Mail address provided in the ADDRESSES section.
Comments will be available in the AD docket shortly after receipt.
Discussion
On April 3, 2002, we issued AD 2002-07-12, Amendment 39-12707 (67
FR 17279, April 10, 2002), to require revisions to the ALS of the
manufacturer's ICA for GE CF6-80A, CF6-80C2, and CF6-80E1 series
turbofan engines to include required enhanced inspection of selected
critical life-limited parts at each piece-part exposure.
Additional Inspection Procedures
Since the issuance of that AD, an FAA study of in-service events
involving uncontained failures of critical rotating engine parts has
indicated the need for additional mandatory inspections. The mandatory
inspections are needed to identify those critical rotating parts with
conditions, which if allowed to continue in service, could result in
uncontained engine failures. This proposal would require revisions to
the CF6-80A, CF6-80C2, and CF6-80E1 series engines ALS sections of the
manufacturer's manuals and an air carrier's approved continuous
airworthiness maintenance program to incorporate additional inspection
requirements.
FAA's Determination and Requirements of the Proposed AD
Since an unsafe condition has been identified that is likely to
exist or develop on other products of this same type design, the
proposed AD would supersede AD 2002-07-12 to add additional inspections
for certain high-pressure turbine (HPT) components, and to update
certain Engine Manual Inspection Task and or Sub Task Number
references. These inspections would be required at each piece-part
opportunity. For reference, this proposed AD carries forward the
requirements from AD 2002-07-12. Also for reference, the parts added to
the table in the compliance section of this AD are identified by an
asterisk (*) that precedes the part nomenclature. Also for reference,
parts that have an Engine Manual Inspection Task and or Sub Task Number
reference updated in the table in the compliance section of this AD,
are identified by two asterisks (**) that precede the part
nomenclature.
Costs of Compliance
We estimate that this proposed AD would affect 315 CF6-80A series
engines and 926 CF6-80C2 series engines installed on airplanes of U.S.
[[Page 63091]]
registry. We also estimate that it would take about 5 work-hours per
CF6-80A series engine and about 2 work-hours per CF6-80C2 series engine
to do the proposed additional inspections and that the average labor
rate is $80 per work-hour. The total cost of the new inspections per
CF6-80A series engine would be about $400. The total cost of the new
inspections per CF6-80C2 series engine would be about $160. We estimate
that there will be about 42 shop visits per year for CF6-80A series
engines, and about 128 shop visits per year for CF6-80C2 series engines
that result in piece-part-exposure of the added affected components.
Therefore, we estimate the total annual cost for the additional
inspections to be $37,280.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
Requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We have determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify that the proposed AD:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Would not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this proposed AD. See the ADDRESSES section for a location
to examine the regulatory evaluation.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Under the authority delegated to me by the Administrator, the
Federal Aviation Administration proposes to amend 14 CFR part 39 as
follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. The FAA amends Sec. 39.13 by removing Amendment 39-12707 (67 FR
17279, April 10, 2002) and by adding a new airworthiness directive to
read as follows:
General Electric Company: Docket No. FAA-2008-0952; Directorate
Identifier 98-ANE-49-AD.
Comments Due Date
(a) The Federal Aviation Administration (FAA) must receive
comments on this airworthiness directive (AD) action by December 22,
2008.
Affected ADs
(b) This AD supersedes AD 2002-07-12, Amendment 39-12707.
Applicability
(c) This AD applies to General Electric Company CF6-80A, CF6-
80C2, and CF6-80E1 series turbofan engines. These engines are
installed on, but not limited to, Airbus A300, A310, and A330
series, Boeing 747 and 767 series, and McDonnell Douglas MD-11
series airplanes.
Unsafe Condition
(d) This AD results from the need to require enhanced inspection
of selected critical life-limited parts of CF6-80A, CF6-80C2, and
CF6-80E1 series engines. We are issuing this AD to prevent critical
life-limited rotating engine part failure, which could result in an
uncontained engine failure and damage to the airplane.
Compliance
(e) You are responsible for having the actions required by this
AD performed within the compliance times specified unless the
actions have already been done.
Inspections
(f) Within the next 180 days after the effective date of this
AD, revise the Airworthiness Limitations Section (ALS) of the
manufacturer's Instructions for Continued Airworthiness (ICA), and
for air carrier operations revise the approved continuous
airworthiness maintenance program, by adding the following:
``MANDATORY INSPECTIONS
(1) Perform inspections of the following parts at each piece-
part opportunity in accordance with the instructions provided in the
applicable manual provisions:
------------------------------------------------------------------------
Inspect per engine
Part nomenclature Part No. (P/N) manual inspection
chapter
------------------------------------------------------------------------
For CF6-80A Engines
------------------------------------------------------------------------
Disk, Fan Rotor, Stage 1...... All.............. 72-21-03 Paragraph 3.
Fluorescent-
Penetrant Inspect,
and 72-21-03
Paragraph 4. Eddy
Current Inspect.
Fan Forward Shaft............. All.............. 72-21-05 Paragraph 2.
Magnetic Particle
Inspect.
Fan Mid Shaft................. All.............. 72-24-01 Paragraph 2.
Magnetic Particle
Inspect.
Disk, HPC Rotor, Stage One.... All.............. 72-31-04 Paragraph 3.
Fluorescent-
Penetrant Inspect.
** Disk, HPC Rotor, Stage Two. All.............. 72-31-05 Paragraph 4.
Fluorescent-
Penetrant Inspect.
Spool, HPC Rotor, Stage 3-9... All.............. 72-31-06 Paragraph 3.
Fluorescent-
Penetrant Inspect.
Disk, HPC Rotor, Stage 10..... All.............. 72-31-07 Paragraph 3.
Fluorescent-
Penetrant Inspect.
Spool, HPC Rotor, Stage 11-14. All.............. 72-31-08 Paragraph
3.A. Fluorescent-
Penetrant Inspect.
Rotating CDP Seal............. All.............. 72-31-10 Paragraph 3.
Fluorescent-
Penetrant Inspect.
Disk Shaft, HPT Rotor Stage All.............. 72-53-02 Paragraph 3.
One. Fluorescent-
Penetrant Inspect
per 70-32-02, and
72-53-02 Paragraph
6.C. Disk Rim Bolt
Hole Eddy Current
Inspection, and
72-53-02 Paragraph
6.D. Disk Bore Eddy
Current Inspection.
* Disk Shaft, HPT Rotor Stage All.............. 72-53-02 Paragraph
One. 6.E. Disk Dovetail
Slot Bottom Eddy
Current Inspection.
[[Page 63092]]
* Disk Shaft, HPT Rotor, Stage P/Ns 2047M33G01 72-53-02 Paragraph 7.
One. thru G10, and P/ Disk Dovetail Slot
N 9362M58G11. Bottom Aft Corner
Chamfers Eddy
Current Inspection.
Disk, HPT Rotor, Stage Two.... All.............. 72-53-06 Paragraph 3.
Fluorescent-
Penetrant
Inspection, and
72-53-06 Paragraph 6.
Eddy Current
Inspection of Rim
Bolt Holes for
Cracks, and
72-53-06 Paragraph 7.
Disk Bore Eddy
Current Inspection.
Disk, LPT Rotor Stage 1-4..... All.............. 72-57-02 Paragraph 3.
Fluorescent-
Penetrant
Inspection.
Shaft, LPT Rotor.............. All.............. 72-57-03 Paragraph 3.
Fluorescent-
Penetrant
Inspection, and
72-57-03 Paragraph 6.
Eddy Current
Inspection.
------------------------------------------------------------------------
For All CF6-80C2 Engines
------------------------------------------------------------------------
Disk, Fan Rotor, Stage 1...... All.............. Task 72-21-03-200-000-
004 Fluorescent-
Penetrant
Inspection, and
Task 72-21-03-200-000-
008 Eddy Current
Inspect Fan Rotor
Disk Stage 1 Bore,
Forward and Aft Hub
Faces, and Bore
Radii.
Shaft, Fan Forward............ All.............. Task 72-21-05-200-000-
001 Fluorescent
Penetrant
Inspection, and
Task 72-21-05-200-000-
005 Vent Hole Eddy
Current Inspection.
Fan Mid Shaft................. All.............. Task 72-24-01-200-000-
003 Magnetic
Particle Inspection.
HPCR Stage 1 Disk............. All.............. Task 72-31-04-200-000-
002 Fluorescent
Penetrant
Inspection.
HPCR Stage 2 Disk............. All.............. Task 72-31-05-200-000-
002 Fluorescent
Penetrant
Inspection.
HPCR Stage 3-9 Spool.......... All.............. Task 72-31-06-200-000-
001 Fluorescent
Penetrant
Inspection.
HPCR Stage 10 Disk............ All.............. Task 72-31-07-200-000-
001 Fluorescent
Penetrant
Inspection.
HPCR Stage 11-14 Spool/Shaft.. All.............. Task 72-31-08-200-000-
002 Fluorescent
Penetrant
Inspection.
No. 4 Bearing Rotating (CDP) All.............. Task 72-31-10-200-000-
Air Seal. 001 Fluorescent
Penetrant Inspection
or
Task 72-31-10-200-000-
A01 Fluorescent
Penetrant
Inspection.
HPCR Stage 10-14 Spool/Shaft.. All.............. Task 72-31-22-200-000-
002 Fluorescent
Penetrant
Inspection.
** Disk/Shaft, HPT Rotor, All.............. Task 72-53-02-200-000-
Stage One. 001 (Inspection--
Configuration 1), or
Task 72-53-02-230-
801 (Inspection--
Configuration 2),
Fluorescent-
Penetrant Inspect,
and
Task 72-53-02-200-000-
005 (Inspection--
Configuration 1), or
Task 72-53-02-250-
802 (Inspection--
Configuration 2),
Disk Rim Bolt Hole
Eddy Current
Inspection, and
Task 72-53-02-200-000-
006 (Inspection--
Configuration 1), or
Task 72-53-02-250-
803 (Inspection--
Configuration 2),
Disk Bore Area Eddy
Current Inspection,
and
Task 72-53-02-200-000-
007 (Inspection--
Configuration 1), or
Task 72-53-02-250-
804 (Inspection--
Configuration 2),
Disk Dovetail Slot
Bottom Eddy Current.
* Disk/Shaft, HPT Rotor, Stage P/N 1531M84G12 Task 72-53-02-250-801
One. and P/Ns (Inspection--Configu
2047M32G01 thru ration 1), Disk
G07. Dovetail Slot Bottom
Aft Corner Chamfers
Eddy Current
Inspection.
Disk, HPT Rotor, Stage Two.... All.............. Task 72-53-06-200-000-
002 Fluorescent-
Penetrant Inspect,
and
Task 72-53-06-200-000-
006 Disk Rim Bolt
Hole Eddy Current
Inspection, and
Task 72-53-06-200-000-
007 Disk Bore Eddy
Current Inspection.
LPTR Stage 1-5 Disks.......... All.............. Task 72-57-02-200-000-
001 Fluorescent-
Penetrant
Inspection.
LPTR Shaft.................... All.............. Task 72-57-03-200-000-
002 Fluorescent-
Penetrant Inspect,
and
Task 72-57-03-200-000-
006 Eddy Current
Inspection.
------------------------------------------------------------------------
For CF6-80C2 Engines configured with the R88DT Turbine (Models CF6-
80C2B2F, 80C2B4F, 80C2B6F, 80C2B7F, 80C2B8F)
------------------------------------------------------------------------
Disk/Shaft, HPT Rotor, Stage All.............. Task 72-53-16-200-000-
One (R88DT, No Rim Bolt 001 Fluorescent-
Holes). Penetrant Inspect,
and
Task 72-53-16-200-000-
005 Disk Bore Area
Eddy Current
Inspection.
Disk, HPT Rotor, Stage Two All.............. Task 72-53-18-200-000-
(R88DT, No Rim Bolt Holes). 002 Fluorescent-
Penetrant Inspect,
and
Task 72-53-18-200-000-
005 Disk Bore Area
Eddy Current
Inspection.
Rotating Interstage Seal All.............. Task 72-53-17-200-000-
(R88DT). 001 Fluorescent-
Penetrant Inspect,
and
Task 72-53-17-200-000-
005 Seal Bore Area
Eddy Current.
Forward Outer Seal (R88DT).... All.............. Task 72-53-21-200-000-
001 Fluorescent-
Penetrant Inspect,
and
Task 72-53-21-200-000-
004 Seal Bore Area
Eddy Current.
------------------------------------------------------------------------
For CF6-80E1 Engines
------------------------------------------------------------------------
Disk, Fan Rotor, Stage One.... All.............. Sub Task 72-21-03-230-
051 Fluorescent-
Penetrant
Inspection, and
Sub Task 72-21-03-250-
051 or 72-21-03-250-
052 Disk Bore Eddy
Current Inspection.
Shaft, Fan.................... All.............. Sub Task 72-21-05-230-
051 Fluorescent
Penetrant
Inspection, and
Sub Task 72-21-05-250-
051 Vent Hole Eddy
Current Inspection.
Compressor Rotor, Stage 1 Disk All.............. Sub Task 72-31-04-230-
051 Fluorescent
Penetrant
Inspection.
Compressor Rotor, Stage 2 Disk All.............. Sub Task 72-31-05-230-
051 Fluorescent
Penetrant
Inspection.
[[Page 63093]]
Compressor Rotor, Stage 3-9 All.............. Sub Task 72-31-06-230-
Spool. 051 Fluorescent
Penetrant
Inspection.
Compressor Rotor, Stage 10 All.............. Sub Task 72-31-07-230-
Disk (Pre SB 72-0150). 051 Fluorescent
Penetrant
Inspection.
Compressor Rotor Spool/Shaft, All.............. Sub Task 72-31-08-230-
Stage 11-14 (Pre SB 72-0150). 051 Fluorescent
Penetrant
Inspection.
Compressor Rotor Spool/Shaft, All.............. Sub Task 72-31-23-230-
Stage 10-14 (SB 72-0150). 052 Fluorescent
Penetrant
Inspection.
Compressor Rotor No. 4 Bearing All.............. Sub Task 72-31-10-230-
Rotating Air Seal (CDP 051 Fluorescent
Rotating Seal). Penetrant
Inspection.
HPT Disk/Shaft, Stage 1....... All.............. Sub Task 72-53-02-230-
051 Fluorescent-
Penetrant
Inspection, and
Sub Task 72-53-02-250-
051 Eddy Current
Inspection, Rim Bolt
Holes, and
Sub Task 72-53-02-250-
054 Eddy Current
Inspection, Disk
Bore.
HPT Disk, Stage 2............. All.............. Sub Task 72-53-06-230-
051 Fluorescent-
Penetrant
Inspection, and
Sub Task 72-53-06-250-
051 Eddy Current
Inspection, Rim Bolt
Holes, and
Sub Task 72-53-06-250-
054 Eddy Current
Inspection, Disk
Bore.
LPT Rotor Shaft............... All.............. Sub Task 72-55-01-240-
051 Magnetic
Particle Inspect.
LPT Disks, Stages 1-5......... All.............. Sub Task 72-57-02-230-
051 Fluorescent-
Penetrant Inspect.
LPT Rotor Torque Cone......... All.............. Sub Task 72-57-03-220-
051 Fluorescent-
Penetrant Inspect.
------------------------------------------------------------------------
For CF6-80E1 Engines configured with the R88DT Turbine
------------------------------------------------------------------------
Disk/Shaft, HPT Rotor, Stage 1 All.............. Sub Task 72-53-16-230-
(R88DT, No Rim Bolt Holes). 052 Fluorescent-
Penetrant Inspect,
and
Sub Task 72-53-16-250-
051 Disk Bore Area
Eddy Current
Inspection.
Disk, HPT Rotor, Stage 2 All.............. Sub Task 72-53-18-230-
(R88DT, No Rim Bolt Holes). 051 Fluorescent-
Penetrant Inspect,
and
Sub Task 72-53-18-250-
051 Disk Bore Area
Eddy Current
Inspection.
** HPT Rotor Rotating All.............. Sub Task 72-53-17-230-
Interstage Seal (R88DT). 056 Fluorescent-
Penetrant Inspect,
and
Sub Task 72-53-17-250-
051 Seal Bore Area
Eddy Current.
HPT Rotor Forward Outer Seal All.............. Sub Task 72-53-21-230-
(R88DT). 051 Fluorescent-
Penetrant Inspect,
and
Sub Task 72-53-21-250-
051 Seal Bore Area
Eddy Current.
------------------------------------------------------------------------
(2) For the purposes of these mandatory inspections, piece-part
opportunity means:
(i) The part is considered completely disassembled when
accomplished in accordance with the disassembly instructions in the
manufacturer's engine manual; and
(ii) The part has accumulated more than 100 cycles-in-service
since the last piece-part opportunity inspection, provided that the
part was not damaged or related to the cause for its removal from
the engine.
(g) The parts added to the table of this AD are identified by an
asterisk (*) that precedes the part nomenclature. Also, parts that
have an Engine Manual Inspection Task and/or Sub Task Number
reference updated in the table of this AD, are identified by two
asterisks (**) that precede the part nomenclature.
(h) Except as provided in paragraph (i) of this AD, and
notwithstanding contrary provisions in section 43.16 of the Federal
Aviation Regulations (14 CFR 43.16), these mandatory inspections
shall be performed only in accordance with the ALS of the
manufacturer's ICA.
Alternative Methods of Compliance (AMOC)
(i) You must perform these mandatory inspections using the ALS
of the ICA and the applicable Engine Manual unless you receive
approval to use an AMOC under paragraph (j) of this AD. Section
43.16 of the Federal Aviation Regulations (14 CFR 43.16) may not be
used to approve alternative methods of compliance or adjustments to
the times in which these inspections must be performed.
(j) The Manager, Engine Certification Office, has the authority
to approve alternative methods of compliance for this AD if
requested using the procedures found in 14 CFR 39.19.
Maintaining Records of the Mandatory Inspections
(k) You have met the requirements of this AD when you revise the
ALS of the manufacturer's ICA as specified in paragraph (f) of this
AD. For air carriers operating under part 121 of the Federal
Aviation Regulations (14 CFR part 121), you have met the
requirements of this AD when you modify your continuous
airworthiness maintenance plan to reflect those changes. You do not
need to record each piece-part inspection as compliance to this AD,
but you must maintain records of those inspections according to the
regulations governing your operation. For air carriers operating
under part 121, you may use either the system established to comply
with section 121.369 or an alternative accepted by your principal
maintenance inspector if that alternative:
(1) Includes a method for preserving and retrieving the records
of the inspections resulting from this AD; and
(2) Meets the requirements of section 121.369(c); and
(3) Maintains the records either indefinitely or until the work
is repeated.
(l) These recordkeeping requirements apply only to the records
used to document the mandatory inspections required as a result of
revising the ALS of the manufacturer's ICA as specified in paragraph
(f) of this AD. These recordkeeping requirements do not alter or
amend the recordkeeping requirements for any other AD or regulatory
requirement.
Related Information
(m) Contact Robert Green, Aerospace Engineer, Engine
Certification Office, FAA, Engine & Propeller Directorate, 12 New
England Executive Park, Burlington, MA 01803; e-mail:
robert.green@faa.gov; telephone (781) 238-7754; fax (781) 238-7199,
for more information about this AD.
[[Page 63094]]
Issued in Burlington, Massachusetts, on October 16, 2008.
Peter A. White,
Assistant Manager, Engine and Propeller Directorate, Aircraft
Certification Service.
[FR Doc. E8-25278 Filed 10-22-08; 8:45 am]
BILLING CODE 4910-13-P