[Federal Register: October 31, 2008 (Volume 73, Number 212)]
[Proposed Rules]
[Page 64897-64899]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr31oc08-24]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2008-1141; Directorate Identifier 2008-NM-025-AD]
RIN 2120-AA64
Airworthiness Directives; BAE Systems (Operations) Limited Model
BAe 146 and Avro 146-RJ Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: We propose to adopt a new airworthiness directive (AD) for the
products listed above. This proposed AD results from mandatory
continuing airworthiness information (MCAI) originated by an aviation
authority of another country to identify and correct an unsafe
condition on an aviation product. The MCAI describes the unsafe
condition as:
During removal of forward and aft wing links, corrosion has been
found on the wing links and the wing link attachment bolts in areas
that are not readily accessible during the currently required
Maintenance Review Board Report (MRBR) zonal inspections or
Corrosion Prevention and Control Programme (CPCP) inspections. If
left uncorrected, such corrosion could adversely affect the
structural integrity of the wing to fuselage joint.
* * * * *
The proposed AD would require actions that are intended to address
the unsafe condition described in the MCAI.
DATES: We must receive comments on this proposed AD by December 1,
2008.
ADDRESSES: You may send comments by any of the following methods:
Federal eRulemaking Portal: Go to http://
www.regulations.gov. Follow the instructions for submitting comments.
Fax: (202) 493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue, SE., Washington, DC 20590.
Hand Delivery: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-40, 1200 New
Jersey Avenue, SE., Washington, DC, between 9 a.m. and 5 p.m., Monday
through Friday, except Federal holidays.
Examining the AD Docket
You may examine the AD docket on the Internet at http://
www.regulations.gov; or in person at the Docket Operations office
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this proposed AD, the regulatory
evaluation, any comments received, and other information. The street
address for the Docket Operations office (telephone (800) 647-5527) is
in the ADDRESSES section. Comments will be available in the AD docket
shortly after receipt.
FOR FURTHER INFORMATION CONTACT: Todd Thompson, Aerospace Engineer,
International Branch, ANM-116, Transport Airplane Directorate, FAA,
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425)
227-1175; fax (425) 227-1149.
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to send any written relevant data, views, or
arguments about this proposed AD. Send your comments to an address
listed under the ADDRESSES section. Include ``Docket No. FAA-2008-1141;
Directorate Identifier 2008-NM-025-AD'' at the beginning of your
comments. We specifically invite comments on the overall regulatory,
economic, environmental, and energy aspects of this proposed AD. We
will consider all comments received by the closing date and may amend
this proposed AD based on those comments.
We will post all comments we receive, without change, to http://
www.regulations.gov, including any personal information you provide. We
will also post a report summarizing each substantive verbal contact we
receive about this proposed AD.
Discussion
The European Aviation Safety Agency (EASA), which is the Technical
Agent for the Member States of the European Community, has issued EASA
Airworthiness Directive 2007-0303, dated December 14, 2007 (referred to
after this as ``the MCAI''), to correct an unsafe condition for the
specified products. The MCAI states:
During removal of forward and aft wing links, corrosion has been
found on the wing links and the wing link attachment bolts in areas
that are not readily accessible during the currently required
Maintenance Review Board Report (MRBR) zonal inspections or
Corrosion Prevention and Control Programme (CPCP) inspections. If
left uncorrected, such corrosion could adversely affect the
structural integrity of the wing to fuselage joint.
For this reason, this Airworthiness Directive (AD) requires
repetitive detailed visual inspections at the forward and aft wing
links and wing link attachment bolts for signs of corrosion,
replacement of corroded nuts and bolts and repair of any defects.
The MRBR and CPCP will be amended to include the repeat
inspections. You may obtain further information by examining the MCAI
in the AD docket.
Relevant Service Information
The manufacturer has issued BAE Systems (Operations) Limited
Inspection Service Bulletin ISB.53-203, dated May 7, 2007. The actions
described in this service information are intended to correct the
unsafe condition identified in the MCAI.
[[Page 64898]]
FAA's Determination and Requirements of This Proposed AD
This product has been approved by the aviation authority of another
country, and is approved for operation in the United States. Pursuant
to our bilateral agreement with the State of Design Authority, we have
been notified of the unsafe condition described in the MCAI and service
information referenced above. We are proposing this AD because we
evaluated all pertinent information and determined an unsafe condition
exists and is likely to exist or develop on other products of the same
type design.
Differences Between This AD and the MCAI or Service Information
We have reviewed the MCAI and related service information and, in
general, agree with their substance. But we might have found it
necessary to use different words from those in the MCAI to ensure the
AD is clear for U.S. operators and is enforceable. In making these
changes, we do not intend to differ substantively from the information
provided in the MCAI and related service information.
We might also have proposed different actions in this AD from those
in the MCAI in order to follow FAA policies. Any such differences are
highlighted in a Note within the proposed AD.
Costs of Compliance
Based on the service information, we estimate that this proposed AD
would affect about 1 product of U.S. registry. We also estimate that it
would take about 20 work-hours per product to comply with the basic
requirements of this proposed AD. The average labor rate is $80 per
work-hour. Based on these figures, we estimate the cost of the proposed
AD on U.S. operators to be $1,600.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's
authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, Part A, Subpart III, section 44701: General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this proposed AD and placed it in the AD docket.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. The FAA amends Sec. 39.13 by adding the following new AD:
BAE Systems (Operations) Limited (Formerly British Aerospace
Regional Aircraft): Docket No. FAA-2008-1141; Directorate Identifier
2008-NM-025-AD.
Comments Due Date
(a) We must receive comments by December 1, 2008.
Affected ADs
(b) None.
Applicability
(c) This AD applies to BAE Systems (Operations) Limited Model
BAe 146-100A, -200A, and -300A series airplanes and Avro 146-RJ70A,
146-RJ85A, and 146-RJ100A airplanes, certificated in any category,
all models, all serial numbers.
Subject
(d) Air Transport Association (ATA) of America Code 53:
Fuselage.
Reason
(e) The mandatory continuing airworthiness information (MCAI)
states:
During removal of forward and aft wing links, corrosion has been
found on the wing links and the wing link attachment bolts in areas
that are not readily accessible during the currently required
Maintenance Review Board Report (MRBR) zonal inspections or
Corrosion Prevention and Control Programme (CPCP) inspections. If
left uncorrected, such corrosion could adversely affect the
structural integrity of the wing to fuselage joint.
For this reason, this Airworthiness Directive (AD) requires
repetitive detailed visual inspections at the forward and aft wing
links and wing link attachment bolts for signs of corrosion,
replacement of corroded nuts and bolts and repair of any defects.
The MRBR and CPCP will be amended to include the repeat
inspections.
Actions and Compliance
(f) Unless already done, do the following actions: Before
accumulating 48 months on the wing link since new, or within 48
months of a wing link being repaired in accordance with a BAE
Systems (Operations) Ltd. or EASA approved repair scheme, or within
24 months after the effective date of this AD, whichever occurs
latest, and thereafter at intervals not to exceed 48 months, inspect
the wing links in accordance with paragraph 2.C. of BAE Systems
(Operations) Ltd. Inspection Service Bulletin ISB.53-203, dated May
7, 2007.
(1) If any corrosion is found on bolts or nuts, replace the
affected bolts and nuts with airworthy parts before next flight in
accordance with the service bulletin.
(2) If any corrosion to the wing links is found during an
inspection, repair before further flight in accordance with a method
approved in accordance with EASA (or its delegated agent).
FAA AD Differences
Note 1: This AD differs from the MCAI and/or service information
as follows: No differences.
Other FAA AD Provisions
(g) The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
International Branch, ANM-114, FAA, has the authority to approve
AMOCs for this AD, if requested using the procedures found in 14 CFR
39.19. Send information to ATTN: Todd Thompson, Aerospace Engineer,
Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton,
Washington 98057-3356; telephone (425) 227-1175; fax (425) 227-1149.
Before using any approved AMOC on any airplane to which the AMOC
applies, notify your appropriate principal inspector (PI) in the
[[Page 64899]]
FAA Flight Standards District Office (FSDO), or lacking a PI, your
local FSDO.
(2) Airworthy Product: For any requirement in this AD to obtain
corrective actions from a manufacturer or other source, use these
actions if they are FAA-approved. Corrective actions are considered
FAA-approved if they are approved by the State of Design Authority
(or their delegated agent). You are required to assure the product
is airworthy before it is returned to service.
(3) Reporting Requirements: For any reporting requirement in
this AD, under the provisions of the Paperwork Reduction Act, the
Office of Management and Budget (OMB) has approved the information
collection requirements and has assigned OMB Control Number 2120-
0056.
Related Information
(h) Refer to MCAI EASA Airworthiness Directive 2007-0303, dated
December 14, 2007, and BAE Systems (Operations) Limited Inspection
Service Bulletin ISB.53-203, dated May 7, 2007, for related
information.
Issued in Renton, Washington, on October 20, 2008.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E8-25999 Filed 10-30-08; 8:45 am]
BILLING CODE 4910-13-P