[Federal Register Volume 73, Number 217 (Friday, November 7, 2008)]
[Rules and Regulations]
[Pages 66171-66172]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: E8-26440]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF LABOR
Mine Safety and Health Administration
30 CFR Parts 56, 57, and 71
RIN 1219-AB24
Asbestos Exposure Limit
AGENCY: Mine Safety and Health Administration, Labor.
ACTION: Final rule, technical amendment.
-----------------------------------------------------------------------
[[Page 66172]]
SUMMARY: The Mine Safety and Health Administration (MSHA) is amending
and clarifying its existing health standards for asbestos exposure. The
amendments make no substantive change to the existing standards, MSHA's
enforcement of the standards, or the protection afforded miners under
the standards.
DATES: This technical amendment is effective November 7, 2008.
FOR FURTHER INFORMATION CONTACT: Patricia W. Silvey at
[email protected] (e-mail), 202-693-9440 (Voice), or 202-693-9441
(Fax).
SUPPLEMENTARY INFORMATION: MSHA published a final rule amending its
health standards for asbestos exposure at metal and nonmetal mines,
surface coal mines, and surface areas of underground coal mines on
February 29, 2008 (73 FR 11284). The rule became effective on April 29,
2008. To assure that the mining community fully understands MSHA's
intent with respect to certain provisions of the existing standards,
the Agency is issuing this technical amendment. This technical
amendment clarifies MSHA's definition of asbestos and analytical
methods the Agency uses to enforce the existing asbestos exposure
limit. As stated above, these clarifications do not change any
substantive requirements and reflect MSHA's intent as explained in the
preamble to the final rule issued on February 29, 2008.
List of Subjects
30 CFR Parts 56 and 57
Air quality, Asbestos, Chemicals, Hazardous substances, Metals,
Mine safety and health.
30 CFR Part 71
Air quality, Asbestos, Chemicals, Coal mining, Hazardous
substances, Mine safety and health.
Richard E. Stickler,
Acting Assistant Secretary for Mine Safety and Health.
0
For the reasons set out in the preamble, MSHA is amending title 30 of
the Code of Federal Regulations as follows.
PART 56--SAFETY AND HEALTH STANDARDS--SURFACE METAL AND NONMETAL
MINES
0
1. The authority citation for part 56 continues to read as follows:
Authority: 30 U.S.C. 811.
0
2. Amend Sec. 56.5001 by revising the introductory text of paragraph
(b)(1), adding a definition for asbestos fiber, and revising paragraph
(b)(3) to read as follows:
Sec. 56.5001 Exposure limits for airborne contaminants.
* * * * *
(b) Asbestos standard--(1) Definitions. Asbestos is a generic term
for a number of asbestiform hydrated silicates that, when crushed or
processed, separate into flexible fibers made up of fibrils.
* * * * *
Asbestos fiber means a fiber of asbestos that meets the criteria of
a fiber.
* * * * *
(3) Measurement of airborne asbestos fiber concentration. Potential
asbestos fiber concentration shall be determined by phase contrast
microscopy (PCM) using the OSHA Reference Method in OSHA's asbestos
standard found in 29 CFR 1910.1001, Appendix A, or a method at least
equivalent to that method in identifying a potential asbestos exposure
exceeding the 0.1 f/cc full-shift limit or the 1 f/cc excursion limit.
When PCM results indicate a potential exposure exceeding the 0.1 f/cc
full-shift limit or the 1 f/cc excursion limit, samples shall be
further analyzed using transmission electron microscopy according to
NIOSH Method 7402 or a method at least equivalent to that method.
* * * * *
PART 57--SAFETY AND HEALTH STANDARDS--UNDERGROUND METAL AND
NONMETAL MINES
0
3. The authority citation for part 57 continues to read as follows:
Authority: 30 U.S.C. 811.
0
4. Amend Sec. 57.5001 by revising the introductory text of paragraph
(b)(1), adding a definition for asbestos fiber, and revising paragraph
(b)(3) to read as follows:
Sec. 57.5001 Exposure limits for airborne contaminants.
* * * * *
(b) Asbestos standard--(1) Definitions. Asbestos is a generic term
for a number of asbestiform hydrated silicates that, when crushed or
processed, separate into flexible fibers made up of fibrils.
* * * * *
Asbestos fiber means a fiber of asbestos that meets the criteria of
a fiber.
* * * * *
(3) Measurement of airborne asbestos fiber concentration. Potential
asbestos fiber concentration shall be determined by phase contrast
microscopy (PCM) using the OSHA Reference Method in OSHA's asbestos
standard found in 29 CFR 1910.1001, Appendix A, or a method at least
equivalent to that method in identifying a potential asbestos exposure
exceeding the 0.1 f/cc full-shift limit or the 1 f/cc excursion limit.
When PCM results indicate a potential exposure exceeding the 0.1 f/cc
full-shift limit or the 1 f/cc excursion limit, samples shall be
further analyzed using transmission electron microscopy according to
NIOSH Method 7402 or a method at least equivalent to that method.
* * * * *
PART 71--MANDATORY HEALTH STANDARDS--SURFACE COAL MINES AND SURFACE
WORK AREAS OF UNDERGROUND COAL MINES
0
5. The authority citation for part 71 continues to read as follows:
Authority: 30 U.S.C. 811, 951, 957.
0
6. Amend Sec. 71.702 by revising the introductory text of paragraph
(a), adding a definition for asbestos fiber, and revising paragraph (c)
to read as follows:
Sec. 71.702 Asbestos standard.
(a) Definitions. Asbestos is a generic term for a number of
asbestiform hydrated silicates that, when crushed or processed,
separate into flexible fibers made up of fibrils.
* * * * *
Asbestos fiber means a fiber of asbestos that meets the criteria of
a fiber.
* * * * *
(c) Measurement of airborne asbestos fiber concentration. Potential
asbestos fiber concentration shall be determined by phase contrast
microscopy (PCM) using the OSHA Reference Method in OSHA's asbestos
standard found in 29 CFR 1910.1001, Appendix A, or a method at least
equivalent to that method in identifying a potential asbestos exposure
exceeding the 0.1 f/cc full-shift limit or the 1 f/cc excursion limit.
When PCM results indicate a potential exposure exceeding the 0.1 f/cc
full-shift limit or the 1 f/cc excursion limit, samples shall be
further analyzed using transmission electron microscopy according to
NIOSH Method 7402 or a method at least equivalent to that method.
[FR Doc. E8-26440 Filed 11-6-08; 8:45 am]
BILLING CODE 4510-43-P