[Federal Register: November 28, 2008 (Volume 73, Number 230)]
[Rules and Regulations]
[Page 72310-72314]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr28no08-2]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2006-23605; Directorate Identifier 2005-NE-48-AD;
Amendment 39-15743; AD 2008-24-03]
RIN 2120-AA64
Airworthiness Directives; Rolls-Royce plc Models RB211 Trent 768-
60, Trent 772-60, and Trent 772B-60 Turbofan Engines
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule; request for comments.
-----------------------------------------------------------------------
SUMMARY: The FAA is superseding an existing airworthiness directive
(AD) for Rolls-Royce plc (RR) models RB211 Trent 768-60, Trent 772-60,
and Trent 772B-60 turbofan engines that have not incorporated RR
Service Bulletin (SB) No. RB.211-72-E708, SB No. RB.211-72-F227, or SB
No. RB.211-72-E965, at original issue or later revision. That AD
currently requires initial and repetitive borescope inspections of the
high-pressure/intermediate-pressure (HP/IP) turbine bearing internal
oil vent tube, scavenge tube, and tube heat shields for wear and
cracking, and removing tubes from service if found with any cracks
beyond serviceable limits. That AD also currently requires installation
of a new or modified HP/IP turbine bearings support as terminating
action for the repetitive borescope inspections. This AD has the same
requirements, and adds a repetitive inspection of the vent flow
restrictor for blockage. This AD results from RR revising their alert
service bulletin for inspection of the HP/IP turbine bearing internal
oil vent tube, scavenge tube, and tube heat shields for damage, to
include a repetitive inspection of the vent flow restrictor for
blockage. We are issuing this AD to prevent oil ejecting from the HP/IP
turbine bearings chamber and igniting. Burning oil can cause the
intermediate-pressure (IP) shaft to fracture, the IP turbine to
overspeed, and possible uncontained failure of the engine.
DATES: Effective December 15, 2008. The Director of the Federal
Register approved the incorporation by reference of certain
publications listed in the regulations as of December 15, 2008.
We must receive any comments on this AD by January 27, 2009.
ADDRESSES: Use one of the following addresses to comment on this AD.
Federal eRulemaking Portal: Go to http://
www.regulations.gov and follow the instructions for sending your
comments electronically.
Mail: Docket Management Facility, U.S. Department of
Transportation, 1200 New Jersey Avenue, SE., West Building Ground
Floor, Room W12-140, Washington, DC 20590-0001.
Hand Delivery: Deliver to Mail address above between 9
a.m. and 5 p.m., Monday through Friday, except Federal holidays.
Fax: (202) 493-2251.
Contact Rolls-Royce plc, PO Box 31, Derby, England, DE248BJ;
telephone: 011-44-1332-242424; fax: 011-44-1332-245418, for the service
information identified in this AD.
FOR FURTHER INFORMATION CONTACT: James Lawrence, Aerospace Engineer,
Engine Certification Office, FAA, Engine and Propeller Directorate, 12
New England Executive Park, Burlington, MA 01803; e-mail:
james.lawrence@faa.gov; telephone (781) 238-7175; fax (781) 238-7199.
[[Page 72311]]
SUPPLEMENTARY INFORMATION: On February 24, 2006, the FAA issued AD
2006-05-03, Amendment 39-14500 (71 FR 11153, March 6, 2006). That AD
requires initial and repetitive borescope inspections of the HP/IP
turbine bearing internal oil vent tube, scavenge tube, and tube heat
shields for wear and cracking, and removing tubes from service if found
with any cracks beyond serviceable limits. That AD also requires
installation of a new or modified HP/IP turbine bearings support as
terminating action for the repetitive borescope inspections. That AD
was the result of two reports of RR RB211 Trent 700 series engines
found with the HP/IP internal oil vent tube and scavenge tube fretted
by damaged heat shields on the tubes. That condition, if not corrected,
could result in oil ejecting from the HP/IP turbine bearings chamber
and igniting. Burning oil can cause the IP shaft to fracture, the IP
turbine to overspeed, and possible uncontained failure of the engine.
Actions Since AD 2006-05-03 Was Issued
Since AD 2006-05-03 was issued, the European Aviation Safety Agency
(EASA), which is the Technical Agent for the Member States of the
European Community, notified us that they issued EASA AD 2007-0255,
dated September 14, 2007, to supersede EASA AD 2005-0024, dated October
14, 2005. EASA AD 2007-0255 carries forward the requirements from EASA
AD 2005-0024. EASA AD 2007-0255 adds repetitive inspections of the vent
flow restrictor for blockage, based on RR issuing Alert Service
Bulletin (ASB) No. RB.211-72-AE792, Revision 3. ASB Revision 3, and now
Revision 4, add repetitive visual inspections of the vent flow
restrictor for blockage. This AD requires the same actions as EASA AD
2007-0255.
Relevant Service Information
We have reviewed and approved the technical contents of RR ASB No.
RB.211-72-AE792, Revision 4, dated August 2, 2007. That ASB describes
procedures for initial and repetitive borescope inspections of the HP/
IP turbine bearing internal oil vent tube, scavenge tube, and tube heat
shields for wear and cracking, and removing tubes from service if found
with any cracks beyond serviceable limits. That ASB also describes
procedures for performing repetitive inspections of the vent flow
restrictor for blockage. That ASB also references recently published RR
SB No. RB.211-72-F227 and RR SB No. RB.211-72-E965 as terminating
actions for the inspection requirements.
Bilateral Airworthiness Agreement
This engine model is manufactured in the United Kingdom and is type
certificated for operation in the United States under the provisions of
section 21.29 of the Federal Aviation Regulations (14 CFR 21.29) and
the applicable bilateral airworthiness agreement. Under this bilateral
airworthiness agreement, the EASA has kept the FAA informed of the
situation described above. We have examined the findings of the EASA,
reviewed all available information, and determined that AD action is
necessary for products of this type design that are certificated for
operation in the United States.
FAA's Determination and Requirements of This AD
Although no airplanes that are registered in the United States use
these RR RB211 Trent 768-60, Trent 772-60, and Trent 772B-60 turbofan
engines, the possibility exists that the engines could be used on
airplanes that are registered in the United States in the future. The
unsafe condition described previously is likely to exist or develop on
other RR RB211 Trent 768-60, Trent 772-60, and Trent 772B-60 turbofan
engines of the same type design. We are issuing this AD to prevent oil
ejecting from the HP/IP turbine bearings chamber and igniting. Burning
oil can cause the IP shaft to fracture, the IP turbine to overspeed,
and possible uncontained failure of the engine. This AD requires:
Initial and repetitive borescope inspections of the HP/IP
turbine bearing internal oil vent tube, scavenge tube, and tube heat
shields for wear and cracking; and
Removing tubes from service if found with any cracks
beyond serviceable limits; and
Performing repetitive inspections of the vent flow
restrictor for blockage; and
As terminating action to the repetitive inspections
required by the AD, at the next 05 module overhaul, but before May 31,
2010, removing the HP/IP bearings support and replacing with
serviceable parts.
You must use the service information described previously to
perform the inspections required by this AD.
FAA's Determination of the Effective Date
Since there are currently no domestic operators of this engine
model, notice and opportunity for public comment before issuing this AD
are unnecessary. Therefore, a situation exists that allows the
immediate adoption of this regulation.
Comments Invited
This AD is a final rule that involves requirements affecting flight
safety and was not preceded by notice and an opportunity for public
comment; however, we invite you to send us any written relevant data,
views, or arguments regarding this AD. Send your comments to an address
listed under ADDRESSES. Include ``AD Docket No. FAA-2006-23605;
Directorate Identifier 2005-NE-48-AD'' in the subject line of your
comments. We specifically invite comments on the overall regulatory,
economic, environmental, and energy aspects of the rule that might
suggest a need to modify it.
We will post all comments we receive, without change, to http://
www.regulations.gov, including any personal information you provide. We
will also post a report summarizing each substantive verbal contact
with FAA personnel concerning this AD. Using the search function of the
Web site, anyone can find and read the comments in any of our dockets,
including, if provided, the name of the individual who sent the comment
(or signed the comment on behalf of an association, business, labor
union, etc.). You may review the DOT's complete Privacy Act Statement
in the Federal Register published on April 11, 2000 (65 FR 19477-78).
Examining the AD Docket
You may examine the AD docket on the Internet at http://
www.regulations.gov; or in person at the Docket Operations office
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this AD, the regulatory evaluation,
any comments received, and other information. The street address for
the Docket Operations office (telephone (800) 647-5527) is the same as
the Mail address provided in the ADDRESSES section. Comments will be
available in the AD docket shortly after receipt.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures
[[Page 72312]]
the Administrator finds necessary for safety in air commerce. This
regulation is within the scope of that authority because it addresses
an unsafe condition that is likely to exist or develop on products
identified in this rulemaking action.
Regulatory Findings
We have determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national Government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a summary of the costs to comply with this AD and
placed it in the AD Docket. You may get a copy of this summary at the
address listed under ADDRESSES.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
0
Under the authority delegated to me by the Administrator, the Federal
Aviation Administration amends part 39 of the Federal Aviation
Regulations (14 CFR part 39) as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by removing Amendment 39-14500 71 FR
11153, March 6, 2006, and by adding a new airworthiness directive,
Amendment 39-15743, to read as follows:
2008-24-03 Rolls-Royce plc: Amendment 39-15743. Docket No. FAA-2006-
23605; Directorate Identifier 2005-NE-48-AD.
Effective Date
(a) This airworthiness directive (AD) becomes effective December
15, 2008.
Affected ADs
(b) This AD supersedes AD 2006-05-03, Amendment 39-14500.
Applicability
(c) This AD applies to Rolls-Royce plc (RR) models RB211 Trent
768-60, Trent 772-60, and Trent 772B-60 turbofan engines that have
not incorporated RR Service Bulletin (SB) No. RB.211-72-E708, SB No.
RB.211-72-F227, or SB No. RB.211-72-E965, at original issue or later
revision. These engines are installed on, but not limited to, Airbus
A330-243, A330-341, A330-342, and A330-343 airplanes.
Unsafe Condition
(d) This AD results from RR revising their alert service
bulletin for inspection of the high-pressure/intermediate-pressure
(HP/IP) turbine bearing internal oil vent tube, scavenge tube, and
tube heat shields for damage, to include a repetitive inspection of
the vent flow restrictor for blockage. We are issuing this AD to
prevent oil ejecting from the HP/IP turbine bearings chamber and
igniting. Burning oil can cause the intermediate-pressure (IP) shaft
to fracture, the IP turbine to overspeed, and possible uncontained
failure of the engine.
Compliance
(e) You are responsible for having the actions required by this
AD performed within the compliance times specified unless the
actions have already been done.
On-Wing Initial Borescope Inspection
(f) Borescope inspect and assess the condition of the HP/IP
turbine support assembly internal oil vent and scavenge tubes and
heat shields, using Section 3. of the Accomplishment Instructions
Part A, of RR Alert Service Bulletin (ASB) No. RB.211-72-AE792,
Revision 4, dated August 2, 2007, and Table 1 of this AD.
(g) The threshold life of the 05 module for the initial
borescope inspection is 10,000 operating hours since new or since
overhaul, or 2,500 cycles since new or since overhaul, whichever
occurs first.
Table 1--On-Wing Borescope Inspection Criteria
------------------------------------------------------------------------
For: Action:
------------------------------------------------------------------------
(1) 05 modules that exceed the threshold Inspect within 1 month after
life on the effective date of this AD: the effective date of this
AD.
(2) 05 modules that are below the Inspect by the threshold
threshold life on the effective date of life or within 3 months
this AD: from the effective date of
this AD, whichever occurs
later.
------------------------------------------------------------------------
On-Wing Repetitive Borescope Inspections
(h) Determine the serviceability and establish the repetitive
inspection intervals using Table 2 of this AD.
Table 2--Determination of Serviceability and Repetitive Inspection
Interval
------------------------------------------------------------------------
For: Action:
------------------------------------------------------------------------
(1) Outer heat shields of the vent or Re-inspect within intervals
scavenge tube with no visible damage: of 10,000 operating hours
or 2,500 cycles, whichever
occurs first.
(2) Outer heat shields of the vent or Re-inspect within intervals
scavenge tube with partial cracking up to of 6,400 operating hours or
90 degrees around the circumference or 10 1,600 cycles, whichever
mm along the length of either outer heat occurs first.
shield:
(3) Outer heat shields of the vent or Re-inspect within intervals
scavenge tube with partial cracking in of 1,600 operating hours or
excess of item (2) above, but less than 400 cycles, whichever
360 degrees around the circumference of occurs first.
either outer heat shield:
(4) Outer heat shields of the vent or Re-inspect or reject using
scavenge tube with cracking around the Table 3 of this AD.
complete circumference of either outer
heat shield, or if there is any missing
material from either outer heat shield:
------------------------------------------------------------------------
[[Page 72313]]
Table 3--Inspection and Rejection Criteria for Heat Shields Meeting
Conditions in Item (4) of Table 2 of This AD
------------------------------------------------------------------------
Condition: Action:
------------------------------------------------------------------------
(1) If the insulation blanket is in place Inspect within intervals of
inside the heat shield and preventing 1,600 operating hours or
fretting between the heat shield and the 400 cycles, whichever
tube. occurs first.
(2) If either vent or scavenge tube has Inspect within intervals of
fretting at the outer heat shield 400 operating hours or 100
position where the maximum depth of cycles, whichever occurs
fretting at any point around the full 360 first.
degrees of each tube is less than 0.46 mm
(0.018 inch).
(3) If it is not possible to determine the Reject from service within
maximum depth of fretting around the full 50 cycles of the inspection
360 degrees of each tube and item (1) being carried out.
above is not applicable, then the HP/IP
turbine support assembly must be rejected
from service.
(4) If either vent or scavenge tube has Reject within 10 cycles of
fretting at the outer heat shield the inspection being
position and the maximum depth of carried out.
fretting is greater than 0.46 mm (0.018
inch) then the HP/IP turbine support
assembly must be rejected from service.
------------------------------------------------------------------------
(i) For HP/IP turbine support assemblies which have been
previously inspected using the superseded AD, or this AD:
(1) Re-inspect the internal oil vent and scavenge tubes and heat
shields before exceeding the intervals established in Table 2 of
this AD.
(2) Determine the serviceability and intervals to the next
inspection using Table 2 of this AD.
Inspections of the Vent Flow Restrictor After On-Wing Borescope
Inspection
(j) After a high-power ground run or not later than 25 cycles
after heat shield inspection, inspect the vent flow restrictor,
using Section 3. of the Accomplishment Instructions of RR SB No.
RB.211-72-AE792, Revision 4, dated August 2, 2007.
Repetitive Inspections of the Vent Flow Restrictor After On-Wing
Borescope Inspection
(k) After each on-wing borescope inspection, specified in
paragraphs (f) through (h) of this AD, repeat the inspection of the
vent flow restrictor, as specified in paragraph (j) of this AD.
In-Shop Borescope Inspection
(l) For 05 modules in-shop which are not undergoing strip and
overhaul:
(1) Borescope inspect and assess the condition of the HP/IP
turbine support assembly internal oil vent and scavenge tubes and
heat shields.
(2) Inspect the vent tubes and the vent flow restrictor for
carbon, after performing a high-power ground run.
(3) Use Section 3. of the Accomplishment Instructions Part B, of
RR ASB No. RB.211-72-AE792, Revision 4, dated August 2, 2007, and
Table 4 of this AD to do the inspections.
(4) Determine the serviceability and establish the interval to
next inspection of the HP/IP turbine support assembly internal oil
vent and scavenge tubes and heat shields, using Table 4 of this AD:
Table 4--Re-Inspection Criteria
------------------------------------------------------------------------
For: Action:
------------------------------------------------------------------------
(i) Outer heat shields of the vent and Re-inspect at a threshold of
scavenge tubes with no visible damage: 10,000 operating hours time-
since-new or time-since-
overhaul, or 2,500 cycles-
since-new or cycles-since-
overhaul, whichever occurs
first.
(ii) Outer heat shields of the vent and Re-inspect at a not to
scavenge tubes with cracking up to 90 exceed interval of 6,400
degrees around the circumference or 10 mm operating hours or 1,600
along the length of either outer heat cycles, whichever occurs
shield: first.
(iii) Outer heat shields of the vent and Reject the tube and perform
scavenge tubes with visible cracking the terminating action
greater than 90 degrees of the specified in paragraph (n)
circumference or 10 mm along the length of this AD.
of either outer heat shield:
------------------------------------------------------------------------
(m) For 05 modules in-shop which are undergoing strip and
overhaul, carry out the terminating action specified in paragraph
(n) of this AD.
Terminating Action
(n) As terminating action to the repetitive inspections required
by this AD, at the next 05 module overhaul, but before May 31, 2010,
remove the affected HP/IP bearings supports and replace with
serviceable parts. Information on serviceable parts can be found in
RR SB No. RB.211-72-E708, Revision 2, dated September 6, 2005, or in
RR SB No. RB.211-72-F227, Revision 1, dated October 8, 2007, or in
RR SB No. RB.211-72-E965, Revision 1, dated October 4, 2005. To
obtain these SBs, see paragraph (r) of this AD for RR contact
information.
Definition
(o) For the purposes of this AD, serviceable parts are new or
reworked bearings supports which reduce the adverse effects of HP3
cooling air turbulence on the HP/IP turbine bearing internal oil
vent and scavenge tubes and tube heat shields, as described in RR SB
No. RB.211-72-E708, Revision 2, dated September 6, 2005, or in RR SB
No. RB.211-72-F227, Revision 1, dated October 8, 2007, or in RR SB
No. RB.211-72-E965, Revision 1, dated October 4, 2005.
Alternative Methods of Compliance
(p) The Manager, Engine Certification Office, has the authority
to approve alternative methods of compliance for this AD if
requested using the procedures found in 14 CFR 39.19.
Related Information
(q) European Aviation Safety Agency AD 2007-0255, dated
September 14, 2007, also addresses the subject of this AD.
Material Incorporated by Reference
(r) You must use the service information specified in Table 5 of
this AD to perform the inspections required by this AD. The Director
of the Federal Register approved the incorporation by reference of
the documents listed in Table 5 of this AD in accordance with 5
U.S.C. 552(a) and 1 CFR part 51. Contact Rolls-Royce plc, PO Box 31,
Derby, England, DE248BJ; telephone: 011-44-1332-242424; fax: 011-44-
1332-245418, for a copy of this service information. You may review
copies at the FAA, New England Region, 12 New England Executive
Park, Burlington, MA; or at the National Archives and Records
Administration (NARA). For information on the availability of this
material at NARA, call
[[Page 72314]]
202-741-6030, or go to: http://www.archives.gov/federal-register/
cfr/ibr-locations.html.
Table 5--Incorporation by Reference
----------------------------------------------------------------------------------------------------------------
Rolls-Royce Alert Service Bulletin No. Page Revision Date
----------------------------------------------------------------------------------------------------------------
RB.211-72-AE792, including Appendix A.. All...................... 4 August 2, 2007.
Total Pages: 31
----------------------------------------------------------------------------------------------------------------
Issued in Burlington, Massachusetts, on November 12, 2008.
Peter A. White,
Assistant Manager, Engine and Propeller Directorate, Aircraft
Certification Service.
[FR Doc. E8-27298 Filed 11-26-08; 8:45 am]
BILLING CODE 4910-13-P