[Federal Register Volume 73, Number 248 (Wednesday, December 24, 2008)] [Rules and Regulations] [Pages 78939-78944] From the Federal Register Online via the Government Publishing Office [www.gpo.gov] [FR Doc No: E8-30465] ----------------------------------------------------------------------- DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 39 [Docket No. FAA-2008-1328; Directorate Identifier 2008-CE-066-AD; Amendment 39-15776; AD 2008-26-10] RIN 2120-AA64 Airworthiness Directives; Cessna Aircraft Company 172, 175, 177, 180, 182, 185, 188, 206, 207, 208, 210, 303, 336, and 337 Series Airplanes AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Final rule; request for comments. ----------------------------------------------------------------------- SUMMARY: The FAA is adopting a new airworthiness directive (AD) for certain Cessna Aircraft Company (Cessna) 172, 175, 177, 180, 182, 185, 188, 206, 207, 208, 210, 303, 336, and 337 series airplanes. This AD requires you to inspect the alternate static air source selector valve to assure that the part number identification placard does not obstruct the alternate static air source selector valve port. If the part number identification placard obstructs the port, this AD also requires you to remove the placard, assure that the port is unobstructed, and report to the FAA if obstruction is found. This AD results from reports of airplanes found with alternate static air source selector valve port obstruction caused by improper installation of the part number identification placard. The actions specified by this AD are intended to prevent erroneous indications from the altimeter, airspeed, and vertical speed indicators, which could cause the pilot to react to incorrect flight information and possibly result in loss of control. DATES: This AD becomes effective on January 5, 2009. On January 5, 2009, the Director of the Federal Register approved the incorporation by reference of certain publications listed in this AD. We must receive any comments on this AD by February 23, 2009. ADDRESSES: Use one of the following addresses to comment on this AD.Federal eRulemaking Portal: Go to http://www.regulations.gov. Follow the instructions for submitting comments. Fax: (202) 493-2251. Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590. Hand Delivery: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. To get the service information identified in this AD, contact Cessna Aircraft Company, P.O. Box 7704, Wichita, Kansas 67277; telephone: (800) 423-7762 or (316) 517-6056; Internet: http://www.cessna.com. To view the comments to this AD, go to http://www.regulations.gov. The docket number is FAA-2008-1328; Directorate Identifier 2008-CE-066- AD. FOR FURTHER INFORMATION CONTACT: Ann Johnson, Aerospace Engineer, FAA, Wichita Aircraft Certification Office, 1801 Airport Road, Room 100, Wichita, Kansas 67209; telephone: 316-946-4105; fax: 316-946-4107; e- mail address: [email protected]. SUPPLEMENTARY INFORMATION: Discussion Reports of improper installation of the part number (P/N) identification placard on P/N 2013142-18 alternate static air source selector valves prompted us to issue AD 98-01-01, Amendment 39-10286 (63 FR 3455, January 23, 1998), which applies to certain Cessna Aircraft Company (Cessna) Models 172R and 182S airplanes, and AD 2008- 10-02, Amendment 39-155508 (73 FR 24168, May 2, 2008), which applies to certain Cessna 172, 175, 180, 182, 185, 206, 207, 208, 210, and 303 series airplanes. These ADs require inspecting the alternate static air source selector valve to determine if the P/N identification placard obstructs the alternate static air source selector valve port and removing [[Page 78940]] the placard if obstruction is found. These ADs also require reporting to the FAA if obstruction is found. These assemblies are required for flight into instrument flight rules (IFR) conditions as defined in Sec. 91.411 of the Federal Aviation Regulations (14 CFR 91.411). Use of these assemblies is optional in visual flight rules (VFR) conditions. After issuing AD 98-01-01 and AD 2008-10-02, we received reports of 15 airplanes not previously affected by either AD with a P/N 2013142-18 installed and the alternate static air source selector valve port was found obstructed by the P/N identification placard. We have been informed that all P/N 2013142-18 alternate static air source selector valves shipped from Cessna Parts Distribution between January 1, 1993, and March 31, 2008, may have port obstruction caused by the P/N identification placard. This condition, if not corrected, could result in the altimeter, airspeed, and vertical speed indicators displaying erroneous indications. This could cause the pilot to react to incorrect flight information and possibly result in loss of control. Relevant Service Information We reviewed Cessna Single Engine Service Bulletin, SB08-34-02, Revision 1, and Cessna Caravan Service Bulletin CAB08-4, Revision 1, both dated October 6, 2008; Cessna Single Engine Service Bulletin SEB08-5 and Cessna Multi-engine Service Bulletin MEB08-6, both dated October 13, 2008. The service information describes procedures for inspecting the alternate static air source selector valve to assure that the P/N identification placard does not obstruct the alternate static air source selector valve port. FAA's Determination and Requirements of This AD We are issuing this AD because we evaluated all the information and determined the unsafe condition described previously is likely to exist or develop on other products of the same type design. This AD requires inspecting the alternate static air source selector valve to assure that the P/N identification placard does not obstruct the alternate static air source selector valve port. If the P/N identification placard obstructs the port, this AD requires you to remove the placard, assure that the port is unobstructed, and report to the FAA if obstruction is found. FAA's Determination of the Effective Date Since an unsafe condition exists that requires the immediate adoption of this AD, we determined that notice and opportunity for public comment before issuing this AD are impracticable, and that good cause exists for making this amendment effective in fewer than 30 days. Comments Invited This AD is a final rule that involves requirements affecting flight safety, and we did not precede it by notice and an opportunity for public comment. We invite you to send any written relevant data, views, or arguments regarding this AD. Send your comments to an address listed under the ADDRESSES section. Include the docket number ``FAA-2008-1328; Directorate Identifier 2008-CE-066-AD'' at the beginning of your comments. We specifically invite comments on the overall regulatory, economic, environmental, and energy aspects of the AD. We will consider all comments received by the closing date and may amend the AD in light of those comments. We will post all comments we receive, without change, to http://www.regulations.gov, including any personal information you provide. We will also post a report summarizing each substantive verbal contact we receive concerning this AD. Authority for This Rulemaking Title 49 of the United States Code specifies the FAA's authority to issue rules on aviation safety. Subtitle I, Section 106, describes the authority of the FAA Administrator. Subtitle VII, Aviation Programs, describes in more detail the scope of the Agency's authority. We are issuing this rulemaking under the authority described in Subtitle VII, Part A, Subpart III, Section 44701, ``General requirements.'' Under that section, Congress charges the FAA with promoting safe flight of civil aircraft in air commerce by prescribing regulations for practices, methods, and procedures the Administrator finds necessary for safety in air commerce. This regulation is within the scope of that authority because it addresses an unsafe condition that is likely to exist or develop on products identified in this rulemaking action. Regulatory Findings We determined that this AD will not have federalism implications under Executive Order 13132. This AD will not have a substantial direct effect on the States, on the relationship between the national government and the States, or on the distribution of power and responsibilities among the various levels of government. For the reasons discussed above, I certify that this AD: (1) Is not a ``significant regulatory action'' under Executive Order 12866; (2) Is not a ``significant rule'' under DOT Regulatory Policies and Procedures (44 FR 11034, February 26, 1979); and (3) Will not have a significant economic impact, positive or negative, on a substantial number of small entities under the criteria of the Regulatory Flexibility Act. We prepared a regulatory evaluation of the estimated costs to comply with this AD and placed it in the AD docket. Examining the AD Docket You may examine the AD docket that contains the AD, the regulatory evaluation, any comments received, and other information on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. The Docket Office (telephone (800) 647-5527) is located at the street address stated in the ADDRESSES section. Comments will be available in the AD docket shortly after receipt. List of Subjects in 14 CFR Part 39 Air transportation, Aircraft, Aviation safety, Incorporation by reference, Safety. Adoption of the Amendment 0 Accordingly, under the authority delegated to me by the Administrator, the FAA amends 14 CFR part 39 as follows: PART 39--AIRWORTHINESS DIRECTIVES 0 1. The authority citation for part 39 continues to read as follows: Authority: 49 U.S.C. 106(g), 40113, 44701. Sec. 39.13 [Amended] 0 2. The FAA amends Sec. 39.13 by adding a new AD to read as follows: 2008-26-10 Cessna Aircraft Company: Amendment 39-15776; Docket No. FAA-2008-1328; Directorate Identifier 2008-CE-066-AD. Effective Date (a) This AD becomes effective on January 5, 2009. Affected ADs (b) This AD relates to AD 98-01-01, Amendment 39-10287 and AD 2008-10-02, Amendment 39-15508. These ADs can be found on the Internet at the following Web site: http://rgl.faa.gov/. [[Page 78941]] Applicability (c) This AD applies to all serial numbers (S/Ns) of the airplanes listed in Table 1 of this AD, certificated in any category, that: (1) Were initially delivered from the manufacturer between January 1, 1993, and March 31, 2008, unless the modification/rework required in AD 2008-10-02 has been done and you remain in compliance with that AD; or (2) Have a part number (P/N) 2013142-18 installed as a replacement part anytime after January 1, 1993, unless the modification/rework required in AD 2008-10-02 has been done and you remain in compliance with that AD. Note 1: The affected part was shipped from Cessna Parts Distribution (CPD) between January 1, 1993, and March 31, 2008. Note 2: P/N 2013142-18 replaced P/Ns 2013142-9, -13, and -17. Table 1--Applicable Airplane Models ---------------------------------------------------------------------------------------------------------------- ---------------------------------------------------------------------------------------------------------------- Models ---------------------------------------------------------------------------------------------------------------- 172 F172K 177 172A F172L 177A 172B F172M 177B 172C F172N 177RG 172D F172P F177RG 172E FR172E 180 172F (USAF T-41A) FR172F 180A 172G FR172G 180B 172H (USAF T-41A) FR172H 180C 172I FR172J 180D 172K FR172K 180E 172L P172D 180F 172M R172E (USAF T-41B), (USAF T-41C and 180G D) 172N R172F (USAF T-41) 180H 172P R172G (USAF T-41C or D) 180J 172Q R172H (USAF T-41D) 180K 172R R172J 182 172S R172K 182A F172D 172RG 182B F172E 175 182C F172F 175A 182D F172G 175B 182E F172H 175C 182F 182G A185F U206D 182H 206 U206E 182J 206H U206F 182K P206 U206G 182L P206A 207 182M P206B 207A 182N P206C T207 182P P206D T207A 182Q P206E 208 182R T206H 208B 182S TP206A 210 182T TP206B 210A F182P TP206C 210B F182Q TP206D 210C FR182 TP206E 210D R182 TU206A 210E T182 TU206B 210F T182T TU206C 210G TR182 TU206D 210H 185 TU206E 210J 185A TU206F 210K 185B TU206G 210L 185C U206 210M 185D U206A 210N 185E U206B 210R A185E U206C 210-5 (205) 210-5A (205A) FT337F T210F M337B (USAF 02A) T210G T337B T210H T337C T210J T337D T210K T337E T210L T337F T210M T337H T210N T337H-SP T210R T303 336 337 337A (USAF 02B) [[Page 78942]] 337B 337C 337D 337E 337F 337G 337H F337E F337F F337G F337H FT337E ---------------------------------------------------------------------------------------------------------------- Unsafe Condition (e) This AD is the result of reports of improper installation of the part number identification placard on the alternate static air source selector valve. We are issuing this AD to prevent erroneous indications from the altimeter, airspeed, and vertical speed indicators, which could cause the pilot to react to incorrect flight information and possibly result in loss of control. Compliance (e) To address this problem, you must do the following, unless already done. A person authorized to perform maintenance as specified in 14 CFR section 43.3 of the Federal Aviation Administration Regulations (14 CFR 43.3) is required to do all the actions required in this AD. ------------------------------------------------------------------------ Actions Compliance Procedures ------------------------------------------------------------------------ (1) For all affected Within the next 100 Following the airplanes that are not hours time-in- procedures in equipped for flight under service (TIS) after Cessna Single instrument flight rules January 5, 2009 Engine Service (IFR): Inspect the (the effective date Bulletin SB08-34- alternate static air source of this AD) or 02, Revision 1, selector valve to assure within the next 4 dated October 6, that the part number months after 2008; Cessna identification placard is January 5, 2009 Caravan Service not obstructing the port. (the effective date Bulletin CAB08-4, of this AD), Revision 1, dated whichever occurs October 6, 2008; first. Cessna Single Engine Service Bulletin SEB08-5, dated October 13, 2008; or Cessna Multi-engine Service Bulletin MEB08-6, dated October 13, 2008, as applicable. (2) For all affected (A) Inspect within Following the airplanes that are equipped the next 10 days procedures in for flight under instrument after January 5, Cessna Single flight rules (IFR): 2009 (the effective Engine Service date of this AD); Bulletin SB08-34- or 02, Revision 1, (B) Install placards dated October 6, before further 2008; Cessna flight after Caravan Service January 5, 2009 Bulletin CAB08-4, (the effective date Revision 1, dated of this AD). October 6, 2008; Cessna Single Engine Service Bulletin SEB08-5, dated October 13, 2008; or Cessna Multi-engine Service Bulletin MEB08-6, dated October 13, 2008, as applicable. (i) Inspect the alternate static air source selector valve to assure that the part number identification placard is not obstructing the port; or (ii) Fabricate a placard that incorporates the following words (using at least \1/8\-inch letters) and install this placard on the instrument panel within the pilot's clear view: ``IFR OPERATION IS PROHIBITED'' and ``USE OF THE ALTERNATE STATIC AIR SOURCE IS PROHIBITED.'' (3) For all affected Within the next 100 Following the airplanes that are equipped hours TIS after procedures in for flight under instrument January 5, 2009 Cessna Single flight rules (IFR): If (the effective date Engine Service placards were installed in of this AD) or Bulletin SB08-34- accordance with paragraph within the next 4 02, Revision 1, (e)(2)(ii) of this AD, months after dated October 6, inspect the alternate January 5, 2009 2008; Cessna static air source selector (the effective date Caravan Service valve to assure that the of this AD), Bulletin CAB08-4, part number identification whichever occurs Revision 1, dated placard is not obstructing first. After doing October 6, 2008; the port. the inspection, Cessna Single remove the placards Engine Service installed in Bulletin SEB08-5, accordance with dated October 13, paragraph 2008; or Cessna (e)(2)(ii) of this Multi-engine AD before further Service Bulletin flight. MEB08-6, dated October 13, 2008, as applicable. (4) For all affected Before further Following the airplanes: If the alternate flight after the procedures in static air source selector inspection required Cessna Single valve port is found in paragraphs Engine Service obstructed by the part (e)(1), (e)(2)(i), Bulletin SB08-34- number identification and (e)(3) of this 02, Revision 1, placard during the AD. dated October 6, inspection required in 2008; Cessna paragraphs (e)(1), Caravan Service (e)(2)(i), and (e)(3) of Bulletin CAB08-04, this AD, remove the placard Revision 1, dated from the valve body, October 6, 2008; discard the placard, and Cessna Single assure that the port is Engine Service open and unobstructed. Bulletin SEB08-5, dated October 13, 2008; or Cessna Multi-engine Service Bulletin MEB08-6, dated October 13, 2008, as applicable. [[Page 78943]] (5) For all affected As of 10 days after A person authorized airplanes: When a January 5, 2009 to perform replacement valve is (the effective date maintenance as needed, only install a P/N of this AD). specified in 14 CFR 2013142-18 alternate static section 43.3 of the air source selector valve Federal Aviation that has been inspected and Administration the port is found free from Regulations (14 CFR obstruction. 43.3) is required to do the inspection. ------------------------------------------------------------------------ (f) Report to the FAA the results of the inspection required by this AD where an obstruction was found. (1) Submit this report within 10 days after the inspection or 10 days after the effective date of this AD, whichever occurs later. (2) Use the form in Figure 1 of this AD and submit it to FAA, Manufacturing Inspection District Office, Mid-Continent Airport, 1804 Airport Road, Room 101, Wichita, Kansas 67209; or fax to (316) 946-4189. (3) The Office of Management and Budget (OMB) approved the information collection requirements contained in this regulation under the provisions of the Paperwork Reduction Act of 1980 (44 U.S.C. 3501 et seq.) and assigned OMB Control Number 2120-0056. BILLING CODE 4910-13-P [GRAPHIC] [TIFF OMITTED] TR24DE08.000 BILLING CODE 4910-13-C [[Page 78944]] Alternative Methods of Compliance (AMOCs) (g) The Manager, Wichita Aircraft Certification Office (ACO), FAA, has the authority to approve AMOCs for this AD, if requested using the procedures found in 14 CFR 39.19. Send information to ATTN: Ann Johnson, Aerospace Engineer, FAA, Wichita ACO, 1801 Airport Road, Room 100, Wichita, Kansas 67209; telephone: 316-946- 4105; fax: 316-946-4107; e-mail address: [email protected]. Before using any approved AMOC on any airplane to which the AMOC applies, notify your appropriate principal inspector (PI) in the FAA Flight Standards District Office (FSDO), or lacking a PI, your local FSDO. (h) AMOCs approved for AD 2008-10-02 are approved for this AD. Material Incorporated by Reference (i) You must use Cessna Single Engine Service Bulletin, SB08-34- 02, Revision 1, dated October 6, 2008; Cessna Caravan Service Bulletin CAB08-4, Revision 1, dated October 6, 2008; Cessna Single Engine Service Bulletin SEB08-5, dated October 13, 2008; and Cessna Multi-engine Service Bulletin MEB08-6, dated October 13, 2008, to do the actions required by this AD, unless the AD specifies otherwise. (1) The Director of the Federal Register approved the incorporation by reference of this service information under 5 U.S.C. 552(a) and 1 CFR part 51. (2) For service information identified in this AD, contact Cessna Aircraft Company, P.O. Box 7704, Wichita, Kansas 67277; telephone: (800) 423-7762 or (316) 517-6056; Internet: http://www.cessna.com. (3) You may review copies at the FAA, Central Region, Office of the Regional Counsel, 901 Locust, Kansas City, Missouri 64106; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202- 741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html. Issued in Kansas City, Missouri, on December 15, 2008. Kim Smith, Manager, Small Airplane Directorate, Aircraft Certification Service. [FR Doc. E8-30465 Filed 12-23-08; 8:45 am] BILLING CODE 4910-13-P