[Federal Register: May 1, 2008 (Volume 73, Number 85)]
[Proposed Rules]
[Page 23995-23997]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr01my08-17]
[[Page 23995]]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2008-0179; Directorate Identifier 2007-NM-367-AD]
RIN 2120-AA64
Airworthiness Directives; Bombardier Model DHC-8-102, DHC-8-103,
DHC-8-106, DHC-201, DHC-8-202, DHC-8-301, DHC-8-311, and DHC-8-315
Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Supplemental notice of proposed rulemaking (NPRM); reopening of
comment period.
-----------------------------------------------------------------------
SUMMARY: We are revising an earlier NPRM for the products listed above.
This action revises the earlier NPRM by expanding the scope. This
proposed AD results from mandatory continuing airworthiness information
(MCAI) originated by an aviation authority of another country to
identify and correct an unsafe condition on an aviation product. The
MCAI describes the unsafe condition as:
Bombardier Aerospace has completed a system safety review of the
aircraft fuel system against fuel tank safety standards * * *.
[A]ssessment showed that supplemental maintenance tasks
[inspections of fuel tank bonding jumpers, wiring harnesses, and
drain valve components, among other items and actions; and
applicable corrective actions] are required to prevent potential
ignition sources inside the fuel system, which could result in a
fuel tank explosion. * * *
The proposed AD would require actions that are intended to address the
unsafe condition described in the MCAI.
DATES: We must receive comments on this proposed AD by May 21, 2008.
ADDRESSES: You may send comments by any of the following methods:
Federal eRulemaking Portal: Go to http://
www.regulations.gov. Follow the instructions for submitting comments.
Fax: (202) 493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue, SE., Washington, DC 20590.
Hand Delivery: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-40, 1200 New
Jersey Avenue, SE., Washington, DC, between 9 a.m. and 5 p.m., Monday
through Friday, except Federal holidays.
Examining the AD Docket
You may examine the AD docket on the Internet at http://
www.regulations.gov; or in person at the Docket Operations office
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this proposed AD, the regulatory
evaluation, any comments received, and other information. The street
address for the Docket Operations office (telephone (800) 647-5527) is
in the ADDRESSES section. Comments will be available in the AD docket
shortly after receipt.
FOR FURTHER INFORMATION CONTACT: Rocco Viselli, Aerospace Engineer,
Airframe and Propulsion Branch, ANE-171, FAA, New York Aircraft
Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New
York 11590; telephone (516) 228-7331; fax (516) 794-5531.
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to send any written relevant data, views, or
arguments about this proposed AD. Send your comments to an address
listed under the ADDRESSES section. Include ``Docket No. FAA-2008-0179;
Directorate Identifier 2007-NM-367-AD'' at the beginning of your
comments. We specifically invite comments on the overall regulatory,
economic, environmental, and energy aspects of this proposed AD. We
will consider all comments received by the closing date and may amend
this proposed AD based on those comments.
We will post all comments we receive, without change, to http://
www.regulations.gov, including any personal information you provide. We
will also post a report summarizing each substantive verbal contact we
receive about this proposed AD.
Discussion
We proposed to amend 14 CFR part 39 with an earlier NPRM for the
specified products, which was published in the Federal Register on
February 19, 2008 (73 FR 9055). That earlier NPRM proposed to require
actions intended to address the unsafe condition for the products
listed above.
Since that earlier NPRM was issued, we have determined that for
certain airplanes the initial compliance times for doing the tasks
specified in paragraph (f)(1) of the earlier NPRM must be reduced. That
earlier NPRM resulted from Canadian Airworthiness Directive CF-2007-32,
dated December 17, 2007 (referred to after this as ``the MCAI'').
The MCAI does not provide an initial compliance time for doing the
tasks for certain airplanes. For those airplanes, in the earlier NPRM
we proposed an initial compliance time that started from the effective
date of the AD; or the date of issuance of the original Canadian
standard airworthiness certificate or the date of issuance of the
original Canadian export certificate of airworthiness; whichever occurs
later. Although unstated in the MCAI, we have determined that the
intent of the MCAI is for the initial compliance time to start from the
initial delivery date of the airplane in order to address the
identified unsafe condition in a timely manner. We have also revised
the initial compliance times for clarity by providing a threshold and
grace period for each task. We have revised this supplemental NPRM by
adding Table 2 to specify the initial compliance times for each task.
You may obtain further information by examining the MCAI in the AD
docket.
FAA's Determination and Requirements of This Proposed AD
This product has been approved by the aviation authority of another
country, and is approved for operation in the United States. Pursuant
to our bilateral agreement with the State of Design Authority, we have
been notified of the unsafe condition described in the MCAI and service
information referenced above. We are proposing this AD because we
evaluated all pertinent information and determined an unsafe condition
exists and is likely to exist or develop on other products of the same
type design.
Certain changes described above expand the scope of the earlier
NPRM. As a result, we have determined that it is necessary to reopen
the comment period to provide additional opportunity for the public to
comment on this proposed AD.
Differences Between This AD and the MCAI or Service Information
We have reviewed the MCAI and related service information and, in
general, agree with their substance. But we might have found it
necessary to use different words from those in the MCAI to ensure the
AD is clear for U.S. operators and is enforceable. In making these
changes, we do not intend to differ substantively from the information
provided in the MCAI and related service information.
We might also have required different actions in this AD from those
in the MCAI in order to follow our FAA policies. Any such differences
are highlighted in a NOTE within the AD.
[[Page 23996]]
Costs of Compliance
Based on the service information, we estimate that this proposed AD
would affect about 122 products of U.S. registry. We also estimate that
it would take about 1 work-hour per product to comply with the basic
requirements of this proposed AD. The average labor rate is $80 per
work-hour. Based on these figures, we estimate the cost of the proposed
AD on U.S. operators to be $9,760, or $80 per product.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's
authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, Part A, Subpart III, Section 44701: General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this proposed AD and placed it in the AD docket.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. The FAA amends Sec. 39.13 by adding the following new AD:
Bombardier, Inc. (Formerly de Havilland, Inc.): Docket No. FAA-2008-
0179; Directorate Identifier 2007-NM-367-AD.
Effective Date
(a) We must receive comments by May 21, 2008.
Affected ADs
(b) None.
Applicability
(c) This AD applies to all Bombardier Model DHC-8-102, DHC-8-
103, DHC-8-106, DHC-201, DHC-8-202, DHC-8-301, DHC-8-311, and DHC-8-
315 airplanes, certificated in any category, all serial numbers.
Note 1: This AD requires revisions to certain operator
maintenance documents to include new inspections. Compliance with
these inspections is required by 14 CFR 91.403(c). For airplanes
that have been previously modified, altered, or repaired in the
areas addressed by these inspections, the operator may not be able
to accomplish the inspections described in the revisions. In this
situation, to comply with 14 CFR 91.403(c), the operator must
request approval for an alternative method of compliance according
to paragraph (g) of this AD. The request should include a
description of changes to the required inspections that will ensure
the continued operational safety of the airplane.
Subject
(d) Air Transport Association (ATA) of America Code 28: Fuel.
Reason
(e) The mandatory continuing airworthiness information (MCAI)
states:
Bombardier Aerospace has completed a system safety review of the
aircraft fuel system against fuel tank standards introduced in
Chapter 525 of the Airworthiness Manual through Notice of Proposed
Amendment (NPA) 2002-043. The identified non-compliances were then
assessed using Transport Canada Policy Letter No. 525-001, to
determine if mandatory corrective action is required.
The assessment showed that supplemental maintenance tasks
[inspections of fuel tank bonding jumpers, wiring harnesses, and
drain valve components, among other items and actions; and
applicable corrective actions] are required to prevent potential
ignition sources inside the fuel system, which could result in a
fuel tank explosion. Revisions have been made to Part 2
``Airworthiness Limitations List'' of the DHC-8 Maintenance Program
Manuals to introduce the required maintenance tasks.
The corrective action is revising the Airworthiness Limitations
Section of the Instructions for Continued Airworthiness to
incorporate new limitations for fuel tank systems.
Actions and Compliance
(f) Unless already done, do the following actions.
(1) Within 60 days after the effective date of this AD, or
before December 16, 2008, whichever occurs first, revise the
Airworthiness Limitations Section (ALS) of the Instructions for
Continued Airworthiness to incorporate the fuel system limitations
tasks identified in the de Havilland temporary revisions (TRs) to
Part 2 ``Airworthiness Limitations List'' of the Dash 8 Series
Maintenance Program Manuals (``the MPMs''). The TRs are listed in
Table 1 of this AD. For the tasks identified in the TRs, the initial
compliance times start at the later of the applicable ``Threshold''
and ``Grace Period'' times specified in Table 2 of this AD, and the
repetitive limitation tasks must be accomplished thereafter at the
interval specified in the TRs to the MPM, except as provided by
paragraphs (f)(2), (f)(3), (f)(4), and (g)(1) of this AD.
Table 1.--Temporary Revisions
------------------------------------------------------------------------
Model de Havilland TR MPM
------------------------------------------------------------------------
DHC-8-102, DHC-8-103, and DHC- AWL-110, dated Dash 8 Series 100
8-106 airplanes. August 31, 2007. MPM, Product Support
Manual (PSM) 1-8-7,
Part 2,
``Airworthiness
Limitations List''.
DHC-8-201, and DHC-8-202 AWL 2-43, dated Dash 8 Series 200
airplanes. August 31, 2007. MPM, PSM 1-82-7,
Part 2,
``Airworthiness
Limitations List''.
DHC-8-301, DHC-8-311, and DHC- AWL 3-109, dated Dash 8 Series 300
8-315 airplanes. August 31, 2007. MPM, PSM 1-83-7,
Part 2,
``Airworthiness
Limitations List''.
------------------------------------------------------------------------
[[Page 23997]]
Table 2.--Initial Inspections
------------------------------------------------------------------------
Compliance time (whichever occurs later)
Description -------------------------------------------
Threshold Grace period
------------------------------------------------------------------------
Tasks with 6,000 flight Before the Within 2,000 flight
hours/36 month intervals. accumulation of hours or 12 months
6,000 total flight after the effective
hours, or within 36 date of this AD,
months since new, whichever occurs
whichever occurs first.
first.
Tasks with 18,000 flight Before the Within 6,000 flight
hours/108 month intervals. accumulation of hours or 36 months
18,000 total flight after the effective
hours, or within date of this AD,
108 months since whichever occurs
new, whichever first.
occurs first.
Tasks with 72,000 flight Before the Within 600 flight
hours/36 year intervals. accumulation of hours or 3 months
72,000 total flight after the effective
hours, or within 36 date of this AD,
years since new, whichever occurs
whichever occurs first.
first.
------------------------------------------------------------------------
Note 2: The actions required by paragraph (f)(1) of this AD may
be done by inserting a copy of the applicable TR listed in Table 1
of this AD into the Airworthiness Limitations section of the
applicable MPM listed in Table 1 of this AD. When the applicable TR
has been included in general revisions of the applicable MPM, the
general revisions may be inserted in the MPM, provided the relevant
information in the general revision is identical to that in the
applicable TR.
(2) For those tasks with 6,000 flight hours/36 month limitation
task intervals: For airplanes that have accumulated 4,000 total
flight hours or more, or 24 months or more since new, as of the
effective date of this AD, do the initial limitation tasks within
2,000 flight hours or 12 months after the effective date of this AD,
whichever occurs first. Thereafter, repeat the limitation tasks at
intervals not to exceed 6,000 flight hours or 36 months, whichever
occurs first.
(3) For those tasks with 18,000 flight hours/108 month
limitation task intervals: For airplanes that have accumulated
12,000 total flight hours or more, or 72 months or more since new,
as of the effective date of this AD, do the initial limitation tasks
within 6,000 flight hours or 36 months after the effective date of
this AD, whichever occurs first. Thereafter, repeat the limitation
tasks at intervals not to exceed 18,000 flight hours or 108 months,
whichever occurs first.
(4) After accomplishing the actions specified in paragraphs
(f)(1), (f)(2), and (f)(3) of this AD, no alternative inspections/
limitation tasks or inspection/limitation task intervals may be used
unless the inspections/limitation tasks or inspection/limitation
task intervals are part of a later revision of Part 2
``Airworthiness Limitations List'' of the applicable de Havilland
Dash 8 Series MPM listed in Table 3 of this AD, that is approved by
the Manager, New York Aircraft Certification Office (ACO), FAA, or
the Transport Canada Civil Aviation (TCCA) (or its delegated agent);
or unless inspections/limitation tasks or inspection/limitation task
intervals are approved as an alternative method of compliance (AMOC)
in accordance with the procedures specified in paragraph (g)(1) of
this AD.
Table 3.--Maintenance Program Manuals
------------------------------------------------------------------------
Model MPM
------------------------------------------------------------------------
DHC-8-102, DHC-8-103, and DHC- Dash 8 Series 100 MPM, PSM 1-8-7, Part 2,
8-106 airplanes. ``Airworthiness Limitations List,''
Revision 17, dated April 19, 2005.
DHC-8-201, and DHC-8-202 Dash 8 Series 200 MPM, PSM 1-82-7, Part
airplanes. 2, ``Airworthiness Limitations List,''
Revision 5, dated August 15, 2001.
DHC-8-301, DHC-8-311, and DHC- Dash 8 Series 300 MPM, PSM 1-83-7, Part
8-315 airplanes. 2, ``Airworthiness Limitations List,''
Revision 16, dated August 15, 2001.
------------------------------------------------------------------------
FAA AD Differences
Note 3: This AD differs from the MCAI and/or service information
as follows: No differences.
Other FAA AD Provisions
(g) The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, New
York ACO, FAA, has the authority to approve AMOCs for this AD, if
requested using the procedures found in 14 CFR 39.19. Send
information to ATTN: Rocco Viselli, Aerospace Engineer, Airframe and
Propulsion Branch, ANE-171, FAA, New York Aircraft Certification
Office, 1600 Stewart Avenue, Suite 410, Westbury, New York 11590;
telephone (516) 228-7331; fax (516) 794-5531. Before using any
approved AMOC on any airplane to which the AMOC applies, notify your
appropriate principal inspector (PI) in the FAA Flight Standards
District Office (FSDO), or lacking a PI, your local FSDO.
(2) Airworthy Product: For any requirement in this AD to obtain
corrective actions from a manufacturer or other source, use these
actions if they are FAA-approved. Corrective actions are considered
FAA-approved if they are approved by the State of Design Authority
(or their delegated agent). You are required to assure the product
is airworthy before it is returned to service.
(3) Reporting Requirements: For any reporting requirement in
this AD, under the provisions of the Paperwork Reduction Act, the
Office of Management and Budget (OMB) has approved the information
collection requirements and has assigned OMB Control Number 2120-
0056.
Related Information
(h) Refer to MCAI Canadian Airworthiness Directive CF-2007-32,
dated December 17, 2007, and the temporary revisions listed in Table
1 of this AD.
Issued in Renton, Washington, on April 24, 2008.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E8-9575 Filed 4-30-08; 8:45 am]
BILLING CODE 4910-13-P