[Federal Register: May 20, 2009 (Volume 74, Number 96)]
[Notices]
[Page 23695-23701]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr20my09-46]
-----------------------------------------------------------------------
ENVIRONMENTAL PROTECTION AGENCY
[EPA-HQ-OPPT-2009-0281; FRL-8413-1]
Certain New Chemicals; Receipt and Status Information
AGENCY: Environmental Protection Agency (EPA).
ACTION: Notice.
-----------------------------------------------------------------------
SUMMARY: Section 5 of the Toxic Substances Control Act (TSCA) requires
any person who intends to manufacture (defined by statute to include
import) a new chemical (i.e., a chemical not on the TSCA Inventory) to
notify EPA and comply with the statutory provisions pertaining to the
manufacture of new chemicals. Under sections 5(d)(2) and 5(d)(3) of
TSCA, EPA is required to publish a notice of receipt of a
premanufacture notice (PMN) or an application for a test marketing
exemption (TME), and to publish periodic status reports on the
chemicals under review and the receipt of notices of commencement to
manufacture those chemicals. This status report, which covers the
period from March 23, 2009 through April 10, 2009, consists of the PMNs
and TME, both pending or
[[Page 23696]]
expired, and the notices of commencement to manufacture a new chemical
that the Agency has received under TSCA section 5 during this time
period. Premanufacturer Notices P09-87 thru P09-129 which covered the
time period of December 2, 2008 through December 18, 2008 were
inadvertaly left out of the Federal Register and are included in this
notice.
DATES: Comments identified by the specific PMN number or TME number,
must be received on or before June 19, 2009.
ADDRESSES: Submit your comments, identified by docket identification
(ID) number EPA-HQ-OPPT-2009-0281, by one of the following methods:
Federal eRulemaking Portal: http://www.regulations.gov.
Follow the on-line instructions for submitting comments.
Mail: Document Control Office (7407M), Office of Pollution
Prevention and Toxics (OPPT), Environmental Protection Agency, 1200
Pennsylvania Ave., NW., Washington, DC 20460-0001.
Hand Delivery: OPPT Document Control Office (DCO), EPA
East Bldg., Rm. 6428, 1201 Constitution Ave., NW., Washington, DC.
Attention: Docket ID Number EPA-HQ-OPPT-2009-0281. The DCO is open from
8 a.m. to 4 p.m., Monday through Friday, excluding legal holidays. The
telephone number for the DCO is (202) 564-8930. Such deliveries are
only accepted during the DCO's normal hours of operation, and special
arrangements should be made for deliveries of boxed information.
Instructions: Direct your comments to docket ID number EPA-HQ-OPPT-
2009-0281. EPA's policy is that all comments received will be included
in the docket without change and may be made available on-line at
http://www.regulations.gov, including any personal information
provided, unless the comment includes information claimed to be
Confidential Business Information (CBI) or other information whose
disclosure is restricted by statute. Do not submit information that you
consider to be CBI or otherwise protected through regulations.gov or e-
mail. The regulations.gov website is an ``anonymous access'' system,
which means EPA will not know your identity or contact information
unless you provide it in the body of your comment. If you send an e-
mail comment directly to EPA without going through regulations.gov,
your e-mail address will be automatically captured and included as part
of the comment that is placed in the docket and made available on the
Internet. If you submit an electronic comment, EPA recommends that you
include your name and other contact information in the body of your
comment and with any disk or CD-ROM you submit. If EPA cannot read your
comment due to technical difficulties and cannot contact you for
clarification, EPA may not be able to consider your comment. Electronic
files should avoid the use of special characters, any form of
encryption, and be free of any defects or viruses. For additional
information about EPA's public docket, visit the EPA Docket Center
homepage at http://www.epa.gov/epahome/dockets.htm.
Docket: All documents in the docket are listed in the docket index
available in regulations.gov. To access the electronic docket, go to
http://www.regulations.gov, select ``Advanced Search,'' then ``Docket
Search.'' Insert the docket ID number where indicated and select the
``Submit'' button. Follow the instructions on the regulations.gov
website to view the docket index or access available documents.
Although listed in the index, some information is not publicly
available, e.g., CBI or other information whose disclosure is
restricted by statute. Certain other material, such as copyrighted
material, will be publicly available only in hard copy. Publicly
available docket materials are available electronically at http://
www.regulations.gov, or, if only available in hard copy, at the OPPT
Docket. The OPPT Docket is located in the EPA Docket Center (EPA/DC) at
Rm. 3334, EPA West Bldg., 1301 Constitution Ave., NW., Washington, DC.
The EPA/DC Public Reading Room hours of operation are 8:30 a.m. to 4:30
p.m., Monday through Friday, excluding Federal holidays. The telephone
number of the EPA/DC Public Reading Room is (202) 566-1744, and the
telephone number for the OPPT Docket is (202) 566-0280. Docket visitors
are required to show photographic identification, pass through a metal
detector, and sign the EPA visitor log. All visitor bags are processed
through an X-ray machine and subject to search. Visitors will be
provided an EPA/DC badge that must be visible at all times in the
building and returned upon departure.
FOR FURTHER INFORMATION CONTACT: Colby Lintner, Regulatory Coordinator,
Environmental Assistance Division, Office of Pollution Prevention and
Toxics (7408M), Environmental Protection Agency, 1200 Pennsylvania
Ave., NW., Washington, DC 20460-0001; telephone number: (202) 554-1404;
e-mail address: TSCA-Hotline@epa.gov.
SUPPLEMENTARY INFORMATION:
I. General Information
A. Does this Action Apply to Me?
This action is directed to the public in general. As such, the
Agency has not attempted to describe the specific entities that this
action may apply to. Although others may be affected, this action
applies directly to the submitter of the premanufacture notices
addressed in the action. If you have any questions regarding the
applicability of this action to a particular entity, consult the person
listed under FOR FURTHER INFORMATION CONTACT.
B. What Should I Consider as I Prepare My Comments for EPA?
1. Submitting CBI. Do not submit this information to EPA through
regulations.gov or e-mail. Clearly mark the part or all of the
information that you claim to be CBI. For CBI information in a disk or
CD-ROM that you mail to EPA, mark the outside of the disk or CD-ROM
that you mail to EPA, mark the outside of the disk or CD-ROM as CBI and
then identify electronically within the disk or CD-ROM the specific
information that is claimed as CBI. In addition to one complete version
of the comment that includes information claimed as CBI, a copy of the
comment that does not contain the information claimed as CBI must be
submitted for inclusion in the public docket. Information so marked
will not be disclosed except in accordance with procedures set forth in
40 CFR part 2.
2. Tips for preparing your comments. When submitting comments,
remember to:
i. Identify the document by docket ID number and other identifying
information (subject heading, Federal Register date and page number).
ii. Follow directions. The Agency may ask you to respond to
specific questions or organize comments by referencing a Code of
Federal Regulations (CFR) part or section number.
iii. Explain why you agree or disagree; suggest alternatives and
substitute language for your requested changes.
iv. Describe any assumptions and provide any technical information
and/or data that you used.
v. If you estimate potential costs or burdens, explain how you
arrived at your estimate in sufficient detail to allow for it to be
reproduced.
vi. Provide specific examples to illustrate your concerns and
suggest alternatives.
vii. Explain your views as clearly as possible, avoiding the use of
profanity or personal threats.
[[Page 23697]]
viii. Make sure to submit your comments by the comment period
deadline identified.
II. Why is EPA Taking this Action?
Section 5 of TSCA requires any person who intends to manufacture
(defined by statute to include import) a new chemical (i.e., a chemical
not on the TSCA Inventory to notify EPA and comply with the statutory
provisions pertaining to the manufacture of new chemicals. Under
sections 5(d)(2) and 5(d)(3) of TSCA, EPA is required to publish a
notice of receipt of a PMN or an application for a TME and to publish
periodic status reports on the chemicals under review and the receipt
of notices of commencement to manufacture those chemicals. This status
report, which covers the period from March 23, 2009 through April 10,
2009, consists of the PMNs and TME, both pending or expired, and the
notices of commencement to manufacture a new chemical that the Agency
has received under TSCA section 5 during this time period.
III. Receipt and Status Report for PMNs
This status report identifies the PMNs and TME, both pending or
expired, and the notices of commencement to manufacture a new chemical
that the Agency has received under TSCA section 5 during this time
period. If you are interested in information that is not included in
the following tables, you may contact EPA as described in Unit I. to
access additional non-CBI information that may be available.
Premanufacturer Notices P09-87 thru P09-129 which covered the time
period of December 2, 2008 through December 18, 2008 were inadvertaly
left out of the Federal Register and now are included in this notice.
In Table I of this unit, EPA provides the following information (to
the extent that such information is not claimed as CBI) on the PMNs
received by EPA during this period: the EPA case number assigned to the
PMN; the date the PMN was received by EPA; the projected end date for
EPA's review of the PMN; the submitting manufacturer; the potential
uses identified by the manufacturer in the PMN; and the chemical
identity.
I. 68 Premanufacture Notices Received From: 3/23/09 to 4/10/09
--------------------------------------------------------------------------------------------------------------------------------------------------------
Projected Notice End
Case No. Received Date Date Manufacturer/Importer Use Chemical
--------------------------------------------------------------------------------------------------------------------------------------------------------
P-09-0087 12/02/08 03/01/09 Momentive Performance (G) Catalyst complex (G) Vinyl silicone resin
Materials for release coatings complex
P-09-0088 12/04/08 03/03/09 Momentive Performance (G) Release coating (G) Branched silyl
Materials for polyethylene and hydride cross linker
polypropylene
substrates
P-09-0089 12/04/08 03/03/09 Momentive Performance (G) Chemical (G) Methyl hydrogen
Materials intermediate siloxanes and silicones
chemical intermediate
P-09-0090 12/04/08 03/03/09 Momentive Performance (G) Silsesquioxanes (G) Silsesquioxanes
Materials chemical
intermediate
P-09-0091 12/05/08 03/04/09 CBI (G) Crosslinking (G) Aromatic
agent for coatings polyisocyanate,
aliphatic diol, glycol
ethers-blocked
P-09-0092 12/05/08 03/04/09 CBI (G) Crosslinking (G) Aromatic
agent for coatings polyisocyanate,
aliphatic diol, glycol
ethers-blocked
P-09-0093 12/05/08 03/04/09 CBI (G) Crosslinking (G) Aromatic
agent for coatings polyisocyanate,
aliphatic alcohol,
aliphatic diol, glycol
ethers-blocked
P-09-0094 12/05/08 03/04/09 CBI (G) Crosslinking (G) Aromatic
agent for coatings polyisocyanate,
aliphatic alcohol,
aliphatic diol, glycol
ethers-blocked
P-09-0095 12/05/08 03/04/09 CBI (G) Crosslinking (G) Aromatic
agent for coatings polyisocyanate,
aliphatic diol, glycol
ethers-blocked
P-09-0096 12/05/08 03/04/09 CBI (G) Crosslinking (G) Aromatic
agent for coatings polyisocyanate,
aliphatic diol, glycol
ethers-blocked
P-09-0097 12/05/08 03/04/09 CBI (G) Rheological (S) Amines, C36-
additive, toughener, alkylenedi-, polymers
film former for with pyromellitic
thermoset adhesives dianhydride, maleated
P-09-0098 12/04/08 03/03/09 CBI (G) Polymer additive (S) Zinc, bis[3-(acetyl-
.kappa.O)-6-methyl-2H-
pyran-2,4(3H)-dionato-
.kappa.O4]diaqua-
P-09-0099 12/03/08 03/02/09 CBI (G) Coating component (G) Fluoroethylene vinyl
copolymer
P-09-0100 12/05/08 03/04/09 Sachem, Inc. (G) Chemical (S) Tricyclo [3.3.1.13,7]
intermediate decan-1-aminium, N,N,N-
trimethyl-, chloride
(1:1)
P-09-0101 12/05/08 03/04/09 Sachem, Inc. (G) Chemical (S) Tricyclo [3.3.1.13,7]
intermediate decan-1-aminium, N,N,N-
trimethyl-, hydroxide
(1:1)
P-09-0102 12/09/08 03/08/09 CBI (G) Concrete additive (G) Acrylate polymer with
vinyl ether
P-09-0103 12/09/08 03/08/09 CBI (S) Solder mask for (G) Formaldehyde,
printed circuit polymers with alkyl
board preparation aromatic phenol,
cycloaliphatic-phenol
polymer glycidyl ether,
epichlorohydrin and
aromatic diol, acrylic
cycloaliphatic
carboxylates.
P-09-0104 12/09/08 03/08/09 3M (G) Adhesive (G) Polyurea acrylate
[[Page 23698]]
P-09-0105 12/09/08 03/08/09 Dow Agrosciences (G) Chemical (G) Halo substituted
intermediate benzonitrile
P-09-0106 12/09/08 03/08/09 Meadwestvaco (S) Asphalt (G) Fatty acids, tall-
Corporation -- emulsifier salt oil, reaction products
Specialty Chemicals with modified fatty
Division acids and
polyalkanolamines,
hydrochlorides
P-09-0107 12/09/08 03/08/09 Meadwestvaco (S) Asphalt (G) Fatty acids, tall-
Corporation emulsifier oil, reaction products
with modified fatty
acids and
polyalkanolamines.
P-09-0108 12/10/08 03/09/09 CBI (G) Chemical (G) Dialkyl imidazolium
intermediate halide
P-09-0109 12/10/08 03/09/09 CBI (G) Lubricant (G) Alkyl ammonium
additive tungstate complex
P-09-0110 12/10/08 03/09/09 CBI (G) Lubricant (G) Alkyl ammonium
additive tungstate complex
P-09-0111 12/05/08 03/04/09 PPG Industries, Inc. (G) Component of (G) Alkoxysilane
coating with open functional acrylic resin
use
P-09-0112 12/10/08 03/09/09 CBI (G) Aerspace (G) Bis-A-epoxy resin--
structural adhesive CTBN adduct
P-09-0113 12/11/08 03/10/09 CBI (S) Polymerizable (G) Substituted
component of bisphenolf resin
adhesive
formulations
P-09-0114 12/11/08 03/10/09 Esstech, Inc. (S) Adhesive (S) 1,2,4,5-
benzenetetracarboxylic
acid; 1,4-bis (2-((2-
methyl-1-oxo-2-propenyl)
oxy)-1-(((2-methyl-1-oxo-
2-propenyl) oxy) methyl)
ethyl ester
P-09-0115 12/11/08 03/10/09 CBI (G) Oilfield (G) Alkanedioic acid,
production chemical polymer with N-
(aminoalkyl)-
alkyldiamine,
(chloromethyl)oxirane
and alkylpolyol, acid
salt
P-09-0116 12/09/08 03/08/09 Colonial chemical, (S) Detergent for (S) Coconut oil, reaction
Inc. hard surface products with
cleaners diisopropanolamine
P-09-0117 12/09/08 03/08/09 Colonial Chemical, (S) Detergent for (S) Fats and glyceridic
Inc. hard surface oils, sesame, reaction
cleaners products with
diisopropanolamine
P-09-0118 12/09/08 03/08/09 Colonial Chemical, (S) Detergent for (S) Fats and glyceridic
Inc. hard surface oils, avocado, reaction
cleaners products with
diisopropanolamine
P-09-0119 12/09/08 03/08/09 Colonial Chemical, (S) Detergent for (S) Corn oils, reaction
Inc. hard surface products with
cleaners diisopropanolamine
P-09-0120 12/15/08 03/14/09 CBI (S) Polymerizable (G) Epoxidized siloxane
component of
adhesive
formulations
P-09-0121 12/15/08 03/14/09 CBI (G) Fuel additive (G) Substituted
pyrrolidinealkanaminium,
polyalkylene derivates
P-09-0122 12/16/08 03/15/09 CBI (G) Coating resin for (G) Silicone modified
organic polycarbonate
electrophotographic
photoconductor
P-09-0123 12/16/08 03/15/09 The Dow Chemical (G) Two component (G) Polyester polyol
Company polyurethane
ealstomers (MDI
based)
P-09-0124 12/17/08 03/16/09 Gharda Chemicals (S) Manufacture of (G) Poly (ether ketone)
Limited automotive parts;
manufacture of wire
cable and
insulation;
manufacture of
industrial valve
linigs; manufacture
of heat exchange
parts; oil field
pipe flanges;
aircraft exterior
and interior
aircraft components;
dry transfer
insulation
P-09-0125 12/17/08 03/16/09 Gharda Chemicals (S) Manufacture of (G) polyarylene ether
Limited automotive parts; nitrile
manufacture of wire
and cable
insulation;
manufacture of
industrial valve
linings; manufacture
of heat exchange
parts; oil field
pipe flanges and
gaskets; aircraft -
exterior and
interior components;
dry transfer
insulation
P-09-0126 12/17/08 03/16/09 CBI (S) Intermediate for (G) Substituted
fuel additive pyrrolidine alkylamine,
polyalkylene derivates
[[Page 23699]]
P-09-0127 12/18/08 03/17/09 CBI (G) Open, non- (G) Aliphatic
dispersive use polyurethane resin
(industrial coatings aqueous dispersion
resin)
P-09-0128 12/18/08 03/17/09 Huntsman (S) Exhaust dyeing of (G) Naphthalenedisulfonic
International, LLC cotton acid azo substituted
napthalenesulfonic acid
amino substituted
triazin amino phenyl
alkyl sulfonyl conpound
P-09-0129 12/18/08 03/17/09 CBI (G) Open non- (G) Aqueous polyurethane
dispersive resin dispersion
(adhesive)
P-09-0284 03/25/09 06/22/09 CBI (G) Unsaturated (G) Unsaturated polyester
polyester resin for resin
filled and fiber
reinforced
composites
P-09-0285 03/25/09 06/22/09 CBI (G) Unsaturated (G) Unsaturated polyester
polyester resin for resin
filled and fiber
reinforced
composites
P-09-0286 03/25/09 06/22/09 Cytec Industries Inc. (G) Coatings resin (G) Poly
(oxyalkylenediyl), a-
substituted
carbomonocycle-.omega.-
substituted
carbomonocycle
P-09-0287 03/26/09 06/23/09 CBI (G) Diesel fuel (G) Acrylic acid, alkyl
additive ester, polymer with
ethylene and vinyl
carboxylate
P-09-0288 03/27/09 06/24/09 CBI (G) Silicone additive (G) Alkyl silsesquioxanes
P-09-0289 03/27/09 06/24/09 The Dow Chemical (S) Solid epoxy (G) Solid epoxy resin
Company resins for powder
coatings
P-09-0290 03/27/09 06/24/09 The Dow Chemical (S) Solid epoxy (G) Solid epoxy resin
Company resins for powder
coatings
P-09-0291 03/30/09 06/27/09 CBI (G) Polymerization (G) Ammonium salt of
aid fluoropropanoic acid
P-09-0292 03/31/09 06/28/09 Alberdingk Boley Inc. (S) For wood and (G) Hexanedioic acid,
plastic coatings polymer with 2-
(chloromethyl)oxirane
polymer with 2-ethyl-2-
(hydroxymethyl)-1,3-
propanediol,
hexanedioicacid, 4,4'-(1-
methylethylidene)bis[phe
nol] and oxirane 2-
propenoate, 2,2-dimethyl-
1,3-propanediol, 1,6-
hexanediol, 3-hydroxy-2-
(hydroxymethyl)-2-
methylpropanoic acid and
5-isocyanato-1-
(isocyanatomethyl)-
alkylcyclohexane,
compound with N,N-
diethylethanamine
P-09-0293 03/31/09 06/28/09 CBI (G) Coating for open, (G) Phosphoric acid,
non-dispersive use; mixed esters with
surface active agent partially fluorinated
alcohol, ammonium salts
P-09-0294 03/31/09 06/28/09 CBI (G) Coating for open, (G) Phosphoric acid,
non-dispersive use; mixed esters with
surface active agent partially fluorinated
alcohol, ammonium salts
P-09-0295 03/30/09 06/27/09 CBI (G) (G) Copolymer of the
Dispersant\wetting esters of acrylic acid
agent and methacrylic acid
P-09-0296 03/30/09 06/27/09 CBI (G) (G) Acrylic acid esters
Dispersant\wetting and methacrylic acid
agent esters copolymer,
cmpound with
aminoethylpropanol
P-09-0297 03/30/09 06/27/09 CBI (G) (G) Copolymer of acrylic
Dispersant\wetting acid and methacrylic
agent acid esters, and
vinylcaprolactam
P-09-0298 03/30/09 06/27/09 CBI (G) (G) Copolymer of acrylic
Dispersant\wetting acid and methacrylic
agent acid esters, and
vinylcaprolactam,
compound with
aminomethylpropanol
P-09-0299 04/02/09 06/30/09 CBI (G) Dispersant for (G) Fatty acid amide
organic pigments in
polyolefin
thermoplastics
P-09-0300 04/03/09 07/01/09 CBI (G) Diesel fuel (G) Aromatic dicarboxylic
additive acid dialkyl amide
dialkyl ammonium salt
P-09-0301 04/03/09 07/01/09 CBI (G) Adhesive (G) Adipic acid, polymer
component with carbomonocyclic
diisocyanates,
benzenepolycarboxylic
acids and alkanediols
P-09-0302 04/03/09 07/01/09 CBI (G) Raw material (G) Adipic acid, polymer
with
benzenepolycarboxylic
acids and alkanepolyols
[[Page 23700]]
P-09-0303 04/03/09 07/01/09 CBI (G) Raw material (G) Adipic acid, polymer
with
benzenepolycarboxylic
acids and alkanediols
P-09-0304 04/07/09 07/05/09 CBI (G) Binding aid (G) Propanamine blocked
polymeric isocyanate
P-09-0305 04/07/09 07/05/09 CBI (G) Adhesive and (G) Polymeric isocyanate
sealant
P-09-0306 04/06/09 07/04/09 CBI (G) Dispersant (G) Polyester
P-09-0307 04/10/09 07/08/09 CBI (S) Raw material used (G) Amine acrylate co-
in ultra violet initiator
curable inks and
coatings
P-09-0308 04/10/09 07/08/09 CBI (S) Raw material used (G) Amine modified
in ultra violet polyester acrylate
curable inks and
coatings
--------------------------------------------------------------------------------------------------------------------------------------------------------
In Table II of this unit, EPA provides the following information
(to the extent that such information is not claimed as CBI) on the TMEs
received:
II. 1 Test Marketing Exemption Notices Received From: 3/23/09 to 4/10/09
--------------------------------------------------------------------------------------------------------------------------------------------------------
Projected Notice End
Case No. Received Date Date Manufacturer/Importer Use Chemical
--------------------------------------------------------------------------------------------------------------------------------------------------------
T-09-0008 03/25/09 05/08/09 Cytec Industries Inc. (G) Coatings resin (G)
Poly(oxyalkylenediyl
), a-substituted
carbomonocycle-
.omega.-substituted
carbomonocycle
--------------------------------------------------------------------------------------------------------------------------------------------------------
In Table III of this unit, EPA provides the following information
(to the extent that such information is not claimed as CBI) on the
Notices of Commencement to manufacture received:
III. 38 Notices of Commencement From: 3/23/09 to 4/10/09
----------------------------------------------------------------------------------------------------------------
Commencement Notice
Case No. Received Date End Date Chemical
----------------------------------------------------------------------------------------------------------------
P-02-0112 03/25/09 10/19/04 (G) Amidosiloxane
P-04-0514 04/03/09 03/18/09 (G) Polybutadiene acrylate
P-06-0103 04/08/09 03/19/09 (G) Polyetherpolyol
polymer with aromatic
ketone
P-07-0071 03/20/09 03/01/09 (G) Mdi and polymeric MDI
prepolymer
P-07-0587 04/01/09 03/17/09 (G) N,N-dialkylalkylamine
P-08-0340 04/03/09 03/06/09 (G) 1,2-ethanediamine,
N1,N2-bis(2-aminoethyl),
polymer with
haloalkyloxirane and
polyoxyalkane
P-08-0477 04/03/09 03/18/09 (G) Hexyl carbamate
P-08-0560 04/01/09 03/18/09 (G) Modified
polyalkyldiene polymer
P-08-0642 04/06/09 03/31/09 (G) Fluorinated acrylic
copolymer
P-08-0705 03/27/09 03/09/09 (S) Chromium, 1-[2-[5-(1,1-
dimethylpropyl)-2-hydroxy-
3-nitrophenyl]diazenyl]-2-
naphthalenol 1-[2-[2-
hydroxy-4(or 5)-
nitrophenyl]diazenyl]-2-
naphthalenol ammonium
sodium complexes
P-08-0719 04/03/09 03/18/09 (G) Polyester polyol
P-08-0742 03/24/09 03/04/09 (S) Phosphonium,
tetrabutyl-, hydroxide
(1:1)
P-09-0005 03/24/09 03/14/09 (G) Substituted phenol,
polymer with 2-
(chloromethyl)oxirane 1,3-
diisocyanatomethylbenzene
, 2-ethylhexanoate
(ester), cyclized,
reaction products with
diethylenetriamine and 2-
(methylamino) ethanol
P-09-0010 04/02/09 03/05/09 (G) Polyurethane pre-
polymers of polymeric MDI
and polyether polyols
P-09-0049 04/06/09 03/26/09 (G) Acrylic copolymer
P-09-0069 03/25/09 03/19/09 (G) Amides, from lignin,
tall oil fatty acids, C21
dicarboxylic acids and
polyalkanolamines
P-09-0070 03/25/09 03/19/09 (G) Amides, from lignin,
tall oil fatty acids, C21
dicarboxylic acids and
polyalkanolamines,
hydrochlorides
P-09-0081 03/24/09 02/27/09 (G) Polymer of aliphatic
diols, aliphatic polyols,
and carboxylic anhydrides
P-09-0086 03/26/09 03/16/09 (S) Cyclosiloxanes, me 3-
(2-oxiranylmethoxy)propyl
P-09-0092 03/25/09 03/18/09 (G) Aromatic
polyisocyanate, aliphatic
diol, glycol ethers-
blocked
P-09-0121 04/08/09 04/02/09 (G) Substituted
pyrrolidinealkanaminium,
polyalkylene derivates
[[Page 23701]]
P-09-0126 04/06/09 03/25/09 (G) Substituted
pyrrolidine alkylamine,
polyalkylene derivates
P-94-2242 04/02/09 06/01/95 (G) Salt of aminotetrazole
P-08-0070 12/15/08 11/25/08 (G) Fluorosilicone
P-08-0229 12/08/08 11/18/08 (G) Polyether and
trialkylsilylalkylamine
modified polyurethane
P-08-0230 12/08/08 11/18/08 (G) Trialkoxysilylalkylene
modified
polydialkylsiloxane
P-08-0399 12/17/08 11/24/08 (S) 1-(2,3-dimethyl-
bicyclo[2.2.1]heptan)-
ethanone
P-08-0409 12/03/08 11/05/08 (G) Alpha-alkenes, C20 24
.alpha.-,polymers with
maleic anhydride, C16 30-
alkyl esters
P-08-0421 12/03/08 11/28/08 (G) Acrylic resin
P-08-0430 12/04/08 11/12/08 (G) Isocyanate terminated
urethane polymer
P-08-0465 12/16/08 12/12/08 (G) Reaction product of
substituted dioxazine
compound and substituted
alkyl sulfonyl compound
P-08-0466 12/10/08 11/28/08 (G) Phenolic resin
P-08-0629 12/02/08 11/13/08 (G) Phenol, 2,4,6,-
tris[(dimethylamino)methy
l]-, reaction products
with triethylenetetramine
mixture (includes: N,N'-
bis(2-aminoethyl)-1,2-
ethanediamine, tris-(2-
aminoethyl)amine), N,N'-
bis-(2-
aminoethyl)piperazine,
and N-[(2-aminoethyl)2-
aminoethyl]piperazine
P-08-0648 12/01/08 11/17/08 (G) Pentaisobutylene
P-08-0650 12/12/08 12/11/08 (G) Styrene, methanamine
modified polymer
P-08-0651 12/12/08 12/11/08 (G) Halogenated styrene
modified polymer
P-08-0652 12/12/08 12/11/08 (G) Acrylic styrene
modified polymer
P-08-0653 12/12/08 12/11/08 (G) Acrylonitrile,
acrylate, styrene
modified polymer
----------------------------------------------------------------------------------------------------------------
List of Subjects
Environmental protection, Chemicals, Premanufacturer notices.
Dated: April 22, 2009.
Chandler Sirmons,
Acting Director, Information Management Division, Office of Pollution
Prevention and Toxics.
[FR Doc. E9-11748 Filed 5-19-09; 8:45 am]
BILLING CODE 6560-50-S