[Federal Register: June 16, 2009 (Volume 74, Number 114)]
[Rules and Regulations]
[Page 28439-28441]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr16jn09-1]
========================================================================
Rules and Regulations
Federal Register
________________________________________________________________________
This section of the FEDERAL REGISTER contains regulatory documents
having general applicability and legal effect, most of which are keyed
to and codified in the Code of Federal Regulations, which is published
under 50 titles pursuant to 44 U.S.C. 1510.
The Code of Federal Regulations is sold by the Superintendent of Documents.
Prices of new books are listed in the first FEDERAL REGISTER issue of each
week.
========================================================================
[[Page 28439]]
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2009-0518; Directorate Identifier 2009-SW-22-AD;
Amendment 39-15940; AD 2009-13-01]
RIN 2120-AA64
Airworthiness Directives; Sikorsky Aircraft Corporation Model S-
92A Helicopters
AGENCY: Federal Aviation Administration, DOT.
ACTION: Final rule; request for comments.
-----------------------------------------------------------------------
SUMMARY: This amendment supersedes an existing airworthiness directive
(AD) for Sikorsky Aircraft Corporation (Sikorsky) Model S-92A
helicopters. That AD currently requires removing all main gearbox (MGB)
filter bowl assembly mounting titanium studs (titanium studs) and
replacing them with steel studs. This amendment requires the same
actions as the existing AD as well as changes to the Rotorcraft Flight
Manual (RFM). This amendment is prompted by an accident, by recent RFM
changes made by the manufacturer that were not available when we issued
the existing AD, and by our determination that certain MGB Normal and
Emergency procedures in the RFM are unclear, may cause confusion, and
may mislead the crew regarding MGB malfunctions, in particular the
urgency to land immediately after warning indications of loss of MGB
oil pressure and oil pressure below 5 pounds per square inch (psi).
Replacing the titanium studs is intended to prevent their failure,
which could result in rapid loss of oil, failure of the MGB, and
subsequent loss of control of the helicopter. Changing the RFM
procedures is intended to clarify and emphasize certain Normal and
Emergency procedures to give the crew the best available information in
the event of certain MGB malfunctions.
DATES: Effective July 1, 2009.
The incorporation by reference of Sikorsky Alert Service Bulletin
No. 92-63-014, Revision A, dated March 20, 2009, was approved
previously for incorporation by reference by the Director of the
Federal Register on April 27, 2009 (74 FR 18977, April 27, 2009).
Comments for inclusion in the Rules Docket must be received on or
before August 17, 2009.
ADDRESSES: Use one of the following addresses to submit comments on
this AD:
Federal eRulemaking Portal: Go to http://
www.regulations.gov. Follow the instructions for submitting comments.
Fax: 202-493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue, SE., Washington, DC 20590.
Hand Delivery: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue, SE., Washington, DC 20590, between 9 a.m. and 5 p.m.,
Monday through Friday, except Federal holidays.
You may get the service information identified in this AD from
Sikorsky Aircraft Corporation, Attn: Manager, Commercial Technical
Support, mailstop s581a, 6900 Main Street, Stratford, CT, telephone
(203) 383-4866, e-mail address tsslibrary@sikorsky.com, or at http://
www.sikorsky.com.
Examining the Docket: You may examine the docket that contains the
AD, any comments, and other information on the Internet at http://
www.regulations.gov, or in person at the Docket Operations office
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The Docket Operations office (telephone (800) 647-5527) is
located in Room W12-140 on the ground floor of the West Building at the
street address stated in the ADDRESSES section. Comments will be
available in the AD docket shortly after receipt.
FOR FURTHER INFORMATION CONTACT: John M. Coffey, Flight Test Engineer,
FAA, 12 New England Executive Park, Burlington, MA 01803, telephone
(781) 238-7173, fax (781) 238-7170.
SUPPLEMENTARY INFORMATION: On March 23, 2009, we issued Emergency AD
2009-07-53 for Sikorsky Model S-92A helicopters, which requires, before
further flight, removing all titanium studs that attach the MGB filter
bowl assembly to the MGB and replacing them with steel studs. That
action was prompted by the failure of 2 studs that were found broken
during a fatal accident investigation in Canada. Before the accident,
the manufacturer was investigating a July 2008 incident that also
involved broken studs. In both cases, the broken studs resulted in
rapid loss of MGB oil. The failures have been tied to fretting and
galling of the original titanium studs. That emergency AD was published
as Amendment 39-15886 on April 27, 2009 (74 FR 18977). This AD
continues to require removing all titanium studs and replacing them
with steel studs.
Since the fatal accident and since issuing AD 2009-07-53, Sikorsky
has issued revisions to the Normal and Emergency procedures of the RFM.
We have determined that these revisions are necessary because the
existing procedures are unclear, may cause confusion, and may mislead
the crew regarding MGB malfunctions, in particular the urgency to land
immediately after warning indications of loss of MGB oil pressure and
oil pressure below 5 psi. This action does not mandate the procedures
the pilot must perform in an emergency, but requires making changes to
the RFM to clarify and emphasize the Normal and Emergency procedures
addressing specified MGB malfunctions, thus giving the pilot the
necessary information to make an informed decision. We are superseding
the existing AD to include the most recent RFM revisions because the
revisions were not available when we originally issued AD 2009-07-53.
We have reviewed Sikorsky Alert Service Bulletin No. 92-63-014A,
Revision A, dated March 20, 2009 (ASB), which describes procedures for
removing titanium studs and replacing them with steel suds. We have
also reviewed the RFM revisions and, after full coordination with
Sikorsky, approved them on May 13, 2009. Sikorsky has since assured us
that they have provided the revised RFM procedures to all affected
operators. The RFM revisions are as follows:
[[Page 28440]]
SA S92A-RFM-000 Revision No. 4,
SA S92A-RFM-002 Revision No. 10,
SA S92A-RFM-003 Revision No. 10,
SA S92A-RFM-004 Revision No. 8,
SA S92A-RFM-005 Revision No. 7,
SA S92A-RFM-006 Revision No. 8, and
S92A-RFM Supplement No. 3, Revision No. 2.
In addition to the RFM revisions, we have also reviewed associated
Errata Sheets, dated June 4, 2009, that provide corrections to those
RFM revisions; however, we are not mandating that they be incorporated.
Since an unsafe condition has been identified that is likely to
exist or develop on other Sikorsky Model S-92A helicopters of the same
type design, this AD supersedes AD 2009-07-53 to require, before
further flight, removing all titanium studs and replacing them with
steel studs. These actions must be accomplished by following the
specified portions of the ASB described previously. Because the
critical unsafe condition can adversely affect the structural integrity
and controllability of the helicopter, AD 2009-07-53 remains in full
effect until the effective date of this AD.
Making the Normal and Emergency RFM revisions that were not
available when we issued AD 2009-07-53 is required within 10 hours
time-in-service. The short compliance time is required because certain
procedures in the existing RFM may be misleading, presenting an
unacceptable level of risk, and because the required RFM revisions are
already approved by the FAA and available to operators, imposing a
minimal burden. Therefore, it is found that notice and opportunity for
prior public comment hereon are unnecessary and contrary to the public
interest, and that good cause also exists for making this amendment
effective in less than 30 days.
We estimate that this AD will affect 35 helicopters of U.S.
registry. Replacing the studs will take approximately 6 work hours per
helicopter to accomplish at an average labor rate of $80 per work hour.
In accordance with the ASB, required parts and tooling are available at
no cost. Making the changes to the RFM will take a minimal amount of
time and cost. Based on these figures, we estimate the total cost
impact of the AD on U.S. operators to be $16,800, assuming there are no
parts and tooling costs.
Comments Invited
This AD is a final rule that involves requirements that affect
flight safety and was not preceded by notice and an opportunity for
public comment; however, we invite you to submit any written data,
views, or arguments regarding this AD. Send your comments to an address
listed under ADDRESSES. Include ``Docket No. FAA-2009-0518; Directorate
Identifier 2009-SW-22-AD'' at the beginning of your comments. We
specifically invite comments on the overall regulatory, economic,
environmental, and energy aspects of the AD. We will consider all
comments received by the closing date and may amend the AD in light of
those comments.
We will post all comments we receive, without change, to http://
www.regulations.gov, including any personal information you provide. We
will also post a report summarizing each substantive verbal contact
with FAA personnel concerning this AD. Using the search function of our
docket Web site, you can find and read the comments to any of our
dockets, including the name of the individual who sent the comment. You
may review the DOT's complete Privacy Act Statement in the Federal
Register published on April 11, 2000 (65 FR 19477-78).
Regulatory Findings
We have determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national Government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that the regulation:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared an economic evaluation of the estimated costs to comply
with this AD. See the AD docket to examine the economic evaluation.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
0
Accordingly, pursuant to the authority delegated to me by the
Administrator, the Federal Aviation Administration amends part 39 of
the Federal Aviation Regulations (14 CFR part 39) as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. Section 39.13 is amended by removing Amendment 39-15886 (74 FR
18977, April 27, 2009), and by adding a new airworthiness directive
(AD), Amendment 39-15940, to read as follows:
2009-13-01 Sikorsky Aircraft Corporation: Amendment 39-15940. Docket
No. FAA-2009-0518; Directorate Identifier 2009-SW-22-AD. Supersedes
AD 2009-07-53, Amendment 39-15886, Docket No. FAA-2009-0351,
Directorate Identifier 2009-SW-08-AD.
Applicability: Model S-92A helicopters, certificated in any
category.
Compliance: Required as indicated, unless accomplished
previously.
To prevent failure of a main gearbox (MGB) filter bowl assembly
mounting titanium stud (titanium stud), which could result in rapid
loss of oil, failure of the MGB, and subsequent loss of control of
the helicopter; and to clarify and emphasize certain Normal and
Emergency procedures to give the crew the best available information
in the event of certain MGB malfunctions, accomplish the following:
(a) Before further flight, for all Model S-92A helicopters with
a MGB housing assembly, part number (P/N) 92351-15110-042, -043, or
-044, that is not marked with ``TS-062-01'' near the P/N:
(1) Remove the titanium studs by following the Accomplishment
Instructions in Sikorsky Alert Service Bulletin No. 92-63-014, Rev.
[[Page 28441]]
A, dated March 20, 2009 (ASB), paragraph 3.A.
Note 1: Figure 1 of the ASB contains guidance for removal and
installation of the studs
.(2) Visually inspect the tapped holes and the MGB housing
lockring counterbore for damage. If you find damage in the tapped
holes or in the MGB housing lockring counterbore, contact the Boston
Aircraft Certification Office for an approved repair.
(3) Install steel studs and mark the MGB housing as ``TS-062-
01'' near the P/N by following the Accomplishment Instructions in
the ASB, paragraph 3.C.
(b) Within 10 hours time-in-service, for all helicopters
regardless of MGB housing assembly P/N:
(1) Revise the Normal and Emergency procedures sections of the
Rotorcraft Flight Manual (RFM) by making the following changes,
approved May 13, 2009:
----------------------------------------------------------------------------------------------------------------
RFM Remove Remove Insert
----------------------------------------------------------------------------------------------------------------
SA S92A-RFM-000 Part I............. Temporary Revision (T- Page 2-12, and Sub- Page 2-12, and Sub-Section
Rev) No. 1, Revised Section 7 ``Gear Box 7 ``Gear Box
Main Gearbox Malfunctions'' from Malfunctions'' from
Emergency Procedure. Section III. Section III of SA S92A-RFM-
000, Revision No. 4.
SA S92A-RFM-002 Part I............. T-Rev No. 5, Revised Page 2-13, and Sub- Page 2-13, and Sub-Section
Main Gearbox Section 7 ``Gear Box 7 ``Gear Box
Emergency Procedure. Malfunctions'' from Malfunctions'' from
Section III. Section III of SA S92A-RFM-
002, Revision No. 10.
SA S92A-RFM-003 Part I............. T-Rev No. 4, Revised Page 2-13, and Sub- Page 2-13, and Sub-Section
Main Gearbox Section 7 ``Gear Box 7 ``Gear Box
Emergency Procedure. Malfunctions'' from Malfunctions'' from
Section III. Section III of SA S92A-RFM-
003, Revision No. 10.
SA S92A-RFM-004 Part I............. T-Rev No. 4, Revised Page 2-12, and Sub- Page 2-12, and Sub-Section
Main Gearbox Section 7 ``Gear Box 7 ``Gear Box
Emergency Procedure. Malfunctions'' from Malfunctions'' from
Section III. Section III of SA S92A-RFM-
004, Revision No. 8.
SA S92A-RFM-005 Part I............. T-Rev No. 3, Revised Page 2-13, and Sub- Page 2-13, and Sub-Section
Main Gearbox Section 7 ``Gear Box 7 ``Gear Box
Emergency Procedure. Malfunctions'' from Malfunctions'' from
Section III. Section III of SA S92A-RFM-
005, Revision No. 7.
SA S92A-RFM-006 Part I............. T-Rev No. 2, Revised Page 2-13, and Sub- Page 2-13, and Sub-Section
Main Gearbox Section 7 ``Gear Box 7 ``Gear Box
Emergency Procedure. Malfunctions'' from Malfunctions'' from
Section III. Section III of SA S92A-RFM-
006, Revision No. 8.
S92A-RFMS No. 3.................... N/A................... Sub-Section 7 ``Gear Sub-Section 7 ``Gear Box
Box Malfunctions'' Malfunctions'' from
from Section III. Section III of
S92A[dash]RFM Supplement
No. 3, Revision No. 2.
----------------------------------------------------------------------------------------------------------------
All paragraphs of subsection 7 ``Gear Box Malfunctions'' starting with paragraph 7.0 are affected.
----------------------------------------------------------------------------------------------------------------
Note 2: Inserting the following revisions, approved on May 13,
2009, and their associated Errata Sheets, dated June 4, 2009, into
the RFM, as applicable, satisfies the requirements of this AD:
(i) SA S92A-RFM-000 Revision No. 4,
(ii) SA S92A-RFM-002 Revision No. 10,
(iii) SA S92A-RFM-003 Revision No. 10,
(iv) SA S92A-RFM-004 Revision No. 8,
(v) SA S92A-RFM-005 Revision No. 7,
(vi) SA S92A-RFM-006 Revision No. 8, and
(vii) S92A-RFM Supplement No. 3, Revision No. 2.
(c) To request a different method of compliance or a different
compliance time for this AD, follow the procedures in 14 CFR 39.19.
Contact the Manager, Boston Aircraft Certification Office, FAA,
Attn: John M. Coffey, FAA, 12 New England Executive Park,
Burlington, MA 01803, telephone (781) 238-7173, fax (781) 238-7170,
for information about previously approved alternative methods of
compliance.
(d) Special flight permits will not be issued.
(e) Remove and replace the titanium studs by following the
specified portions of Sikorsky Alert Service Bulletin No. 92-63-014,
Revision A, dated March 20, 2009. The Director of the Federal
Register previously approved the incorporation by reference of this
information on April 27, 2009 under 5 U.S.C. 552(a) and 1 CFR part
51 (74 FR 18977, April 27, 2009. Copies may be obtained from
Sikorsky Aircraft Corporation, Attn: Manager, Commercial Technical
Support, mailstop s581a, 6900 Main Street, Stratford, CT, telephone
(203) 383-4866, e-mail address tsslibrary@sikorsky.com or at http://
www.sikorsky.com. Copies may be inspected at the FAA, Office of the
Regional Counsel, Southwest Region, 2601 Meacham Blvd., Room 663,
Fort Worth, Texas, or at the National Archives and Records
Administration (NARA). For information on the availability of this
material at NARA, call 202-741-6030, or go to: http://
www.archives.gov/federal_register/code_of_federal_regulations/
ibr_locations.html.
(f) This amendment becomes effective on July 1, 2009.
Issued in Fort Worth, Texas, on June 9, 2009.
Mark R. Schilling,
Acting Manager, Rotorcraft Directorate, Aircraft Certification Service.
[FR Doc. E9-14081 Filed 6-15-09; 8:45 am]
BILLING CODE 4910-13-P