[Federal Register: April 6, 2009 (Volume 74, Number 64)]
[Proposed Rules]
[Page 15399-15401]
From the Federal Register Online via GPO Access [wais.access.gpo.gov]
[DOCID:fr06ap09-14]
========================================================================
Proposed Rules
Federal Register
________________________________________________________________________
This section of the FEDERAL REGISTER contains notices to the public of
the proposed issuance of rules and regulations. The purpose of these
notices is to give interested persons an opportunity to participate in
the rule making prior to the adoption of the final rules.
========================================================================
[[Page 15399]]
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2009-0310; Directorate Identifier 2009-NM-012-AD]
RIN 2120-AA64
Airworthiness Directives; Bombardier Model CL-600-2B19 (Regional
Jet Series 100 & 440) Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Notice of proposed rulemaking (NPRM).
-----------------------------------------------------------------------
SUMMARY: We propose to adopt a new airworthiness directive (AD) for the
products listed above. This proposed AD results from mandatory
continuing airworthiness information (MCAI) originated by an aviation
authority of another country to identify and correct an unsafe
condition on an aviation product. The MCAI describes the unsafe
condition as:
During the Acceptance Test Procedure (ATP) of returned Inboard
Flap Actuators * * * an excessive wear condition was identified
regarding endplay between the flap actuator and ball screw.
Excessive wear of the screw and ball nut could potentially lead to a
flap system jam. * * *
* * * * *
The proposed AD would require actions that are intended to address the
unsafe condition described in the MCAI.
DATES: We must receive comments on this proposed AD by May 6, 2009.
ADDRESSES: You may send comments by any of the following methods:
Federal eRulemaking Portal: Go to http://
www.regulations.gov. Follow the instructions for submitting comments.
Fax: (202) 493-2251.
Mail: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New
Jersey Avenue, SE., Washington, DC 20590.
Hand Delivery: U.S. Department of Transportation, Docket
Operations, M-30, West Building Ground Floor, Room W12-40, 1200 New
Jersey Avenue, SE., Washington, DC, between 9 a.m. and 5 p.m., Monday
through Friday, except Federal holidays.
For service information identified in this proposed AD, contact
Bombardier, Inc., 400 C[ocirc]te-Vertu Road West, Dorval, Qu[eacute]bec
H4S 1Y9, Canada; telephone 514-855-5000; fax 514-855-7401; e-mail
thd.crj@aero.bombardier.com; Internet http://www.bombardier.com. You
may review copies of the referenced service information at the FAA,
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton,
Washington. For information on the availability of this material at the
FAA, call 425-227-1221 or 425-227-1152.
Examining the AD Docket
You may examine the AD docket on the Internet at http://
www.regulations.gov; or in person at the Docket Operations office
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this proposed AD, the regulatory
evaluation, any comments received, and other information. The street
address for the Docket Operations office (telephone (800) 647-5527) is
in the ADDRESSES section. Comments will be available in the AD docket
shortly after receipt.
FOR FURTHER INFORMATION CONTACT: Fabio Buttitta, Aerospace Engineer,
Airframe and Propulsion Branch, ANE-171, FAA, New York Aircraft
Certification Office, 1600 Stewart Avenue, Suite 410, Westbury, New
York 11590; telephone (516) 228-7303; fax (516) 794-5531.
SUPPLEMENTARY INFORMATION:
Comments Invited
We invite you to send any written relevant data, views, or
arguments about this proposed AD. Send your comments to an address
listed under the ADDRESSES section. Include ``Docket No. FAA-2009-0310;
Directorate Identifier 2009-NM-012-AD'' at the beginning of your
comments. We specifically invite comments on the overall regulatory,
economic, environmental, and energy aspects of this proposed AD. We
will consider all comments received by the closing date and may amend
this proposed AD based on those comments.
We will post all comments we receive, without change, to http://
www.regulations.gov, including any personal information you provide. We
will also post a report summarizing each substantive verbal contact we
receive about this proposed AD.
Discussion
Transport Canada Civil Aviation (TCCA), which is the aviation
authority for Canada, has issued Canadian Airworthiness Directive CF-
2008-33R1, dated January 9, 2009 (referred to after this as ``the
MCAI''), to correct an unsafe condition for the specified products. The
MCAI states:
During the Acceptance Test Procedure (ATP) of returned Inboard
Flap Actuators Part Number (PN) 601R93101-19, an excessive wear
condition was identified regarding endplay between the flap actuator
and ball screw. Excessive wear of the screw and ball nut could
potentially lead to a flap system jam. A Temporary Revision (TR) has
been made to the Bombardier CL-600-2B19 Maintenance Requirements
Manual (MRM), Appendix A, ``Certification Maintenance Requirements''
(CMR) to ensure that unacceptable wear on the nut and ball screw is
detected and corrected.
Revision 1 of this directive introduces a new phase-in schedule
for performing a new CMR task C27-50-300-01.
Relevant Service Information
Bombardier has issued Temporary Revision 2A-41, dated November 7,
2007, to Appendix A of the Airworthiness Requirements, Part 2, of the
Bombardier CL-600-2B19 Maintenance Requirements Manual. The actions
described in this service information are intended to correct the
unsafe condition identified in the MCAI.
FAA's Determination and Requirements of This Proposed AD
This product has been approved by the aviation authority of another
country, and is approved for operation in the United States. Pursuant
to our bilateral agreement with the State of Design Authority, we have
been notified of the unsafe condition described in the MCAI and service
information referenced above. We are proposing this AD because we
evaluated all pertinent information and determined an unsafe condition
exists and is likely to exist or develop on other products of the same
type design.
[[Page 15400]]
Differences Between This AD and the MCAI or Service Information
We have reviewed the MCAI and related service information and, in
general, agree with their substance. But we might have found it
necessary to use different words from those in the MCAI to ensure the
AD is clear for U.S. operators and is enforceable. In making these
changes, we do not intend to differ substantively from the information
provided in the MCAI and related service information.
We might also have proposed different actions in this AD from those
in the MCAI in order to follow FAA policies. Any such differences are
highlighted in a NOTE within the proposed AD.
Costs of Compliance
Based on the service information, we estimate that this proposed AD
would affect 668 products of U.S. registry. We also estimate that it
would take about 3 work-hours per product to comply with the basic
requirements of this proposed AD. The average labor rate is $80 per
work-hour. Based on these figures, we estimate the cost of the proposed
AD on U.S. operators to be $160,320, or $240 per product.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's
authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, Part A, Subpart III, Section 44701: General
Requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We determined that this proposed AD would not have federalism
implications under Executive Order 13132. This proposed AD would not
have a substantial direct effect on the States, on the relationship
between the national Government and the States, or on the distribution
of power and responsibilities among the various levels of government.
For the reasons discussed above, I certify this proposed
regulation:
1. Is not a ``significant regulatory action'' under Executive Order
12866;
2. Is not a ``significant rule'' under the DOT Regulatory Policies
and Procedures (44 FR 11034, February 26, 1979); and
3. Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this proposed AD and placed it in the AD docket.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
The Proposed Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA proposes to amend 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
2. The FAA amends Sec. 39.13 by adding the following new AD:
Bombardier, Inc. (Formerly Canadair): Docket No. FAA-2009-0310;
Directorate Identifier 2009-NM-012-AD.
Comments Due Date
(a) We must receive comments by May 6, 2009.
Affected ADs
(b) None.
Applicability
(c) This AD applies to Bombardier Model CL-600-2B19 (Regional
Jet Series 100 & 440) airplanes, all serial numbers, certificated in
any category.
Note 1: This AD requires revisions to certain operator
maintenance documents to include new inspections. Compliance with
these inspections is required by 14 CFR 91.403(c). For airplanes
that have been previously modified, altered, or repaired in the
areas addressed by these inspections, the operator may not be able
to accomplish the inspections described in the revisions. In this
situation, to comply with 14 CFR 91.403(c), the operator must
request approval for an alternative method of compliance according
to paragraph (g)(1) of this AD. The request should include a
description of changes to the required inspections that will ensure
the continued operational safety of the airplane.
Subject
(d) Air Transport Association (ATA) of America Code 27: Flight
Controls.
Reason
(e) The mandatory continuing airworthiness information (MCAI)
states:
During the Acceptance Test Procedure (ATP) of returned Inboard
Flap Actuators Part Number (PN) 601R93101-19, an excessive wear
condition was identified regarding endplay between the flap actuator
and ball screw. Excessive wear of the screw and ball nut could
potentially lead to a flap system jam. A Temporary Revision (TR) has
been made to the Bombardier CL-600-2B19 Maintenance Requirements
Manual (MRM), Appendix A, ``Certification Maintenance Requirements''
(CMR) to ensure that unacceptable wear on the nut and ball screw is
detected and corrected.
Revision 1 of this directive introduces a new phase-in schedule
for performing a new CMR task C27-50-300-01.
Actions and Compliance
(f) Unless already done, within 30 days after the effective date
of this AD, revise the Airworthiness Requirements section of
Bombardier Model CL-600-2B19 MRM to include the information in
Bombardier TR 2A-41, dated November 7, 2007, to Appendix A of the
Airworthiness Requirements, Part 2, of the Bombardier CL-600-2B19
Maintenance Requirements Manual (MRM). The initial compliance time
with the new CMR task must be done within 500 flight hours after the
effective date of this AD.
Note 2: The actions required by paragraph (f) of this AD may be
done by inserting a copy of Bombardier TR 2A-41, dated November 7,
2007, to Appendix A of the Airworthiness Requirements, Part 2, of
the Bombardier CL-600-2B19 MRM. When this TR has been included in
general revisions of the MRM, the general revisions may be inserted
in the MRM, provided the relevant information in the general
revision is identical to that in Bombardier TR 2A-41.
FAA AD Differences
Note 3: This AD differs from the MCAI and/or service information
as follows: No differences.
Other FAA AD Provisions
(g) The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager, New
York Aircraft Certification Office (ACO), FAA, has the authority to
approve AMOCs for this AD, if requested using the procedures found
in 14 CFR 39.19. Send information to ATTN: Fabio Buttitta, Aerospace
Engineer, Airframe and Propulsion Branch, ANE-171, FAA, New York
ACO, 1600 Stewart Avenue, Suite 410, Westbury, New York 11590;
telephone (516) 228-7303; fax (516) 794-5531. Before using any
approved AMOC on any airplane to which the AMOC applies, notify your
principal maintenance inspector (PMI) or principal avionics
inspector (PAI), as appropriate, or lacking a principal inspector,
your local Flight Standards District Office.
[[Page 15401]]
(2) Airworthy Product: For any requirement in this AD to obtain
corrective actions from a manufacturer or other source, use these
actions if they are FAA-approved. Corrective actions are considered
FAA-approved if they are approved by the State of Design Authority
(or their delegated agent). You are required to assure the product
is airworthy before it is returned to service.
(3) Reporting Requirements: For any reporting requirement in
this AD, under the provisions of the Paperwork Reduction Act, the
Office of Management and Budget (OMB) has approved the information
collection requirements and has assigned OMB Control Number 2120-
0056.
Related Information
(h) Refer to MCAI Canadian Airworthiness Directive CF-2008-33R1,
dated January 9, 2009; and Bombardier Temporary Revision 2A-41,
dated November 7, 2007, to Appendix A of the Airworthiness
Requirements, Part 2, of the Bombardier CL-600-2B19 Maintenance
Requirements Manual; for related information.
Issued in Renton, Washington, on March 30, 2009.
Stephen P. Boyd,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. E9-7643 Filed 4-3-09; 8:45 am]
BILLING CODE 4910-13-P