[Federal Register Volume 75, Number 94 (Monday, May 17, 2010)]
[Rules and Regulations]
[Pages 27424-27427]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2010-10875]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2009-1066; Directorate Identifier 2009-NM-028-AD;
Amendment 39-16284; AD 2010-10-05]
RIN 2120-AA64
Airworthiness Directives; The Boeing Company Model 747-100, 747-
100B, 747-100B SUD, 747-200B, 747-300, 747SR, and 747SP Series
Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: The FAA is superseding an existing airworthiness directive
(AD), which applies to certain Model 747 airplanes. That AD currently
requires repetitive inspections to detect cracking in certain fuselage
skin lap joints, and repair if necessary. This new AD expands the
inspection area in the existing AD, adds a modification of certain lap
joints, and adds certain post-repair inspections of the lap joints.
Accomplishing the modification ends the repetitive inspections required
by the existing AD for the length of lap joint that is modified. This
AD results from a structural review of affected skin lap joints for
widespread fatigue damage. We are issuing this AD to prevent fatigue
cracking in certain lap joints, which could result in rapid
depressurization of the airplane.
DATES: This AD becomes effective June 21, 2010.
The Director of the Federal Register approved the incorporation by
reference of certain publications listed in the AD as of June 21, 2010.
On July 13, 1994 (59 FR 30277, June 13, 1994), the Director of the
Federal Register approved the incorporation by reference of certain
other publications listed in the AD.
ADDRESSES: For service information identified in this AD, contact
Boeing Commercial Airplanes, Attention: Data & Services Management,
P.O. Box 3707, MC 2H-65, Seattle, Washington 98124-2207; telephone 206-
544-5000, extension 1, fax 206-766-5680; e-mail [email protected];
Internet https://www.myboeingfleet.com.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this AD, the regulatory evaluation,
any comments received, and other information. The address for the
Docket Office (telephone 800-647-5527) is the Document Management
Facility, U.S. Department of Transportation, Docket Operations, M-30,
West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE.,
Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT: Ivan Li, Aerospace Engineer, Airframe
Branch, ANM-120S, FAA, Seattle Aircraft Certification Office, 1601 Lind
Avenue, SW., Renton, Washington 98057-3356; telephone (425) 917-6437;
fax (425) 917-6590.
SUPPLEMENTARY INFORMATION:
Discussion
The FAA issued a notice of proposed rulemaking (NPRM) to amend 14
CFR part 39 to include an AD that supersedes AD 94-12-04, Amendment 39-
8932 (59 FR 30277, June 13, 1994). The existing AD applies to certain
Model 747 airplanes. That NPRM was published in the Federal Register on
November 18, 2009 (74 FR 59488). That NPRM proposed to continue to
require repetitive inspections to detect cracking in certain fuselage
skin lap joints, and repair if necessary. That NPRM also proposed to
expand the inspection area in the existing AD, add a modification of
certain lap joints, and add certain post-repair inspections of the lap
joints. That NPRM specified that accomplishing the modification would
end the repetitive inspections required by the existing AD for the
length of lap joint that is modified.
Comments
We provided the public the opportunity to participate in the
development of this AD. We have considered the comments that have been
received on the NPRM.
Request for Certain Clarifications
Boeing asks that we provide the following clarifications:
Include language in paragraph (c) of the NPRM which
specifies that airplanes having line number 629, 635, 637, 650, 666,
667, 673, 675, 683, 713, 750, or 810 are Group 5 airplanes. Boeing
states that after Boeing Service Bulletin 747-53A2367, Revision 3,
dated January 15, 2009, was released, it was determined that these
airplanes do not have a lower lobe air stair door and should have been
included in Group 5, not Group 10.
We agree with Boeing's request for the reason provided. The
airplane grouping is incorrect in Boeing Alert Service Bulletin 747-
53A2367, Revision 2, dated October 30, 2008, and Boeing Service
Bulletin 747-53A2367, Revision 3, dated January 15, 2009. Therefore, we
have added a new Note 1 after paragraph (c) of this AD to clarify the
correct airplane grouping for airplanes having the identified line
numbers.
Change the term ``Delegation Option Authorization'' (DOA)
to ``Organization Designation Authorization'' (ODA) throughout the
NPRM.
We agree. Boeing Commercial Airplanes has received an Organization
Designation Authorization (ODA), which replaces the previous
designation as a Delegation Option Authorization (DOA) holder. We have
changed paragraph (m)(3) of this AD to add delegation of authority to
Boeing Commercial Airplanes ODA to approve an alternative method of
compliance for any repair required by this AD.
Change the Discussion section of the NPRM to note that AD
2009-04-16, Amendment 39-15822 (74 FR 8737, February 26, 2009),
supersedes AD 2008-10-15, Amendment 39-15522 (73 FR 29042, May 20,
2008). Although we agree that AD 2009-04-16 superseded AD 2008-10-15,
the discussion section of the NPRM is not carried over to this final
rule. Therefore, we have made no change to the AD in this regard.
[[Page 27425]]
Change the terminating action language specified in
paragraph (j) of the NPRM to add the following at the end of the last
sentence in that paragraph: ``* * * for a period of 15,000 flight
cycles. Additional work is required for continued operation beyond
15,000 flight-cycles after the modification.'' Boeing states that a
post-modification inspection is specified in a note following Table 2
of paragraph 1.E. of Boeing Service Bulletin 747-53A2367, Revision 3,
dated January 15, 2009.
We do not agree with Boeing's request. The note following Table 2
of paragraph 1.E. of the service bulletin specifies that additional
work is required for continued operation beyond 15,000 flight cycles
after the modification, and that Boeing must be contacted for
instructions. Considering the compliance time of 30,000 total flight
cycles for the modification, and the compliance time for additional
work, we have determined that rulemaking on the undefined additional
work is not necessary at this time. We will consider future rulemaking
once the additional work is defined. We have made no change to the AD
in this regard.
Add a new paragraph (j)(1) to the NPRM to state that at
all lap joint areas not covered by the modification required by
paragraph (j) of this AD, a lap joint modification must be installed at
35,000 total flight cycles. Boeing states that the NPRM should reflect
the structural modification point (SMP) for all lap splices not
modified by Boeing Service Bulletin 747-53A2367, Revision 3, dated
January 15, 2009, as stated on page 26, section 1.D., Note 7, of that
service bulletin.
We do not agree with Boeing's request. Notes in the Description
section of a service bulletin are considered informational only. In
addition, the subject note specifies modification of all lap joints not
covered by the modification specified in Boeing Service Bulletin 747-
53A2367. The compliance time specified in that note in Boeing Service
Bulletin 747-53A2367, Revision 3, dated January 15, 2009, is 35,000
total flight cycles, and Boeing is not planning to provide engineering
drawings for that modification. Modification of those lap joints is not
included in this AD. We will consider future rulemaking when
modification procedures are available. We have made no change to the AD
in this regard.
Explanation of Change Made to This AD
We have changed this AD to identify the legal name of the
manufacturer as published in the most recent type certificate data
sheet for the affected airplane models.
Conclusion
We reviewed the relevant data, considered the comments received,
and determined that air safety and the public interest require adopting
the AD with the changes described previously. We also determined that
these changes will not increase the economic burden on any operator or
increase the scope of the AD.
Explanation of Change to Costs of Compliance
After the NPRM was issued, we reviewed the figures we have used
over the past several years to calculate AD costs to operators. To
account for various inflationary costs in the airline industry, we find
it necessary to increase the labor rate used in these calculations from
$80 per work hour to $85 per work hour. The cost impact information,
below, reflects this increase in the specified hourly rate.
Costs of Compliance
There are 209 airplanes of the affected design in the worldwide
fleet. This AD affects about 69 airplanes of U.S. registry.
The actions that are required by AD 94-12-04 and retained in this
AD take about 14 work hours per airplane, at an average labor rate of
$85 per work hour. Based on these figures, the estimated cost of the
currently required actions is $1,190 per airplane, per inspection
cycle.
The new Area 2 inspections take up to 477 work hours per airplane,
depending on airplane configuration, at an average labor rate of $85
per work hour. Based on these figures, the estimated cost of the new
inspections specified in this AD for U.S. operators is up to
$2,797,605, or up to $40,545 per airplane, per inspection cycle.
The new modification takes about 171 work hours per airplane, at an
average labor rate of $85 per work hour. Required parts cost per
airplane will be minimal. Based on these figures, the estimated cost of
the new actions specified in this AD for U.S. operators is $1,002,915,
or $14,535, per airplane.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We have determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866;
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this AD and placed it in the AD docket. See the ADDRESSES
section for a location to examine the regulatory evaluation.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
0
Accordingly, under the authority delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The Federal Aviation Administration (FAA) amends Sec. 39.13 by
removing Amendment 39-8932 (59 FR 30277, June 13, 1994) and by adding
the following new airworthiness directive (AD):
[[Page 27426]]
2010-10-05 The Boeing Company: Amendment 39-16284. Docket No. FAA-
2009-1066; Directorate Identifier 2009-NM-028-AD.
Effective Date
(a) This AD becomes effective June 21, 2010.
Affected AD
(b) This AD supersedes AD 94-12-04, Amendment 39-8932.
Applicability
(c) This AD applies to The Boeing Company Model 747-100, 747-
100B, 747-100B SUD, 747-200B, 747-300, 747SR, and 747SP series
airplanes, certificated in any category, as identified in Boeing
Service Bulletin 747-53A2367, Revision 3, dated January 15, 2009.
Note 1: Airplanes having line number 629, 635, 637, 650, 666,
667, 673, 675, 683, 713, 750, or 810 are Group 5 airplanes.
Subject
(d) Air Transport Association (ATA) of America Code 53:
Fuselage.
Unsafe Condition
(e) This AD results from a structural review of affected skin
lap joints for widespread fatigue damage. The Federal Aviation
Administration is issuing this AD to prevent fatigue cracking in
certain lap joints, which could result in rapid depressurization of
the airplane.
Compliance
(f) You are responsible for having the actions required by this
AD performed within the compliance times specified, unless the
actions have already been done.
Restatement of Requirements of AD 94-12-04, With Revised Service
Information
Repetitive Inspections
(g) For airplanes identified in Boeing Service Bulletin 747-53-
2367, dated December 18, 1991: Prior to the accumulation of 22,000
full pressure flight cycles (or, if the external skin panel of an
affected lap joint has been replaced, prior to the accumulation of
22,000 full pressure flight cycles since skin replacement), or
within 1,000 landings after July 13, 1994 (the effective date of AD
94-12-04), whichever occurs later, perform an external surface high
frequency eddy current (HFEC) inspection of the skin around the
upper row of fasteners, in accordance with the Accomplishment
Instructions of Boeing Service Bulletin 747-53-2367, dated December
18, 1991; Boeing Service Bulletin 747-53-2367, Revision 1, dated
January 27, 1994; Boeing Alert Service Bulletin 747-53A2367,
Revision 2, dated October 30, 2008; or Boeing Service Bulletin 747-
53A2367, Revision 3, dated January 15, 2009. As of the effective
date of this AD, only Revision 3 may be used.
(1) If no crack is found, repeat the inspection thereafter at
intervals not to exceed 3,000 full pressure flight cycles until the
inspections required by paragraph (h) of this AD are done.
(2) If any crack is found, accomplish paragraphs (g)(2)(i) and
(g)(2)(ii) of this AD.
(i) Prior to further flight, perform an open hole HFEC
inspection to detect cracking in the upper row fastener holes
between the adjacent frames, in accordance with the Accomplishment
Instructions of Boeing Service Bulletin 747-53-2367, dated December
18, 1991; Boeing Service Bulletin 747-53-2367, Revision 1, dated
January 27, 1994; Boeing Alert Service Bulletin 747-53A2367,
Revision 2, dated October 30, 2008; or Boeing Service Bulletin 747-
53A2367, Revision 3, dated January 15, 2009. Prior to further
flight, repair any crack found, in accordance with a method approved
by the Manager, Seattle Aircraft Certification Office (ACO), FAA.
Note 2: Guidance on repairing cracking can be found in Chapter
53-30-03 of the Boeing 747 Structural Repair Manual.
(ii) Repeat the inspection required by paragraph (g) of this AD
thereafter at intervals not to exceed 3,000 full pressure flight
cycles until the inspections required by paragraph (h) of this AD
are done.
New Requirements of This AD
Repetitive Inspections/Investigative and Corrective Actions
(h) For all airplanes: Do initial and repetitive HFEC
inspections for cracks of lap joints in Sections 41, 42, 44, and 46,
by doing all the actions, including all applicable related
investigative and corrective actions, specified in the
Accomplishment Instructions of Boeing Service Bulletin 747-53A2367,
Revision 3, dated January 15, 2009, except as provided by paragraph
(l) of this AD. Do the inspections at the applicable times specified
in paragraph 1.E. of Boeing Service Bulletin 747-53A2367, Revision
3, dated January 15, 2009, except as required by paragraph (k) of
this AD. Do all applicable related investigative and corrective
actions before further flight. Accomplishing the inspections
required by this paragraph ends the repetitive inspections required
by paragraph (g) of this AD. Do the actions required by paragraph
(h) of this AD until the modification required by paragraph (j) of
this AD is done.
(i) For areas on which a lap joint repair was installed and the
repair doubler is greater than or equal to 40 inches long: Do
initial and repetitive internal HFEC inspections for cracks, as
required by paragraph (h) of this AD, by doing all the applicable
actions, including applicable corrective actions, specified in the
Accomplishment Instructions of Boeing Service Bulletin 747-53A2367,
Revision 3, dated January 15, 2009, except as provided by paragraph
(l) of this AD. Do the inspection and corrective actions at the
times specified in paragraph 1.E. of Boeing Service Bulletin 747-
53A2367, Revision 3, dated January 15, 2009, except as required by
paragraph (k) of this AD.
Terminating Action
(j) Before the accumulation of 30,000 total flight cycles or
within 3,000 flight cycles after the effective date of this AD,
whichever occurs later: Modify the applicable lap joints in Sections
41 and 42 by doing all the actions specified in the Accomplishment
Instructions of Boeing Service Bulletin 747-53A2367, Revision 3,
dated January 15, 2009, except as required by paragraph (l) of this
AD. Accomplishing this modification terminates the repetitive
inspection requirements of this AD for the length of lap joint that
is modified.
Exceptions to Boeing Service Bulletin 747-53A2367, Revision 3, Dated
January 15, 2009
(k) Where Boeing Service Bulletin 747-53A2367, Revision 3, dated
January 15, 2009, specifies compliance times ``from the date on the
original issue of this service bulletin [12/18/91],'' this AD
requires compliance within the specified compliance time after July
13, 1994 (the effective date of AD 94-12-04). Where Boeing Service
Bulletin 747-53A2367, Revision 3, dated January 15, 2009, specifies
compliance times ``after the date on Revision 2 of this service
bulletin [10/30/08],'' this AD requires compliance within the
specified compliance time after the effective date of this AD.
(l) Where Boeing Service Bulletin 747-53A2367, Revision 3, dated
January 15, 2009, specifies to contact Boeing for repair or
modification instructions: Before further flight, repair or modify
using a method approved in accordance with the procedures specified
in paragraph (m) of this AD.
Alternative Methods of Compliance (AMOCs)
(m)(1) The Manager, Seattle ACO, has the authority to approve
AMOCs for this AD, if requested using the procedures found in 14 CFR
39.19. Send information to ATTN: Ivan Li, Aerospace Engineer,
Airframe Branch, ANM-120S, FAA, Seattle ACO, 1601 Lind Avenue, SW.,
Renton, Washington 98057-3356; telephone (425) 917-6437; fax (425)
917-6590. Or, e-mail information to [email protected].
(2) To request a different method of compliance or a different
compliance time for this AD, follow the procedures in 14 CFR 39.19.
Before using any approved AMOC on any airplane to which the AMOC
applies, notify your principal maintenance inspector (PMI) or
principal avionics inspector (PAI), as appropriate, or lacking a
principal inspector, your local Flight Standards District Office.
The AMOC approval letter must specifically reference this AD.
(3) An AMOC that provides an acceptable level of safety may be
used for any repair required by this AD, if it is approved by the
Boeing Commercial Airplanes Organization Designation Authorization
(ODA) that has been authorized by the Manager, Seattle ACO, to make
those findings. For a repair method to be approved, the repair must
meet the certification basis of the airplane, and the approval must
specifically refer to this AD.
(4) AMOCs approved previously in accordance with AD 94-12-04 are
approved as alternative methods of compliance with the corresponding
requirements of this AD.
Material Incorporated by Reference
(n) You must use the service information specified in Table 1 of
this AD, as applicable, to do the actions required by this AD,
unless the AD specifies otherwise.
[[Page 27427]]
Table 1--All Material Incorporated by Reference
----------------------------------------------------------------------------------------------------------------
Document Revision Date
----------------------------------------------------------------------------------------------------------------
Boeing Alert Service Bulletin 747- 2.................................. October 30, 2008.
53A2367.
Boeing Service Bulletin 747-53-2367... Original........................... December 18, 1991.
Boeing Service Bulletin 747-53-2367... 1.................................. January 27, 1994.
Boeing Service Bulletin 747-53A2367... 3.................................. January 15, 2009.
----------------------------------------------------------------------------------------------------------------
(1) The Director of the Federal Register approved the
incorporation by reference of the Boeing service information
specified in Table 2 of this AD under 5 U.S.C. 552(a) and 1 CFR part
51.
Table 2--New Material Incorporated by Reference
------------------------------------------------------------------------
Document Revision Date
------------------------------------------------------------------------
Boeing Alert Service Bulletin 2 October 30, 2008.
747-53A2367.
Boeing Service Bulletin 747- 3 January 15, 2009.
53A2367.
------------------------------------------------------------------------
(2) The Director of the Federal Register previously approved the
incorporation by reference of the Boeing service information
contained in Table 3 of this AD on July 13, 1994 (59 FR 30277, June
13, 1994).
Table 3--Material Previously Incorporated by Reference
----------------------------------------------------------------------------------------------------------------
Document Revision Date
----------------------------------------------------------------------------------------------------------------
Boeing Service Bulletin 747-53-2367... Original........................... December 18, 1991.
Boeing Service Bulletin 747-53-2367... 1.................................. January 27, 1994.
----------------------------------------------------------------------------------------------------------------
(3) For service information identified in this AD, contact
Boeing Commercial Airplanes, Attention: Data & Services Management,
P.O. Box 3707, MC 2H-65, Seattle, Washington 98124-2207; telephone
206-544-5000, extension 1, fax 206-766-5680; e-mail
[email protected]; Internet https://www.myboeingfleet.com.
(4) You may review copies of the service information at the FAA,
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton,
Washington. For information on the availability of this material at
the FAA, call 425-227-1221.
(5) You may also review copies of the service information that
is incorporated by reference at the National Archives and Records
Administration (NARA). For information on the availability of this
material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.
Issued in Renton, Washington, on April 27, 2010.
Ali Bahrami,
Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 2010-10875 Filed 5-14-10; 8:45 am]
BILLING CODE 4910-13-P