[Federal Register Volume 75, Number 94 (Monday, May 17, 2010)]
[Rules and Regulations]
[Pages 27428-27429]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2010-10983]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF LABOR
Occupational Safety and Health Administration
29 CFR Part 1926
Safety Standards for Steel Erection
AGENCY: Occupational Safety and Health Administration, Labor.
ACTION: Final rule; technical amendment.
-----------------------------------------------------------------------
SUMMARY: This technical amendment adds a nonmandatory note to the OSHA
standards governing steel erection. The note provides information
regarding existing Federal Highway Administration regulations that may
apply to employers engaged in activities covered by OSHA's steel
erection standards.
DATES: Effective date: May 17, 2010.
FOR FURTHER INFORMATION CONTACT: General information and press
inquiries: Ms. Jennifer Ashley, Office of Communications, Room N-3647,
OSHA, U.S. Department of Labor, 200 Constitution Avenue, NW.,
Washington, DC 20210; telephone (202) 693-1999.
Technical inquiries: Contact Mr. Levon Schlichter, Directorate of
Construction, Room N-3468, OSHA, U.S. Department of Labor, 200
Constitution Avenue, NW., Washington, DC 20210; telephone (202) 693-
2020 or fax (202) 693-1689.
Electronic copies of this Federal Register notice: Go to OSHA's Web
site (http://www.osha.gov), and select ``Federal Register,'' ``Date of
Publication,'' and then ``2010.''
SUPPLEMENTARY INFORMATION:
Background. On May 15, 2004, a fatal highway accident occurred on
an interstate highway in Colorado as a passenger vehicle passed under
an overpass that was being widened. The bracing used to temporarily
support a partially installed steel girder on the overpass collapsed,
causing the girder to fall to the highway below, shearing off the top
of the vehicle and killing the three occupants inside. The National
Transportation Safety Board (NTSB) subsequently investigated the
accident and determined that the probable cause was insufficient design
and installation of the girder's temporary bracing system. NTSB also
found that a Registered Engineer did not approve the bracing-system
design, which violates Federal Highway Administration (FHWA)
regulations (See discussion in the following paragraph).\1\
---------------------------------------------------------------------------
\1\ The NTSB published the findings of this investigation in
NTSB Safety Recommendation H-06-23, June 29, 2006; see ``Technical
Inquiries'' mentioned earlier to obtain a copy of this document.
---------------------------------------------------------------------------
FHWA regulations generally require employers involved in National
Highway System construction projects to comply with a number of
standards, policies, and standard specifications published by the
American Association of State Highway and Transportation Officials
(``AASHTO''), among other organizations (See 23 CFR 625.3, 625.4). FHWA
also encourages compliance with AASHTO Specifications that the FHWA
regulations do not currently incorporate by reference. (See http://www.fhwa.dot.gov/bridge/lrfd/index.htm.)
For projects involving bridge construction (e.g., temporary bracing
systems), the FHWA regulations incorporate by reference AASHTO's
Standard Specifications for Highway Bridges, 15th edition, 1992 (See 23
CFR 625.4). The 1992 Specifications provide that a Registered Engineer
must prepare and seal working drawings for falsework in many cases.
OSHA believes that knowledge of these requirements will enhance the
safety of employees operating on or near structural steel elements used
in highway construction, including bridges and other structures.
Therefore, OSHA is adding a note to 29 CFR 1926.754(a) to inform
construction employers of the FHWA requirements.
[[Page 27429]]
Public participation. OSHA determined that this technical amendment
is not subject to the procedures for public notice and comment
specified by Section 4 of the Administrative Procedures Act (5 U.S.C.
553), Section 6(b) of the Occupational Safety and Health Act of 1970
(29 U.S.C. 655(b)), and 29 CFR 1911.5. This technical amendment of 29
CFR 1926.754(a) merely notifies the regulated community of existing
Federal regulations; it is nonmandatory and disseminated for
informational purposes only, and does not increase regulatory burden.
Therefore, this technical amendment does not affect or change any
existing rights or obligations, and no member of the regulated
community is likely to object to it. In conclusion, OSHA finds good
cause that the opportunity for public comment is unnecessary within the
meaning of 5 U.S.C. 553(b)(3)(B), 29 U.S.C. 655(b), and 29 CFR 1911.5.
List of Subjects in 29 CFR Part 1926
Structural steel erection, Construction industry, Construction
safety, Occupational Safety and Health Administration, Occupational
safety and health.
Authority and Signature
This document was prepared under the authority of David Michaels,
PhD, MPH, Assistant Secretary of Labor for Occupational Safety and
Health, U.S. Department of Labor, 200 Constitution Avenue, NW.,
Washington, DC 20210, pursuant to Sections 6(b) of the Occupational
Safety and Health Act of 1970 (29 U.S.C. 655), Secretary of Labor's
Order 5-2007 (72 FR 31160), and 29 CFR part 1911.
Signed at Washington, DC, on May 4, 2010.
David Michaels,
Assistant Secretary of Labor for Occupational Safety and Health.
0
For the reasons set forth above in the preamble, OSHA is amending 29
CFR part 1926 as follows:
PART 1926--[AMENDED]
Subpart R--[Amended]
0
1. The authority citation for subpart R is revised to read as follows:
Authority: Sec. 107, Contract Work Hours and Safety Standards
Act (Construction Safety Act) (40 U.S.C. 333); Secs. 4, 6, and 8,
Occupational Safety and Health Act of 1970 (29 U.S.C. 653, 655,
657); Secretary of Labor's Order Nos. 3-2000 (65 FR 50017), 5-2002
(67 FR 65008), and 5-2007 (72 FR 31160); and 29 CFR part 1911.
0
2. Amend Sec. 1926.754 by adding a note after paragraph (a) to read as
follows:
Sec. 1926.754 Structural steel assembly.
(a) * * *
Note to paragraph (a): Federal Highway Administration (FHWA)
regulations incorporate by reference a number of standards,
policies, and standard specifications published by the American
Association of State Highway and Transportation Officials (AASHTO)
and other organizations. (See 23 CFR 625.4). Many of these
incorporated provisions may be relevant to maintaining structural
stability during the erection process. For instance, as of May 17,
2010, in many cases FHWA requires a Registered Engineer to prepare
and seal working drawings for falsework used in highway bridge
construction. (See AASHTO Specifications for Highway Bridges, Div.
II, Sec. 3.2.1, 15th edition, 1992, which FHWA incorporates by
reference in 23 CFR 625.4). FHWA also encourages compliance with
AASHTO Specifications that the FHWA regulations do not currently
incorporate by reference. (See http://www.fhwa.dot.gov/bridge/lrfd/index.htm.)
* * * * *
[FR Doc. 2010-10983 Filed 5-14-10; 8:45 am]
BILLING CODE 4510-26-P