[Federal Register Volume 75, Number 170 (Thursday, September 2, 2010)]
[Proposed Rules]
[Pages 53908-53914]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2010-21954]
-----------------------------------------------------------------------
ENVIRONMENTAL PROTECTION AGENCY
40 CFR Part 60
[EPA-HQ-OAR-2010-0115; FRL-9195-9]
RIN 2060-AQ23
Method 16C for the Determination of Total Reduced Sulfur
Emissions From Stationary Sources
AGENCY: Environmental Protection Agency (EPA).
ACTION: Proposed rule.
-----------------------------------------------------------------------
SUMMARY: This action proposes a method for measuring total reduced
sulfur (TRS) emissions from stationary sources. The EPA is making this
method available for general use as requested by a number of source
testing companies since it has been allowed for use in the past on a
case-by-case basis for kraft pulp mills and refineries. This proposed
method would offer advantages over
[[Page 53909]]
current methods in that real-time data are acquired and testers are
allowed to use analyzers and procedures for measuring TRS that are
commonly used to measure sulfur dioxide (SO2). The proposed
method would offer an alternative to methods that are currently
required.
DATES: Comments must be received on or before November 1, 2010.
ADDRESSES: Submit your comments, identified by Docket ID No. EPA-HQ-
OAR-2010-0115, by one of the following methods:
http://www.regulations.gov: Follow the on-line
instructions for submitting comments.
E-mail: [email protected], attention Docket ID No.
EPA-HQ-OAR-2010-0115.
Fax: (202) 566-9744, attention Docket ID No. EPA-HQ-OAR-
2010-0115.
Mail: Method 16C for the Determination of Total Reduced
Sulfur Emissions from Stationary Sources, Docket ID No. EPA-HQ-OAR-
2010-0115. Environmental Protection Agency, Mailcode: 2822T, 1200
Pennsylvania Ave., NW., Washington, DC 20460. Please include a total of
two copies.
Hand Delivery: Deliver your comments to EPA Docket Center,
Public Reading Room, EPA West, Room 3334, 1301 Constitution Ave., NW.,
Washington, DC 20460, attention Docket ID No. EPA-HQ-OAR-2010-0115.
Such deliveries are only accepted during the Docket's normal hours of
operation, and special arrangements should be made for deliveries of
boxed information.
Instructions: Direct your comments to Docket ID No. EPA-HQ-OAR-
2010-0115. EPA's policy is that all comments received will be included
in the public docket without change and may be made available online at
http://www.regulations.gov, including any personal information
provided, unless the comment includes information claimed to be
confidential business information (CBI) or other information whose
disclosure is restricted by statute. Do not submit information that you
consider to be CBI or otherwise protected through http://www.regulations.gov or e-mail. The http://www.regulations.gov Web site
is an ``anonymous access'' system, which means EPA will not know your
identity or contact information unless you provide it in the body of
your comment. If you send an e-mail comment directly to EPA without
going through http://www.regulations.gov, your e-mail address will be
automatically captured and included as part of the comment that is
placed in the public docket and made available on the Internet. If you
submit an electronic comment, EPA recommends that you include your name
and other contact information in the body of your comment and with any
disk or CD-ROM you submit. If EPA cannot read your comment due to
technical difficulties and cannot contact you for clarification, EPA
may not be able to consider your comment. Electronic files should avoid
the use of special characters, any form of encryption, and be free of
any defects or viruses. For additional information about EPA's public
docket, visit the EPA Docket Center homepage at http://www.epa.gov/epahome/dockets.htm.
Docket: All documents in the docket are listed in the http://www.regulations.gov index. Although listed in the index, some
information is not publicly available, e.g., CBI or other information
whose disclosure is restricted by statute. Certain other material, such
as copyrighted material, will be publicly available only in hard copy.
Publicly available docket materials are available either electronically
in http://www.regulations.gov or in hard copy at the Method 16C for the
Determination of Total Reduced Sulfur Emissions from Stationary Sources
Docket, EPA/DC, EPA West, Room 3334, 1301 Constitution Ave., NW.,
Washington, DC. The Public Reading Room is open from 8:30 a.m. to 4:30
p.m., Monday through Friday, excluding legal holidays. The telephone
number for the Public Reading Room is (202) 566-1744, and the telephone
number for the Air Docket is (202) 566-1742.
FOR FURTHER INFORMATION CONTACT: Mr. Foston Curtis, U.S. Environmental
Protection Agency, Office of Air Quality Planning and Standards, Air
Quality Assessment Division (E143-02), Research Triangle Park, NC
27711; telephone number: (919) 541-1063; fax number: (919) 541-0516;
and e-mail address: [email protected].
SUPPLEMENTARY INFORMATION:
I. General Information
A. Does this action apply to me?
Method 16C applies to the measurement of TRS at kraft pulp mills
subject to Subpart BB of the New Source Performance Standards (NSPS).
Currently, Methods 16, 16A, and 16B are allowed at these facilities.
Method 16C would offer an additional alternative. The methods required
under Subpart BB are sometimes used in special cases under the
petroleum refineries NSPS (Subpart J). Method 16C may be applicable to
other sources regulated by State and local regulations that specify the
use of Methods 16, 16A, or 16B if desired. The entities that are
potentially affected by this proposal are included in the following
table.
------------------------------------------------------------------------
Examples of regulated
Category NAICS \a\ entities
------------------------------------------------------------------------
Industry.......................... 324110 Petroleum Refineries.
Industry.......................... 322110 Kraft Pulp Mills.
------------------------------------------------------------------------
\a\ North American Industry Classification System.
B. What should I consider as I prepare my comments for EPA?
1. Submitting CBI. Do not submit this information to EPA through
http://www.regulations.gov or e-mail. Clearly mark any of the
information that you claim to be CBI. For CBI information in a disk or
CD-ROM that you mail to EPA, mark the outside of the disk or CD-ROM as
CBI and then identify electronically within the disk or CD-ROM the
specific information that is claimed as CBI. In addition to one
complete version of the comment that includes information claimed as
CBI, a copy of the comment that does not contain the information
claimed as CBI must be submitted for inclusion in the public docket.
Information so marked will not be disclosed except in accordance with
procedures set forth in 40 CFR part 2.
2. Tips for Preparing Your Comments. When submitting comments,
remember to:
Identify the rulemaking by docket number and other
identifying information (subject heading, Federal Register date and
page number).
Follow directions--The agency may ask you to respond to
specific questions or organize comments by referencing a Code of
Federal Regulations (CFR) part or section number.
Explain why you agree or disagree, suggest alternatives,
and substitute language for your requested changes.
Describe any assumptions and provide any technical
information and/or data that you used.
If you estimate potential costs or burdens, explain how
you arrived at your estimate in sufficient detail to allow for it to be
reproduced.
Provide specific examples to illustrate your concerns, and
suggest alternatives.
Explain your views as clearly as possible, avoiding the
use of profanity or personal threats.
Make sure to submit your comments by the comment period
deadline identified.
[[Page 53910]]
C. Where can I get a copy of this document?
In addition to being available in the docket, an electronic copy of
this proposed rule is also available on the Worldwide Web (WWW) through
the Technology Transfer Network (TTN). Following the Administrator's
signature, a copy of this proposed rule will be posted on the TTN's
policy and guidance page for newly proposed or promulgated rules at the
following address: http://www.epa.gov/ttn/oarpg/. The TTN provides
information and technology exchange in various areas of air pollution
control.
D. How is this document organized?
The information in this preamble is organized as follows:
I. General Information
A. Does this action apply to me?
B. What should I consider as I prepare my comments for EPA?
C. Where can I get a copy of this document?
D. How is this document organized?
II. Background and Summary of Method 16C
III. Statutory and Executive Order Reviews
A. Executive Order 12866: Regulatory Planning and Review
B. Paperwork Reduction Act
C. Regulatory Flexibility Act
D. Unfunded Mandates Reform Act
E. Executive Order 13132: Federalism
F. Executive Order 13175: Consultation and Coordination With
Indian Tribal Governments
G. Executive Order 13045: Protection of Children From
Environmental Health Risks and Safety Risks
H. Executive Order 13211: Actions Concerning Regulations That
Significantly Affect Energy Supply, Distribution, or Use
I. National Technology Transfer Advancement Act
J. Executive Order 12898: Federal Actions To Address
Environmental Justice in Minority Populations and Low-Income
Populations
II. Background and Summary of Method 16C
The EPA is making Method 16C available for general use as requested
by a number of source testing companies since it has been allowed on a
case-by-case basis in the past. The proposed method would offer an
alternative to methods that are currently required.
Method 16C uses the sampling procedures of Method 16A and the
analytical procedures of Method 6C to measure TRS. Total reduced sulfur
is defined as hydrogen sulfide, methyl mercaptan, dimethyl sulfide, and
dimethyl disulfide. As described in Method 16A, the sample is collected
from the source through a heated probe and immediately conditioned in a
citrate buffer scrubber. The conditioned sample is oxidized in a tube
furnace to convert TRS to sulfur dioxide (SO2). The oxidized
sample is then analyzed for SO2 using a real-time
SO2 analyzer as prescribed in Method 6C. In this method, we
are combining the proven combustion process of Method 16A with the
analytical techniques currently used for SO2 to form a new,
improved method for measuring TRS.
This method would become available as an option for use in
connection with the New Source Performance Standards for kraft pulp
mills and possibly petroleum refineries. We have allowed its use in
approximately four tests over the past 10 years on a case-by-case basis
and, based on our experience, it is a good alternative. Method 16C
offers advantages over currently required methods by supplying real-
time data in the field using analyzers and procedures that are
currently used for other pollutants. Performance checks are contained
in the method to ensure that bias and calibration precision are
periodically checked and maintained.
This rule will not require the use of Method 16C but will allow it
as an alternative method at the discretion of the user. This method
does not impact testing stringency; data are collected under the same
conditions and time intervals as the current methods.
III. Statutory and Executive Order Reviews
A. Executive Order 12866: Regulatory Planning and Review
This action is not a ``significant regulatory action'' under the
terms of Executive Order (EO)12866 (58 FR 51735, October 4, 1993) and
is therefore not subject to review under the EO.
B. Paperwork Reduction Act
This action does not impose an information collection burden under
the provisions of the Paperwork Reduction Act, 44 U.S.C. 3501 et seq.
Burden is defined at 5 CFR 1320.3(b). The method being proposed in this
action does not add information collection requirements but makes an
additional optional procedure available for use by affected parties.
C. Regulatory Flexibility Act
The Regulatory Flexibility Act (RFA) generally requires an agency
to prepare a regulatory flexibility analysis of any rule subject to
notice and comment rulemaking requirements under the Administrative
Procedure Act or any other statute unless the agency certifies that the
rule will not have a significant economic impact on a substantial
number of small entities. Small entities include small businesses,
small organizations, and small governmental jurisdictions.
For purposes of assessing the impacts of today's rule on small
entities, small entity is defined as (1) A small business as defined by
the Small Business Administration's (SBA) regulations at 13 CFR
121.201; (2) a small governmental jurisdiction that is a government of
a city, county, town, school district or special district with a
population of less than 50,000; and (3) a small organization that is
any not-for-profit enterprise which is independently owned and operated
and is not dominant in its field.
After considering the economic impacts of today's proposed rule on
small entities, I certify that this action will not have a significant
economic impact on a substantial number of small entities. This
rulemaking does not impose emission measurement requirements beyond
those specified in the current regulations, nor does it change any
emission standard. As such, it will not present a significant economic
impact on a substantial number of small businesses.
We continue to be interested in the potential impacts of the
proposed rule on small entities and welcome comments on issues related
to such impacts.
D. Unfunded Mandates Reform Act
This action contains no Federal mandates under the provisions of
Title II of the Unfunded Mandates Reform Act of 1995 (UMRA), 2 U.S.C.
1531-1538 for State, local, or tribal governments or the private
sector. The action imposes no enforceable duty on any State, local or
tribal governments or the private sector. Therefore, this action is not
subject to the requirements of sections 202 or 205 of the UMRA. This
action is also not subject to the requirements of section 203 of UMRA
because it contains no regulatory requirements that might significantly
or uniquely affect small governments. This action makes available a new
optional method for measuring pollutants but adds no new requirements.
E. Executive Order 13132: Federalism
This action does not have federalism implications. It will not have
substantial direct effects on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government, as
specified in Executive Order 13132. This action simply makes an
optional test method
[[Page 53911]]
available for affected sources who desire to use it. Thus, Executive
Order 13132 does not apply to this action. In the spirit of Executive
Order 13132, and consistent with EPA policy to promote communications
between EPA and State and local governments, EPA specifically solicits
comment on this proposed rule from State and local officials.
F. Executive Order 13175: Consultation and Coordination With Indian
Tribal Governments
This action does not have tribal implications, as specified in
Executive Order 13175 (65 FR 67249, November 9, 2000). This action
makes available a new optional method for measuring pollutants but adds
no new requirements. Thus, Executive Order 13175 does not apply to this
action. EPA specifically solicits additional comment on this proposed
action from tribal officials.
G. Executive Order 13045: Protection of Children From Environmental
Health Risks and Safety Risks
EPA interprets EO 13045 (62 FR 19885, April 23, 1997) as applying
only to those regulatory actions that concern health or safety risks,
such that the analysis required under section 5-501 of the EO has the
potential to influence the regulation. This action is not subject to EO
13045 because it does not establish an environmental standard intended
to mitigate health or safety risks.
H. Executive Order 13211: Actions Concerning Regulations That
Significantly Affect Energy Supply, Distribution, or Use
This action is not subject to Executive Order 13211 (66 FR 28355
(May 22, 2001)), because it is not a significant regulatory action
under Executive Order 12866.
I. National Technology Transfer and Advancement Act
Section 12(d) of the National Technology Transfer and Advancement
Act of 1995 (``NTTAA''), Public Law 104-113 (15 U.S.C. 272 note)
directs EPA to use voluntary consensus standards in its regulatory
activities unless to do so would be inconsistent with applicable law or
otherwise impractical. Voluntary consensus standards are technical
standards (e.g., materials specifications, test methods, sampling
procedures, and business practices) that are developed or adopted by
voluntary consensus standards bodies. NTTAA directs EPA to provide
Congress, through OMB, explanations when the Agency decides not to use
available and applicable voluntary consensus standards. This proposed
rulemaking does not involve technical standards.
J. Executive Order 12898: Federal Actions To Address Environmental
Justice in Minority Populations and Low-Income Populations
Executive Order (EO) 12898 (59 FR 7629 (Feb. 16, 1994)) establishes
Federal executive policy on environmental justice. Its main provision
directs Federal agencies, to the greatest extent practicable and
permitted by law, to make environmental justice part of their mission
by identifying and addressing, as appropriate, disproportionately high
and adverse human health or environmental effects of their programs,
policies, and activities on minority populations and low-income
populations in the United States.
EPA has determined that this proposed rule will not have
disproportionately high and adverse human health or environmental
effects on minority or low-income populations because it does not
affect the level of protection provided to human health or the
environment. This rule adds an optional test method and does not cause
emission increases from regulated sources.
Method 16C for the Determination of Total Reduced Sulfur Emissions From
Stationary Sources
List of Subjects in 40 CFR Part 60
Environmental protection, Air pollution control, Test methods and
procedures, and Performance specifications.
Dated: August 26, 2010.
Lisa P. Jackson,
Administrator.
For the reasons stated in the preamble, the Environmental
Protection Agency proposes to amend title 40, chapter I of the Code of
Federal Regulations as follows:
PART 60--STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES
1. The authority citation for part 60 continues to read as follows:
Authority: 42 U.S.C. 7401-7601.
2. Add Method 16C to Appendix A-6 to read as follows:
APPENDIX A-6 TO PART 60--TEST METHODS 16 THROUGH 18
* * * * *
METHOD 16C--DETERMINATION OF TOTAL REDUCED SULFUR EMISSIONS FROM
STATIONARY SOURCES
1.0 Scope and Application
What is method 16C?
Method 16C is a procedure for measuring total reduced sulfur
(TRS) in stationary source emissions using a continuous instrumental
analyzer. Quality assurance and quality control requirements are
included to assure that you, the tester, collect data of known
quality. You must document your adherence to these specific
requirements for equipment, supplies, sample collection and
analysis, calculations, and data analysis. This method does not
completely describe all equipment, supplies, and sampling and
analytical procedures you will need but refers to other methods for
some of the details. Therefore, to obtain reliable results, you
should also have a thorough knowledge of these additional test
methods which are found in appendix A to this part:
(a) Method 6C--Determination of Sulfur Dioxide Emissions from
Stationary Sources (Instrumental Analyzer Procedure)
(b) Method 7E--Determination of Nitrogen Oxides Emissions from
Stationary Sources (Instrumental Analyzer Procedure)
(c) Method 16A--Determination of Total Reduced Sulfur Emissions
from Stationary Sources (Impinger Technique)
1.1 Analytes. What does Method 16C determine?
------------------------------------------------------------------------
Analyte CAS No.
------------------------------------------------------------------------
Total reduced sulfur including........................ N/A
Dimethyl disulfide (DMDS), [(CH3)2S2]............. 62-49-20
Dimethyl sulfide (DMS), [(CH3)2S]................. 75-18-3
Hydrogen sulfide (H2S)............................ 7783-06-4
Methyl mercaptan (MeSH), [CH4S]................... 74-93-1
Reported as: Sulfur dioxide (SO2)..................... 7449-09-5
------------------------------------------------------------------------
1.2 Applicability. This method is applicable for determining TRS
emissions from recovery furnaces (boilers), lime kilns, and smelt
dissolving tanks at kraft pulp mills, and from other sources when
specified in an applicable subpart of the regulations.
[[Page 53912]]
1.3 Data Quality Objectives. Adherence to the requirements
described in Method 16C will enhance the quality of the data
obtained from air pollutant sampling methods.
2.0 Summary of Method
2.1 An integrated gas sample is extracted from the stack. The
SO2 is removed selectively from the sample using a citrate buffer
solution. The TRS compounds are then thermally oxidized to SO2 and
determined as SO2 by an instrumental analyzer. This method is a
combination of the sampling procedures of Method 16A and the
analytical procedures of Method 6C (referenced in Method 7E), with
minor modifications to facilitate their use together.
3.0 Definitions
Analyzer calibration error, Calibration curve, Calibration gas,
Low-level gas, Mid-level gas, High-level gas, Calibration drift,
Calibration span, Data recorder, Direct calibration mode, Gas
analyzer, Interference check, Measurement system, Response time,
Run, System calibration mode, System performance check, and Test are
the same as used in Methods 16A and 6C.
4.0 Interferences
4.1 Reduced sulfur compounds other than those regulated by the
emission standards, if present, may be measured by this method.
Compounds like carbonyl sulfide, which is partially oxidized to
SO2 and may be present in a lime kiln exit stack, would
be a positive interferent. Interferences may vary among instruments,
and instrument-specific interferences must be evaluated through the
interference check.
4.2 Particulate matter from the lime kiln stack gas (primarily
calcium carbonate) can cause a negative bias if it is allowed to
enter the citrate scrubber; the particulate matter will cause the pH
to rise and H2S to be absorbed before oxidation. Proper
use of the particulate filter, described in Section 6.1.3 of Method
16A, will eliminate this interference.
5.0 Safety
5.1 Disclaimer. This method may involve hazardous materials,
operations, and equipment. This test method may not address all of
the safety problems associated with its use. It is the
responsibility of the user to establish appropriate safety and
health practices before performing this test method.
5.2 Hydrogen Sulfide. Hydrogen sulfide is a flammable, poisonous
gas with the odor of rotten eggs. Hydrogen sulfide is extremely
hazardous and can cause collapse, coma, and death within a few
seconds of one or two inhalations at sufficient concentrations. Low
concentrations irritate the mucous membranes and may cause nausea,
dizziness, and headache after exposure. It is the responsibility of
the user of this test method to establish appropriate safety and
health practices.
6.0 Equipment and Supplies
What do I need for the measurement system? The measurement
system is similar to those applicable components in Methods 16A and
6C. An example measurement system is shown in Figure 16C-1 and
component parts are discussed below. Modifications to the apparatus
are accepted provided the performance criteria in Section 13.0 are
met.
6.1 Probe. Teflon tubing, 6.4-mm (\1/4\-in.) diameter,
sequentially wrapped with heat-resistant fiber strips, a rubberized
heat tape (plug at one end), and heat-resistant adhesive tape. A
flexible thermocouple or other suitable temperature measuring device
must be placed between the Teflon tubing and the fiber strips so
that the temperature can be monitored to prevent softening of the
probe. The probe must be sheathed in stainless steel to provide in-
stack rigidity. A series of bored-out stainless steel fittings
placed at the front of the sheath will prevent moisture and
particulate from entering between the probe and sheath. A 6.4-mm
(\1/4\-in.) Teflon elbow (bored out) must be attached to the inlet
of the probe, and a 2.54 cm (1 in.) piece of Teflon tubing must be
attached at the open end of the elbow to permit the opening of the
probe to be turned away from the particulate stream; this will
reduce the amount of particulate drawn into the sampling train. The
probe is depicted in Figure 16A-2 of Method 16A.
6.2 Probe Brush. Nylon bristle brush with handle inserted into a
3.2-mm (\1/8\-in.) Teflon tubing. The Teflon tubing should be long
enough to pass the brush through the length of the probe.
6.3 Particulate Filter. 50-mm Teflon filter holder and a 1- to
2-[mu]m porosity, Teflon filter (may be available through Savillex
Corporation, 5325 Highway 101, Minnetonka, Minnesota 55343, or other
suppliers of filters). The filter holder must be maintained in a hot
box at a temperature sufficient to prevent moisture condensation. A
temperature of 121 [deg]C (250 [deg]F) was found to be sufficient
when testing a lime kiln under sub-freezing ambient conditions.
6.4 SO2 Scrubber. Three 300-ml Teflon segmented
impingers connected in series with flexible, thick-walled, Teflon
tubing. (Impinger parts and tubing may be available through Savillex
or other suppliers.) The first two impingers contain 100 ml of
citrate buffer, and the third impinger is initially dry. The tip of
the tube inserted into the solution should be constricted to less
than 3 mm (\1/8\-in.) ID and should be immersed to a depth of at
least 5 cm (2 in.).
6.5 Combustion Tube. Quartz glass tubing with an expanded
combustion chamber 2.54 cm (1 in.) in diameter and at least 30.5 cm
(12 in.) long. The tube ends should have an outside diameter of 0.6
cm (\1/4\-in.) and be at least 15.3 cm (6 in.) long. This length is
necessary to maintain the quartz-glass connector near ambient
temperature and thereby avoid leaks. Alternative combustion tubes
are acceptable provided they are shown to combust TRS at
concentrations encountered during tests.
6.6 Furnace. A furnace of sufficient size to enclose the
combustion chamber of the combustion tube with a temperature
regulator capable of maintaining the temperature at 800
100 [deg]C (1472 180 [deg]F). The furnace operating
temperature should be checked with a thermocouple to ensure
accuracy.
6.7 Sampling Pump. A leak-free pump is required to pull the
sample gas through the system at a flow rate sufficient to minimize
the response time of the measurement system and constructed of
material that is non-reactive to the gas it contacts. For dilution-
type measurement systems, an eductor pump may be used to create a
vacuum that draws the sample through a critical orifice at a
constant rate.
6.8 Calibration Gas Manifold. The calibration gas manifold must
allow the introduction of calibration gases either directly to the
gas analyzer in direct calibration mode or into the measurement
system, at the probe, in system calibration mode, or both, depending
upon the type of system used. In system calibration mode, the system
must be able to flood the sampling probe and vent excess gas.
Alternatively, calibration gases may be introduced at the
calibration valve following the probe. Maintain a constant pressure
in the gas manifold. For in-stack dilution-type systems, a gas
dilution subsystem is required to transport large volumes of
purified air to the sample probe and a probe controller is needed to
maintain the proper dilution ratio.
6.9 Sample Gas Manifold. The sample gas manifold diverts a
portion of the sample to the analyzer, delivering the remainder to
the by-pass discharge vent. The manifold should also be able to
introduce calibration gases directly to the analyzer. The manifold
must be made of material that is non-reactive to SO2 and
be configured to safely discharge the bypass gas.
6.10 SO2 Analyzer. You must use an instrument that
uses an ultraviolet, non-dispersive infrared, fluorescence, or other
detection principle to continuously measure SO2 in the
gas stream provided it meets the performance specifications in
Section 13.0.
6.11 Data Recording. A strip chart recorder, computerized data
acquisition system, digital recorder, or data logger for recording
measurement data must be used.
7.0 Reagents and Standards
Note: Unless otherwise indicated, all reagents must conform to
the specifications established by the Committee on Analytical
Reagents of the American Chemical Society. When such specifications
are not available, the best available grade must be used.
7.1 Water. Deionized distilled water must conform to ASTM
Specification D 1193-77 or 91 Type 3 (incorporated by reference--see
Sec. 60.17). The KMnO4 test for oxidizable organic
matter may be omitted when high concentrations of organic matter are
not expected to be present.
7.2 Citrate Buffer. Dissolve 300 g of potassium citrate (or 284
g of sodium citrate) and 41 g of anhydrous citric acid in 1 liter of
water (200 ml is needed per test). Adjust the pH to between 5.4 and
5.6 with potassium citrate or citric acid, as required.
7.3 Calibration Gas. Refer to Section 7.1 of Method 7E (as
applicable) for the calibration gas requirements. Example
calibration gas mixtures are listed below.
(a) SO2 in nitrogen (N2).
(b) SO2 in air.
(c) SO2 and CO2 in N2.
(d) SO2 and O2 in N2.
(e) SO2/CO2/O2 gas mixture in
N2.
(f) CO2/NOX gas mixture in N2.
[[Page 53913]]
(g) CO2/SO2/NOX gas mixture in
N2.
For fluorescence-based analyzers, the O2 and
CO2 concentrations of the calibration gases as introduced
to the analyzer must be within 1 percent (absolute) O2
and 1 percent (absolute) CO2 of the O2 and
CO2 concentrations of the effluent samples as introduced
to the analyzer. Alternatively, for fluorescence-based analyzers,
use calibration blends of SO2 in air and the nomographs
provided by the vendor to determine the quenching correction factor
(the effluent O2 and CO2 concentrations must
be known). This requirement does not apply to ambient-level
fluorescence analyers that are used in conjunction with sample
dilution systems.
7.4 System Performance Check Gas. You must use hydrogen sulfide
(100 ppmv or less) in nitrogen, stored in aluminum cylinders with
concentration certified by the manufacturer.
Note: Alternatively, hydrogen sulfide recovery gas generated
from a permeation device gravimetrically calibrated and certified at
some convenient operating temperature may be used. The permeation
rate of the device must be such that at the appropriate dilution gas
flow rate, an H2S concentration can be generated in the
range of the stack gas or within 20 percent of the emission
standard.
7.5 Interference Check. Examples of test gases for the
interference check are listed in Table 7E-3 of Method 7E.
8.0 Sample Collection, Preservation, Storage, and Transport
8.1 Pre-sampling Tests. Before measuring emissions, perform the
following procedures:
(a) Calibration gas verification,
(b) Calibration error test,
(c) System performance check,
(d) Verification that the interference check has been satisfied.
8.1.1 Calibration Gas Verification. Obtain a certificate from
the gas manufacturer documenting the quality of the gas. Confirm
that the manufacturer certification is complete and current. Ensure
that your calibration gas certifications have not expired. This
documentation should be available on-site for inspection. To the
extent practicable, select a high-level gas concentration that will
result in the measured emissions being between 20 and 100 percent of
the calibration span.
8.1.2 Analyzer Calibration Error Test. After you have assembled,
prepared, and calibrated your sampling system and analyzer, you must
conduct a 3-point analyzer calibration error test before the first
run and again after any failed system performance check or failed
drift test to ensure the calibration is acceptable. Introduce the
low-, mid-, and high-level calibration gases sequentially to the
analyzer in direct calibration mode. For each calibration gas,
calculate the analyzer calibration error using Equation 16C-1 in
Section 12.2. The calibration error for the low-, mid-, and high-
level gases must not exceed 5 percent or 0.5 ppmv. If the
calibration error specification is not met, take corrective action
and repeat the test until an acceptable 3-point calibration is
achieved.
8.1.3 System Performance Check. Same as in Method 16A, Section
8.5, except samples need not be 30 minutes in duration, and the TRS
sample concentration measured between system performance checks is
corrected by the average of the two system performance samples.
System performance checks are conducted before sampling begins
(optional) and after each sample run (mandatory).
8.1.4 Interference Check. Same as in Method 7E, Section 8.2.7.
8.2 Measurement System Preparation.
8.2.1 For the SO2 scrubber, measure 100 ml of citrate
buffer into the first and second impingers; leave the third impinger
empty. Immerse the impingers in an ice bath, and locate them as
close as possible to the filter heat box. The connecting tubing
should be free of loops. Maintain the probe and filter temperatures
sufficiently high to prevent moisture condensation, and monitor with
a suitable temperature sensor. Prepare the oxidation furnace and
maintain at 800 100 [deg]C (1472 180
[deg]F).
8.2.2 Citrate Scrubber Conditioning Procedure. Condition the
citrate buffer scrubbing solution by pulling stack gas through the
Teflon impingers as described in Section 8.4.1.
8.3 Pretest Procedures. After the complete measurement system
has been set up at the site and deemed to be operational, the
following procedures must be completed before sampling is initiated.
8.3.1 Leak-Check. Appropriate leak-check procedures must be
employed to verify the integrity of all components, sample lines,
and connections. For components upstream of the sample pump, attach
the probe end of the sample line to a manometer or vacuum gauge,
start the pump and pull a vacuum greater than 50 mm (2 in.) Hg,
close off the pump outlet, and then stop the pump and ascertain that
there is no leak for 1 minute. For components after the pump, apply
a slight positive pressure and check for leaks by applying a liquid
(detergent in water, for example) at each joint. Bubbling indicates
the presence of a leak. As an alternative to the initial leak-test,
the system performance check in Section 8.3.2 may be performed to
verify the integrity of components.
8.3.2 Initial System Performance Check. A system performance
check using the test gas (Section 7.4) is required prior to testing
to validate the sampling train components and procedure.
8.4 Sample Collection and Analysis
8.4.1 After performing the required pretest procedures described
in Section 8.1, insert the sampling probe into the test port
ensuring that no dilution air enters the stack through the port.
Condition the sampling system and citrate buffer solution for a
minimum of 15 minutes before beginning analysis. (This
preconditioning may not be necessary if the initial system
performance check is performed.) Begin the sampling and analysis.
Determine the concentration of SO2 for the prescribed
sample or run time. Method 16 defines a test run as sampling over a
period of not less than 3 hours or more than 6 hours when testing
kraft pulp mills. For Method 16C to be consistent with Method 16, a
run may be obtained by: (1) sampling for three 60-minute intervals
or (2) sampling for a 3-hour interval. (Three runs constitute a
test.)
8.5 Post-Run Evaluations
8.5.1 System Performance Check. Perform a post-run system
performance check (Section 8.5 of Method 16A) before replacing the
citrate buffer solution and particulate filter and before the probe
is cleaned. The check results must not exceed the 100
20 percent limit set forth in Section 13.3. If this limit is
exceeded, the intervening run or runs are considered invalid.
However, if the recovery efficiency is not in the 100
20 percent range, but the results do not affect the compliance or
noncompliance status of the affected facility, the Administrator may
decide to accept the results of the compliance test.
8.5.2 Calibration Drift. After a run or series of runs, not to
exceed a 24-hour period after initial calibration, perform a
calibration drift test using a calibration gas (preferably the level
that best approximates the sample concentration) in direct
calibration mode. This drift must not differ from the manufacturer
certified concentration of the gas by more than 3 percent or 0.5
ppm. If the drift exceeds this limit, the intervening run or runs
are considered valid, but a new analyzer calibration test must be
performed and passed before continuing sampling.
9.0 Quality Control
------------------------------------------------------------------------
Quality control
Section measure Effect
------------------------------------------------------------------------
8.1...................... Sampling equipment Ensures accurate
leak-check and measurement of sample
calibration. gas flow rate, sample
volume.
8.1.2.................... Analyzer Establishes initial
calibration error. calibration accuracy
within 2%.
8.3.2, 8.5.1............. System performance Ensures accuracy of
check. sampling/analytical
procedure within 20%.
8.5.2.................... Calibration drift Ensures a stable
test. calibration within 3%.
10.0..................... Interference check. Checks for analytical
interferences.
------------------------------------------------------------------------
[[Page 53914]]
10.0 Calibration
10.1 Calibrate the system using the gases described in Section
7.3. The initial 3-point calibration error test as described in
Section 8.1.2 is required and must meet the specifications in
Section 13 before you start the test. We recommend you conduct an
initial system performance test described in Section 8.1.4 as well
before the test to validate the sampling components and procedures
before sampling. After the test commences, a system performance
check is required after each run. You must include a copy of the
manufacturer's certification of the calibration gases used in the
testing as part of the test report. This certification must include
the 13 documentation requirements in the EPA Traceability Protocol
for Assay and Certification of Gaseous Calibration Standards,
September 1997, as amended August 25, 1999.
11.0 Analytical Procedure
Because sample collection and analysis are performed together
(see Section 8.0), additional discussion of the analytical procedure
is not necessary.
12.0 Calculations and Data Analysis
12.1 Nomenclature
ACE = Analyzer calibration error, percent of calibration span.
BWO = Fraction of volume of water vapor in the gas
stream.
CD = Calibration drift, percent.
CDir = Measured concentration of a calibration gas (low,
mid, or high) when introduced in direct calibration mode, ppmv.
CH2S = Concentration of the system performance check gas,
ppmv H2S.
CS = Measured concentration of the system performance gas
when introduced in system calibration mode, ppmv H2S.
CV = Manufacturer certified concentration of a
calibration gas (low, mid, or high), ppmv SO2.
CSO2 = Sample SO2 concentration, ppmv.
CTRS = Total reduced sulfur concentration corrected for
system performance and adjusted to dry conditions, ppmv.
SP = System performance, percent.
12.2 Analyzer Calibration Error. Use Equation 16C-1 to calculate
the analyzer calibration error for the low-, mid-, and high-level
calibration gases.
[GRAPHIC] [TIFF OMITTED] TP02SE10.008
12.3 System Performance. Use Equation 16C-2 to calculate the
system performance.
[GRAPHIC] [TIFF OMITTED] TP02SE10.009
12.4 Calibration Drift. Use Equation 16C-3 to calculate the
calibration drift at a single concentration level after a run or
series of runs (not to exceed a 24-hr period) from initial
calibration. Compare the calibration gas response to the original
response obtained for the gas in the initial analyzer calibration
test (ACEi).
[GRAPHIC] [TIFF OMITTED] TP02SE10.010
12.5 TRS Concentration as SO2. For each sample or
test run, calculate the arithmetic average of SO2
concentration values (e.g., 1-minute averages). Then calculate the
sample TRS concentration using Equation 16C-4.
[GRAPHIC] [TIFF OMITTED] TP02SE10.011
13.0 Method Performance
13.1 Analyzer Calibration Error. At each calibration gas level
(low, mid, and high), the calibration error must either not exceed
5.0 percent of the calibration gas concentration or
[bond]Cs-Cv[bond] must be <= 0.5 ppmv.
13.2 System Performance. The system performance check result
must be within 20 percent of the system performance gas
concentration. Alternatively, the results are acceptable if
[bond]Cs-Cdir[bond] is <= 0.5 ppmv .
13.3 Calibration Drift. The calibration drift at the end of any
run or series of runs within a 24-hour period must not differ by
more than 3 percent from the original ACE at that level or
[bond]ACEi-ACEn[bond] must not exceed 0.5 ppmv.
13.4 Interference Check. For the analyzer, the total
interference response (i.e., the sum of the interference responses
of all tested gaseous components) must not be greater than 2.50
percent of the calibration span. The results are also acceptable if
the sum of the responses does not exceed 0.5 ppmv for a calibration
span of 5 to 10 ppmv, or 0.2 ppmv for a calibration span < 5 ppmv.
14.0 Pollution Prevention [Reserved]
15.0 Waste Management [Reserved]
16.0 References
1. The references are the same as in Section 16.0 of Method 16,
Section 17.0 of Method 16A, and Section 17.0 of Method 6C.
2. National Council of the Paper Industry for Air and Stream
Improvement, Inc., A Study of TRS Measurement Methods. Technical
Bulletin No. 434. New York, NY. May 1984. 12p.
3. Margeson, J.H., J.E. Knoll, and M.R. Midgett. A Manual Method
for TRS Determination. Draft available from the authors. Source
Branch, Quality Assurance Division, U.S. Environmental Protection
Agency, Research Triangle Park, NC 27711.
17.0 Tables, Diagrams, Flowcharts, and Validation Data [Reserved]
[FR Doc. 2010-21954 Filed 9-1-10; 8:45 am]
BILLING CODE 6560-50-P