[Federal Register Volume 75, Number 237 (Friday, December 10, 2010)]
[Notices]
[Pages 77002-77005]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2010-31048]
-----------------------------------------------------------------------
DEPARTMENT OF LABOR
Occupational Safety and Health Administration
[Docket No. OSHA-2009-0025]
Expansion of the Scope of NRTL Recognition of Underwriters
Laboratories Inc.; Modification to the Scopes of NRTL Recognition of FM
Approvals LLC, Intertek Testing Services NA Inc., and Underwriters
Laboratories Inc.
AGENCY: Occupational Safety and Health Administration (OSHA), Labor.
ACTION: Notice.
-----------------------------------------------------------------------
SUMMARY: This notice announces the Occupational Safety and Health
[[Page 77003]]
Administration's final decision expanding the recognition of
Underwriters Laboratories Inc., (UL) as a Nationally Recognized Testing
Laboratory (NRTL) under 29 CFR 1910.7. This notice also modifies the
scopes of recognition of the following three NRTLs: FM Approvals LLC,
Intertek Testing Services NA Inc., and Underwriters Laboratories Inc.
DATES: The expansion of recognition and modification to the scopes of
recognition becomes effective on December 10, 2010.
FOR FURTHER INFORMATION CONTACT: MaryAnn Garrahan, Director, Office of
Technical Programs and Coordination Activities, NRTL Program,
Occupational Safety and Health Administration, U.S. Department of
Labor, 200 Constitution Avenue, NW., Room N-3655, Washington, DC 20210,
or phone (202) 693-2110.
SUPPLEMENTARY INFORMATION:
Notice of Final Decision
The Occupational Safety and Health Administration (OSHA) hereby
gives notice that it is expanding recognition of Underwriters
Laboratories Inc., (UL) as an NRTL. UL's expansion covers the use of
additional test standards. OSHA's current scope of recognition for UL
is in the following informational Web page: http://www.osha.gov/dts/otpca/nrtl/ul.html.
OSHA recognition of an NRTL signifies that the organization meets
the legal requirements specified in 29 CFR 1910.7. Recognition is an
acknowledgment that the organization can perform independent safety
testing and certification of the specific products covered within its
scope of recognition, and is not a delegation or grant of government
authority. As a result of recognition, employers may use products
approved by the NRTL to meet OSHA standards that require product
testing and certification.
The Agency processes applications by an NRTL for initial
recognition, or for expansion or renewal of this recognition, following
requirements in Appendix A to 29 CFR 1910.7. This appendix requires
that the Agency publish two notices in the Federal Register in
processing such an application. In the first notice, OSHA announces the
application and provides its preliminary finding and, in the second
notice, the Agency provides its final decision on the application.
These notices set forth the NRTL's scope of recognition or
modifications of that scope. OSHA maintains an informational Web page
for each NRTL that details its scope of recognition. These pages are
available from the Web site at http://www.osha.gov/dts/otpca/nrtl/index.html. Each NRTL's scope of recognition has three elements: (1)
The type of products the NRTL may test, with each type specified by its
applicable test standard; (2) the recognized site(s) that has/have the
technical capability to perform the testing and certification
activities for test standards within the NRTL's scope; and (3) the
supplemental program(s) that the NRTL may use, each of which allows the
NRTL to rely on other parties to perform activities necessary for
product testing and certification.
UL submitted an application, dated February 20, 2008, as an
amendment to its application for renewal of recognition. (Ex. 2-UL
expansion application dated 2/20/2008.) This amendment requested an
expansion of recognition to add 98 standards \1\ to UL's scope, and to
delete several test standards from its scope. The NRTL Program staff
determined that 49 of the requested standards are ``appropriate test
standards'' within the meaning of 29 CFR 1910.7(c). UL later modified
its request to reduce the number of the appropriate standards to 35.
(Ex. 3-UL amended expansion application dated 2/16/2010.)
---------------------------------------------------------------------------
\1\ UL requested recognition for ANSI/AAMI ES60601-1:2005, but
OSHA has not yet determined whether this standard may be used by
NRTLs. OSHA will request public comment on the suitability of this
standard in an upcoming Federal Register notice.
---------------------------------------------------------------------------
In connection with this request, NRTL Program staff did not perform
any on-site review of UL's recognized sites. The staff only performed a
comparability analysis,\2\ and recommended expansion of UL's
recognition to include the 35 test standards. The Agency published a
preliminary notice announcing the expansion application in the Federal
Register on April 26, 2010 (79 FR 21664). OSHA requested comments on
the notice by May 11, 2010; OSHA received no comments in response to
this notice. OSHA now is proceeding with this final notice to grant
UL's expansion application.
---------------------------------------------------------------------------
\2\ This analysis involves determining whether the testing and
evaluation requirements of test standards already in an NRTL's scope
are comparable to the requirements in the standards requested by the
NRTL.
---------------------------------------------------------------------------
All public documents pertaining to the UL application are available
for review by contacting the Docket Office, Occupational Safety and
Health Administration, U.S. Department of Labor, 200 Constitution
Avenue, NW., Room N-2625, Washington, DC 20210. These materials also
are available online at http://www.regulations.gov under Docket No.
OSHA-2009-0025.
Final Decision and Order
NRTL Program staff examined UL's application, the comparability
analysis, and other pertinent information. Based upon this examination
and the analysis, OSHA finds that UL meets the requirements of 29 CFR
1910.7 for expansion of its recognition, subject to the limitation and
conditions listed below. Pursuant to the authority granted by 29 CFR
1910.7, OSHA hereby expands the recognition of UL, subject to this
limitation and these conditions.
Limitation
OSHA limits the expansion of UL's recognition to testing and
certification of products for demonstration of conformance to the
following test standards, each of which OSHA determines is an
appropriate test standard within the meaning of 29 CFR 1910.7(c):
IEEE C37.20.4 Indoor AC Switches (1 kV-38 kV) for Use in Metal-Enclosed
Switchgear \a\
IEEE C37.20.6 4.76 kV to 38 kV Rated Grounding and Testing Devices Used
in Enclosures \a\
IEEE C37.23 Metal-Enclosed Bus \a\
IEEE C37.41 High-Voltage Fuses, Distribution Enclosed Single-Pole Air
Switches, Fuse Disconnecting Switches, and Accessories \a\
IEEE C37.74 Subsurface, Vault, and Pad-Mounted Load-Interrupter
Switchgear and Fused Load-Interrupter Switchgear for Alternating
Current Systems Up to 38 kV Switchgear \a\
IEEE C57.12.44 Secondary Network Protectors \a\
ISA 12.12.01 Nonincendive Electrical Equipment for Use in Class I and
II, Division 2 and Class III, Divisions 1 and 2 Hazardous (Classified)
Locations
UL 5C Surface Raceways and Fittings for Use with Data, Signal, and
Control Circuits
UL 283 Air Fresheners and Deodorizers
UL 458 Power Converters/Inverters and Power Converter/Inverter Systems
for Land Vehicles and Marine Crafts \b\
NFPA 496 Purged and Pressurized Enclosures for Electrical Equipment
UL 852 Metallic Sprinkler Pipe for Fire Protection Service
UL 962 Household and Commercial Furnishings \c\
UL 1340 Hoists
UL 1626 Residential Sprinklers for Fire Protection Service
UL 2225 Cables and Cable Fittings for Use in Hazardous (Classified)
Locations
UL 2443 Flexible Sprinkler Hose with Fittings for Fire Protection
Service
UL 5085-2 Low Voltage Transformers--Part 2: General Purpose
Transformers
[[Page 77004]]
UL 60730-2-8 Automatic Electrical Controls for Household and Similar
Use; Part 2: Particular Requirements for Electrically Operated Water
Valves, Including Mechanical Requirements
UL 60745-2-1 Particular Requirements for Drills and Impact Drills
UL 60745-2-3 Particular Requirements for Grinders, Polishers and Disk-
Type Sanders
UL 60745-2-11 Particular Requirements for Reciprocating Saws
UL 60745-2-12 Particular Requirements for Concrete Vibrators
UL 60745-2-14 Particular Requirements for Planers
UL 60745-2-17 Particular Requirements for Routers and Trimmers
UL 60745-2-18 Particular Requirements for Strapping Tools
UL 60745-2-19 Particular Requirements for Jointers
UL 60745-2-2 Particular Requirements for Screwdrivers and Impact
Wrenches
UL 60745-2-20 Particular Requirements for Band Saws
UL 60745-2-21 Particular Requirements for Drain Cleaners
UL 60745-2-4 Particular Requirements for Sanders and Polishers Other
Than Disk Type
UL 60745-2-5 Particular Requirements for Circular Saws
UL 60745-2-6 Particular Requirements for Hammers
UL 60745-2-8 Particular Requirements for Shears and Nibblers
UL 60745-2-9 Particular Requirements for Tappers
Notes:
\a\ Recognition for this standard does not apply to testing and
certification of equipment or materials used in installations
excluded from the provisions of subpart S in 29 CFR 1910 by section
1910.302(a)(2).
\b\ OSHA limits recognition for this standard to testing and
certification of products used within recreational vehicles and
mobile homes.
\c\ OSHA limits recognition of this standard to testing and
certification of the electrical devices falling within the
standard's scope.
The designations and titles of the above test standards were
current at the time of the preparation of this notice.
OSHA limits recognition of any NRTL for a particular test standard
to equipment or materials (i.e., products) for which OSHA standards
require third-party testing and certification before use of the product
in the workplace. Consequently, if a test standard also covers any
product for which OSHA does not require such testing and certification,
an NRTL's scope of recognition does not include that product.
The American National Standards Institute (ANSI) may approve the
test standards listed above as American National Standards. However,
for convenience, we may use the designation of the standards-developing
organization for the standard as opposed to the ANSI designation. Under
the NRTL Program's policy (see OSHA Instruction CPL 1-0.3, Appendix C,
paragraph XIV), any NRTL recognized for a particular test standard may
use either the proprietary version of the test standard or the ANSI
version of that standard. Contact ANSI to determine whether a test
standard is currently ANSI-approved.
Conditions
UL also must abide by the following conditions of the recognition,
in addition to those conditions already required by 29 CFR 1910.7:
1. UL must allow OSHA access to its facilities and records to
ascertain continuing compliance with the terms of its recognition, and
to perform investigations as OSHA deems necessary;
2. If UL has reason to doubt the efficacy of any test standard it
is using under this program, it must promptly inform the test standard-
developing organization of this concern and provide that organization
with appropriate relevant information upon which it bases its concern;
3. UL must not engage in, or permit others to engage in, any
misrepresentation of the scope or conditions of its recognition. As
part of this condition, UL agrees that it will allow no representation
that it is either a recognized or an accredited NRTL without clearly
indicating the specific equipment or material to which this recognition
applies, and also clearly indicating that its recognition is limited to
specific products;
4. UL must inform OSHA as soon as possible, in writing, of any
change of ownership, facilities, or key personnel, and of any major
changes in its operations as an NRTL, including details of these
changes;
5. UL will meet all the terms of its recognition, and will always
comply with all OSHA policies pertaining to this recognition; and
6. UL will continue to meet the requirements for recognition in all
areas covered by its scope of recognition.
Issue Regarding NFPA Standards
In this notice, OSHA is modifying the scopes of recognition of
three NRTLs. Specifically, five standards that OSHA currently includes,
to varying degrees, in the scopes of recognition of these NRTLs are not
``appropriate test standards'' under 29 CFR 1910.7(c) because they do
not primarily cover product-safety testing. In addition, OSHA has no
requirement for NRTL approval of the systems covered by these
standards. Consequently, OSHA is removing the test standards from the
scopes of recognition of each affected NRTL (see list below).
OSHA specifies a scope of recognition for each NRTL that includes a
list of product-safety test standards that the NRTL may use in testing
and certifying (i.e., approving) products; NRTLs must demonstrate that
the products conform to ``appropriate test standards,'' as defined
under 29 CFR 1910.7(c). ``Appropriate test standards'' are consensus-
based product-safety test standards developed and maintained by U.S.-
based standards-developing organizations (SDOs). These test standards
are not OSHA standards, which are general requirements that employers
must meet; the test standards specify technical safety requirements
that particular types of products must meet.
The notice for the expansion described above also proposed the
removal of these five test standards from each affected NRTL's scope of
recognition. OSHA requested comments on the notice by May 11, 2010;
OSHA received no comments in response to this notice. OSHA now is
proceeding with this final notice modifying the scopes of recognition
of the affected NRTLs (see list below).
OSHA will incorporate the modifications specified by this notice on
its informational Web page for each affected NRTL. This page details
OSHA's official scope of recognition for the NRTL, including the
standards the NRTL may use to certify products under OSHA's NRTL
Program. Access to these Web pages is available through http://www.osha.gov/dts/otpca/nrtl/index.html.
Modification to Each NRTL's Scope of Recognition: \3\
---------------------------------------------------------------------------
\3\ For each test standard deleted, OSHA uses the name as it now
appears on OSHA's informational Web page for each NRTL. These names
may differ from the standard's current name (i.e., name as of the
date of this notice), which are as follows:
ANSI/NFPA 11 Low-, Medium-, and High-Expansion Foam
ANSI/NFPA 12 Carbon Dioxide Extinguishing Systems
ANSI/NFPA 12A Halon 1301 Fire Extinguishing Systems
ANSI/NFPA 16 Standard for the Installation of Foam-Water
Sprinkler and Foam-Water Spray Systems
ANSI/NFPA 17 Dry Chemical Extinguishing Systems
---------------------------------------------------------------------------
[[Page 77005]]
FM Approvals LLC (FM)
Deleted Test Standards:
ANSI 11 Low Expansion Foam and Combined Agent Systems
ANSI 12 Carbon Dioxide Extinguishing Systems
ANSI 12A Halon 1301 Fire Extinguishing Agent Systems
ANSI 16 Deluge Foam-Water Sprinkler and Spray Systems
ANSI 17 Dry Chemical Extinguishing Systems
Intertek Testing Services NA, Inc. (ITSNA)
Deleted Test Standards:
ANSI/NFPA 11 Low Expansion Foam and Combined Agent Systems
ANSI/NFPA 12 Carbon Dioxide Extinguishing Systems
ANSI/NFPA 12A Halon 1301 Fire Extinguishing Agent Systems
ANSI/NFPA 17 Dry Chemical Extinguishing Systems
Underwriters Laboratories Inc. (UL)
Deleted Test Standards:
ANSI/NFPA 11 Low Expansion Foam and Combined Agent Systems
ANSI/NFPA 12 Carbon Dioxide Extinguishing Systems
ANSI/NFPA 12A Halon 1301 Fire Extinguishing Agent Systems
ANSI/NFPA 17 Dry Chemical Extinguishing Systems
Authority and Signature
David Michaels, PhD, MPH, Assistant Secretary of Labor for
Occupational Safety and Health, 200 Constitution Avenue, NW.,
Washington, DC 20210, directed the preparation of this notice.
Accordingly, the Agency is issuing this notice pursuant to Sections
6(b) and 8(g) of the Occupational Safety and Health Act of 1970 (29
U.S.C. 655 and 657), Secretary of Labor's Order No. 4-2010 (75 FR
55355), and 29 CFR part 1911.
Signed at Washington, DC, on December 6, 2010.
David Michaels,
Assistant Secretary of Labor for Occupational Safety and Health.
[FR Doc. 2010-31048 Filed 12-9-10; 8:45 am]
BILLING CODE 4510-26-P