[Federal Register Volume 75, Number 75 (Tuesday, April 20, 2010)]
[Proposed Rules]
[Pages 20548-20550]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2010-9064]
=======================================================================
-----------------------------------------------------------------------
DEPARTMENT OF COMMERCE
National Oceanic and Atmospheric Administration
50 CFR Part 622
[Docket No. 100121040-0178-01]
RIN 0648-AY58
Fisheries of the Caribbean, Gulf of Mexico, and South Atlantic;
Shrimp Fishery of the Gulf of Mexico and South Atlantic; Revisions to
Allowable Bycatch Reduction Devices
AGENCY: National Marine Fisheries Service (NMFS), National Oceanic and
Atmospheric Administration (NOAA), Commerce.
ACTION: Proposed rule; request for comments.
-----------------------------------------------------------------------
SUMMARY: In accordance with the framework procedures for adjusting
management measures of the Fishery
[[Page 20549]]
Management Plan for the Shrimp Fishery of the Gulf of Mexico (Gulf FMP)
and the Fishery Management Plan for the Shrimp Fishery of the South
Atlantic region (South Atlantic FMP) NMFS proposes to provisionally
recertify two bycatch reduction devices (BRDs) and revise the
construction and installation requirements of one of these BRD designs
in the southeastern shrimp fishery. The intended effect of this
proposed rule is to improve bycatch reduction in the shrimp fishery,
reduce regulatory confusion, and better meet the requirements of
National Standard 9.
DATES: Comments must be received no later than 4:30 p.m., eastern time,
on May 5, 2010.
ADDRESSES: You may submit comments, identified by 0648-AY58, by any one
of the following methods:
Electronic Submissions: Submit all electronic public
comments via the Federal e-Rulemaking Portal http://www.regulations.gov.
Mail: Steve Branstetter, Southeast Regional Office, NMFS,
263 13th Avenue South, St. Petersburg, FL 33701.
Instructions: No comments will be posted for public viewing until
after the comment period has closed. All comments received are a part
of the public record and will generally be posted to http://www.regulations.gov without change. All Personal Identifying
Information (for example, name, address, etc.) voluntarily submitted by
the commenter may be publicly accessible. Do not submit Confidential
Business Information or otherwise sensitive or protected information.
To submit comments through the Federal e-Rulemaking Portal at
http://www.regulations.gov, enter ``NOAA-NMFS-2010-0020'' in the
keyword search, then select ``Send a Comment or Submission.'' NMFS will
accept anonymous comments. Attachments to electronic comments will be
accepted in Microsoft Word, Excel, Wordperfect, or Adobe PDF file
formats only.
Comments received through means not specified in this rule will not
be considered.
Copies of supporting documentation for this proposed rule, which
includes a regulatory impact review and a regulatory flexibility act
analysis, are available from NMFS at the address above.
FOR FURTHER INFORMATION CONTACT: Steve Branstetter, telephone: 727-824-
5305.
SUPPLEMENTARY INFORMATION: The fishery for shrimp in the exclusive
economic zone (EEZ) of the Gulf is managed under the FMP prepared by
the Gulf of Mexico Fishery Management Council. The fishery for shrimp
in the EEZ of the South Atlantic is managed under the FMP prepared by
the South Atlantic Fishery Management Council. The FMPs are implemented
under the authority of the Magnuson-Stevens Fishery Conservation and
Management Act (Magnuson-Stevens Act) by regulations at 50 CFR part
622.
Background
Regulations implementing Amendment 2 to the South Atlantic Shrimp
FMP (73 FR 18536, April 16, 1997) established BRD requirements in the
South Atlantic EEZ. The rule established a certification criterion,
descriptions of BRD designs and configurations allowed for use in the
South Atlantic shrimp fishery, as well as procedures to develop and
test new BRDs for certification.
Regulations implementing Amendment 9 to the Gulf Shrimp FMP were
published April 14, 1998 (63 FR 18139), and established a requirement,
with limited exceptions, for the use of certified BRDs in shrimp trawls
towed in the Gulf EEZ shoreward of the 100-fm (183-m) depth contour
west of 85 30' W. longitude (western Gulf), the approximate longitude
of Cape San Blas, FL. The rule established descriptions of BRD designs
and configurations allowed for use in the western Gulf shrimp fishery.
To better address the requirements of National Standard 9 of the
Magnuson-Stevens Act, regulations implementing Amendment 10 to the Gulf
FMP (69 FR 1538, January 9, 2004) required BRDs in shrimp trawls fished
in the EEZ east of 85 30' W. longitude (eastern Gulf).
In accordance with the BRD framework procedures of the Gulf FMP,
NMFS recently modified the existing BRD certification criterion for the
western Gulf (73 FR 8219, February 13, 2008) to be consistent with the
criterion for the eastern Gulf and South Atlantic. The new standardized
certification criterion for the Gulf of Mexico and the South Atlantic
specifies data must demonstrate a BRD achieves a 30-percent reduction
in the weight of finfish bycatch to be certified for use in the
southeastern shrimp fishery. In addition, this rule established a
provisional certification criterion. To be provisionally certified, on
a time-limited basis, the data must demonstrate that there is at least
a 50-percent probability that the BRD reduces the weight of finfish
bycatch by 25 percent.
In accordance with these new criteria, NMFS provisionally certified
the Extended Funnel BRD for use in the Gulf of Mexico, and the
Composite Panel BRD for use in both the Gulf of Mexico and the South
Atlantic. By regulation, the provisional certification of both BRDs
automatically expired on February 16, 2010. However, no new information
exists regarding the effectiveness of these BRDs as they are used in
the fishery that would indicate if the BRDs have been improved, or that
they do not continue to meet the provisional certification requirement.
Collection of new data and sufficient industry-level evaluation of
these BRDs was hindered, in part, because of delays in getting
compatible regulations allowing their use in state waters off Texas and
state waters off both the Gulf of Mexico and South Atlantic coasts of
Florida. Texas developed compatible regulations allowing the use of
these two BRDs in November 2008; Florida in December 2009. Thus,
fishermen in these states have not had the opportunity to use these new
BRDs or to make improvements to them. In addition, net shops that would
be manufacturing these BRDs needed to wait on the final regulatory
specifications before they could begin producing the BRDs, thus there
was an initial shortage of these BRDs.
Because no new information exists to decertify these BRDs, and
because of the limited time fishermen in two major shrimping states
have had to evaluate these BRDs, the proposed rule would reestablish a
new provisional certification for these two BRD types for two
additional years from the date of publication of the final rule in the
Federal Register. This proposed rule would also revise the construction
and installation requirements for the Composite Panel BRD in order to
provide more flexibility for what material and size mesh may be used to
construct this particular BRD design. The intended effect of this
proposed rule is to maintain adequate bycatch reduction in the shrimp
fishery, reduce regulatory confusion, and better meet the requirements
of National Standard 9.
Classification
Pursuant to section 304(b)(1)(A) of the Magnuson-Stevens Act, the
NMFS Assistant Administrator has determined that this proposed rule is
consistent with the FMP, other provisions of the Magnuson-Stevens Act,
and other applicable law, subject to further consideration after public
comment.
This proposed rule has been determined to be not significant for
purposes of Executive Order 12866.
The Chief Council for Regulation of the Department of Commerce
certified
[[Page 20550]]
to the Chief Council for Advocacy of the Small Business Administration
that this proposed rule, if adopted, would not have a significant
economic impact on a substantial number of small entities.
This proposed rule would not impose any new requirements on
fishing entities in the southeastern shrimp fishery. Shrimp trawlers
in the Gulf and South Atlantic EEZ are already required to have a
BRD installed in their shrimp nets and fishermen can continue to use
their existing BRD. This proposed rule would simply allow fishermen,
at their discretion, to use an alternative BRD in their shrimp nets,
and provide greater flexibility in the construction and installation
requirements for the Composite Panel BRD. Any decision to use this
gear would be expected to occur only if it is expected to result in
improved performance by the fishing vessel. As a result, any effects
would be expected to be positive and no adverse economic impacts on
any of the 2,144 vessels (which is the total number of unique
vessels with a permit to harvest shrimp in the EEZ of the Gulf and
South Atlantic) would be expected to accrue. Providing greater
flexibility in the construction and installation requirements for
the Composite Panel BRD is also expected to lower costs and result
in no additional adverse economic impacts.
As a result, an initial regulatory flexibility analysis is not
required and none has been prepared.
List of Subjects in 50 CFR Part 622
Fisheries, Fishing, Puerto Rico, Reporting and recordkeeping
requirements, Virgin Islands.
Dated: April 15, 2010.
Samuel D. Rauch III,
Deputy Assistant Administrator For Regulatory Programs, National Marine
Fisheries Service.
For the reasons set out in the preamble, 50 CFR part 622 is
proposed to be amended as follows:
PART 622--FISHERIES OF THE CARIBBEAN, GULF, AND SOUTH ATLANTIC
1. The authority citation for part 622 continues to read as
follows:
Authority: 16 U.S.C. 1801 et seq.
2. In Sec. 622.41, paragraphs (g)(3)(ii)(A) and (B) are revised to
read as follows:
Sec. 622.41 Species specific limitations.
* * * * *
(g) * * *
(3) * * *
(ii) * * *
(A) Extended funnel--Gulf EEZ only; through [date 2 years after
date of publication of the final rule in the Federal Register].
(B) Composite Panel--Gulf EEZ and South Atlantic EEZ; through [date
2 years after date of publication of the final rule in the Federal
Register].
* * * * *
3. In Appendix D to part 622, section G, the first sentence of
paragraph 2(a), and paragraph 2(b) are revised to read as follows:
Appendix D to Part 622--Specifications for Certified BRDs
* * * * *
G. * * *
2. * * *
(a) * * * The webbing extension must be constructed from a
single rectangular piece of 1 \1/2\-inch to 1 \3/4\-inch (3.8-cm to
4.5-cm) stretch mesh with dimensions of 24 1/2 meshes by 150 to 160
meshes. * * *
(b) Funnel. The V-shaped funnel consists of two webbing panels
attached to the extension along the leading edge of the panels. The
top and bottom edges of the panels are sewn diagonally across the
extension toward the center to form the funnel. The panels are 2-ply
in design, each with an inner layer of 1 \1/2\-inch to 1 \5/8\-inch
(3.8-cm to 4.1-cm) heat-set and depth-stretched polyethylene webbing
and an outer layer constructed of no larger than 2-inch (5.1-cm)
square mesh webbing (1-inch bar). The inner webbing layer must be
rectangular in shape, 36 meshes on the leading edge by 20 meshes
deep. The 36-mesh leading edges of the polyethylene webbing should
be sewn evenly to 24 meshes of the extension webbing 1 \1/2\ meshes
from and parallel to the leading edge of the extension starting 12
meshes up from the bottom center on each side. Alternately sew 2
meshes of the polyethylene webbing to 1 mesh of the extension
webbing then 1 mesh of the polyethylene webbing to 1 mesh of the
extension webbing toward the top. The bottom 20-mesh edges of the
polyethylene layers are sewn evenly to the extension webbing on a 2
bar 1 mesh angle toward the bottom back center forming a v-shape in
the bottom of the extension webbing. The top 20-mesh edges of the
polyethylene layers are sewn evenly along the bars of the extension
webbing toward the top back center. The square mesh layers must be
rectangular in shape and constructed of no larger than 2-inch (5.1-
cm) webbing that is 18 inches (45.7 cm) in length on the leading
edge. The depth of the square mesh layer must be no more than 2
inches (5.1 cm) less than the 20 mesh side of the inner polyethylene
layer when stretched taught. The 18-inch (45.7-cm) leading edge of
each square mesh layer must be sewn evenly to the 36-mesh leading
edge of the polyethylene section and the sides are sewn evenly (in
length) to the 20-mesh edges of the polyethylene webbing. This will
form a v-shape funnel using the top of the extension webbing as the
top of the funnel and the bottom of the extension webbing as the
bottom of the funnel.
* * * * *
[FR Doc. 2010-9064 Filed 4-19-10; 8:45 am]
BILLING CODE 3510-22-S