[Federal Register Volume 76, Number 25 (Monday, February 7, 2011)]
[Rules and Regulations]
[Pages 6525-6529]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2011-2008]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2009-1186; Directorate Identifier 2009-CE-065-AD;
Amendment 39-16588; AD 2011-03-04]
RIN 2120-AA64
Airworthiness Directives; Cessna Aircraft Company (Type
Certificate Previously Held by Columbia Aircraft Manufacturing
(Previously the Lancair Company)) Models LC40-550FG, LC41-550FG, and
LC42-550FG Airplanes
AGENCY: Federal Aviation Administration (FAA), DOT.
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: We are superseding an existing airworthiness directive (AD)
for the products listed above. AD 2009-09-09 currently requires
repetitive inspections of the rudder hinges and the rudder hinge
brackets for damage, i.e., cracking, deformation, and discoloration. If
damage is found during any inspection, AD 2009-09-09 also requires
replacing the damaged rudder hinge and/or rudder hinge bracket. This
new AD retains the inspection requirements of AD 2009-09-09, adds
airplanes to the Applicability section, and adds a terminating action
for the repetitive inspection requirements. This AD resulted from the
manufacturer developing a modification that terminates the repetitive
inspections and from the manufacture adding airplane serial numbers
into the Applicability section. We are issuing this AD to detect and
correct damage in the rudder hinges and the rudder hinge brackets,
which could result in failure of the rudder. This failure could lead to
loss of control.
DATES: This AD is effective March 14, 2011.
The Director of the Federal Register approved the incorporation by
reference of certain publications listed in the AD as of March 14,
2011.
The Director of the Federal Register approved the incorporation by
reference of a certain publication listed in this AD as of May 11, 2009
(74 FR 19873, April 30, 2009).
ADDRESSES: For service information identified in this AD, contact
Cessna Aircraft Company, Product Support, P.O. Box 7706; Wichita,
Kansas 67277; telephone: (316) 517-5800; fax: (316) 942-9006; Internet:
http://www.cessna.com. You may review copies of the referenced service
information at the FAA, Small Airplane Directorate, 901 Locust, Kansas
City, Missouri 64106. For information on the availability of this
material at the FAA, call (816) 329-4148.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Management Facility
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains this AD, the regulatory evaluation,
any comments received, and other information. The address for the
Docket Office (phone: 800-647-5527) is Document Management Facility,
U.S. Department of Transportation, Docket Operations, M-30, West
Building Ground Floor, Room W12-140, 1200
[[Page 6526]]
New Jersey Avenue SE., Washington, DC 20590.
FOR FURTHER INFORMATION CONTACT: Gary Park, Aerospace Engineer, Wichita
Aircraft Certification Office, FAA, 1801 Airport Road, Room 100,
Wichita, Kansas 67209; telephone: (316) 946-4123; fax: (316) 946-4107;
e-mail: [email protected].
SUPPLEMENTARY INFORMATION:
Discussion
We issued a supplemental notice of proposed rulemaking (SNPRM) to
amend 14 CFR part 39 to supersede AD 2009-09-09, Amendment 39-15895 (74
FR 19873, April 30, 2009). That AD applies to the specified products.
The SNPRM published in the Federal Register on October 27, 2010 (75 FR
66009). That SNPRM proposed to retain the inspection requirements of AD
2009-09-09, add airplanes to the Applicability section, and add a
terminating action for the repetitive inspection requirements using
revised service information.
Comments
We gave the public the opportunity to participate in developing
this AD. We received no comments on the SNPRM or on the determination
of the cost to the public.
Conclusion
We reviewed the relevant data and determined that air safety and
the public interest require adopting the AD as proposed except for
minor editorial changes. We have determined that these minor changes:
Are consistent with the intent that was proposed in the
SNPRM for correcting the unsafe condition; and
Do not add any additional burden upon the public than was
already proposed in the SNPRM.
Costs of Compliance
We estimate that this proposed AD affects 790 airplanes of U.S.
registry.
We estimate the following costs to comply with this AD:
Estimated Costs
--------------------------------------------------------------------------------------------------------------------------------------------------------
Action Labor cost Parts cost Cost per product Cost on U.S. operators
--------------------------------------------------------------------------------------------------------------------------------------------------------
Inspecting the rudder hinges and 1.5 work-hours x $85 per Not applicable........ $127.50 per $72,675 per inspection cycle.
rudder hinge brackets for damage hour = $127.50 per inspection cycle.
with rudder removed (affects 570 inspection cycle.
airplanes).
Inspecting the rudder hinges and .5 work-hour x $85 per hour Not applicable........ $42.50 per inspection $24,225 per inspection cycle.
rudder hinge brackets for damage = $42.50 per inspection cycle.
without rudder removed (affects cycle.
570 airplanes).
Incorporating the modification kit 1 work-hour x $85 per hour $739.................. $824................. $203,528.
for Models LC40-550FG and LC42- = $85.
550FG airplanes (affects 247
airplanes).
Incorporating the modification kit 1 work-hour x $85 per hour $848.................. $933................. $487,959.
for Model LC41-550FG airplanes = $85.
(affects 523 airplanes).
Inspecting the rudder hinge and the .5 work-hour x $85 per hour Not applicable........ $42.50............... $850.
rudder brackets attachment = $42.50.
hardware for correct thread
engagement (affects 20 airplanes).
Inspecting the rudder travel 1 work-hour x $85 per hour Not applicable........ $85.................. $1,700.
(affects 20 airplanes). = $85.
--------------------------------------------------------------------------------------------------------------------------------------------------------
We estimate the following costs to do any necessary repairs that
will be required based on the results of the inspection of the rudder
hinge and the rudder brackets attachment hardware for correct thread
engagement and the rudder travel. We have no way of determining the
number of aircraft that might need these repairs:
On-Condition Costs
----------------------------------------------------------------------------------------------------------------
Cost per
Action Labor cost Parts cost product
----------------------------------------------------------------------------------------------------------------
Repair the rudder hinge and the rudder .5 work-hour x $85 per hour = $14 $56.50
brackets attachment hardware thread $42.50.
engagement (could affect 20 airplanes).
Repair the rudder travel (could affect 20 .5 work-hour x $85 per hour = 14 56.50
airplanes). $42.50.
----------------------------------------------------------------------------------------------------------------
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, Section 106, describes the
authority of the FAA Administrator. Subtitle VII, Aviation Programs,
describes in more detail the scope of the Agency's authority.
We are issuing this rulemaking under the authority described in
Subtitle VII, Part A, Subpart III, Section 44701, ``General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
[[Page 6527]]
Regulatory Findings
We have determined that this AD will not have federalism
implications under Executive Order 13132. This AD will not have a
substantial direct effect on the States, on the relationship between
the national government and the States, or on the distribution of power
and responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866,
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979),
(3) Will not affect intrastate aviation in Alaska, and
(4) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
Accordingly, under the authority delegated to me by the
Administrator, the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by removing Airworthiness Directive (AD)
2009-09-09, Amendment 39-15895 (74 FR 19873, April 30, 2009), and
adding the following new AD:
2011-03-04 Cessna Aircraft Company (Type Certificate Previously Held
by Columbia Aircraft Manufacturing (Previously The Lancair
Company)): Amendment 39-16588; Docket No. FAA-2009-1186; Directorate
Identifier 2009-CE-065-AD.
Effective Date
(a) This airworthiness directive (AD) is effective March 14,
2011.
Affected ADs
(b) This AD supersedes AD 2009-09-09, Amendment 39-15895.
Applicability
(c) This AD applies to the following Cessna Aircraft Company
(type certificate previously held by Columbia Aircraft Manufacturing
(previously The Lancair Company)) airplane models and serial numbers
that are certificated in any category:
Group 1 Airplanes
------------------------------------------------------------------------
Model Serial Nos.
------------------------------------------------------------------------
LC40-550FG (300).................. 40001, 40002, and 40004 through
40079.
LC41-550FG (400).................. 41001 through 41569, 41571 through
41800, 411001 through 411087,
411089 through 411110, 411112
through 411138, 411140, 411142, and
411147.
LC42-550FG (350).................. 42001 through 42009, 42011 through
42558, 42560 through 42569, 421001
through 421013, 421015 through
421017, and 421019.
------------------------------------------------------------------------
Group 2 Airplanes
------------------------------------------------------------------------
Model Serial Nos.
------------------------------------------------------------------------
LC41-550FG (400).................. 41570, 411088, 411111, 411139,
411141, 411143 through 411146, and
411148 through 411153.
LC42-550FG (350).................. 42010, 42559, 421014, 421018, and
421020.
------------------------------------------------------------------------
Subject
(d) Joint Aircraft System Component (JASC)/Air Transport
Association (ATA) of America Code 55, Stabilizers.
Unsafe Condition
(e) This AD is the result of reports received of a cracked lower
rudder hinge bracket on two of the affected airplanes. We are
issuing this AD to detect and correct damage, i.e., cracking,
deformation, and discoloration, in the rudder hinges and the rudder
hinge brackets, which could result in failure of the rudder. This
failure could lead to loss of control.
Compliance
(f) To address this problem, you must do the following, unless
already done:
(1) For Group 1 airplanes specified in paragraph (c) of this AD:
Using the compliance times specified in table 1 of this AD, inspect
the rudder hinges and rudder hinge brackets for damage, i.e.,
cracking, deformation, and discoloration. Do the inspections
following Cessna Single Engine Service Bulletin SB09-27-01, dated
April 13, 2009; Cessna Single Engine Service Bulletin SB09-27-01,
Revision 2, dated November 23, 2009; or Cessna Single Engine Service
Bulletin SB09-27-01, Revision 3, dated July 20, 2010.
[[Page 6528]]
Table 1--Inspection Compliance Times
------------------------------------------------------------------------
Initially inspect . Repetitively inspect
Condition . . . . .
------------------------------------------------------------------------
(i) For airplanes with 25 With the rudder Thereafter inspect
hours time-in-service (TIS) removed and using as follows until
or more as of May 11, 2009 10X visual the modification
(the effective date of AD magnification, required in
2009-09-09). inspect all three paragraph (f)(5) of
rudder hinges and this AD is done:
rudder hinge (A) Every 25 hours
brackets at TIS or 3 months,
whichever of the whichever occurs
following occurs first, without
first removing the
(A) Within the next rudder, visually
10 hours TIS after inspect all three
May 11, 2009 (the rudder hinges and
effective date of rudder hinge
AD 2009-09-09); or. brackets; and
(B) Within the next (B) Every 50 hours
30 days after May TIS or 6 months,
11, 2009 (the whichever occurs
effective date of first, with the
AD 009-09-09). rudder removed and
using 10X visual
magnification,
inspect all three
rudder hinges and
rudder hinge
brackets.
(ii) For airplanes with less Without removing the Thereafter inspect
than 25 hours TIS as of May rudder, visually as follows until
11, 2009 (the effective inspect all three the modification
date of AD 2009-09-09). rudder hinges and required in
rudder hinge paragraph (f)(5) of
brackets, at this AD is done:
whichever of the (A) Every 25 hours
following occurs TIS or 3 months,
later. whichever occurs
(A) Upon first, without
accumulating 25 removing the
hours TIS; or. rudder, visually
(B) Within the next inspect all three
10 hours TIS after rudder hinges and
May 11, 2009 (the rudder hinge
effective date of brackets; and
AD 2009-09-09). (B) Every 50 hours
TIS or 6 months,
whichever occurs
first, with the
rudder removed and
using 10X visual
magnification,
inspect all three
rudder hinges and
rudder hinge
brackets.
------------------------------------------------------------------------
(2) For Group 1 airplanes specified in paragraph (c) of this
AD: Before further flight after any inspection required in
paragraphs (f)(1)(i) or (f)(1)(ii) of this AD in which damage is
found on any of the rudder hinges and/or rudder hinge brackets,
incorporate Cessna Single Engine Modification Kit MK400-27-01, dated
November 23, 2009; or Cessna Single Engine Modification Kit MK400-
27-01A dated July 20, 2010, as specified in Cessna Single Engine
Service Bulletin SB09-27-01, Revision 2, dated November 23, 2009;
and Cessna Single Engine Service Bulletin SB09-27-01, Revision 3,
dated July 20, 2010. Incorporating either Modification Kit MK400-27-
01 or Modification Kit MK400-27-01A, terminates the repetitive
inspections required in paragraphs (f)(1)(i) and (f)(1)(ii) of this
AD.
(3) For Group 1 airplanes specified in paragraph (c) of this AD:
If the repetitive inspections required in paragraphs (f)(1)(i) and
(f)(1)(ii) of this AD become due at the same time, credit for both
inspections will be given by doing the rudder removal and 10X visual
inspection.
(4) For Group 1 airplanes specified in paragraph (c) of this AD:
Within the next 24 months after March 14, 2011 (the effective date
of this AD), incorporate Cessna Single Engine Modification Kit
MK400-27-01, dated November 23, 2009; or Cessna Single Engine
Modification Kit MK400-27-01A, dated July 20, 2010, as specified in
Cessna Single Engine Service Bulletin SB09-27-01, Revision 2, dated
November 23, 2009; and Cessna Single Engine Service Bulletin SB09-
27-01, Revision 3, dated July 20, 2010, unless already done as
specified in paragraph (f)(2) of this AD. Incorporating either
Modification Kit MK400-27-01 or Modification Kit MK400-27-01A,
terminates the repetitive inspections required in paragraphs
(f)(1)(i) and (f)(1)(ii) of this AD.
(5) For Group 1 airplanes specified in paragraph (c) of this AD:
At any time after the initial inspections required in paragraphs
(f)(1)(i) and (f)(1)(ii) of this AD, as long as no damage is found,
and no later than the compliance time specified in paragraph (f)(4)
of this AD, you may incorporate Cessna Single Engine Modification
Kit MK400-27-01, dated November 23, 2009; or Cessna Single Engine
Modification Kit MK400-27-01A, dated July 20, 2010, as specified in
Cessna Single Engine Service Bulletin SB09-27-01, Revision 2, dated
November 23, 2009; and Cessna Single Engine Service Bulletin SB09-
27-01, Revision 3, dated July 20, 2010, to terminate the repetitive
inspections required in paragraphs (f)(1)(i) and (f)(1)(ii) of this
AD.
(6) For any Group 1 airplane with Cessna Single Engine Service
Bulletin SB09-27-01, Revision 1, dated August 31, 2009, already
incorporated and for all Group 2 airplanes: Within the next 30 days
after March 14, 2011 (the effective date of this AD), inspect for
proper rudder hinge and rudder bracket hardware thread engagement
and inspect the rudder travel. Do these inspections following the
Accomplishment Instructions in Cessna Single Engine Modification Kit
MK400-27-01, dated November 23, 2009; or the Accomplishment
Instructions in Cessna Single Engine Modification Kit MK400-27-01A,
dated July 20, 2010.
(i) Before further flight after the inspection required in
paragraph (f)(6) of this AD, if any discrepancies are found in the
rudder hinge or rudder bracket hardware, replace the affected
hardware. Do the replacements following the Accomplishment
Instructions in Cessna Single Engine Modification Kit MK400-27-01,
dated November 23, 2009; or the Accomplishment Instructions in
Cessna Single Engine Modification Kit MK400-27-01A, dated July 20,
2010.
(ii) Before further flight after the inspection required in
paragraph (f)(6) of this AD, if the rudder travel is outside the
limits specified in the Accomplishment Instructions in Cessna Single
Engine Modification Kit MK400-27-01, dated November 23, 2009; or the
Accomplishment Instructions in Cessna Single Engine Modification Kit
MK400-27-01A, dated July 20, 2010, reinstall the rudder following
the Accomplishment Instructions in either Cessna Single Engine
Modification Kit MK400-27-01, dated November 23, 2009; or Cessna
Single Engine Modification Kit MK400-27-01A, dated July 20, 2010.
(iii) After the inspection and any necessary corrective actions
required in paragraphs (f)(6), (f)(6)(i), and (f)(6)(ii) of this AD,
no further action is required.
Credit for Actions Accomplished in Accordance With Previous Service
Information
(g) For all airplanes specified in paragraph (c) of this AD: As
of March 14, 2011 (the effective date of this AD), if Cessna Single
Engine Service Bulletin SB09-27-01, Revision 2, dated November 23,
2009, has already been incorporated, no further action is required.
Alternative Methods of Compliance (AMOCs)
(h)(1) The Manager, Wichita Aircraft Certification Office (ACO),
FAA, has the authority to approve AMOCs for this AD, if requested
using the procedures found in 14 CFR 39.19. In accordance with 14
CFR 39.19, send your request to your principal inspector or local
Flight Standards District Office, as appropriate. If sending
information directly to the manager of the ACO, send it to the
attention of the person identified in the Related Information
section of this AD.
(2) Before using any approved AMOC, notify your Principal
Maintenance Inspector or Principal Avionics Inspector, as
appropriate, or lacking a principal inspector, your local Flight
Standards District Office.
(3) AMOCs approved for AD 2009-09-09 are approved for this AD.
Related Information
(i) For more information about this AD, contact Gary Park,
Aerospace Engineer, Wichita ACO, FAA, 1801 Airport Road, Room 100,
Wichita, Kansas 67209; telephone: (316) 946-4123; fax: (316) 946-
4107; e-mail: [email protected].
Material Incorporated by Reference
(j) You must use Cessna Single Engine Service Bulletin SB09-27-
01, dated April 13, 2009; Cessna Single Engine Service Bulletin
SB09-27-01, Revision 2, dated November 23, 2009; Cessna Single
Engine Service Bulletin SB09-27-01, Revision 3, dated July 20, 2010;
[[Page 6529]]
Cessna Single Engine Modification Kit MK400-27-01, dated November
23, 2009; and Cessna Single Engine Modification Kit MK400-27-01A,
dated July 20, 2010, to do the actions required by this AD, unless
the AD specifies otherwise.
(1) The Director of the Federal Register approved the
incorporation by reference of Cessna Single Engine Service Bulletin
SB09-27-01, Revision 2, dated November 23, 2009; and Cessna Single
Engine Service Bulletin SB09-27-01, Revision 3, dated July 20, 2010;
Cessna Single Engine Modification Kit MK400-27-01, dated November
23, 2009; and Cessna Single Engine Modification Kit MK400-27-01A,
dated July 20, 2010, under 5 U.S.C. 552(a) and 1 CFR part 51.
(2) The Director of the Federal Register previously approved the
incorporation by reference of Cessna Single Engine Service Bulletin
SB09-27-01, dated April 13, 2009, on May 11, 2009 (74 FR 19873,
April 30, 2009).
(3) For service information identified in this AD, contact
Cessna Aircraft Company, Product Support, P.O. Box 7706; Wichita,
Kansas 67277; telephone: (316) 517-5800; fax: (316) 942-9006;
Internet: http://www.cessna.com.
(4) You may review copies of the service information at the FAA,
Small Airplane Directorate, 901 Locust, Kansas City, Missouri 64106.
For information on the availability of this material at the FAA,
call 816-329-4148.
(5) You may also review copies of the service information that
is incorporated by reference at the National Archives and Records
Administration (NARA). For information on the availability of this
material at an NARA facility, call 202-741-6030, or go to http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.
Issued in Kansas City, Missouri, on January 25, 2011.
John Colomy,
Acting Manager, Small Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 2011-2008 Filed 2-4-11; 8:45 am]
BILLING CODE 4910-13-P