[Federal Register Volume 76, Number 8 (Wednesday, January 12, 2011)]
[Rules and Regulations]
[Pages 1985-1990]
From the Federal Register Online via the Government Publishing Office [www.gpo.gov]
[FR Doc No: 2011-30]
-----------------------------------------------------------------------
DEPARTMENT OF TRANSPORTATION
Federal Aviation Administration
14 CFR Part 39
[Docket No. FAA-2010-0225; Directorate Identifier 2009-NM-203-AD;
Amendment 39-16525; AD 2010-24-06]
RIN 2120-AA64
Airworthiness Directives; Short Brothers PLC Model SD3 Airplanes
AGENCY: Federal Aviation Administration (FAA), Department of
Transportation (DOT).
ACTION: Final rule.
-----------------------------------------------------------------------
SUMMARY: We are superseding an existing airworthiness directive (AD)
that applies to the products listed above. This AD results from
mandatory continuing airworthiness information (MCAI) issued by an
airworthiness authority of another country to identify and correct an
unsafe condition on an aviation product. The MCAI describes the unsafe
condition as
Subsequent to accidents involving Fuel Tank System explosions in
flight * * * and on ground, * * * Special Federal Aviation
Regulation 88 (SFAR88) * * * required a safety review of the
aircraft Fuel Tank System * * *.
* * * * *
Fuel Airworthiness Limitations are items arising from a systems
safety analysis that have been shown to have failure mode(s)
associated with an `unsafe condition' * * *. These are identified in
Failure Conditions for which an unacceptable probability of ignition
risk could exist if specific tasks and/or practices are not
performed in accordance with the manufacturers' requirements.
* * * * *
We are issuing this AD to require actions to correct the unsafe
condition on these products.
DATES: This AD becomes effective February 16, 2011.
The Director of the Federal Register approved the incorporation by
reference of certain publications listed in the AD as of February 16,
2011.
The Director of the Federal Register approved the incorporation by
reference of certain other publications listed in this AD as of July
21, 2006 (71 FR 34801, June 16, 2006).
ADDRESSES: You may examine the AD docket on the Internet at http://www.regulations.gov or in person at the U.S. Department of
Transportation, Docket Operations, M-30, West Building Ground Floor,
Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC.
FOR FURTHER INFORMATION CONTACT: Todd Thompson, Aerospace Engineer,
International Branch, ANM-116, Transport Airplane Directorate, FAA,
1601 Lind Avenue, SW., Renton, Washington 98057-3356; telephone (425)
227-1175; fax (425) 227-1149.
SUPPLEMENTARY INFORMATION:
Discussion
We issued a supplemental notice of proposed rulemaking (NPRM) to
amend 14 CFR part 39 to include an AD that would apply to the specified
products. That supplemental NPRM was published in the Federal Register
on August 4, 2010 (75 FR 46864), and proposed to supersede AD 2006-12-
18, Amendment 39-14644 (71 FR 34801, June 16, 2006). That NPRM proposed
to require revising the airplane flight manual (AFM); revising the
Airworthiness Limitation (AWL) section; doing a resistance check,
inspection, and jumper installation; and revising the AWL section. The
MCAI states:
[[Page 1986]]
Subsequent to accidents involving Fuel Tank System explosions in
flight * * * and on ground, the FAA published Special Federal
Aviation Regulation 88 (SFAR88) in June 2001. SFAR 88 required a
safety review of the aircraft Fuel Tank System to determine that the
design meets the requirements of FAR [Federal Aviation Regulation]
Sec. 25.901 and Sec. 25.981(a) and (b).
A similar regulation has been recommended by the JAA [Joint
Aviation Authorities] to the European National Aviation Authorities
in JAA letter 04/00/02/07/03-L024 of 3 February 2003. The review was
requested to be mandated by NAA's [National Airworthiness
Authorities] using JAR [Joint Aviation Requirement] Sec. 25.901(c),
Sec. 25.1309.
In August 2005 EASA [European Aviation Safety Agency] published
a policy statement on the process for developing instructions for
maintenance and inspection of Fuel Tank System ignition source
prevention (EASA D 2005/CPRO, www.easa.eu.int/home/cert_policy_statements_en.html) that also included the EASA expectations with
regard to compliance times of the corrective actions on the unsafe
and the not unsafe part of the harmonised design review results. On
a global scale the TC [type certificate] holders committed
themselves to the EASA published compliance dates (see EASA policy
statement). The EASA policy statement has been revised in March
2006: The date of 31-12-2005 for the unsafe related actions has now
been set at 01-07-2006.
Fuel Airworthiness Limitations are items arising from a systems
safety analysis that have been shown to have failure mode(s)
associated with an `unsafe condition' as defined in FAA's memo 2003-
112-15 `SFAR 88--Mandatory Action Decision Criteria'. These are
identified in Failure Conditions for which an unacceptable
probability of ignition risk could exist if specific tasks and/or
practices are not performed in accordance with the manufacturers'
requirements.
This EASA Airworthiness Directive mandates the Fuel System
Airworthiness Limitations, comprising maintenance/inspection tasks
and Critical Design Control Configuration Limitations (CDCCL) for
the type of aircraft, that resulted from the design reviews and the
JAA recommendation and EASA policy statement mentioned above.
Revision History: PAD [proposed airworthiness directive] 06-
018R1 has been issued to endorse comments received for PAD 06-018
and due to the change of the EASA policy statement on fuel tank
safety on March 2006.
You may obtain further information by examining the MCAI in the AD
docket.
Comments
We gave the public the opportunity to participate in developing
this AD. We received no comments on the NPRM or on the determination of
the cost to the public.
Explanation of Changes to This AD
We have revised Table 1 of this AD to indicate the appropriate AFM
for the identified airplane models. We have also added new paragraph
(l) to this AD (and have reidentified subsequent paragraphs
accordingly) to give credit to operators that might have included
Shorts Advance Amendment Bulletin 1/2004, dated 7/13/04, into the
incorrect AFM before the effective date of this AD. We have determined
that the content of Shorts Advance Amendment Bulletin 1/2004 to AFM
SB.5.2 and Shorts Advance Amendment Bulletin 1/2004 to AFM SB.6.2 is
identical, except for the AFM number shown on the top of the document
pages. Therefore, if an operator inserted the advance amendment
bulletin intended for AFM SB.5.2 into AFM SB.6.2 or vise versa, before
the effective date of this AD, the intent of the AFM revision required
by paragraph (g) of this AD has been met, and is, therefore, acceptable
for compliance with that requirement.
Conclusion
We reviewed the available data and determined that air safety and
the public interest require adopting the AD with the changes described
previously. We determined that these changes will not increase the
economic burden on any operator or increase the scope of the AD.
Differences Between This AD and the MCAI or Service Information
We have reviewed the MCAI and related service information and, in
general, agree with their substance. But we might have found it
necessary to use different words from those in the MCAI to ensure the
AD is clear for U.S. operators and is enforceable in a U.S. court of
law. In making these changes, we do not intend to differ substantively
from the information provided in the MCAI and related service
information. We might also have required different actions in this AD
from those in the MCAI in order to follow our FAA policies. Any such
differences are described in a separate paragraph of the AD. These
requirements, if any, take precedence over the actions copied from the
MCAI.
Costs of Compliance
We estimate that this AD will affect 54 products of U.S. registry.
The actions that are required by AD 2006-12-18 and retained in this
AD take about 41 work-hours per product, at an average labor rate of
$85 per work hour. Required parts cost about $10 per product. Based on
these figures, the estimated cost of the currently required actions is
$3,495 per product.
We estimate that it would take about 1 work-hour per product to
comply with the new basic requirements of this AD. The average labor
rate is $85 per work-hour. Based on these figures, we estimate the cost
of the AD on U.S. operators to be $4,590, or $85 per product.
Authority for This Rulemaking
Title 49 of the United States Code specifies the FAA's authority to
issue rules on aviation safety. Subtitle I, section 106, describes the
authority of the FAA Administrator. ``Subtitle VII: Aviation
Programs,'' describes in more detail the scope of the Agency's
authority.
We are issuing this rulemaking under the authority described in
``Subtitle VII, Part A, Subpart III, Section 44701: General
requirements.'' Under that section, Congress charges the FAA with
promoting safe flight of civil aircraft in air commerce by prescribing
regulations for practices, methods, and procedures the Administrator
finds necessary for safety in air commerce. This regulation is within
the scope of that authority because it addresses an unsafe condition
that is likely to exist or develop on products identified in this
rulemaking action.
Regulatory Findings
We determined that this AD will not have federalism implications
under Executive Order 13132. This AD will not have a substantial direct
effect on the States, on the relationship between the national
government and the States, or on the distribution of power and
responsibilities among the various levels of government.
For the reasons discussed above, I certify that this AD:
(1) Is not a ``significant regulatory action'' under Executive
Order 12866;
(2) Is not a ``significant rule'' under DOT Regulatory Policies and
Procedures (44 FR 11034, February 26, 1979); and
(3) Will not have a significant economic impact, positive or
negative, on a substantial number of small entities under the criteria
of the Regulatory Flexibility Act.
We prepared a regulatory evaluation of the estimated costs to
comply with this AD and placed it in the AD Docket.
Examining the AD Docket
You may examine the AD docket on the Internet at http://www.regulations.gov; or in person at the Docket Operations office
between 9 a.m. and 5 p.m., Monday through Friday, except Federal
holidays. The AD docket contains the NPRM, the regulatory evaluation,
any comments received, and other information. The street address for
the Docket Operations office (telephone
[[Page 1987]]
(800) 647-5527) is in the ADDRESSES section. Comments will be available
in the AD docket shortly after receipt.
List of Subjects in 14 CFR Part 39
Air transportation, Aircraft, Aviation safety, Incorporation by
reference, Safety.
Adoption of the Amendment
0
Accordingly, under the authority delegated to me by the Administrator,
the FAA amends 14 CFR part 39 as follows:
PART 39--AIRWORTHINESS DIRECTIVES
0
1. The authority citation for part 39 continues to read as follows:
Authority: 49 U.S.C. 106(g), 40113, 44701.
Sec. 39.13 [Amended]
0
2. The FAA amends Sec. 39.13 by removing Amendment 39-14644 (71 FR
34801, June 16, 2006) and adding the following new AD:
2010-24-06 Short Brothers PLC: Amendment 39-16525. Docket No. FAA-
2010-0225; Directorate Identifier 2009-NM-203-AD.
Effective Date
(a) This airworthiness directive (AD) becomes effective February
16, 2011.
Affected ADs
(b) This AD supersedes AD 2006-12-18, Amendment 39-14644.
Applicability
(c) This AD applies to all Short Brothers PLC Model SD3-60
SHERPA, SD3-SHERPA, SD3-30, and SD3-60 airplanes, certificated in
any category.
Note 1: This AD requires revisions to certain operator
maintenance documents to include new inspections. Compliance with
these inspections is required by 14 CFR 91.403(c). For airplanes
that have been previously modified, altered, or repaired in the
areas addressed by these inspections, the operator may not be able
to accomplish the inspections described in the revisions. In this
situation, to comply with 14 CFR 91.403(c), the operator must
request approval for an alternative method of compliance according
to paragraph (m) of this AD. The request should include a
description of changes to the required inspections that will ensure
the continued damage tolerance of the affected structure. The FAA
has provided guidance for this determination in Advisory Circular
(AC) 25-1529.
Subject
(d) Air Transport Association (ATA) of America Code 28: Fuel.
Reason
(e) The mandatory continuing airworthiness information (MCAI)
states:
Subsequent to accidents involving Fuel Tank System explosions in
flight * * * and on ground, the FAA published Special Federal
Aviation Regulation 88 (SFAR88) in June 2001. SFAR 88 required a
safety review of the aircraft Fuel Tank System to determine that the
design meets the requirements of FAR [Federal Aviation Regulation]
Sec. 25.901 and Sec. 25.981(a) and (b).
A similar regulation has been recommended by the JAA [Joint
Aviation Authorities] to the European National Aviation Authorities
in JAA letter 04/00/02/07/03-L024 of 3 February 2003. The review was
requested to be mandated by NAA's [National Airworthiness
Authorities] using JAR [Joint Aviation Requirement] Sec. 25.901(c),
Sec. 25.1309.
In August 2005 EASA [European Aviation Safety Agency] published
a policy statement on the process for developing instructions for
maintenance and inspection of Fuel Tank System ignition source
prevention (EASA D 2005/CPRO, http://www.easa.eu.int/home/cert_policy_statements_en.html) that also included the EASA
expectations with regard to compliance times of the corrective
actions on the unsafe and the not unsafe part of the harmonised
design review results. On a global scale the TC [type certificate]
holders committed themselves to the EASA published compliance dates
(see EASA policy statement). The EASA policy statement has been
revised in March 2006: The date of 31-12-2005 for the unsafe related
actions has now been set at 01-07-2006.
Fuel Airworthiness Limitations are items arising from a systems
safety analysis that have been shown to have failure mode(s)
associated with an `unsafe condition' as defined in FAA's memo 2003-
112-15 `SFAR 88--Mandatory Action Decision Criteria'. These are
identified in Failure Conditions for which an unacceptable
probability of ignition risk could exist if specific tasks and/or
practices are not performed in accordance with the manufacturers'
requirements.
This EASA Airworthiness Directive mandates the Fuel System
Airworthiness Limitations, comprising maintenance/inspection tasks
and Critical Design Control Configuration Limitations (CDCCL) for
the type of aircraft, that resulted from the design reviews and the
JAA recommendation and EASA policy statement mentioned above.
Revision History: PAD [proposed airworthiness directive] 06-
018R1 has been issued to endorse comments received for PAD 06-018
and due to the change of the EASA policy statement on fuel tank
safety on March 2006.
Compliance
(f) You are responsible for having the actions required by this
AD performed within the compliance times specified, unless the
actions have already been done.
Restatement of Requirements of AD 2006-12-18
Revision of Airplane Flight Manual (AFM)
(g) Within 30 days after July 21, 2006 (the effective date of AD
2006-12-18), revise the Limitations and Normal Procedures sections
of the AFMs as specified in Table 1 of this AD to include the
information in the applicable Shorts advance amendment bulletins as
specified in Table 1 of this AD. The advance amendment bulletins
address operation during icing conditions and fuel system failures.
Thereafter, operate the airplane according to the limitations and
procedures in the applicable advance amendment bulletin.
Note 2: The requirements of paragraph (g) of this AD may be
done by inserting a copy of the applicable advance amendment
bulletin into the AFM. When the applicable advance amendment
bulletin has been included in general revisions of the AFM, the
general revisions may be inserted into the AFM and the advance
amendment bulletin may be removed, provided the relevant information
in the general revision is identical to that in the advance
amendment bulletin.
Table 1--AFM Revisions
------------------------------------------------------------------------
Shorts advance
Airplane model-- amendment AFM--
bulletin--
------------------------------------------------------------------------
SD3-30 airplanes................ 1/2004, dated July SBH.3.2, SBH.3.3,
13, 2004. SBH.3.6, SBH.3.7,
SBH.3.8, and
SB.3.9.
SD3-60 airplanes................ 1/2004, dated July SB.4.3, SB.4.6,
13, 2004. and SB.4.8.
SD3-60 SHERPA airplanes......... 1/2004, dated July SB.6.2.
13, 2004.
SD3-SHERPA airplanes............ 1/2004, dated July SB.5.2.
13, 2004.
------------------------------------------------------------------------
Revision of Airworthiness Limitation (AWL) Section
(h) Within 180 days after July 21, 2006: Revise the AWL section
of the Instructions for Continued Airworthiness by incorporating
airplane maintenance manual (AMM) Sections 5-20-01 and 5-20-02 as
introduced by the Shorts temporary revisions (TR) specified in Table
2 of this AD into the AWL section of the AMMs for the airplane
models specified in Table 2 of this AD, except as required by
paragraph (j) of this AD. Thereafter, except as provided by
paragraph (m)(1) of this AD, no alternative structural inspection
intervals may be approved for the longitudinal skin joints in the
fuselage shell.
[[Page 1988]]
Note 3: The requirements of paragraph (h) of this AD may be
done by inserting a copy of the applicable TR into the applicable
AMM. When the TR has been included in general revisions of the AMM,
the general revisions may be inserted in the AMM and the TR may be
removed, provided the relevant information in the general revision
is identical to that in the TR.
Table 2--AMM Temporary Revisions
----------------------------------------------------------------------------------------------------------------
Airplane model-- Temporary revision-- Date-- AMM--
----------------------------------------------------------------------------------------------------------------
SD3-30 airplanes..................... TR330-AMM-13........... June 21, 2004.......... SD3-30 AMM.
SD3-30 airplanes..................... TR330-AMM-14........... June 21, 2004.......... SD3-30 AMM.
SD3-60 airplanes..................... TR360-AMM-33........... July 27, 2004.......... SD3-60 AMM.
SD3-60 airplanes..................... TR360-AMM-34........... July 27, 2004.......... SD3-60 AMM.
SD3-60 SHERPA airplanes.............. TRSD360S-AMM-14........ July 29, 2004.......... SD3-60 SHERPA AMM.
SD3-60 SHERPA airplanes.............. TRSD360S-AMM-15........ July 29, 2004.......... SD3-60 SHERPA AMM.
SD3-SHERPA airplanes................. TRSD3S-AMM-15.......... July 28, 2004.......... SD3 SHERPA AMM.
SD3-SHERPA airplanes................. TRSD3S-AMM-16.......... July 28, 2004.......... SD3 SHERPA AMM.
----------------------------------------------------------------------------------------------------------------
Resistance Check, Inspection, and Jumper Installation
(i) Within 180 days after July 21, 2006: Perform the insulation
resistance check, general visual inspections, and bonding jumper
wire installations; in accordance with Shorts Service Bulletin
SD330-28-37, SD360-28-23, SD360 SHERPA-28-3, or SD3 SHERPA-28-2; all
dated June 2004; as applicable. If any defect or damage is
discovered during any inspection or check required by this AD,
before further flight, repair the defect or damage using a method
approved by the Manager, International Branch, ANM-116, Transport
Airplane Directorate, FAA; the Civil Aviation Authority (CAA) (or
its delegated agent); or EASA (or its delegated agent).
Note 4: For the purposes of this AD, a general visual
inspection is: ``A visual examination of an interior or exterior
area, installation, or assembly to detect obvious damage, failure,
or irregularity. This level of inspection is made from within
touching distance unless otherwise specified. A mirror may be
necessary to ensure visual access to all surfaces in the inspection
area. This level of inspection is made under normally available
lighting conditions such as daylight, hangar lighting, flashlight,
or droplight and may require removal or opening of access panels or
doors. Stands, ladders, or platforms may be required to gain
proximity to the area being checked.''
New Requirements of This AD
Revision of AWL Section: New Limitations and CDCCLs
(j) Within 90 days after the effective date of this AD: Revise
the AWL section of the Instructions for Continued Airworthiness by
incorporating maintenance manual Sections 5-20-01 and 5-20-02 as
introduced by the Bombardier and Shorts TRs specified in Table 3 of
this AD into the AWL section of the maintenance manuals for the
airplane models specified in Table 3 of this AD. Doing this revision
terminates the requirement to incorporate the temporary revisions
specified in paragraph (h) of this AD. After doing this revision the
temporary revisions required by paragraph (h) of this AD may be
removed.
Table 3--Newly Required Maintenance Manual Temporary Revisions
----------------------------------------------------------------------------------------------------------------
Model-- Temporary revision-- Date-- Manual--
----------------------------------------------------------------------------------------------------------------
SD3-30 airplanes..................... Shorts TR TR330-AMM-35. June 6, 2006........... Shorts SD3-30
Maintenance Manual
(MM).
SD3-30 airplanes..................... Shorts TR TR330-AMM-36. June 6, 2006........... Shorts SD3-30 MM.
SD3-60 airplanes..................... Bombardier TR TR360-AMM- November 11, 2005...... Bombardier SD3-60 AMM.
55.
SD3-60 airplanes..................... Bombardier TR TR360-AMM- November 11, 2005...... Bombardier SD3-60 AMM.
56.
SD3-60 SHERPA airplanes.............. Shorts TR TRSD360S-AMM- June 27, 2006.......... Shorts SD3-60 SHERPA
35. MM.
SD3-60 SHERPA airplanes.............. Shorts TR TRSD360S-AMM- June 27, 2006.......... Shorts SD3-60 SHERPA
36. MM.
SD3-SHERPA airplanes................. Shorts TR TRSD3S-AMM-36 June 19, 2006.......... Shorts SD3-SHERPA MM.
SD3-SHERPA airplanes................. Shorts TR TRSD3S-AMM-37 June 19, 2006.......... Shorts SD3-SHERPA MM.
----------------------------------------------------------------------------------------------------------------
Note 5: The requirements of paragraph (j) of this AD may be
done by inserting a copy of the applicable TR into the applicable
maintenance manual. When the TR has been included in general
revisions of the AMM, the general revisions may be inserted in the
AMM and the TR may be removed, provided the relevant information in
the general revision is identical to that in the TR.
(k) After accomplishing the actions specified in paragraph (j)
of this AD, no alternative inspections, inspection intervals, or
CDCCLs may be used unless the inspections, intervals, or CDCCLs are
approved as an alternative method of compliance (AMOC), in
accordance with the procedures specified in paragraph (m) of this
AD.
Explanation of CDCCL Requirements
Note 6: Notwithstanding any other maintenance or operational
requirements, components that have been identified as airworthy or
installed on the affected airplanes before the revision of the AMM,
as required by paragraph (h) or (j) of this AD, do not need to be
reworked in accordance with the CDCCLs. However, once the AMM has
been revised, future maintenance actions on these components must be
done in accordance with the CDCCLs.
Credit for Actions Accomplished in Accordance With Other Service
Information
(l) Revising the AFM, as required by paragraph (g) of this AD,
by inserting Shorts Advance Amendment Bulletin 1/2004, dated 7/13/
04, for Model SD3-60 Sherpa airplanes, into AFM SB.5.2; or Shorts
Advance Amendment Bulletin 1/2004, dated 7/13/04, for Model SD3-
sherpa airplanes, into AFM SB.6.2; before the effective date of this
AD is acceptable for compliance with the AFM revision required by
paragraph (g) of this AD.
FAA AD Differences
Note 7: This AD differs from the MCAI and/or service
information as follows: No differences.
Other FAA AD Provisions
(m) The following provisions also apply to this AD:
(1) Alternative Methods of Compliance (AMOCs): The Manager,
International Branch, ANM-116, Transport Airplane Directorate, FAA,
has the authority to approve AMOCs for this AD, if requested using
the procedures found in 14 CFR 39.19. Send information to ATTN: Todd
Thompson, Aerospace Engineer, International Branch, ANM-116,
Transport Airplane Directorate, FAA, 1601 Lind Avenue, SW., Renton,
Washington 98057-3356; telephone (425) 227-1175; fax (425) 227-1149.
Before using any approved AMOC on any airplane to which the AMOC
applies, notify your
[[Page 1989]]
principal maintenance inspector (PMI) or principal avionics
inspector (PAI), as appropriate, or lacking a principal inspector,
your local Flight Standards District Office. The AMOC approval
letter must specifically reference this AD.
(2) Airworthy Product: For any requirement in this AD to obtain
corrective actions from a manufacturer or other source, use these
actions if they are FAA-approved. Corrective actions are considered
FAA-approved if they are approved by the State of Design Authority
(or their delegated agent). You are required to assure the product
is airworthy before it is returned to service.
(3) Reporting Requirements: A Federal agency may not conduct or
sponsor, and a person is not required to respond to, nor shall a
person be subject to a penalty for failure to comply with a
collection of information subject to the requirements of the
Paperwork Reduction Act unless that collection of information
displays a current valid OMB Control Number. The OMB Control Number
for this information collection is 2120-0056. Public reporting for
this collection of information is estimated to be approximately 5
minutes per response, including the time for reviewing instructions,
completing and reviewing the collection of information. All
responses to this collection of information are mandatory. Comments
concerning the accuracy of this burden and suggestions for reducing
the burden should be directed to the FAA at: 800 Independence Ave.,
SW., Washington, DC 20591, Attn: Information Collection Clearance
Officer, AES-200.
Related Information
(n) Refer to MCAI EASA Airworthiness Directive 2006-0198, dated
July 11, 2006; Shorts Service Bulletins SD330-28-37, SD360-28-23,
SD360 SHERPA-28-3, and SD3 SHERPA-28-2, all dated June 2004; and the
service information listed in Tables 1, 2, and 3 of this AD; for
related information.
Material Incorporated by Reference
(o) You must use the service information contained in Table 4 of
this AD, as applicable, to do the actions required by this AD,
unless the AD specifies otherwise.
Table 4--All Material Incorporated by Reference
------------------------------------------------------------------------
Document Date Manual
------------------------------------------------------------------------
Shorts Advance Amendment July 13, 2004..... Shorts Airplane
Bulletin 1/2004. Flight Manuals
(AFMs) SBH.3.2,
SBH.3.3, SBH.3.6,
SBH.3.7, SBH.3.8,
and SB.3.9.
Shorts Advance Amendment July 13, 2004..... Shorts AFMs
Bulletin 1/2004. SB.4.3, SB.4.6,
and SB.4.8.
Shorts Advance Amendment July 13, 2004..... Shorts AFM SB.5.2.
Bulletin 1/2004.
Shorts Advance Amendment July 13, 2004..... Shorts AFM SB.6.2.
Bulletin 1/2004.
Shorts TR330-AMM-13............. June 21, 2004..... Shorts SD3-30
Airplane
Maintenance
Manual (AMM).
Shorts TR330-AMM-14............. June 21, 2004..... Shorts SD3-30 AMM.
Shorts TR360-AMM-33............. July 27, 2004..... Shorts SD3-60 AMM.
Shorts TR360-AMM-34............. July 27, 2004..... Shorts SD3-60 AMM.
Shorts TRSD360S-AMM-14.......... July 29, 2004..... Shorts SD3-60
SHERPA AMM.
Shorts TRSD360S-AMM-15.......... July 29, 2004..... Shorts SD3-60
SHERPA AMM.
Shorts TRSD3S-AMM-15............ July 28, 2004..... Shorts SD3 SHERPA
AMM.
Shorts TRSD3S-AMM-16............ July 28, 2004..... Shorts SD3 SHERPA
AMM.
Shorts Service Bulletin SD330-28- June 2004......... None.
37.
Shorts Service Bulletin SD360-28- June 2004......... None.
23.
Shorts Service Bulletin SD360 June 2004......... None.
SHERPA-28-3.
Shorts Service Bulletin SD3 June 2004......... None.
SHERPA-28-2.
Shorts TR TR330-AMM-35.......... June 6, 2006...... Shorts SD3-30
Maintenance
Manual (MM).
Shorts TR TR330-AMM-36.......... June 6, 2006...... Shorts SD3-30 MM.
Bombardier TR TR360-AMM-55...... November 11, 2005. Bombardier SD3-60
AMM.
Bombardier TR TR360-AMM-56...... November 11, 2005. Bombardier SD3-60
AMM.
Shorts TR TRSD360S-AMM-35....... June 27, 2006..... Shorts SD3-60
SHERPA MM.
Shorts TR TRSD360S-AMM-36....... June 27, 2006..... Shorts SD3-60
SHERPA MM.
Shorts TR TRSD3S-AMM-36......... June 19, 2006..... Shorts SD3-SHERPA
MM.
Shorts TR TRSD3S-AMM-37......... June 19, 2006..... Shorts SD3-SHERPA
MM.
------------------------------------------------------------------------
(1) The Director of the Federal Register approved the
incorporation by reference of the service information contained in
Table 5 of this AD under 5 U.S.C. 552(a) and 1 CFR part 51.
Table 5--New Material Incorporated by Reference
------------------------------------------------------------------------
Document Date Manual
------------------------------------------------------------------------
Shorts TR TR330-AMM-35.......... June 6, 2006...... Shorts SD3-30 MM.
Shorts TR TR330-AMM-36.......... June 6, 2006...... Shorts SD3-30 MM.
Bombardier TR TR360-AMM-55...... November 11, 2005. Bombardier SD3-60
AMM.
Bombardier TR TR360-AMM-56...... November 11, 2005. Bombardier SD3-60
AMM.
Shorts TR TRSD360S-AMM-35....... June 27, 2006..... Shorts SD3-60
SHERPA MM.
Shorts TR TRSD360S-AMM-36....... June 27, 2006..... Shorts SD3-60
SHERPA MM.
Shorts TR TRSD3S-AMM-36......... June 19, 2006..... Shorts SD3-SHERPA
MM.
Shorts TR TRSD3S-AMM-37......... June 19, 2006..... Shorts SD3-SHERPA
MM.
------------------------------------------------------------------------
(2) The Director of the Federal Register previously approved
the incorporation by reference of the service information contained
in Table 6 of this AD on July 21, 2006 (71 FR 34801, June 16, 2006).
[[Page 1990]]
Table 6--Material Previously Incorporated by Reference
------------------------------------------------------------------------
Document Date Manual
------------------------------------------------------------------------
Shorts Advance Amendment July 13, 2004..... Shorts Airplane
Bulletin 1/2004. Flight Manuals
(AFMs) SBH.3.2,
SBH.3.3, SBH.3.6,
SBH.3.7, SBH.3.8,
and SB.3.9.
Shorts Advance Amendment July 13, 2004..... Shorts AFMs
Bulletin 1/2004. SB.4.3, SB.4.6,
and SB.4.8.
Shorts Advance Amendment July 13, 2004..... Shorts AFM SB.5.2.
Bulletin 1/2004.
Shorts Advance Amendment July 13, 2004..... Shorts AFM SB.6.2.
Bulletin 1/2004.
Shorts Temporary Revision TR330- June 21, 2004..... SD3-30 AMM.
AMM-13.
Shorts Temporary Revision TR330- June 21, 2004..... SD3-30 AMM.
AMM-14.
Shorts Temporary Revision TR360- July 27, 2004..... SD3-60 AMM.
AMM-33.
Shorts Temporary Revision TR360- July 27, 2004..... SD3-60 AMM.
AMM-34.
Shorts Temporary Revision July 29, 2004..... SD3-60 SHERPA AMM.
TRSD360S-AMM-14.
Shorts Temporary Revision July 29, 2004..... SD3-60 SHERPA AMM.
TRSD360S-AMM-15.
Shorts Temporary Revision TRSD3S- July 28, 2004..... SD3 SHERPA AMM.
AMM-15.
Shorts Temporary Revision TRSD3S- July 28, 2004..... SD3 SHERPA AMM.
AMM-16.
Shorts Service Bulletin SD330-28- June 2004......... None.
37.
Shorts Service Bulletin SD360-28- June 2004......... None.
23.
Shorts Service Bulletin SD360 June 2004......... None.
SHERPA-28-3.
Shorts Service Bulletin SD3 June 2004......... None.
SHERPA-28-2.
------------------------------------------------------------------------
(3) For service information identified in this AD, contact Short
Brothers PLC, Airworthiness, P.O. Box 241, Airport Road, Belfast,
BT3 9DZ Northern Ireland; telephone +44(0)2890-462469; fax
+44(0)2890-468444; e-mail [email protected];
Internet http://www.bombardier.com.
(4) You may review copies of the service information at the FAA,
Transport Airplane Directorate, 1601 Lind Avenue, SW., Renton,
Washington. For information on the availability of this material at
the FAA, call 425-227-1221.
(5) You may also review copies of the service information that
is incorporated by reference at the National Archives and Records
Administration (NARA). For information on the availability of this
material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.
Issued in Renton, Washington, on November 10, 2010.
Jeffrey E. Duven,
Acting Manager, Transport Airplane Directorate, Aircraft Certification
Service.
[FR Doc. 2011-30 Filed 1-11-11; 8:45 am]
BILLING CODE 4910-13-P