[Code of Federal Regulations] [Title 10, Volume 3] [Revised as of January 1, 2001] From the U.S. Government Printing Office via GPO Access [CITE: 10CFR430.22] [Page 105-107] TITLE 10--ENERGY CHAPTER II--DEPARTMENT OF ENERGY PART 430--ENERGY CONSERVATION PROGRAM FOR CONSUMER PRODUCTS--Table of Contents Subpart B--Test Procedures Sec. 430.22 Reference Sources. (a) Materials incorporated by reference.--(1) General. The following standards which are not otherwise set forth in Part 430 are incorporated by reference and made a part of Part 430. The standards listed in this section have been approved for incorporation by reference by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR Part 51. The specified versions of the standards are incorporated, and any subsequent amendment to a standard by the standard-setting organization will not affect the DOE test procedures unless and until those test procedures are amended by DOE. (2) Availability of standards. The standards incorporated by reference are available for inspection at: (i) Office of the Federal Register Information Center, 800 North Capitol Street, NW., Suite 700, Washington, DC. (ii) U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Hearings and Dockets, Forrestal Building, 1000 Independence Ave, SW, Washington, DC 20585. (b) List of Sources and Standards Incorporated by Reference. (1) American National Standards Institute (ANSI). The ANSI standards listed in this paragraph may be obtained from the American National Standards Institute, 1430 Broadway, New York, NY 10018, (212) 642-4900. [[Page 106]] 1. ANSI C78.1-1991, ``for Fluorescent Lamps--Rapid-Start Types-- Dimensional and Electrical Characteristics'' 2. ANSI C78.2-1991, ``for Fluorescent Lamps--Preheat-Start Types-- Dimensional and Electrical Characteristics of Fluorescent Lamps'' 3. ANSI C78.3-1991, ``for Fluorescent Lamps--Instant-Start and Cold- Cathode Types--Dimensional and Electrical Characteristics'' 4. ANSI C78.375-1991, ``for Fluorescent Lamps--Guide for Electrical Measurements'' 5. ANSI C82.3-1983 ``for Reference Ballasts for Fluorescent Lamps'' 6. ANSI C79.1-1994, ``Nomenclature for Glass Bulbs--Intended for Use with Electric Lamps'' 7. ANSI C78.21-1989, ``Incandescent Lamps--PAR and R Shapes'' (2) Illuminating Engineering Society of North America (IESNA). The IESNA standards listed in this paragraph may be obtained from the Illuminating Engineering Society of North America, 120 Wall Street, Floor 17, New York, NY 10005-4001, (212) 248-5000. 1. Illuminating Engineering Society LM-9-88, ``IES Approved Method for the Electrical and Photometric Measurements of Fluorescent Lamps'' 2. Illuminating Engineering Society of North America LM-16-1993, ``IESNA Practical Guide to Colorimetry of Light Sources'' 3. Illuminating Engineering Society of North America LM-20-1994, ``IESNA Approved Method for Photometric Testing of Reflector-Type Lamps'' 4. Illuminating Engineering Society of North America LM-45-91, ``IES Approved Method for Electrical and Photometric Measurements of General Service Incandescent Filament Lamps'' 5. Illuminating Engineering Society of North America LM-58-1994, ``IESNA Guide to Spectroradiometric Measurements'' 6. Illuminating Engineering Society of North America LM-66-1991, ``IES Approved Method for the Electrical and Photometric Measurements of Single-Ended Compact Fluorescent Lamps'' 7. Illuminating Engineering Society of North America Lighting Handbook, Reference and Application, 8th Edition, 1993, Chapter 6, Light Sources (3) International Commission on Illumination (CIE). The CIE standards listed in this paragraph may be obtained from the International Commission on Illumination, CIE Bureau Central, Kegelgasse 27, A-1030, Vienna, Austria. CIE publications are also available from TLA Lighting Consultants, 7 Pond Street, Salem, MA 10970, (508) 745- 6870. 1. International Commission on Illumination (CIE) Publication No. 13.2 1974, corrected reprint 1993, ``Method of Measuring and Specifying Color Rendering Properties of Light Sources,'' ISBN 3 900 734 39 9 (4) International Electrotechnical Commission. Copies of the International Electrotechnical Commission Publications can be obtained from the American National Standards Institute, 11 West 42nd Street, New York, New York 10036, (212) 642-4936. 1. IEC 705, ``Methods for Measuring the Performance of Microwave Ovens for Household and Similar Purposes,'' Section 4, Methods of Measurement, Paragraph 13 ``Electrical Power Input Measurement,'' and Paragraph 14 ``Efficiency'' (1988). 2. IEC 705, Amendment 2, ``Methods for Measuring the Performance of Microwave Ovens for Household and Similar Purposes,'' Section 4, Methods of Measurement, Paragraph 12 ``Microwave Power Output Measurement'' (1993). (5) American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc., Publication Sales, 1791 Tullie Circle, NE, Atlanta, GA 30329, (1-800-5-ASHRAE). 1. American National Standards Institute/American Society of Heating, Refrigerating, and Air-Conditioning Engineers Standard 103- 1993, ``Methods of Testing for Annual Fuel Utilization Efficiency of Residential Central Furnaces and Boilers,'' (with Errata of October 24, 1996) except for sections 3.0, 7.2.2.5, 8.6.1.1, 9.1.2.2, 9.5.1.1, 9.5.1.2.1, 9.5.1.2.2, 9.5.2.1, 9.7.1, 10.0, 11.2.12, 11.3.12, 11.4.12, 11.5.12 and appendices B and C. 2. American National Standards Institute Standard Z21.56-1994, ``Gas- Fired Pool Heaters,'' section 2.9. (6) American Society of Mechanical Engineers (ASME). The ASME standards listed in this paragraph may be obtained from the American Society of Mechanical Engineers, Service Center, 22 Law Drive, P.O. Box 2900, Fairfield, NJ 07007. 1. ASME/ANSI Standard A112.18.1M-1996, ``Plumbing Fixture Fittings.'' 2. ASME/ANSI Standard A112.19.6-1995, ``Hydraulic Requirements for Water Closets and Urinals.'' [[Page 107]] (c) Reference Standards. (1) General. The standards listed in this paragraph are referred to in the DOE test procedures and elsewhere in 10 CFR part 430 but are not incorporated by reference. These sources are given here for information and guidance. (2) List of References. 1. National Voluntary Laboratory Accreditation Program Handbook 150- 01, ``Energy Efficient Lighting Products, Lamps and Luminaires, August 1993.'' National Voluntary Laboratory Accreditation Program, NIST, Gaithersburg, MD. 2. ``Illuminating Engineering Society Lighting Handbook,'' 8th Edition, New York, NY 1993. [59 FR 49474, Sept. 28, 1994, as amended at 62 FR 29239, May 29, 1997; 62 FR 51981, Oct. 3, 1997; 63 FR 13316, Mar. 18, 1998]