[Code of Federal Regulations] [Title 49, Volume 5] [Revised as of October 1, 2002] From the U.S. Government Printing Office via GPO Access [CITE: 49CFR583.5] [Page 957-959] TITLE 49--TRANSPORTATION OF TRANSPORTATION PART 583--AUTOMOBILE PARTS CONTENT LABELING--Table of Contents Sec. 583.5 Label requirements. (a) Except as provided in paragraphs (f) and (g) of this section, each manufacturer of new passenger motor vehicles shall cause to be affixed to each passenger motor vehicle manufactured on or after October 1, 1994, a label that provides the following information: (1) U.S./Canadian parts content. The overall percentage, by value, of the passenger motor vehicle equipment that was installed on vehicles within the carline of which the vehicle is part, and that originated in the United States and/or Canada (the procedure for determining U.S./ Canadian Parts Content is set forth in Sec. 583.6); (2) Major sources of foreign parts content. The names of any countries other than the United States and Canada which contributed at least 15 percent of the average overall percentage, by value, of the passenger motor vehicle equipment installed on vehicles within the carline of which the vehicle is part, and the percentages attributable to each such country (if there are more than two such countries, the manufacturer need only provide the information for the two countries with the highest percentages; the procedure for determining major foreign sources of passenger motor vehicle equipment is set forth in Sec. 583.7); (3) Final assembly point. The city, state (in the case of vehicles assembled in the United States), and country of the final assembly point of the passenger motor vehicle; (4) Country of origin for the engine. The country of origin of the passenger motor vehicle's engine (the procedure for making this country of origin determination is set forth in Sec. 583.8); (5) Country of origin for the transmission. The country of origin of the passenger motor vehicle's transmission (the procedure for making this country of origin determination is set forth in Sec. 583.8); (6) Explanatory note. A statement which explains that parts content does not include final assembly, distribution, or other non-parts costs. [[Page 958]] (b) Except as provided in paragraphs (e), (f) and (g) of this section, the label required under paragraph (a) of this section shall read as follows, with the specified information inserted in the places indicated (except that if there are no major sources of foreign parts content, omit the section ``Major Sources of Foreign Parts Content''): Parts Content Information For vehicles in this carline: U.S./Canadian Parts Content: (insert number) % Major Sources of Foreign Parts Content: (Name of country with highest percentage): (insert number) % (Name of country with second highest percentage): (insert number) % Note: Parts content does not include final assembly, distribution, or other non-parts costs. For this vehicle: Final Assembly Point: (city, state, country) Country of Origin: Engine: (name of country) Transmission: (name of country) (c) The percentages required to be provided under paragraph (a) of this section may be rounded by the manufacturer to the nearest 5 percent. (d) The label required by paragraph (a) of this section shall: (1) Be placed in a prominent location on each vehicle where it can be read from the exterior of the vehicle with the doors closed, and may be either part of the Monroney price information label required by 15 U.S.C. 1232, part of the fuel economy label required by 15 U.S.C. 2006, or a separate label. A separate label may include other consumer information. (2)(i) Be printed in letters that have a color that contrasts with the background of the label; and (ii) Have the information required by paragraphs (a)(1) through (5) of this section vertically centered on the label in boldface capital letters and numerals of 12 point size or larger; and (iii) Have the information required by paragraph (a)(6) of this section in type that is two points smaller than the information required by paragraphs (a)(1) through (5) of this section. (3) In the case of a label that is included as part of the Monroney price information label or fuel economy label, or a separate label that includes other consumer information, be separated from all other information on those labels by a solid line that is a minimum of three points in width. (4) The information required by paragraphs (a)(1) through (6) of this section shall be immediately preceded by the words, ``PARTS CONTENT INFORMATION,'' in boldface, capital letters that are 12 point size or larger. (e) Carlines assembled in the U.S./Canada and in one or more other countries. (1) If a carline is assembled in the U.S. and/or Canada, and in one or more other countries, the manufacturer may, at its option, add the following additional information at the end of the explanatory note specified in (a)(6), with the specified information inserted in the places indicated: This carline is assembled in the U.S. and/or Canada, and in [insert name of each other country]. The U.S./Canadian parts content for the portion of the carline assembled in [insert name of country, treating the U.S. and Canada together, i.e., U.S./Canada] is [----]%. (2) A manufacturer selecting this option shall divide the carline for purposes of this additional information into the following portions: the portion assembled in the U.S./Canada and the portions assembled in each other country. (3) A manufacturer selecting this option for a particular carline shall provide the specified additional information on the labels of all vehicles within the carline, providing the U.S./Canadian content that corresponds to the U.S./Canadian content of the manufacturing location shown as the final assembly point (with all U.S. and Canadian locations considered as a single assembly point) on the label. (f) A final stage manufacturer of vehicles assembled in multiple stages need not provide the U.S./Canadian Parts Content or Major Foreign Sources items of the label otherwise required under paragraphs (a)(1) and (2) of this section. (g) A manufacturer that produces a total of fewer than 1000 passenger motor vehicles in a model year need not provide the U.S./ Canadian Parts Content or Major Foreign Sources items of the label otherwise required [[Page 959]] under paragraphs (a)(1) and (2) of this section. (h) Requests for information and certifications relevant to information on the label. (1) Each manufacturer and allied supplier shall request its suppliers to provide directly to it the information and certifications specified by this part which are necessary for the manufacturer/allied supplier to carry out its responsibilities under this part. The information shall be requested sufficiently early to enable the manufacturer to meet the timing requirements specified by this part. (2) For requests made by manufacturers or allied suppliers to outside suppliers: (i) The requester shall indicate that the request is being made pursuant to 49 CFR part 583, and that the regulation is administered by the National Highway Traffic Safety Administration; (ii) The requester shall indicate that 49 CFR part 583 requires outside suppliers to provide specified information upon the request of a manufacturer or allied supplier to which it supplies passenger motor vehicle equipment and that, to the best of the requester's knowledge, the outside supplier is required to provide the requested information; (iii) If any information other than that required by 49 CFR part 583 is requested, the requester shall indicate which information is required by 49 CFR part 583 and which is not; (iv) The requester shall indicate that 49 CFR part 583 specifies that while information may be requested by an earlier date, the outside supplier is not required to provide the information until the date specified by the requester or the date 45 days after receipt of the request, whichever is later. (i) Carlines assembled in more than one assembly plant. (1) If a carline is assembled in more than one assembly plant, the manufacturer may, at its option, add the following additional information at the end of the explanatory note specified in paragraph (a)(6) of this section, with the specified information inserted in the places indicated: Two or more assembly plants produce the vehicles in this carline. The vehicles assembled at the plant where this vehicle was assembled have a U.S./Canadian parts content of [--]%. (2) A manufacturer selecting this option shall divide the carline for purposes of this additional information into portions representing each assembly plant. (3) A manufacturer selecting this option for a particular carline shall provide the specified additional information on the labels of all vehicles within the carline. [59 FR 37330, July 21, 1994, as amended at 60 FR 14229, Mar. 16, 1995; 60 FR 47893, Sept. 15, 1995; 64 FR 40780, July 28, 1999]