[Code of Federal Regulations] [Title 16, Volume 2] [Revised as of January 1, 2003] From the U.S. Government Printing Office via GPO Access [CITE: 16CFR1209.11] [Page 294-309] TITLE 16--COMMERCIAL PRACTICES CHAPTER II--CONSUMER PRODUCT SAFETY COMMISSION PART 1209--INTERIM SAFETY STANDARD FOR CELLULOSE INSULATION--Table of Contents Subpart A--The Standard Sec. 1209.11 Effective date. All cellulose insulation that is a consumer product and that is manufactured after October 15, 1979 shall meet the requirements of this standard, including the labeling requirement of Sec. 1209.9. [[Page 295]] Figure 1 to Subpart A of Part 1209--Partial Insulation Preparation Apparatus [GRAPHIC] [TIFF OMITTED] TC03OC91.031 [[Page 296]] Figure 2 to Subpart A of Part 1209--Cyclone Receiver Weldment [GRAPHIC] [TIFF OMITTED] TC03OC91.032 [[Page 297]] Figure 3 to Subpart A of Part 1209--Flooring Radiant Tester Schematic Side Elevation [GRAPHIC] [TIFF OMITTED] TC03OC91.033 [[Page 298]] Figure 4 to Subpart A of Part 1209--Flooring Radiant Panel Tester Schematic Low Flux End, Elevation [GRAPHIC] [TIFF OMITTED] TC03OC91.034 [[Page 299]] Figure 5 to Subpart A of Part 1209--Zero Reference Point Related to Detecting Plane [GRAPHIC] [TIFF OMITTED] TC03OC91.035 [[Page 300]] Figure 6 to Subpart A of Part 1209--Dummy Specimen in Specimen Holder [GRAPHIC] [TIFF OMITTED] TC03OC91.036 [[Page 301]] Figure 7 to Subpart A of Part 1209--Specimen Tray [GRAPHIC] [TIFF OMITTED] TC03OC91.037 [[Page 302]] Figure 8 to Subpart A of Part 1209--Standard Radiant Heat Energy Flux Profile [GRAPHIC] [TIFF OMITTED] TC03OC91.038 [[Page 303]] Figure 9 to Subpart A of Part 1209--Flux Profile Data Log Format [GRAPHIC] [TIFF OMITTED] TC03OC91.039 [[Page 304]] Figure 10 to Subpart A of Part 1209--Insulation Radiant Panel Test Data Log Format [GRAPHIC] [TIFF OMITTED] TC03OC91.040 Subpart B--Certification Authority: Secs. 14, 16; 86 Stat. 1220, 1222; (15 U.S.C. 2063, 2065). Sec. 1209.31 Purpose and applicability. (a) Purpose. The purpose of this subpart B of part 1209 is to establish requirements that manufacturers, importers, and private labelers must follow to certify that their products comply with the Amended Interim Standard for Cellulose Insulation (16 CFR part 1209, subpart A). This subpart B includes requirements for conducting a reasonable testing program, certifying with labels and separate certificates, and recordkeeping. (b) Applicability. (1) Cellulose insulation which is subject to the standard includes all cellulose insulation, manufactured after the effective date (as described in Sec. 1209.41), produced or distributed for sale to, or for the personal use, consumption, or enjoyment of, consumers in or around a permanent or temporary household or residence, a school, in recreation or otherwise. The standard applies to cellulose insulation [[Page 305]] that is produced or distributed for sale to consumers, for their direct installation or use, as well as cellulose insulation that is produced or distributed for installation by professionals. (2) The term cellulose insulation is defined in Sec. 1209.2(a) of the standard to mean cellulosic fiber, loose fill, thermal insulation that is suitable for blowing or pouring applications. Sec. 1209.32 Definitions. In addition to the definitions set forth in section 3 of the act and in Sec. 1209.2 of the standard, the following definitions shall apply to this subpart: Private labeler means an owner of a brand or trademark which is used on the label of cellulose insulation subject to the standard which bears a private label as defined in section 3(a)(7) of the act (15 U.S.C. 2052(a)(7)). Production interval means a time span determined by the manufacturer, private labeler, or importer to be appropriate for conducting a test or series of tests on samples of the cellulose insulation being produced to demonstrate that the product meets the requirements of the standard. An appropriate production interval may vary from test to test. The time period for a production interval shall be short enough to ensure that if the samples selected for testing comply with the standard or a portion of the standard, the insulation produced during the period will meet the standard or the appropriate portion of the standard. Sec. 1209.33 Reasonable testing program. (a) General. Section 14(a) of the Consumer Product Safety Act (15 U.S.C. 2063(a)) requires each manufacturer, importer, or private labeler of a product which is subject to a consumer product safety standard to issue a certificate of compliance with the applicable standard and to base that certificate upon a test of each item or upon a reasonable testing program. Because it is not practical to test each item subject to the standard, a reasonable testing program shall be used to support certificates of compliance for cellulose insulation. (b) Requirements of testing program. A reasonable testing program for cellulose insulation is one which demonstrates with reasonable certainty that insulation certified to comply with the standard will meet all requirements of the standard. Manufacturers, private labelers, and importers shall determine the types and frequency of testing for their own reasonable testing programs. A reasonable testing program may include either the tests prescribed by the standard, or any other reasonable test procedures. However, a reasonable testing program cannot consist of tests which the party issuing the certificate of compliance knows (or through the exercise of reasonable diligence should know) will pass or accept insulation which will yield failing results when subjected to any of the tests in the standard. All reasonable testing programs shall consist of four elements: (1) Qualification tests which must be performed on samples of the manufacturer's cellulose insulation to demonstrate that the product is capable of passing the tests prescribed by the standard. (2) A description of the cellulose insulation which passed the qualification testing. This description is known as the ``product specification.'' (3) Production tests, which must be performed at appropriate production intervals as long as the cellulose insulation is being manufactured. (4) Corrective action, which must be taken whenever samples of the cellulose insulation yield unacceptable or failing test results. (c) Commission testing. The Commission will test for compliance with the standard by using the test procedures contained in the standard, and will base enforcement actions for violation of the standard on the results of such testing. (d) Testing by third parties. At the option of the manufacturer, importer, or private labeler, some or all of the testing for the reasonable testing program may be performed by a commercial testing laboratory. However, the manufacturer, importer, or private labeler is responsible for ensuring that all testing used to support the certificate of compliance has been properly performed with passing or acceptable results and for maintaining all records of [[Page 306]] such tests in accordance with Sec. 1209.38 below. Sec. 1209.34 Qualification testing. (a) Requirement. Before any manufacturer, importer, or private labeler begins distribution in commerce of cellulose insulation which is subject to the standard, samples of the insulation shall be tested for compliance with the standard. Manufacturers, importers, and private labelers shall determine the types of tests for qualification testing. (b) Timing, Sampling. Any or all of the qualification testing required by this Sec. 1209.34 may be performed before the effective date of the standard. Manufacturers, private labelers, or importers may select samples for qualification testing of a product in any manner they desire. Sec. 1209.35 Product specification. (a) Requirement. Before any manufacturer, importer, or private labeler distributes in commerce cellulose insulation which is subject to the standard, it shall ensure that the insulation is described in a written product specification. (b) Contents of Specification. The product specification shall include the following information: (1) A description of the equipment used to manufacture the insulation, including the model number and names of the equipment manufacturers, and details of any modification made to any item of equipment. (2) A description of the cellulosic stock material used to manufacture the insulation, identifying the extent of impurities allowed. (3) The formulation of the fire-retardant chemicals added, including their chemical constituents and their form (for example, granulated, powdered, or liquid); the amount of fire-retardant chemicals present in the finished insulation, expressed as a percentage of the total weight of chemicals and cellulosic stock; the average weight of chemicals per bag; and the name and address of each chemical supplier. Where the chemical composition or formula of a commercially pre-mixed fire retardant is not known to the insulation manufacturer, the pre-mixed fire retardant may be described simply by the name and address of the supplier and its brand or trade name. (4) A description of the tests which were used to qualify the product as well as the dates of performance and results and actual values, where applicable, of the tests. (5) Any other information necessary to describe the insulation. (c) Distribution in Commerce. After the qualification testing required by Sec. 1209.34 has been completed with acceptable results and the product specification required by this Sec. 1209.35 has been recorded, the cellulose insulation may be manufactured and distributed in commerce, subject to the provisions of Sec. 1209.36. (d) New Product. Whenever a manufacturer, private labeler, or importer makes any change to any item of equipment, cellulosic stock material, or formulation of a fire-retardant chemical, or any other factor which is likely to affect the ability of the cellulose insulation to meet the standard, that change will result in a new cellulose insulation product, requiring the preparation of a new product specification. The new product must be subjected to qualification tests and must yield passing or acceptable results. Sec. 1209.36 Production testing. (a) General. Manufacturers, private labelers, and importers shall test the cellulose insulation periodically as it is manufactured to demonstrate that the product being manufactured is substantially similar to the product which passed the qualification testing and to demonstrate that the product being manufactured meets the requirements of the standard. (b) Types and frequency of testing. Manufacturers, private labelers, and importers shall determine the types of tests for production testing. Each production test shall be conducted at a production interval short enough to ensure that if the samples selected for testing meet the standard or a portion of the standard, the insulation produced during the interval will also meet the standard or the appropriate portion of the standard. (c) Test failure. If any test yields failing results, production must cease and [[Page 307]] the faulty manufacturing process must be corrected (see Sec. 1209.37). In addition, the material from which the samples were taken may not be distributed in commerce unless the material can be corrected (see Sec. 1209.37) so as to yield passing results and meet the standard. Cellulose insulation that does not comply with the standard cannot be sold or offered for sale. Sec. 1209.37 Corrective actions. (a) Test failure. When any test required by Sec. 1209.36 yields failing or unacceptable results, corrective action must be taken. Corrective action includes changes to the manufacturing process as well as reworking the insulation product itself. Corrective action may consist of equipment adjustment, equipment repair, equipment replacement, change in chemical formulation, change in chemical quantity, change in cellulosic stock, or other action deemed appropriate by the manufacturer, private labeler or importer to achieve passing or acceptable test results. (b) New product. If any corrective action required by this Sec. 1209.37 results in a change in the product specification and a new cellulose insulation product (see Sec. 1209.34(b)), the product specification for the new product must be recorded in accordance with Sec. 1209.35, and qualification tests must be performed with passing or acceptable results in accordance with Sec. 1209.34, before the new product is distributed in commerce. Sec. 1209.38 Records. (a) Establishment and maintenance. Each manufacturer, importer, and private labeler of cellulose insulation subject to the standard shall establish and maintain the following records which shall be available to any designated officer or employee of the Commission upon request in accordance with section 16(b) of the act (15 U.S.C. 2965(b)): (1) A record of each product specification containing all information required by Sec. 1209.35. (This includes information concerning the types of qualification tests as well as the results from these tests.) (2) Records to demonstrate compliance with the requirements for production testing in Sec. 1209.36, including a description of the types of production tests conducted and the production interval selected for performance of each production test. (3) Records of all corrective actions taken in accordance with Sec. 1209.37, including the specific action taken, the date the action was taken, and the test failure which necessitated the action. Records of corrective action must relate the corrective action taken to the product specification of the insulation product which was the subject of that corrective action, and the product specification of any new product which results from any corrective action. (4) Records indicating exactly which insulation material is covered by each certificate of compliance issued. (b) Retention. (1) Product specification. The records of each product specification shall be retained for as long as the cellulose insulation covered by that specification is manufactured and for a period of two (2) years thereafter. (2) Other records. Records of production testing, corrective actions taken, and certificates issued shall be maintained for a period of two (2) years. (c) Confidentiality. Requests for confidentiality of records provided to the Commission will be handled in accordance with section 6(a)(2) of the CPSA (15 U.S.C. 2055(a)(2)), the Freedom of Information Act as amended (5 U.S.C. 552), and the Commission's regulations under that act (16 CFR part 1015, February 22, 1977). Sec. 1209.39 Certification of compliance. (a)(1) Responsibilities of manufacturer for insulation sold in bags. Manufacturers of cellulose insulation subject to the standard which is sold in bags or other containers shall certify compliance with the standard by marking each bag or container with the following information: (i) The statement ``This product meets the amended CPSC standard for flame resistance and corrosiveness of cellulose insulation.'' (This statement is the same statement provided in Sec. 1209.9 of the standard; it need not appear twice on the bag or container.) (ii) The name of the manufacturer, private labeler, or importer issuing the [[Page 308]] certificate of compliance. See paragraphs (b) and (c), below. (iii) The date of manufacture by day, month, and year. (iv) The place of manufacture, by city, state, and zip code, or in the case of products manufactured outside the United States, by city and country. The information required by this Sec. 1209.39(a) may appear anywhere on the bag or container. The information required need not appear at the same place on the bag or container. The information shall be permanent until the bag or container is opened and used. The information shall be conspicuous and must appear in letters and figures at least \1/4\ inch in height. The date and place of manufacture may be in code, provided the person or firm issuing the certificate maintains a written record of the meaning of the code that can be made available to consumers, persons in the chain of distribution, and the Commission upon request. (2) Insulation not sold in bags or containers. The manufacturer of cellulose insulation subject to the standard which is not sold in bags or other containers shall certify compliance with the standard by accompanying each shipment or delivery of the product, with a document such as an invoice, bill, statement, or separate document, which states the following: ``This product meets the amended CPSC standard for flame resistance and corrosiveness of cellulose insulation. This material was manufactured on (insert day, month, and year of manufacture) at (insert city, state, and zip code, or in the case of insulation manufactured outside the United States, city and country).'' The certificate of compliance must also contain the name of the manufacturer, private labeler, or importer issuing the certificate. See paragraphs (b) and (c), below. The certificate of compliance must appear in letters and figures which are conspicuous and legible. The date and place of manufacture may be in code, provided the person or firm issuing the certificate maintains a written record of the meaning of the code that can be made available to consumers, persons in the chain of distribution, and the Commission upon request. (b) Responsibilities of private labelers. A private labeler who distributes a product subject to the standard which is manufactured by another person or firm but which is sold under the private labeler's name, brand, or trademark must issue the certificate of compliance required by section 14 of the Consumer Product Safety Act and this section. If the testing required by this subpart has been performed by or for the manufacturer of the product, the private labeler may rely on any such tests to support the certificate of compliance if the records of such tests are maintained in accordance with Sec. 1209.38, above. The private labeler is responsible for ensuring that all testing used to support the certificate of compliance has been performed properly with passing or acceptable results, and that all records of such tests are accurate and complete. (c) Responsibilities of importers. The importer of any product subject to the standard must issue the certificate of compliance required by section 14(a) of the act and this Sec. 1209.39. If the testing required by this subpart B of part 1209 has been performed by or for the foreign manufacturer of the product, the importer may rely on any such tests to support the certificate of compliance if the importer is a resident of the U.S. or has a resident agent in the U.S. and the records are maintained in the U.S. in accordance with Sec. 1209.38 above. The importer is responsible for ensuring that all testing used to support the certificate of compliance has been performed properly with passing or acceptable results, and that all records of such tests are accurate and complete. Sec. 1209.40 Certification responsibility, multiple parties. If there is more than one party (i.e., manufacturer, private labeler, or importer) otherwise subject to the requirements of this subpart B of part 1209 for certain cellulose insulation, only the party closest to the consumer in the distribution chain is required to issue a certificate. Sec. 1209.41 Effective date. The requirements of this subpart B of part 1209 shall become effective on October 16, 1979. Any cellulose insulation [[Page 309]] manufactured after October 15, 1979 must be certified as complying with the standard. Cellulose insulation which is sold in bags or other containers is ``manufactured'' when the insulation is packaged in the bag or other container in which it will be sold. Insulation which is not sold in bags or containers is ``manufactured'' when the insulation leaves the manufacturing site to be sold.