[Code of Federal Regulations]
[Title 40, Volume 24]
[Revised as of July 1, 2003]
From the U.S. Government Printing Office via GPO Access
[CITE: 40CFR270.25]

[Page 299-300]
 
                   TITLE 40--PROTECTION OF ENVIRONMENT
 
                           AGENCY (CONTINUED)
 
PART 270--EPA ADMINISTERED PERMIT PROGRAMS: THE HAZARDOUS WASTE PERMIT PROGRAM--Table of Contents
 
                      Subpart B--Permit Application
 
Sec. 270.25  Specific part B information requirements for equipment.

    Except as otherwise provided in Sec. 264.1, owners and operators of 
facilities that have equipment to which subpart BB of part 264 applies 
must provide the following additional information:

[[Page 300]]

    (a) For each piece of equipment to which subpart BB of part 264 
applies:
    (1) Equipment identification number and hazardous waste management 
unit identification.
    (2) Approximate locations within the facility (e.g., identify the 
hazardous waste management unit on a facility plot plan).
    (3) Type of equipment (e.g., a pump or pipeline valve).
    (4) Percent by weight total organics in the hazardous waste stream 
at the equipment.
    (5) Hazardous waste state at the equipment (e.g., gas/vapor or 
liquid).
    (6) Method of compliance with the standard (e.g., ``monthly leak 
detection and repair'' or ``equipped with dual mechanical seals'').
    (b) For facilities that cannot install a closed-vent system and 
control device to comply with the provisions of 40 CFR 264 subpart BB on 
the effective date that the facility becomes subject to the provisions 
of 40 CFR 264 or 265 subpart BB, an implementation schedule as specified 
in Sec. 264.1033(a)(2).
    (c) Where an owner or operator applies for permission to use a 
control device other than a thermal vapor incinerator, catalytic vapor 
incinerator, flare, boiler, process heater, condenser, or carbon 
adsorption system and chooses to use test data to determine the organic 
removal efficiency or the total organic compound concentration achieved 
by the control device, a performance test plan as specified in 
Sec. 264.1035(b)(3).
    (d) Documentation that demonstrates compliance with the equipment 
standards in Secs. 264.1052 to 264.1059. This documentation shall 
contain the records required under Sec. 264.1064. The Regional 
Administrator may request further documentation before deciding if 
compliance has been demonstrated.
    (e) Documentation to demonstrate compliance with Sec. 264.1060 shall 
include the following information:
    (1) A list of all information references and sources used in 
preparing the documentation.
    (2) Records, including the dates, of each compliance test required 
by Sec. 264.1033(j).
    (3) A design analysis, specifications, drawings, schematics, and 
piping and instrumentation diagrams based on the appropriate sections of 
``ATPI Course 415: Control of Gaseous Emissions'' (incorporated by 
reference as specified in Sec. 260.11) or other engineering texts 
acceptable to the Regional Administrator that present basic control 
device design information. The design analysis shall address the vent 
stream characteristics and control device operation parameters as 
specified in Sec. 264.1035(b)(4)(iii).
    (4) A statement signed and dated by the owner or operator certifying 
that the operating parameters used in the design analysis reasonably 
represent the conditions that exist when the hazardous waste management 
unit is operating at the highest load or capacity level reasonably 
expected to occur.
    (5) A statement signed and dated by the owner or operator certifying 
that the control device is designed to operate at an efficiency of 95 
weight percent or greater.

[55 FR 25518, June 21, 1990, as amended at 56 FR 19290, Apr. 26, 1991]