[Code of Federal Regulations]
[Title 40, Volume 9]
[Revised as of July 1, 2003]
From the U.S. Government Printing Office via GPO Access
[CITE: 40CFR63.14]
[Page 61-65]
TITLE 40--PROTECTION OF ENVIRONMENT
CHAPTER I--ENVIRONMENTAL PROTECTION AGENCY (CONTINUED)
PART 63--NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS FOR SOURCE CATEGORIES--Table of Contents
Subpart A--General Provisions
Sec. 63.14 Incorporations by reference.
(a) The materials listed in this section are incorporated by
reference in the corresponding sections noted. These incorporations by
reference were approved by the Director of the Federal Register in
accordance with 5 U.S.C. 552(a) and 1 CFR part 51. These materials are
incorporated as they exist on the date of the approval, and notice of
any change in these materials will be published in the Federal Register.
The materials are available for purchase at the corresponding addresses
noted below, and all are available for inspection at the Office of the
Federal Register, 800 North Capitol Street, NW., suite 700, Washington,
DC, at the Air and Radiation Docket and Information Center, U.S. EPA,
401 M St., SW., Washington, DC, and at the EPA Library (MD-35), U.S.
EPA, Research Triangle Park, North Carolina.
(b) The following materials are available for purchase from at least
one of the following addresses: American Society for Testing and
Materials (ASTM), 100 Barr Harbor Drive, Post Office Box C700, West
Conshohocken,
[[Page 62]]
PA 19428-2959; or ProQuest, 300 North Zeeb Road, Ann Arbor, MI 48106.
(1) ASTM D523-89, Standard Test Method for Specular Gloss, IBR
approved for Sec. 63.782.
(2) ASTM D1193-77, 91, Standard Specification for Reagent Water, IBR
approved for Appendix A: Method 306, Sections 7.1.1 and 7.4.2.
(3) ASTM D1331-89, Standard Test Methods for Surface and Interfacial
Tension of Solutions of Surface Active Agents, IBR approved for Appendix
A: Method 306B, Sections 6.2, 11.1, and 12.2.2.
(4) ASTM D1475-90, Standard Test Method for Density of Paint,
Varnish Lacquer, and Related Products, IBR approved for Sec. 63.788,
Appendix A.
(5) ASTM D1946-77, 90, 94, Standard Method for Analysis of Reformed
Gas by Gas Chromatography, IBR approved for Sec. 63.11(b)(6).
(6) ASTM D2369-93, 95, Standard Test Method for Volatile Content of
Coatings, IBR approved for Sec. 63.788, Appendix A.
(7) ASTM D2382-76, 88, Heat of Combustion of Hydrocarbon Fuels by
Bomb Calorimeter (High-Precision Method), IBR approved for
Sec. 63.11(b)(6).
(8) ASTM D2879-83, 96, Test Method for Vapor Pressure-Temperature
Relationship and Initial Decomposition Temperature of Liquids by
Isoteniscope, IBR approved for Sec. 63.111 of Subpart G.
(9) ASTM D3257-93, Standard Test Methods for Aromatics in Mineral
Spirits by Gas Chromatography, IBR approved for Sec. 63.786(b).
(10) ASTM 3695-88, Standard Test Method for Volatile Alcohols in
Water by Direct Aqueous-Injection Gas Chromatography, IBR approved for
Sec. 63.365(e)(1) of Subpart O.
(11) ASTM D3792-91, Standard Method for Water Content of Water-
Reducible Paints by Direct Injection into a Gas Chromatograph, IBR
approved for Sec. 63.788, Appendix A.
(12) ASTM D3912-80, Standard Test Method for Chemical Resistance of
Coatings Used in Light-Water Nuclear Power Plants, IBR approved for
Sec. 63.782.
(13) ASTM D4017-90, 96a, Standard Test Method for Water in Paints
and Paint Materials by the Karl Fischer Titration Method, IBR approved
for Sec. 63.788, Appendix A.
(14) ASTM D4082-89, Standard Test Method for Effects of Gamma
Radiation on Coatings for Use in Light-Water Nuclear Power Plants, IBR
approved for Sec. 63.782.
(15) ASTM D4256-89, 94, Standard Test Method for Determination of
the Decontaminability of Coatings Used in Light-Water Nuclear Power
Plants, IBR approved for Sec. 63.782.
(16) ASTM D4809-95, Standard Test Method for Heat of Combustion of
Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method), IBR
approved for Sec. 63.11(b)(6).
(17) ASTM E180-93, Standard Practice for Determining the Precision
of ASTM Methods for Analysis and Testing of Industrial Chemicals, IBR
approved for Sec. 63.786(b).
(18) ASTM E260-91, 96, General Practice for Packed Column Gas
Chromatography, IBR approved for Secs. 63.750(b)(2) and 63.786(b)(5).
(19) [Reserved]
(20) [Reserved]
(21) ASTM D2099-00, Standard Test Method for Dynamic Water
Resistance of Shoe Upper Leather by the Maeser Water Penetration Tester,
IBR approved for Sec. 63.5350.
(22) [Reserved]
(23) [Reserved]
(24) ASTM D2697-86 (Reapproved 1998), ``Standard Test Method for
Volume Nonvolatile Matter in Clear or Pigmented Coatings,'' IBR approved
for Secs. 63.4141(b)(1) and 63.5160(c).
(25) ASTM D6093-97, ``Standard Test Method for Percent Volume
Nonvolatile Matter in Clear or Pigmented Coatings Using a Helium Gas
Pycnometer,'' IBR approved for Secs. 63.4141(b)(1), 63.4941(b)(1), and
63.5160(c).
(26) ASTM D1475-98, Standard Test Method for Density of Liquid
Coatings, Inks, and Related Products, IBR approved for
Secs. 63.4141(b)(3) and 63.4141(c).
(27) ASTM D 6522-00, Standard Test Method for Determination of
Nitrogen Oxides, Carbon Monoxide, and Oxygen Concentrations in Emissions
from Natural Gas Fired Reciprocating Engines, Combustion Turbines,
Boilers, and Process Heaters Using Portable Analyzers, IBR approved for
Sec. 63.9307(c)(2).
(28) [Reserved]
[[Page 63]]
(29) ASTM D6420-99, Standard Test Method for Determination of
Gaseous Organic Compounds by Direct Interface Gas Chromatography-Mass
Spectrometry, IBR approved for Secs. 63.5799 and 63.5850.
(c) The materials listed below are available for purchase from the
American Petroleum Institute (API), 1220 L Street, NW., Washington, DC
20005.
(1) API Publication 2517, Evaporative Loss from External Floating-
Roof Tanks, Third Edition, February 1989, IBR approved for Sec. 63.111
of subpart G of this part.
(2) API Publication 2518, Evaporative Loss from Fixed-roof Tanks,
Second Edition, October 1991, IBR approved for Sec. 63.150(g)(3)(i)(C)
of subpart G of this part.
(3) API Manual of Petroleum Measurement Specifications (MPMS)
Chapter 19.2, Evaporative Loss From Floating-Roof Tanks (formerly API
Publications 2517 and 2519), First Edition, April 1997, IBR approved for
Sec. 63.1251 of subpart GGG of this part.
(d) State and Local Requirements. The materials listed below are
available at the Air and Radiation Docket and Information Center, U.S.
EPA, 401 M St., SW., Washington, DC.
(1) California Regulatory Requirements Applicable to the Air Toxics
Program, January 5, 1999, IBR approved for Sec. 63.99(a)(5)(ii) of
subpart E of this part.
(2) New Jersey's Toxic Catastrophe Prevention Act Program, (July 20,
1998), Incorporation By Reference approved for Sec. 63.99 (a)(30)(i) of
subpart E of this part.
(3)(i) Letter of June 7, 1999 to the U.S. Environmental Protection
Agency Region 3 from the Delaware Department of Natural Resources and
Environmental Control requesting formal full delegation to take over
primary responsibility for implementation and enforcement of the
Chemical Accident Prevention Program under Section 112(r) of the Clean
Air Act Amendments of 1990.
(ii) Delaware Department of Natural Resources and Environmental
Control, Division of Air and Waste Management, Accidental Release
Prevention Regulation, sections 1 through 5 and sections 7 through 14,
effective January 11, 1999, IBR approved for Sec. 63.99(a)(8)(i) of
subpart E of this part.
(iii) State of Delaware Regulations Governing the Control of Air
Pollution (October 2000), IBR approved for Sec. 63.99(a)(8)(ii)-(v) of
subpart E of this part.
(4) Massachusetts Regulations Applicable to Hazardous Air Pollutants
(July 2002). Incorporation By Reference approved for
Sec. 63.99(a)(21)(ii) of subpart E of this part.
(e) The materials listed below are available for purchase from the
National Institute of Standards and Technology, Springfield, VA 22161,
(800) 553-6847.
(1) Handbook 44, Specificiations, Tolerances, and Other Technical
Requirements for Weighing and Measuring Devices 1998, IBR approved for
Sec. 63.1303(e)(3).
(2) [Reserved]
(f) The following material is available from the National Council of
the Paper Industry for Air and Stream Improvement, Inc. (NCASI), P. O.
Box 133318, Research Triangle Park, NC 27709-3318 or at http://
www.ncasi.org: NCASI Method DI/MEOH-94.02, Methanol in Process Liquids
GC/FID (Gas Chromatography/Flame Ionization Detection), August 1998,
Methods Manual, NCASI, Research Triangle Park, NC, IBR approved for
Sec. 63.457(c)(3)(ii) of subpart S of this part.
(g) The materials listed below are available for purchase from AOAC
International, Customer Services, Suite 400, 2200 Wilson Boulevard,
Arlington, Virginia, 22201-3301, Telephone (703) 522-3032, Fax (703)
522-5468.
(1) AOAC Official Method 978.01 Phosphorus (Total) in Fertilizers,
Automated Method, Sixteenth edition, 1995, IBR approved for
Sec. 63.626(d)(3)(vi).
(2) AOAC Official Method 969.02 Phosphorus (Total) in Fertilizers,
Alkalimetric Quinolinium Molybdophosphate Method, Sixteenth edition,
1995, IBR approved for Sec. 63.626(d)(3)(vi).
(3) AOAC Official Method 962.02 Phosphorus (Total) in Fertilizers,
Gravimetric Quinolinium Molybdophosphate Method, Sixteenth edition,
1995, IBR approved for Sec. 63.626(d)(3)(vi).
[[Page 64]]
(4) AOAC Official Method 957.02 Phosphorus (Total) in Fertilizers,
Preparation of Sample Solution, Sixteenth edition, 1995, IBR approved
for Sec. 63.626(d)(3)(vi).
(5) AOAC Official Method 929.01 Sampling of Solid Fertilizers,
Sixteenth edition, 1995, IBR approved for Sec. 63.626(d)(3)(vi).
(6) AOAC Official Method 929.02 Preparation of Fertilizer Sample,
Sixteenth edition, 1995, IBR approved for Sec. 63.626(d)(3)(vi).
(7) AOAC Official Method 958.01 Phosphorus (Total) in Fertilizers,
Spectrophotometric Molybdovanadophosphate Method, Sixteenth edition,
1995, IBR approved for Sec. 63.626(d)(3)(vi).
(h) The materials listed below are available for purchase from The
Association of Florida Phosphate Chemists, P.O. Box 1645, Bartow,
Florida, 33830, Book of Methods Used and Adopted By The Association of
Florida Phosphate Chemists, Seventh Edition 1991, IBR.
(1) Section IX, Methods of Analysis for Phosphate Rock, No. 1
Preparation of Sample, IBR approved for Sec. 63.606(c)(3)(ii) and
Sec. 63.626(c)(3)(ii).
(2) Section IX, Methods of Analysis for Phosphate Rock, No. 3
Phosphorus--P2O5 or
Ca3(PO4)2, Method A-Volumetric Method,
IBR approved for Sec. 63.606(c)(3)(ii) and Sec. 63.626(c)(3)(ii).
(3) Section IX, Methods of Analysis for Phosphate Rock, No. 3
Phosphorus-P2O5 or
Ca3(PO4)2, Method B--Gravimetric
Quimociac Method, IBR approved for Sec. 63.606(c)(3)(ii) and
Sec. 63.626(c)(3)(ii).
(4) Section IX, Methods of Analysis For Phosphate Rock, No. 3
Phosphorus-P2O5 or
Ca3(PO4)2, Method C--Spectrophotometric
Method, IBR approved for Sec. 63.606(c)(3)(ii) and
Sec. 63.626(c)(3)(ii).
(5) Section XI, Methods of Analysis for Phosphoric Acid,
Superphosphate, Triple Superphosphate, and Ammonium Phosphates, No. 3
Total Phosphorus-P2O5, Method A--Volumetric
Method, IBR approved for Sec. 63.606(c)(3)(ii), Sec. 63.626(c)(3)(ii),
and Sec. 63.626(d)(3)(v).
(6) Section XI, Methods of Analysis for Phosphoric Acid,
Superphosphate, Triple Superphosphate, and Ammonium Phosphates, No. 3
Total Phosphorus-P2O5, Method B--Gravimetric
Quimociac Method, IBR approved for Sec. 63.606(c)(3)(ii),
Sec. 63.626(c)(3)(ii), and Sec. 63.626(d)(3)(v).
(7) Section XI, Methods of Analysis for Phosphoric Acid,
Superphosphate, Triple Superphosphate, and Ammonium Phosphates, No. 3
Total Phosphorus-P2O5, Method C--
Spectrophotometric Method, IBR approved for Sec. 63.606(c)(3)(ii),
Sec. 63.626(c)(3)(ii), and Sec. 63.626(d)(3)(v).
(i) The following materials are available for purchase from at least
one of the following addresses: ASME International, Orders/Inquiries,
P.O. Box 2900, Fairfield, NJ 07007-2900; or Global Engineering
Documents, Sales Department, 15 Inverness Way East, Englewood, CO 80112.
(1) ASME standard number QHO-1-1994, ``Standard for the
Qualification and Certification of Hazardous Waste Incinerator
Operators,'' IBR approved for Sec. 63.1206(c)(6)(iii).
(2) ASME standard number QHO-1a-1996 Addenda to QHO-1-1994,
``Standard for the Qualification and Certification of Hazardous Waste
Incinerator Operators,'' IBR approved for Sec. 63.1206(c)(6)(iii).
(3) ANSI/ASME PTC 19.10-1981, ``Flue and Exhaust Gas Analyses [Part
10, Instruments and Apparatus],'' IBR approved for Secs. 63.865(b),
63.3360(e)(1)(iii), 63.4166(a)(3), 63.4965(a)(3), and
53.5160(d)(1)(iii).
(j) [Reserved]
(k) The following material may be obtained from U.S. EPA, Office of
Solid Waste (5305W), 1200 Pennsylvania Avenue, NW., Washington, DC
20460:
(1) Method 9071B, ``n-Hexane Extractable Material(HEM) for Sludge,
Sediment, and Solid Samples,'' (Revision 2, April 1998) as published in
EPA Publication SW-846: ``Test Methods for Evaluating Solid Waste,
Physical/Chemical Methods.'' The incorporation by reference of Method
9071B is approved for Section 63.7824(e) of Subpart FFFFF of this part.
[59 FR 12430, Mar. 16, 1994]
Editorial Note: Federal Register citations affecting Sec. 63.14, see
the List of CFR Sections Affected, which appears in the Finding Aids
section of the printed volume and on GPO Access.
[[Page 65]]
Effective Date Note: At 68 FR 31615, May 28, 2003, Sec. 63.14 was
amended by adding paragraph (d)(5) effective July 28, 2003. For the
convenience of the user, the added text is set forth as follows.
Sec. 63.14 Incorporation by reference.
* * * * *
(d) * * *
(5) New Hampshire Regulations Applicable to Hazardous Air
Pollutants, March, 2003. Incorporation by Reference approved for
Sec. 63.99(a)(29)(iii) of subpart E of this part.
* * * * *