[Code of Federal Regulations] [Title 48, Volume 1] [Revised as of October 1, 2003] From the U.S. Government Printing Office via GPO Access [CITE: 48CFR19.102] [Page 337-339] TITLE 48--FEDERAL ACQUISITION REGULATIONS SYSTEM CHAPTER 1--FEDERAL ACQUISITION REGULATION PART 19_SMALL BUSINESS PROGRAMS--Table of Contents Subpart 19.1_Size Standards Sec. 19.102 Size standards. (a) The SBA establishes small business size standards on an industry-by-industry basis. (See 13 CFR part 121.) (b) Small business size standards are applied by-- (1) Classifying the product or service being acquired in the industry whose definition, as found in the North American Industry Classification System (NAICS) Manual (available via the Internet at http://www.census.gov/epcd/www/naics.html), best describes the principal nature of the product or service being acquired; (2) Identifying the size standard SBA established for that industry; and (3) Specifying the size standard in the solicitation, so that offerors can appropriately represent themselves as small or large. (c) For size standard purposes, a product or service shall be classified in only one industry, whose definition best describes the principal nature of [[Page 338]] the product or service being acquired even though for other purposes it could be classified in more than one. (d) When acquiring a product or service that could be classified in two or more industries with different size standards, contracting officers shall apply the size standard for the industry accounting for the greatest percentage of the contract price. (e) If a solicitation calls for more than one item and allows offers to be submitted on any or all of the items, an offeror must meet the size standard for each item it offers to furnish. If a solicitation calling for more than one item requires offers on all or none of the items, an offeror may qualify as a small business by meeting the size standard for the item accounting for the greatest percentage of the total contract price. (f) Any concern submitting a bid or offer in its own name, other than on a construction or service contract, that proposes to furnish an end product it did not manufacture (a ``nonmanufacturer''), is a small business if it has no more than 500 employees, and-- (1) Except as provided in paragraphs (f)(4) through (f)(7) of this section, in the case of Government acquisitions set-aside for small businesses, furnishes in the performance of the contract, the product of a small business manufacturer or producer. The end product furnished must be manufactured or produced in the United States or its outlying areas. The term ``nonmanufacturer'' includes a concern that can, but elects not to, manufacture or produce the end product for the specific acquisition. For size determination purposes, there can be only one manufacturer of the end product being acquired. The manufacturer of the end product being acquired is the concern that, with its own forces, transforms inorganic or organic substances including raw materials and/ or miscellaneous parts or components into the end product. However, see the limitations on subcontracting at 52.219-14 that apply to any small business offeror other than a nonmanufacturer for purposes of set-asides and 8(a) awards. (2) A concern which purchases items and packages them into a kit is considered to be a nonmanufacturer small business and can qualify as such for a given acquisition if it meets the size qualifications of a small nonmanufacturer for the acquisition, and if more than 50 percent of the total value of the kit and its contents is accounted for by items manufactured by small business. (3) For the purpose of receiving a Certificate of Competency on an unrestricted acquisition, a small business nonmanufacturer may furnish any domestically produced or manufactured product. (4) In the case of acquisitions set aside for small business or awarded under section 8(a) of the Small Business Act, when the acquisition is for a specific product (or a product in a class of products) for which the SBA has determined that there are no small business manufacturers or processors in the Federal market, then the SBA may grant a class waiver so that a nonmanufacturer does not have to furnish the product of a small business. For the most current listing of classes for which SBA has granted a waiver, contact an SBA Office of Government Contracting. A listing is also available on SBA's Internet Homepage at http://www.sba.gov/gc. Contracting officers may request that the SBA waive the nonmanufacturer rule for a particular class of products. (5) For a specific solicitation, a contracting officer may request a waiver of that part of the nonmanufacturer rule which requires that the actual manufacturer or processor be a small business concern if the contracting officer determines that no known domestic small business manufacturers or processors can reasonably be expected to offer a product meeting the requirements of the solicitation. (6) Requests for waivers shall be sent to the Associate Administrator for Government Contracting, United States Small Business Administration, Mail Code 6250, 409 Third Street, SW., Washington, DC 20416. (7) The SBA provides for an exception to the nonmanufacturer rule if-- (i) The procurement of a manufactured end product processed under the procedures set forth in part 13-- (A) Is set aside for small business; and [[Page 339]] (B) Is not anticipated to exceed $25,000; and (ii) The offeror supplies an end product that is manufactured or produced in the United States or its outlying areas. (g) In the case of acquisitions set aside for very small business in accordance with 19.904, offerors may not have more than 15 employees and may not have average annual receipts that exceed $1 million. (h) The industry size standards are published by the Small Business Administration and are available via the Internet at http://www.sba.gov/ size. [48 FR 42240, Sept. 19, 1983 as amended at 51 FR 2652, Jan. 17, 1986; 51 FR 27489, July 31, 1986; 51 FR 31426, Sept. 3, 1986; 52 FR 21887, June 9, 1987; 52 FR 30076, Aug. 12, 1987; 53 FR 661, Jan. 11, 1988; 53 FR 34227, Sept. 2, 1988; 53 FR 43390, Oct. 26, 1988; 54 FR 5055, Jan. 31, 1989; 54 FR 13023, Mar. 29, 1989; 54 FR 25062, June 12, 1989; 55 FR 3882, Feb. 5, 1990; 55 FR 25529, June 21, 1990; 57 FR 60580, 60610, Dec. 21, 1992; 59 FR 11376, 11387, Mar. 10, 1994; 59 FR 17723, Apr. 14, 1994; 60 FR 34756, July 3, 1995; 61 FR 31622, June 20, 1996; 61 FR 39208, July 26, 1996; 61 FR 67410, Dec. 20, 1996; 63 FR 58602, Oct. 30, 1998; 63 FR 70292, Dec. 18, 1998; 64 FR 10536, Mar. 4, 1999; 64 FR 51850, Sept. 24, 1999; 65 FR 46056, July 26, 2000; 66 FR 65370, Dec. 18, 2001; 68 FR 28081, May 22, 2003]