[Code of Federal Regulations] [Title 49, Volume 2] [Revised as of October 1, 2003] From the U.S. Government Printing Office via GPO Access [CITE: 49CFR171.7] [Page 78-84] TITLE 49--TRANSPORTATION CHAPTER I--RESEARCH AND SPECIAL PROGRAMS ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PART 171_GENERAL INFORMATION, REGULATIONS, AND DEFINITIONS--Table of Contents Sec. 171.7 Reference material. (a) Matter incorporated by reference--(1) General. There is incorporated, by reference in parts 170-189 of this subchapter, matter referred to that is not specifically set forth. This matter is hereby made a part of the regulations in parts 170-189 of this subchapter. The matter subject to change is incorporated only as it is in effect on the date of issuance of the regulation referring to that matter. The material listed in paragraph (a)(3) has been approved for incorporation by reference by the Director of the Federal Register in accordance with 5 U.S.C 552(a) and 1 CFR part 51. Material is incorporated as it exists on the date of the approval and a notice of any change in the material will be published in the Federal Register. Matters referenced by footnote are included as part of the regulations of this subchapter. (2) Accessibility of materials. All incorporated matter is available for inspection at: (i) The Office of Hazardous Materials Safety, Office of Hazardous Materials Standards, Room 8422, NASSIF Building, 400 7th Street, SW., Washington, DC 20590; and (ii) The Office of the Federal Register, 800 North Capitol Street, NW., suite 700, Washington, DC. (3) Table of material incorporated by reference. The following table sets forth material incorporated by reference. The first column lists the name and address of the organization from which the material is available and the name of the material. The second column lists the section(s) of this subchapter, other than Sec. 171.7, in which the matter is referenced. The second column is presented for information only and may not be all inclusive. [[Page 79]] ------------------------------------------------------------------------ Source and name of material 49 CFR reference ------------------------------------------------------------------------ Air Transport Association of America, 1301 Pennsylvania Avenue, N.W., Washington, DC 20004-1707 ATA Specification No. 300 Packaging of Airline 172.102 Supplies, Revision 19, July 31, 1996. The Aluminum Association, 420 Lexington Avenue, New York, NY 10017 Aluminum Standards and Data, Seventh Edition, 172.102; 178..46 and June 1982. 178.65 American National Standards Institute, Inc., 25 West 43rd Street, New York, NY 10036 American Petroleum Institute, 1220 L Street, NW, Washington, D.C. 20005-4070: API Recommended Practice 1604 Closures of 172.102 Underground Petroleum Storage Tanks, 3rd Edition, March 1996 ANSI/ASHRAE 15-94, Safety Code for Mechanical 173.306 Refrigeration. ANSI B16.5-77, Steel Pipe Flanges, Flanged 178.345; 178.360 Fittings. ANSI N14.1 Uranium Hexafluoride--Packaging for 173.417; 173.420 Transport, 1971, 1982, 1987, 1990, 1995 and 2001 Editions.. American Pyrotechnics Association (APA), P.O. Box 213, Chestertown, MD 21620 APA Standard 87-1, Standard for Construction and 173.56 Approval for Transportation of Fireworks, Novelties, and Theatrical Pyrotechnics, December 1, 2001 version. American Society of Mechanical Engineers, ASME International, 22 Law Drive, P.O. Box 2900, Fairfield, NJ 07007-2900 ASME Code, Sections II (Parts A and B), V, VIII 173.32; 173.306; (Division 1), and IX of 1998 Edition of 173.315; 173.318; American Society of Mechanical Engineers Boiler 173.420; 178.245; and Pressure Vessel Code. 178.255; 178.270; 178.271; 178.272; 178.337; 178.338; 178.345; 178.346; 178.347; 178.348; 179.400; 180.407; 180.417 ASME Code, Section V (FR Nondestructive 180.407 Examination), 1977. ASME Code, Section IX (FR Welding and Brazing 178.245; 178.270; Qualification), 1977 and Addendum (1979). 178.337; 178.338 American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 19428 Noncurrent ASTM Standards are available from: Engineering Societies Library, 354 E. 47th Street, New York, NY 10017 ASTM A 20/A 20M-93a Standard Specification for 178.337-2; 179.102-4; General Requirements for Steel Plates for 179.102-17. Pressure Vessels. ASTM A 47-68 Malleable Iron Castings............ 179.200 ASTM A 240/A 240M-99b Standard Specification for 178.57; 178.358-5; Heat-Resisting Chromium and Chromium-Nickel 179.100-7; 179.100- Stainless Steel Plate, Sheet and Strip for 10; 179.102-1; Pressure Vessels. 179.102-4; 179.102- 17; 179.200-7; 179.201-5; 179.220-7; 179.400-5. ASTM A 242-81 Standard Specification for High- 179.100 Strength Low-Alloy Structural Steel. ASTM A 262-93a Standard Practices for Detecting 179.100-7; 179.200-7; Susceptibility to Intergranular Attack in 179.201-4. Austenitic Stainless Steels. ASTM A 300-58 Steel Plates for Pressure Vessels 178.337 for Service at Low Temperatures. ASTM A 302/A 302M-93 Standard Specification for 179.100-7; 179.200-7; Pressure Vessel Plates, Alloy Steel, Manganese- 179.220-7. Molybdenum and Manganese-Molybdenum Nickel. ASTM A 333-67 Seamless and Welded Steel Pipe for 178.45 Low-Temperature Service. ASTM A 366/A 366M-91 (1993)e1 Standard 178.601 Specification for Steel, Sheet, Carbon, Cold- Rolled, Commercial Quality. ASTM A 370-94 Standard Test Methods and 179.102-1; 179.102-4; Definitions for Mechanical Testing of Steel 179.102-17. Products. ASTM A 441-81 Standard Specification for High- 178.338 Strength Low-Alloy Structural Manganese Vanadium Steel. ASTM A 514-81 Standard Specification for High- 178.338 Yield Strength Quenched and Tempered Alloy Steel Plate, Suitable for Welding. [[Page 80]] ASTM A 516/A 516M-90 Standard Specification for 178.337-2; 179.100-7; Pressure Vessel Plates, Carbon Steel, for 179.100-20; 179.102- Moderate and Lower- Temperature Service. 1; 179.102-2; 179.102- 4; 179.102-17; 179.200-7; 179.220-7. ASTM A 537/A 537M-91 Standard Specification for 179.100-7; 179.102-4; Pressure Vessel Plates, Heat-Treated, Carbon- 179.102-17. Manganese-Silicon Steel. ASTM A 568/A 568M-95 Standard Specification for 178.601 Steel, Sheet, Carbon, and High-Strength, Low- Alloy, Hot-Rolled and Cold-Rolled, General Requirements for. ASTM A 572-82 Standard Specification for High- 178.338; 179.100 Strength Low-Alloy Columbian-Vanadium Steels of Structural Quality. ASTM A 588-81 Standard Specification for High- 179.100; 178.338 Strength Low-Alloy Structural Steel with 50 Ksi Minimum Yield Point to 4 in. Thick. ASTM A 606-75 Standard Specification for Steel 178.338 Sheet and Strip Hot-Rolled and Cold-Rolled, High-Strength, Low-Alloy, with Improved Atmospheric Corrosion Resistance, 1975 (Reapproved 1981). ASTM A 612-72a High Strength Steel Plates for 178.337 Pressure Vessels for Moderate and Lower Temperature Service. ASTM A 633-79a Standard Specification for 178.338 Normalized High-Strength Low-Alloy Structural Steel, 1979 Edition. ASTM A 715-81 Standard Specification for Steel 178.338 Sheet and Strip, Hot-Rolled, High-Strength, Low- Alloy with Improved Formability, 1981. ASTM B 162-93a Standard Specification for Nickel 179.200-7. Plate, Sheet, and Strip. ASTM B 209-93 Standard Specification for 179.100-7; 179.200-7; Aluminum and Aluminum-Alloy Sheet and Plate. 179.220-7. ASTM B 557-84 Tension Testing Wrought and Cast 178.46. Aluminum and Magnesium-Alloy Products. ASTM B 580-79 Standard Specification for Anodic 173.316; 173.318; Oxide Coatings on Aluminum, (Re-approved 2000). 178.338-17 ASTM D 56-97a Standard Test Method for Flash 173.120 Point by Tag Closed Tester. ASTM D 93-97 Standard Test Methods for Flash 173.120 Point by Pensky-Martens Closed Cup Tester. ASTM D 445-88 Kinematic Viscosity of Transparent 171.8 and Opaque Liquids (and the Calculation of Dynamic Viscosity). ASTM D 1200-88 Viscosity by Ford Viscosity Cup.. 171.8 ASTM D 1709-01 Standard Test Methods for Impact 173.197 Resistance of Plastic Film by the Free-Falling Dart Method. ASTM D 1835-97 Standard Specification for 180.209 Liquefied Petroleum (LP) Gases. ASTM D 1838-64 Copper Strip Corrosion by 173.315 Liquefied Petroleum (LP) Gases. ASTM D 1922-00a Standard Test Method for 173.197 Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method. ASTM D 3278-96 Standard Test Methods for Flash 173.120 Point of Liquids by Small Scale Closed-Cup Apparatus. ASTM D 3828-97, Standard Test Methods for Flash 173.120. Point by Small Scale Closed Tester. ASTM D 4206-96 Standard Test Method for 173.120. Sustained Burning of Liquid Mixtures Using the Small Scale Open-Cup Apparatus. ASTM D 4359-90 Standard Test Method for 171.8 Determining Whether a Material is a Liquid or a Solid. ASTM E 8-99 Standard Test Methods for Tension 178.36; 178.37; Testing of Metallic Materials. 178.38; 178.39; 178.44; 178.45; 178.50; 178.51; 178.53; 178.55; 178.56; 178.57; 178.58; 178.59; 178.60; 178.61; 178.68. ASTM E 23-98 Standard Test Methods for Notched 178.57 Bar Impact Testing of Metallic Materials. ASTM E 112-88 Standard Test Methods for 178.44. Determining Average Grain Size. ASTM E 112-96 Standard Test Methods for 178.274 Determining Average Grain Size, 1996 Edition. ASTM E 213-98 Standard Practice for Ultrasonic 178.45 Examination of Metal Pipe and Tubing. ASTM E 114-95 Standard Practice for Ultrasonic 178.45 Pulse-Echo Straight-Beam Examination by the Contact Method. ASTM E 290-92 Standard Test Method for Semi- 178.46. Guided Bend Test for Ductility of Metallic Materials. ASTM E 681-85 Standard Test Method for 173.115 Concentration Limits of Flammability of Chemicals. ASTM G 23-69 Standard Recommended Practice for 172.407; 172.519 Operating Light-and-Water Exposure Apparatus (Carbon-Arc Type) for Exposure of Nonmetallic Materials. ASTM G 26-70 Standard Recommended Practice for 172.407; 172.519 Operating Light-and-Water Exposure Apparatus (Xenon-Arc-Type) for Exposure of Nonmetallic Materials. ASTM G 31-72 (Reapproved 1995) Standard Practice 173.137 for Laboratory Immersion Corrosion Testing of Metals. [[Page 81]] American Water Works Association, 1010 Vermont Avenue, NW., Suite 810, Washington, DC 20005 AWWA Standard C207-55, Steel Pipe Flanges, 1955. 178.360 American Welding Society, 550 N. W. Le Jeune Road, Miami, Florida 33126 AWS Code B 3.0; Standard Qualification 178.356 Procedure; 1972 (FRB 3.0-41, rev. May 1973). AWS Code D 1.0; Code for Welding in Building 178.356 Construction (FR D 1.0-66). Association of American Railroads, American Railroads Building, 50 F Street, NW., Washington, DC 20001 AAR Manual of Standards and Recommended 173.31, 174.63, 179.6, Practices, Section C--Part III, Specifications 179.7, 179.12, for Tank Cars, Specification M-1002, December 179.15, 179.16, 2000. 179.20, 179.22, 179.100, 179.101, 179.102, 179.103, 179.200, 179.201, 179.220, 179.300, 179.400, 180.509, 180.513, 180.515, 180.517. AAR Manual of Standards and Recommended 174.55; 174.63. Practices, Section I, Specially Equipped Freight Car and Intermodal Equipment, 1988. AAR Specifications for Design, Fabrication and 179.16. Construction of Freight Cars, Volume 1, 1988. Chlorine Institute, Inc., 2001 L Street, NW., Suite 506, Washington, DC 20036 Chlorine Institute Emergency Kit ``A'' for 100- 173.3 lb. & 150-lb. Chlorine Cylinders (with the exception of repair method using Device 8 for side leaks), Edition 9, June 2000. Chlorine Institute Emergency Kit ``B'' for 173.3 Chlorine Ton Containers (with the exception of repair method using Device 9 for side leaks) Edition 8, June 1996. Type 1\1/2\ JQ 225, Dwg, H51970, Revision D, 173.315 April 5, 1989; or Type 1\1/2\ JQ 225, Dwg. H50155, Revision F, April 4, 1989. Section 3, Pamphlet 57, Emergency Shut-Off 177.840 Systems for Bulk Transfer of Chlorine, 3rd Edition, October 1997. Standard Chlorine Angle Valve Assembly, Dwg. 104- 178.337-9 8, July 1993. Excess Flow Valve with Removable Seat, Dwg. 101- 178.337-8 7, July 1993. Excess Flow Valve with Removable Basket, Dwg. 178.337-8 106-6, July 1993. Standards for Housing and Manway Covers for 178.337-10 Steel Cargo Tanks, Dwg. 137-3, September 1, 1982. Compressed Gas Association, Inc., 4221 Walney Road, 5th Floor, Chantilly, Virginia 20151 CGA Pamphlet C-3, Standards for Welding on Thin- 178.47; 178.50; Walled Steel Cylinders, 1994. 178.51; 178.53; 178.56; 178.57; 178.58; 178.59; 178.60; 178.61; 178.65; 178.68; 180.211. CGA Pamphlet C-5, Cylinder Service Life-- 173.302a Seamless Steel High Pressure Cylinders, 1991. CGA Pamphlet C-6, Standards for Visual 173.198; 180.205; Inspection of Steel Compressed Gas Cylinders, 180.209; 180.211; 1993. 180.519. CGA Pamphlet C-6.1, Standards for Visual 180.205; 180.209 Inspection of High Pressure Aluminum Compressed Gas Cylinders, 1995. CGA Pamphlet C-6.2, Guidelines for Visual 180.205 Inspection and Requalification of Fiber Reinforced High Pressure Cylinders, 1996, Third Edition. CGA Pamphlet C-6.3, Guidelines for Visual 180.205; 180.209 Inspection and Requalification of Low Pressure Aluminum Compressed Gas Cylinders, 1991. CGA Pamphlet C-7, A Guide for the Preparation of 172.400a Precautionary Markings for Compressed Gas Containers, appendix A, issued 1992 (6th Edition). CGA Pamphlet C-8, Standard for Requalification 180.205 of DOT-3HT Cylinder Design, 1985. CGA Pamphlet C-11, Recommended Practices for 178.35 Inspection of Compressed Gas Cylinders at Time of Manufacture, 2001, Third Edition. CGA Pamphlet C-12, Qualification Procedure for 173.301; 173.303; Acetylene Cylinder Design, 1994. 178.59; 178.60. CGA Pamphlet C-13, Guidelines for Periodic 173.303, 180.205, Visual Inspection and Requalification of 180.209 Acetylene Cylinders, 2000, Fourth Edition. CGA Pamphlet C-14, Procedures for Fire Testing 173.301 of DOT Cylinder Pressure Relief Device Systems, 1979. CGA Pamphlet G-2.2 Tentative Standard Method for 173.315 Determining Minimum of 0.2% Water in Anhydrous Ammonia, 1985. CGA Pamphlet G-4.1, Cleaning Equipment for 178.338 Oxygen Service, 1985. CGA Pamphlet P-20, Standard for the 173.115 Classification of Toxic Gas Mixtures, 1995. CGA Pamphlet S-1.1, Pressure Relief Device 173.301, 173.304a Standards--Part 1--Cylinders for Compressed Gases, 2001 (with the exception of paragraph 9.1.1.1), Ninth Edition. [[Page 82]] CGA Pamphlet S-1.2, Safety Relief Device 173.315; 173.318 Standards Part 2--Cargo and Portable Tanks for Compressed Gases, 1980. CGA Pamphlet S-7, Method for Selecting Pressure 173.301 Relief Devices for Compressed Gas Mixtures in Cylinders, 1996. CGA Technical Bulletin TB-2, Guidelines for 180.413 Inspection and Repair of MC-330 and MC-331 Cargo Tanks, 1980. Department of Defense (DOD), 2461 Eisenhower Avenue, Alexandria, VA 22331 DOD TB 700-2; NAVSEAINST 8020.8B; AFTO 11A-1-47; 173.56 DLAR 8220.1: Explosives Hazard Classification Procedures, January 1998. Department of Energy (USDOE), 100 Independence Avenue SW., Washington, DC 20545 USDOE publications available from: Superintendent of Documents, Government Printing Office (GPO) or The National Technical Information Service (NTIS). USDOE, CAPE-1662, Revision 1, and Supplement 1, 178.356; 178.358 Civilian Application Program Engineering Drawings. USDOE, Material and Equipment Specification No. 178.356; 178.358 SP-9, Rev. 1, and Supplement--Fire Resistant Phenolic Foam. USDOE, ORO 651--Uranium Hexafloride; A Manual of 173.417 Good Practices, Revision 6, 1991 edition. USDOE, KSS-471, November 30, 1986--Proposal for 178.358 Modifications to U.S. Department of Transportation Specification 21PF-1, Fire and Shock Resistant Phenolic Foam--Insulated Metal Overpack. General Services Administration, Specification Office, Rm. 6662, 7th and D Street, SW., Washington, DC 20407 Federal Specification RR-C-901C, Cylinders, 173.302; 173.336; Compressed Gas: High Pressure Steel DOT 3AA, 173.337 and Aluminum Applications, January 15, 1981 (Superseding RR-C-901B, August 1, 1967). Health and Human Services Centers for Disease Control and Prevention, 1600 Clifton Road N.E., Atlanta GA 30333 Also available from: Superintendent of 173.134 Documents, Government Printing Office (GPO), HHS Publication No. (CDC) 93-8395, Biosafety in Microbiological and Biomedical Laboratories, 3rd Edition, May 1993, Section II Institute of Makers of Explosives, 1120 19th Street, Suite 310, Washington, DC 20036-3605 IME Safety Library Publication No. 22 (IME 173.63, 177.835 Standard 22), Recommendation for the Safe Transportation of Detonators in a Vehicle with Certain Other Explosive Materials, May 1993. International Atomic Energy Agency (IAEA), P.O. Box 100, Wagramer Strasse 5, A-1400 Vienna, Austria Also available from: Bernan Associates, 4611-F Assembly Drive, Lanham, MD 20706-4391, USA; or Renouf Publishing Company, Ltd., 812 Proctor Avenue, Ogdensburg, New York 13669, USA IAEA, Regulations for the Safe Transport of 171.12 Radioactive Material, No. TS-R-1, 1996 Edition (Revised), (ST-1, Revised). IAEA, Regulations for the Safe Transport of 171.12; 173.415; Radioactive Material, Safety Series No. 6, 1985 173.416; 173.417; Edition (as Amended 1990). 173.473 International Civil Aviation Organization (ICAO), P.O. Box 400, Place de l'Aviation Internationale, 1000 Sherbrooke Street West, Montreal, Quebec, Canada H3A 2R2 ICAO Technical Instructions available from: INTEREG, International Regulations, Publishing and Distribution Organization, P.O. Box 60105, Chicago, IL 60660 Technical Instructions for the Safe Transport of 171.11; 172.202; Dangerous Goods by Air (ICAO Technical 172.401; 172.512; Instructions), DOC 9284-AN/905, 2003-2004 172.602 Edition, including Erratum. International Maritime Organization (IMO), 4 Albert Embankment, London, SE17SR, United Kingdom or New York Nautical Instrument & Service Corporation, 140 W. Broadway, New York, NY 10013 International Convention for the Safety of Life 176.63 at Sea, (SOLAS) Amendments 2000, Chapter II-2/ Regulation 19, 2001.. International Maritime Dangerous Goods (IMDG) 171.12; 172.401; Code, 2000 edition, including Amendment 30-00 172.502; 173.21; (English edition). 176.2; 176.5; 176.11; 176.27; 176.30. International Maritime Dangerous Goods (IMDG 171.12; 172.202; Code), 2002 Edition, including Amendment 31-02 172.401; 172.502; (English Edition). 172.602; 173.21; 176.2; 176.5; 176.11; 176.27; 176.30 International Organization for Standardization, Case Postale 56, CH-1211, Geneve 20, Switzerland Also available from: ANSI 25 West 43rd Street, New York, NY 10036 ISO-82-1974(E) Steels Tensile Testing........... 178.270-3 ISO 535-1991(E) Paper and board--Determination 178.516 of water absorptiveness--Cobb method. ISO 1496-3 Series 1 freight containers-- 178.274 Specification and testing, Part 3: Tank containers for liquids, gases and pressurized dry bulk, March 1, 1995, Fourth Edition. [[Page 83]] ISO 1496-3-1995(E) - Series 1 Freight 173.411 Containers--Specification and Testing--Part 3: Tank Containers for Liquids, Gases and Pressurized Dry Bulk. ISO-2431-1984(E) Standard Cup Method............ 173.121 ISO 2592-1973(E) Petroleum products-- 173.120 Determination of flash and fire points-- Cleveland open cup method. ISO 2919-1980(E) - Sealed radioactive sources-- 173.469 Classification. ISO 3036-1975(E) Board--Determination of 178.708 puncture resistance. ISO 3574-1986(E) Cold-reduced carbon steel sheet 178.503 of commercial and drawing qualities. ISO 4126-1 Safety valves--Part 1: General Requirements, December 15, 1991, 178.274 First Edition. ISO/TR 4826-1979(E) - Sealed radioactive 173.469 sources--Leak test methods. ISO 6892 Metallic materials--Tensile testing, 178.274 July 15, 1984, First Edition. ISO 8115 Cotton bales--Dimensions and density, 172.102 1986 Edition. ISO 9328-1--1991(E) Steel plates and strips for 173.137 pressure purposes--Technical delivery conditions--Part 1: General requirements. National Board of Boiler and Pressure Vessel Inspectors, 1055 Crupper Avenue, Columbus, Ohio 43229 National Board Inspection Code, A Manual for 180.413 Boiler and Pressure Vessel Inspectors, NB-23, 1992 Edition. National Fire Protection Association, Batterymarch Park, Quincy, MA 02269 NFPA 58-Liquefied Petroleum Gas Code, 2001 173.315 Edition. National Institute of Standards and Technology, Department of Commerce, 5285 Port Royal Road, Springfield, VA 22151 USDC, NBS Handbook H-28 (1957), 1957 Handbook of 178.45, 178.46 Screw-Thread Standards for Federal Services, Part II, December 1966 Edition. National Motor Freight Traffic Association, Inc., Agent 1616 P Street, NW., Washington, DC 20036 National Motor Freight Classification NMF 100-I, 177.841 1982. Organization for Economic Cooperation and Development (OECD) OECD Publications and Information Center, 2001 L Street, Suite 700, Washington, DC 20036 OECD Guideline for Testing of Chemicals, No.404 173.137 ``Acute Dermal Irritation/Corrosion'', 1992. Transport Canada, TDG Canadian Government Publishing Center, Supply and Services, Canada, Ottawa, Ontario, Canada K1A 059. Transportation of Dangerous Goods Regulations, 1 171.12a; 172.401; July 1985, SOR/85/77, incorporating the 172.502. following Registration Numbers: SOR/85-314, SOR/ 85-585, SOR/85-609, SOR/86-526, SOR/88-635, SOR/ 87-335, SOR/87-186, SOR/89-39, SOR/89-294, SOR/ 90-847, SOR/91-711, SOR/91-712, SOR/92-447, SOR/ 92-600, SOR/93-203, SOR/93-274, SOR/93-525, SOR/ 94-146 and SOR/94-264 (English edition), SOR/95- 241, and SOR/95-547. Truck Trailer Manufacturers Association, 1020 Princess Street, Alexandria, Virginia 22314 TTMA RP No. 61-98, Performance of manhole and/or 180.405(g) Fill Opening Assemblies on MC 306, DOT 406, Non- ASME MC 312 and Non-ASME DOT 412 Cargo Tanks, June 1, 1998. TTMA RP No. 81, Performance of Spring Loaded 178.345-10 Pressure Relief Valves on MC 306, MC 307, and MC 312 Tanks, May 24, 1989 Edition. TTMA RP No. 81-97, Performance of Spring Loaded 178.345-10 Pressure Relief Valves on MC 306, MC 307, MC 312, DOT 406, DOT 407, and DOT 412 Tanks, July 1, 1997 Edition. TTMA TB No. 107, Procedure for Testing In- 180.405(g) Service Unmarked and/or Uncertified MC 306 and Non-ASME MC 312 Type Cargo Tank Manhole Covers, June 1, 1998. Edition. United Nations, United Nations Sales Section, New York, NY 10017 UN Recommendations on the Transport of Dangerous 172.202; 172.401; Goods, Twelfth Revised Edition (2001). 172.502; 173.24 UN Recommendations on the Transport of Dangerous 172.102; 173.21; Goods, Manual of Tests and Criteria, Third 173.56; 173.57; Revised Edition (1999). 173.124; 173.128; 173.166; 173.185. ------------------------------------------------------------------------ (b) List of informational materials not requiring incorporation by reference. The materials listed in this paragraph do not require approval for incorporation by reference and are included for informational purposes. These materials may be used as noted in those sections in which the material is referenced. ------------------------------------------------------------------------ Source and name of material 49 CFR reference ------------------------------------------------------------------------ American Biological Safety Association 1202 Allanson Road, Mundelein, IL 60060 Risk Group Classification for Infectious Agents, 173.134 1998. [[Page 84]] Association of American Railroads, American Railroads Building, 50 F Street, NW., Washington, DC 20001 AAR Catalog Nos. SE60CHT; SE60CC; SE60CHTE; 179.14 SE60CE; SE60DC; SE60DE. AAR Catalog Nos. SE67CC; SE67CE; SE67BHT; 179.14 SE67BC; SE67BHTE; SE67BE. AAR Catalog Nos. SE68BHT; SE68BC; SE68BHTE; 179.14 SE68BE. AAR Catalog Nos. SE69AHTE; SE69AE............... 179.14 AAR Catalog Nos. SF70CHT; SF70CC; SF70CHTE; 179.14 SF70CE. AAR Catalog Nos. SF73AC; SF73AE; SF73AHT; 179.14 SF73AHTE. AAR Catalog Nos. SF79CHT; SF79CC; SF79CHTE; 179.14 SF79CE. Bureau of Explosives, Hazardous Materials Systems (BOE), Association of American Railroads, American Railroads Building, 50 F Street, NW., Washington, DC 20001 Fetterley's Formula (The Determination of the 173.315 Relief Dimensions for Safety Valves on Containers in which Liquefied gas is charged and when the exterior surface of the container is exposed to a temperature of 1,200 [deg]F.). Pamphlet 6, Illustrating Methods for Loading and 174.55; 174.101; Bracing Carload and Less-Than-Carload Shipments 174.112; 174.115; of Explosives and Other Dangerous Articles, 174.290 1962. Pamphlet 6A (includes appendix No. 1, October 174.101; 174.290 1944 and appendix 2, December 1945), Illustrating Methods for Loading and Bracing Carload and Less-Than-Carload Shipments of Loaded Projectiles, Loaded Bombs, etc., 1943. Pamphlet 6C, Illustrating Methods for Loading 174.55; 174.63; and Bracing Trailers and Less-Than-Trailer 174.101; 174.112; Shipments of Explosives and Other Dangerous 174.115 Articles Via Trailer-on-Flatcar (TOFC) or Container-on-Flatcar (COFC), 1985. Emergency Handling of Hazardous Materials in 171.7 Surface Transportation, 1989. Centers for Disease Control and Prevention 1600 Clifton Road, Atlanta, GA 30333 Biosafety in Microbiological and Biomedical 173.134 Laboratories, Fourth Edition, April 1999. National Association of Corrosion Engineers, 1440 South Creek, Houston, Texas 77084 NACE Standard TM-01-69, Test Method Laboratory 173.136 Corrosion Testing of Metals for the Process Industries, 1969. National Institutes of Health Bethesda, MD 20892 NIH Guidelines for Research Involving 173.134 Recombinant DNA Molecules (NIH Guidelines), January 2001, Appendix B. Society of Plastics Industries, Inc., Organic Peroxide Producers Safety Division, 1275 K Street, NW., Suite 400, Washington, DC 20005 Self Accelerating Decomposition Temperature 173.21 Test, 1972. ------------------------------------------------------------------------ [Amdt. 171-111, 55 FR 52466, Dec. 21, 1990] Editorial Note: For Federal Register citations affecting Sec. 171.7, see the List of CFR Sections Affected which appears in the Finding Aids section of the printed volume and on GPO Access. Editorial Note: At 68 FR 19273, Apr. 18, 2003, Sec. 171.7(a)(3) was amended by removing the entry for ``TTMA TB No. 81'' under ``Truck Trailer Manufacturers Association''. The amendment could not be incorporated because that entry does not exist.