[Code of Federal Regulations] [Title 40, Volume 30] [Revised as of July 1, 2004] From the U.S. Government Printing Office via GPO Access [CITE: 40CFR1068.260] [Page 708-710] TITLE 40--PROTECTION OF ENVIRONMENT CHAPTER I--ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PART 1068_GENERAL COMPLIANCE PROVISIONS FOR NONROAD PROGRAMS--Table of Contents Subpart C_Exemptions and Exclusions Sec. 1068.260 What are the provisions for temporarily exempting engines for delegated final assembly? (a) Shipping an engine separately from an aftertreatment component that you have specified as part of its certified configuration will not be a violation of the prohibitions in [[Page 709]] Sec. 1068.101(a)(1), if you do all the following: (1) Apply for and receive a certificate of conformity for the engine and its emission-control system before shipment. (2) Provide installation instructions in enough detail to ensure that the engine will be in its certified configuration if someone follows these instructions. (3) Have a contractual agreement with an equipment manufacturer obligating the equipment manufacturer to complete the final assembly of the engine so it is in its certified configuration when installed in the equipment. This agreement must also obligate the equipment manufacturer to provide the affidavits and cooperate with the audits required under paragraph (a)(6) of this section. (4) Include the cost of all aftertreatment components in the cost of the engine. (5) Ship the aftertreatment components directly to the equipment manufacturer, or arrange for separate shipment by the component manufacturer directly to the equipment manufacturer. (6) Take appropriate additional steps to ensure that all engines will be in their certified configuration when installed by the equipment manufacturer. At a minimum do the following: (i) Obtain annual affidavits from every equipment manufacturer to whom you, your distributors, or your dealers sell engines under this section. The affidavits must list the part numbers of the aftertreatment devices that equipment manufacturers install on each engine they purchase from you, your distributors, or your dealers under this section. (ii) If you sell more than 50 engines per model year under this section, you must annually audit four equipment manufacturers to whom you sell engines under this section. To select individual equipment manufacturers, divide all the affected equipment manufacturers into quartiles based on the number of engines they buy from you; select a single equipment manufacturer from each quartile each model year. Vary the equipment manufacturers you audit from year to year, though you may repeat an audit in a later model year if you find or suspect that a particular equipment manufacturer is not properly installing aftertreatment devices. If you sell engines to fewer than 16 equipment manufacturers under the provisions of this section, you may instead set up a plan to audit each equipment manufacturer on average once every four model years. Audits must involve the assembling companies' facilities, procedures, and production records to monitor their compliance with your instructions, must include investigation of some assembled engines, and must confirm that the number of aftertreatment devices shipped were sufficient for the number of engines produced. Where an equipment manufacturer is not located in the United States, you may conduct the audit at a distribution or port facility in the United States. You must keep records of these audits and provide a report describing any uninstalled or improperly installed aftertreatment components to us within 90 days of the audit. (iii) If you sell up to 50 engines per model year under this section, you must conduct audits as described in paragraph (a)(6)(ii) of this section or propose an alternative plan for ensuring that equipment manufacturers properly install aftertreatment devices. (7) Describe the following things in your application for certification: (i) How you plan to use the provisions of this section. (ii) A detailed plan for auditing equipment manufacturers, as described in paragraph (a)(6) of this section. (iii) All other steps you plan to take under paragraph (a)(6) of this section. (8) Keep records to document how many engines you produce under this exemption. Also, keep records to document your contractual agreements under paragraph (a)(3) of this section. Keep all these records for five years after the end of the model year and make them available to us upon request. (9) Make sure the engine has the emission control information label we require under the standard-setting part. Apply an additional temporary [[Page 710]] label or tag in a way that makes it unlikely that the engine will be installed in equipment other than in its certified configuration. The label or tag must identify the engine as incomplete and include a clear statement that failing to install the aftertreatment device, or otherwise bring the engine into its certified configuration, is a violation of federal law subject to civil penalty. (b) An engine you produce under this section becomes new when it is fully assembled, except for aftertreatment devices, for the first time. Use this date to determine the engine's model year. (c) Once the equipment manufacturer takes possession of an engine exempted under this section, the exemption expires and the engine is subject to all the prohibitions in 40 CFR 1068.101. (d) You must notify us within 15 days if you find from an audit or another source that an equipment manufacturer has failed to meet its obligations under this section. (e) We may suspend, revoke, or void an exemption under this section, as follows: (1) We may suspend or revoke your exemption for the entire engine family if we determine that any of the engines are not in their certified configuration after installation in the equipment, or if you fail to comply with the requirements of this section. If we suspend or revoke the exemption for any of your engine families under this paragraph (d), this exemption will not apply for future certificates unless you demonstrate that the factors causing the nonconformity do not apply to the other engine families. We may suspend or revoke the exemption for shipments to a single facility where final assembly occurs. (2) We may void your exemption for the entire engine family if you intentionally submit false or incomplete information or fail to keep and provide to EPA the records required by this section. (f) You are liable for the in-use compliance of any engine that is exempt under this section. It is also a violation of Sec. 1068.101(b)(1) for any person to complete assembly of the exempted engine without complying fully with the installation instructions. [69 FR 39268, June 29, 2004] Effective Date Note: At 69 FR 39268, June 29, 2004, Sec. 1068.260 was added, effective Aug. 30, 2004.