[Code of Federal Regulations] [Title 49, Volume 3] [Revised as of October 1, 2004] From the U.S. Government Printing Office via GPO Access [CITE: 49CFR192.7] [Page 33-35] TITLE 49--TRANSPORTATION CHAPTER I--RESEARCH AND SPECIAL PROGRAMS ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PART 192_TRANSPORTATION OF NATURAL AND OTHER GAS BY PIPELINE: MINIMUM FEDERAL SAFETY STANDARDS--Table of Contents Subpart A_General Sec. 192.7 Incorporation by reference. (a) Any documents or portions thereof incorporated by reference in this part are included in this part as though set out in full. When only a portion of a document is referenced, the remainder is not incorporated in this part. (b) All incorporated materials are available for inspection in the Research and Special programs Administration, 400 Seventh Street, SW., Washington, DC, or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030 or go to: http://www.archives.gov/federal--register/ code--of--federal--regulations/ibr--locations.html. These materials have been approved for incorporation by reference by the Director of the Federal Register in accordance with 5 U.S.C. 552(a) and 1 CFR part 51. In addition, the incorporated materials are available from the respective organizations listed in paragraph (c) (1) of this section. (c) The full titles of documents incorporated by reference, in whole or in part, are provided herein. The numbers in parentheses indicate applicable editions. For each incorporated document, citations of all affected sections are provided. Earlier editions of currently listed documents or editions of documents listed in previous editions of 49 CFR Part 192 may be used for materials and components designed, manufactured, or installed in accordance with these earlier documents at the time they were listed. The user must refer to the appropriate previous edition of 49 CFR Part 192 for a listing of the earlier listed editions or documents. (1) Incorporated by reference (ibr). List of Organizations and Addresses. (i) American Gas Association (AGA), 400 North Capitol Street, NW, Washington, DC 20001. (ii) American Petroleum Institute (API), 1220 L Street, NW, Washington, DC 20005. (iii) American Society for Testing and Materials (ASTM), 100 Barr Harbor Drive, West Conshohocken, PA 19428. (iv) ASME International (ASME), Three Park Avenue, New York, NY 10016-5990. (v) Manufacturers Standardization Society of the Valve and Fittings Industry, Inc. (MSS), 127 Park Street, NE, Vienna, VA 22180. [[Page 34]] (vi) National Fire Protection Association (NFPA), 1 Batterymarch Park, P.O. Box 9101, Quincy, MA 02269-9101. (vii) Plastics Pipe Institute, Inc. (PPI), 1825 Connecticut Avenue, NW, Suite 680, Washington, DC 20009. (viii) NACE International (NACE), 1440 South Creek Drive, Houston, TX 77084. (ix) Gas Technology Institute (GTI), 1700 South Mount Prospect Road, Des Plaines, IL 60018. (2) Documents incorporated by reference (Numbers in Parentheses Indicate Applicable Editions). ------------------------------------------------------------------------ Source and name of referenced material 49 CFR reference ------------------------------------------------------------------------ A. American Gas Association (AGA): (1) AGA Pipeline Research Committee, Sec. Sec. 192.933(a); Project PR-3-805, ``A Modified Criterion 192.485(c). for Evaluating the Remaining Strength of Corroded Pipe'' (AGA PR-3-805-1989). B. American Petroleum Institute (API): (1) API Specification 5L ``Specification Sec. Sec. 192.55(e); for Line Pipe'' (API 5L,42nd edition, 192.113; Item I of 2000). Appendix B to part 192. (2) API Recommended Practice 5L1 Sec. 192.65(a). ``Recommended Practice for Railroad Transportation of Line Pipe'' (4th edition, 1990). (3) API Specification 6D ``Specification Sec. 192.145(a). for Pipeline Valves (Gate, Plug, Ball, and Check Valves)'' (21st edition, 1994). (4) API 1104 ``Welding of Pipelines and Sec. Sec. 192.227(a); Related Facilities'' (19th edition, 192.229(c)(1); 1999, including its October 31, 2001 192.241(c); Item II, errata). Appendix B to part 192. C. American Society for Testing and Materials (ASTM): (1) ASTM Designation: A 53/A53M-99b Sec. Sec. 192.113; ``Standard Specification for Pipe, Item I, Appendix B to Steel, Black and Hot-Dipped, Zinc- part 192. Coated, Welded and Seamless'' (ASTM A53/ A53M-99b). (2) ASTM Designation: A106 ``Standard Sec. Sec. 192.113; Specification for Seamless Carbon Steel Item I, Appendix B to Pipe for High-Temperature Service'' part 192. (A106-99). (3) ASTM Designation: A333/A333M Sec. Sec. 192.113; ``Standard Specification for Seamless Item I, Appendix B to and Welded Steel Pipe for Low- part 192. Temperature Service'' (ASTM A333/A333M- 99). (4) ASTM Designation: A372/A372M Sec. 192.177(b)(1). ``Standard Specification for Carbon and Alloy Steel Forgings for Thin-Walled Pressure Vessels'' (ASTM A372/A372M- 1999). (5) ASTM Designation: A381 ``Standard Sec. Sec. 192.113; Specification for Metal-Arc-Welded Steel Item I, Appendix B to Pipe for Use With High-Pressure part 192. Transmission Systems'' (ASTM A381-1996). (6) ASTM Designation: A671 ``Standard Sec. Sec. 192.113; Specification for Electric-Fusion-Welded Item I, Appendix B to Steel Pipe for Atmospheric and Lower part 192. Temperatures'' (ASTM A671-1996). (7) ASTM Designation: A672 ``Standard Sec. Sec. 192.113; Specification for Electric-Fusion-Welded Item I, Appendix B to Steel Pipe for High-Pressure Service at part 192. Moderate Temperatures'' (A672-1996). (8) ASTM Designation: A691 ``Standard Sec. Sec. 192.113; Specification for Carbon and Alloy Steel Item I, Appendix B to Pipe, Electric-Fusion-Welded for High- part 192. Pressure Service at High Temperatures'' (ASTM A691-1998). (9) ASTM Designation: D638 ``Standard Sec. Sec. Test Method for Tensile Properties of 192.283(a)(3); Plastics'' (ASTM D638-1999). 192.283(b)(1). (10) ASTM Designation: D2513-87 Sec. 192.63(a)(1). ``Standard Specification for Thermoplastic Gas Pressure Pipe, Tubing, and Fittings'' (ASTM D2513-1987). (11) ASTM Designation: D2513 ``Standard Sec. Sec. 192.191(b); Specification for Thermoplastic Gas 192.281(b)(2); Pressure Pipe, Tubing, and Fittings. 192.283(a)(1)(i); Item (D2513-1999). I, Appendix B to part 192. (12) ASTM Designation: D 2517 ``Standard Sec. Sec. 192.191(a); Specification for Reinforced Epoxy Resin 192.281(d)(1); Gas Pressure Pipe and Fittings'' (D2517- 192.283(a)(1)(ii); Item 2000). I, Appendix B to part 192. (13) ASTM Designation: F1055 ``Standard Sec. Specification for Electrofusion Type 192.283(a)(1)(iii). Polyethylene Fittings for Outside Diameter Controlled Polyethylene Pipe and Tubing'' (F1055-1998).. D. ASME International (ASME): (1) ASME/ANSI B16.1 ``Cast Iron Pipe Sec. 192.147(c). Flanges and Flanged Fittings'' (ASME B16.1-1998). (2) ASME/ANSI B16.5 ``Pipe Flanges and Sec. Sec. 192.147(a); Flanged Fittings'' (ASME B16.5-1996, 192.279. including ASME B16.5a-1998 Addenda). (3) ASME/ANSI B31G ``Manual for Sec. Sec. 192.485(c); Determining the Remaining Strength of 192.933(a). Corroded Pipelines'' (ASME/ANSI B31G- 1991). (4) ASME/ANSI B31.8 ``Gas Transmission Sec. 192.619(a)(1)(i). and Distribution Piping Systems'' (ASME/ ANSI B31.8-1995). [[Page 35]] (5) ASME/ANSI B31.8S ``Supplement to B31.8 on Sec. Sec. 192.903(c); Managing System Integrity of Gas Pipelines'' 192.907(b); 192.911, (ASME/ANSI B31.8S-2002). Introductory text; 192.911(i); 192.911(k); 192.911(l); 192.911(m); 192.913(a) Introductory text; 192.913(b)(1); 192.917(a) Introductory text; 192.917(b); 192.917(c); 192.917(e)(1); 192.917(e)(4); 192.921(a)(1); 192.923(b)(2); 192.923(b)(3); 192.925(b) Introductory text; 192.925(b)(1); 192.925(b)(2); 192.925(b)(3); 192.925(b)(4); 192.927(b); 192.927(c)(1)(i); 192.929(b)(1); 192.929(b)(2); 192.933(a); 192.933(d)(1); 192.933(d)(1)(i); 192.935(a); 192.935(b)(1)(iv); 192.937(c)(1); 192.939(a)(1)(i); 192.939(a)(1)(ii); 192.939(a)(3); 192.945(a). (6) ASME Boiler and Pressure Vessel Code, Sec. Sec. 192.153(a). Section I, Rules for Construction of Power Boilers (ASME Section I-1998). (7) ASME Boiler and Pressure Vessel Code, Sec. Sec. 192.153(a); Section VIII, Division 1, ``Rules for 192.153(b); 192.153(d); Construction of Pressure Vessels'' (ASME 192.165(b)(3). Section VIII Division 1-2001). (8) ASME Boiler and Pressure Vessel Code, Sec. Sec. 192.153(b); Section VIII, Division 2, ``Rules for 192.165(b)(3). Construction of Pressure Vessels: Alternative Rules'' (ASME Section VIII Division 2-2001). (9) ASME Boiler and Pressure Vessel Code, Sec. Sec. 192.227(a); Section IX, ``Welding and Brazing Item II, Appendix B to Qualifications'' (ASME Section IX-2001). part 192. E. Manufacturers Standardization Society of the Valve and Fittings Industry, Inc. (MSS): (1) MSS SP44-96 ``Steel Pipe Line Sec. 192.147(a). Flanges'' (MSS SP-44-1996 including 1996 errata). (2) [Reserved]........................... F. National Fire Protection Association (NFPA): (1) NFPA 30 ``Flammable and Combustible Sec. 192.735(b). Liquids Code'' (NFPA 30-1996). (2) ANSI/NFPA 58 ``Liquefied Petroleum Sec. 192.11(a); Gas Code (LP-Gas Code)'' (NFPA 58-1998). 192.11(b); 192.11(c). (3) ANSI/NFPA 59 ``Standard for the Sec. 192.11(a); storage and Handling of Liquefied 192.11(b); 192.11(c). Petroleum Gases at Utility Gas Plants'' (NFPA 59-1998). (4) ANSI/NFPA 70 ``National Electrical Sec. Sec. 192.163(e); Code'' (NFPA 70-1996). 192.189(c). G. Plastics Pipe Institute, Inc. (PPI): (1) PPI TR-3/2000 ``Policies and Sec. Sec. 192.121. Procedures for Developing Hydrostatic Design Bases (HDB), Pressure Design Bases (PDB), and Minimum Required Strength (MRS) Ratings for Thermoplastic Piping Materials ``(PPI TR-3-2000-Part E only, ``Policy for Determining Long Term Strength (LTHS) by Temperature Interpolation)''. H. NACE International (NACE): (1) NACE Standard RP-0502-2002 ``Pipeline Sec. Sec. External Corrosion Direct Assessment 192.923(b)(1); Methodology'' (NACE RP-0502-2002). 192.925(b) Introductory text; 192.925(b)(1); 192.925(b)(1)(ii); 192.925(b)(2) Introductory text; 192.925(b)(3) Introductory text; 192.925(b)(3)(ii); 192.925(b)(iv); 192.925(b)(4) Introductory text; 192.925(b)(4)(ii); 192.931(d); 192.935(b)(1)(iv); 192.939(a)(2). I. Gas Technology Institute (GTI). (Formerly Gas Research Institute): (1) GRI 02/0057 ``Internal Corrosion Sec. 192.927(c)(2); Direct Assessment of Gas Transmission 192.7. Pipelines--Methodology'' (GRI 02/0057- 2002). ------------------------------------------------------------------------ [35 FR 13257, Aug. 19, 1970, as amended by Amdt. 192-37, 46 FR 10159, Feb. 2, 1981; Amdt 192-51, 51 FR 15334, Apr. 23, 1986; 58 FR 14521, Mar. 18, 1993; Amdt. 192-78, 61 FR 28783, June 6, 1996; 69 FR 18803, Apr. 9, 2004; Amdt. 192-94, 69 FR 32892, June 14, 2004; Amdt. 192-94, 69 FR 54592, Sept. 9, 2004]