[Code of Federal Regulations]
[Title 49, Volume 5]
[Revised as of October 1, 2004]
From the U.S. Government Printing Office via GPO Access
[CITE: 49CFR571.106]
[Page 225-239]
TITLE 49--TRANSPORTATION
CHAPTER V--NATIONAL HIGHWAY TRAFFIC
SAFETY ADMINISTRATION, DEPARTMENT
OF TRANSPORTATION
PART 571_FEDERAL MOTOR VEHICLE SAFETY STANDARDS--Table of Contents
Subpart B_Federal Motor Vehicle Safety Standards
Sec. 571.106 Standard No. 106; Brake hoses.
S1. Scope. This standard specifies labeling and performance
requirements for motor vehicle brake hose, brake hose assemblies, and
brake hose end fittings.
S2. Purpose. The purpose of this standard is to reduce deaths and
injuries occurring as a result of brake system failure from pressure or
vacuum loss due to hose or hose assembly rupture.
S3. Application. This standard applies to passenger cars,
multipurpose passenger vehicles, trucks, buses, trailers, and
motorcycles, and to hydraulic, air, and vacuum brake hose, brake hose
assemblies, and brake hose end fittings for use in those vehicles.
S4. Definitions.
Armor means protective material installed on a brake hose to
increase the resistance of the hose or hose assembly to abrasion or
impact damage.
Brake hose means a flexible conduit, other than a vacuum tubing
connector, manufactured for use in a brake system to transmit or contain
the fluid pressure or vacuum used to apply force to a vehicle's brakes.
For hose, a dimensional description such as ``\1/4\-inch hose'' refers
to the nominal inside diameter. For tubing, a dimensional description
such as ``\1/4\-in tubing'' refers to the nominal outside diameter.
Brake hose assembly means a brake hose, with or without armor,
equipped with end fittings for use in a brake system, but does not
include an air or vacuum assembly prepared by the owner or operator of a
used vehicle, by his employee, or by a repair facility, for installation
in that used vehicle.
Brake hose end fitting means a coupler, other than a clamp, designed
for attachment to the end of a brake hose.
Free length means the linear measurement of hose exposed between the
end fittings of a hose assembly in a straight position.
Permanently attached end fitting means an end fitting that is
attached by deformation of the fitting about the hose by crimping or
swaging, or an end fitting that is attached by use of a sacrificial
sleeve or ferrule that requires replacement each time a hose assembly is
rebuilt.
Rupture means any failure that results in separation of a brake hose
from its end fitting or in leakage.
Vacuum tubing connector means a flexible conduit of vacuum that (i)
connects metal tubing to metal tubing in a brake system, (ii) is
attached without end fittings, and (iii) when installed, has an
unsupported length less than the total length of those portions that
cover the metal tubing.
S5. Requirements--hydraulic brake hose, brake hose assemblies, and
brake hose end fittings.
S5.1 Construction. (a) Each hydraulic brake hose assembly shall have
permanently attached brake hose end fittings which are attached by
deformation of the fitting about the hose by crimping or swaging.
(b) Each hydraulic brake hose assembly that is equipped with a
permanent supplemental support integrally attached to the assembly and
is manufactured as a replacement for use on a vehicle not equipped, as
an integral part of the vehicle's original design, with a means of
attaching the support to the vehicle shall be equipped with a bracket
that is integrally attached to the supplemental support and that adapts
the vehicle to properly accept this type of brake hose assembly.
S5.2 Labeling.
S5.2.1 Each hydraulic brake hose, except hose sold as part of a
motor vehicle, shall have at least two clearly
[[Page 226]]
identifiable stripes of at least one-sixteenth of an inch in width,
placed on opposite sides of the brake hose parallel to its longitudinal
axis. One stripe may be interrupted by the information required by
S5.2.2, and the other stripe may be interrupted by additional
information at the manufacturer's option. However, hydraulic brake hose
manufactured for use only in an assembly whose end fittings prevent its
installation in a twisted orientation in either side of the vehicle,
need not meet the requirements of S5.2.1.
S5.2.2 Each hydraulic brake hose shall be labeled, or cut from bulk
hose that is labeled, at intervals of not more than 6 inches, measured
from the end of one legend to the beginning of the next, in block
capital letters and numerals at least one-eighth of an inch high, with
the information listed in paragraphs (a) through (e) of this section.
The information need not be present on hose that is sold as part of a
brake hose assembly or a motor vehicle.
(a) The symbol DOT, constituting a certification by the hose
manufacturer that the hose conforms to all applicable motor vehicle
safety standards.
(b) A designation that identifies the manufacturer of the hose,
which shall be filed in writing with: Office of Crash Avoidance
Standards, Vehicle Dynamics Division, National Highway Traffic Safety
Administration, 400 Seventh Street, SW., Washington, DC 20590. The
marking may consist of a designation other than block capital letters
required by S5.2.2.
(c) The month, day, and year, or the month and year, of manufacture,
expressed in numerals. For example, 10/1/96 means October 1, 1996.
(d) The nominal inside diameter of the hose expressed in inches or
fractions of inches, or in millimeters followed by the abbreviation
``mm.''
(e) Either ``HR'' to indicate that the hose is regular expansion
hydraulic hose or ``HL'' to indicate that the hose is low expansion
hydraulic hose.
S5.2.3 Package labeling for brake hose assemblies designed to be
used with a supplemental support. (a) Each hydraulic brake hose assembly
that is equipped with a permanent supplemental support integrally
attached to the assembly and is manufactured as a replacement assembly
for a vehicle equipped, as an integral part of the vehicle's original
design, with a means of attaching the support to the vehicle shall be
sold in a package that is marked or labeled as follows: ``FOR USE ON
[insert Manufacturer, Model Name] ONLY'';
(b) Each hydraulic brake hose assembly that is equipped with a
permanent supplemental support integrally attached to the assembly and
is manufactured as a replacement for use on a vehicle not equipped, as
an integral part of the vehicle's original design, with a means of
attaching the support to the vehicle shall comply with paragraphs (a)
(1) and (2) of this section:
(1) Be sold in a package that is marked or labeled as follows: ``FOR
USE ONLY WITH A SUPPLEMENTAL SUPPORT.''
(2) Be accompanied by clear, detailed instructions explaining the
proper installation of the brake hose and the supplemental support
bracket to the vehicle and the consequences of not attaching the
supplemental support bracket to the vehicle. The instructions shall be
printed on or included in the package specified in paragraph (a)(1) of
this section.
S5.2.4 Each hydraulic brake hose assembly, except those sold as part
of a motor vehicle, shall be labeled by means of a band around the brake
hose assembly as specified in this paragraph or, at the option of the
manufacturer, by means of labeling as specified in S5.2.4.1. The band
may at the manufacturer's option be attached so as to move freely along
the length of the assembly, as long as it is retained by the end
fittings. The band shall be etched, embossed, or stamped in block
capital letters, numerals or symbols at least one-eighth of an inch
high, with the following information:
(a) The symbol DOT constituting certification by the hose assembler
that the hose assembly conforms to all applicable motor vehicle safety
standards.
(b) A designation that identifies the manufacturer of the hose
assembly, which shall be filed in writing with: Office of Crash
Avoidance Standards, Vehicle Dynamics Division, National
[[Page 227]]
Highway Traffic Safety Administration, 400 Seventh Street SW.,
Washington, DC 20590. The designation may consist of block capital
letters, numerals or a symbol.
S5.2.4.1 At least one end fitting of a hydraulic brake hose assembly
shall be etched, stamped or embossed with a designation at least one-
sixteenth of an inch high that identifies the manufacturer of the hose
assembly and is filed in accordance with S5.2.4(b).
S5.3 Test requirements. A hydraulic brake hose assembly or
appropriate part thereof shall be capable of meeting any of the
requirements set forth under this heading, when tested under the
conditions of S11 and the applicable procedures of S6. However, a
particular hose assembly or appropriate part thereof need not meet
further requirements after having been subjected to and having met the
constriction requirement (S5.3.1) and any one of the requirements
specified in S5.3.2 through S5.3.11.
S5.3.1 Constriction. Except for that part of an end fitting which
does not contain hose, every inside diameter of any section of a
hydraulic brake hose assembly shall be not less than 64 percent of the
nominal inside diameter of the brake hose.
S5.3.2 Expansion and burst strength. The maximum expansion of a
hydraulic brake hose assembly at 1,000 psi and 1,500 psi shall not
exceed the values specified in Table I (S6.1). The hydraulic brake hose
assembly shall then withstand water pressure of 4,000 psi for 2 minutes
without rupture, and shall not rupture at less than 5,000 psi (S6.2).
Table 1--Maximum Expansion of Free Length Brake Hose, cc/ft.
------------------------------------------------------------------------
Test Pressure
-------------------------------------------
1,000 psi 1,500 psi
Hydraulic brake hose, inside -------------------------------------------
diameter Regular Low Regular Low
expansion expansion expansion expansion
hose hose hose hose
------------------------------------------------------------------------
\1/8\ inch or 3 mm or less.. 0.66 0.33 0.79 0.42
\3/16\ inch or 4 to 5 mm.... .86 .55 1.02 .72
\1/4\ inch or 6 mm or more.. 1.04 .82 1.30 1.17
------------------------------------------------------------------------
S5.3.3 Whip resistance. A hydraulic brake hose assembly shall not
rupture when run continuously on a flexing machine for 35 hours (S6.3).
S5.3.4 Tensile strength. A hydraulic brake hose assembly shall
withstand a pull of 325 pounds without separation of the hose from its
end fittings (S6.4).
S5.3.5 Water absorption and burst strength. A hydraulic brake hose
assembly, after immersion in water for 70 hours (S6.5), shall withstand
water pressure of 4,000 psi for 2 minutes, and then shall not rupture at
less than 5,000 psi (S6.2).
S5.3.6 Water absorption and tensile strength. A hydraulic brake hose
assembly, after immersion in water for 70 hours (S6.5), shall withstand
a pull of 325 pounds without separation of the hose from its end
fittings (S6.4).
S5.3.7 Water absorption and whip resistance. A hydraulic brake hose
assembly, after immersion in water for 70 hours (S6.5), shall not
rupture when run continuously on a flexing machine for 35 hours (S6.3).
S.5.3.8 Low-temperature resistance. A hydraulic brake hose
conditioned at minus 40 [deg]F. for 70 hours shall not show cracks
visible without magnification when bent around a cylinder as specified
in S6.6. (S6.6)
S5.3.9 Brake fluid compatibility, constriction, and burst strength.
Except for brake hose assemblies designed for use with mineral or
petroleum-based brake fluids, a hydraulic brake hose assembly shall meet
the constriction requirement of S5.3.1 after having been subjected to a
temperature of 200 [deg]F for 70 hours while filled with SAE RM-66-04
Compatibility Fluid, as described in appendix B of SAE Standard J1703
JAN 1995, ``Motor Vehicle Brake Fluid.'' It shall then withstand water
pressure of 4,000 psi for 2 minutes and thereafter shall not rupture at
less than 5,000 psi (S6.2). (SAE RM-66-03 Compatibility Fluid, as
described in appendix A of SAE Standard J1703 NOV83, ``Motor Vehicle
Brake Fluid,'' November 1983, may be used in place of SAE RM-66-04 until
January 1, 1995.)
S5.3.10 Ozone resistance. A hydraulic brake hose shall not show
cracks visible under 7-power magnification after exposure to ozone for
70 hours at 104 [deg]F. (S6.8).
[[Page 228]]
S5.3.11 End fitting corrosion resistance. After 24 hours of exposure
to salt spray, a hydraulic brake hose end fitting shall show no base
metal corrosion on the end fitting surface except where crimping or the
application of labeling information has caused displacement of the
protective coating. (S6.9)
S6. Test procedures--Hydraulic brake hose, brake hose assemblies,
and brake hose end fittings.
S6.1. Expansion test.
S6.1.1 Apparatus. Utilize a test apparatus (as shown in Figure 1)
which consists of:
(a) Source for required fluid pressure;
(b) Test fluid of water without any additives and free of gases;
(c) Reservoir for test fluid;
(d) Pressure gauges;
(e) Brake hose end fittings in which to mount the hose vertically;
and
(f) Graduate burette with 0.05 cc increments.
[GRAPHIC] [TIFF OMITTED] TC01AU91.006
Fig. 1--Expansion Test Apparatus
S6.1.2 Preparation. (a) Measure the free length of the hose
assembly.
(b) Mount the hose so that it is in a vertical straight position
without tension when pressure is applied.
(c) Fill the hose with test fluid and bleed all gases from the
system.
(d) Close the valve to the burette and apply 1,500 psi for 10
seconds; then release pressure.
S6.1.3 Calculation of expansion at 1,000 and 1,500 psi. (a) Adjust
the fluid level in the burette to zero.
(b) Close the valve to the burette, apply pressure at the rate of
15,000 psi per minute, and seal 1,000 psi in the hose (1,500 psi in
second series).
(c) After 3 seconds open the valve to the burette for 10 seconds and
allow the fluid in the expanded hose to rise into the burette.
(d) Repeat the procedure in steps (b) and (c) twice. Measure the
amount of test fluid which has accumulated in the burette as a result of
the three applications of pressure.
(e) Calculate the volumetric expansion per foot by dividing the
total accumulated test fluid by 3 and further dividing by the free
length of the hose in feet.
S6.2 Burst strength test. (a) Connect the brake hose to a pressure
system and fill it completely with water, allowing all gases to escape.
(b) Apply water pressure of 4,000 psi at a rate of 15,000 psi per
minute.
(c) After 2 minutes at 4,000 psi, increase the pressure at the rate
of 15,000 psi per minute until the pressure exceeds 5,000 psi.
S6.3 Whip resistance test.
S6.3.1 Apparatus. Utilize test apparatus that is dynamically
balanced and includes:
(a) A movable header consisting of a horizontal bar equipped with
capped end fittings and mounted through bearings at each end to points 4
inches from the center of two vertically rotating disks whose edges are
in the same vertical plane;
(b) An adjustable stationary header parallel to the movable header
in the same horizontal plane as the centers of the disks, and fitted
with open end fittings;
(c) An elapsed time indicator; and
(d) A source of water pressure connected to the open end fittings.
S6.3.2 Preparation. (a) Except for the supplemental support
specified in S6.3.2(d), remove all external appendages including, but
not limited to, hose armor, chafing collars, mounting brackets, date
band and spring guards.
(b) Measure the hose free length.
(c) Mount the hose in the whip test machine, introducing slack as
specified
[[Page 229]]
in Table II for the size hose tested, measuring the projected length
parallel to the axis of the rotating disks. The manufacturer may, at his
option, adapt the fitting attachment points to permit mounting hose
assemblies equipped with angled or other special fittings in the same
orientation as hose assemblies equipped with straight fittings.
(d) In the case of a brake hose assembly equipped with a permanent
supplemental support integrally attached to the assembly, the assembly
may be mounted using the supplemental support and associated means of
simulating its attachment to the vehicle. Mount the supplemental support
in the same vertical and horizontal planes as the stationary header end
of the whip test fixture described in S6.3.1(b). Mount or attach the
supplemental support so that it is positioned in accordance with the
recommendation of the assembly manufacturer for attaching the
supplemental support on a vehicle.
Table II--Hose Lengths
------------------------------------------------------------------------
Slack, inches
-----------------------
\1/8\ inch More than
Free length between end fittings, inches or 3 mm \1/8\ inch
hose or or 3 mm
less hose
------------------------------------------------------------------------
8 to 15\1/2\, inclusive......................... 1.750 ..........
10 to 15\1/2\, inclusive........................ .......... 1,000
Over 15\1/2\ to 19 inclusive.................... 1.250 ..........
Over 19 to 24, inclusive........................ 0.750 ..........
------------------------------------------------------------------------
S6.3.3 Operation. (a) Apply 235 psi water pressure and bleed all
gases from the system.
(b) Drive the movable head at 800 rpm.
S6.4 Tensile strength test. Utilize a tension testing machine
conforming to the requirements of the methods of Verification of Testing
Machines (1964 American Society for Testing and Materials, Designation
E4), and provided with a recording device to give the total pull in
pounds.
S6.4.1 Preparation. Mount the hose assembly to ensure straight,
evenly distributed machine pull.
S6.4.2 Operation. Apply tension at a rate of 1 inch per minute
travel of the moving head until separation occurs.
S6.5 Water absorption sequence tests.
S6.5.1 Preparation. Prepare three hose assemblies as follows:
(a) Remove 1\1/8\ inches of hose cover, if any, from the center of
the hose assemblies without injury to any reinforcing material or
elongation of the hose assemblies.
(b) Measure the free length of the hose assemblies.
S.6.5.2 Immersion and sequence testing. (a) Immerse the hose
assemblies in distilled water for 70 hours.
(b) Thirty minutes after removal from water, conduct tests S6.2,
S6.3, and S6.4, using a different hose for each sequence.
S6.6 Low temperature resistance test.
S6.6.1 Preparation. (a) Remove hose armor, if any, and condition a
hose in a straight position in air at minus 40 [deg]F. for 70 hours.
(b) Condition a cylinder in air at minus 40 [deg]F for 70 hours,
using a cylinder of 2\1/2\ inches diameter for test of hose less than
\1/8\ inch or 3 mm 3 inches for tests of \1/8\ inch or 3mm hose, 3\1/2\
inches for tests of \3/16\ and \1/4\ inch hose or of 4 to 6 mm hose, and
4 inches for tests of hose greater than \1/4\ inch or 6 mm in diameter.
S6.6.2 Flexibility testing. Bend the conditioned hose 180 degrees
around the conditioned cylinder at a steady rate in a period of 3 to 5
seconds. Examine without magnification for cracks.
S6.7 Brake fluid compatibility test.
S6.7.1 Preparation. (a) Attach a hose assembly below a 1-pint
reservoir filled with 100 ml. of SAE RM-66-04 Compatibility Fluid as
shown in Figure 2. (SAE RM-66-03 Compatibility Fluid, as described in
appendix A of SAE Standard J1703 NOV83, ``Motor Vehicle Brake Fluid,''
November 1983, may be used in place of SAE RM-66-04 until January 1,
1995.)
(b) Fill the hose assembly with brake fluid, seal the lower end, and
place the test assembly in an oven in a vertical position.
[[Page 230]]
[GRAPHIC] [TIFF OMITTED] TC01AU91.007
S6.7.2 Oven treatment. (a) Condition the hose assembly at 200
[deg]F. for 70 hours.
(b) Cool the hose assembly at room temperature for 30 minutes.
(c) Drain the brake hose assembly, immediately determine that every
inside diameter of any section of the hose assembly, except for that
part of an end fitting which does not contain hose, is not less than 64
percent of the nominal inside diameter of the hose, and conduct the test
specified in S6.2.
S6.8 Ozone resistance test. Utilize a cylinder with a diameter eight
times the nominal outside diameter of the brake hose excluding armor.
S6.8.1 Preparation. After removing any armor, bind a hydraulic brake
hose 360[deg] around the cylinder. In the case of hose shorter than the
circumference of the cylinder, bend the hose so that as much of its
length as possible is in contact.
S6.8.2 Exposure to ozone. (a) Condition the hose on the cylinder in
air at room temperature for 24 hours.
(b) Immediately thereafter, condition the hose on the cylinder for
70 hours in an exposure chamber having an ambient air temperature of 104
[deg]F. during the test and containing air mixed with ozone in the
proportion of 50 parts of ozone per 100 million parts of air by volume.
(c) Examine the hose for cracks under 7-power magnification,
ignoring areas immediately adjacent to or within the area covered by
binding.
S6.9 End fitting corrosion resistance test. Utilize the apparatus
described in ASTM B117-64, ``Salt Spray (Fog) Testing''.
S6.9.1 Construction. Construct the salt spray chamber so that:
(a) The construction material does not affect the corrosiveness of
the fog.
(b) The hose assembly is supported or suspended 30[deg] from the
vertical and parallel to the principal direction of the horizontal flow
of fog through the chamber.
(c) The hose assembly does not contact any metallic material or any
material capable of acting as a wick.
(d) Condensation which falls from the assembly does not return to
the solution reservoir for respraying.
(e) Condensation from any source does not fall on the brake hose
assemblies or the solution collectors.
(f) Spray from the nozzles is not directed onto the hose assembly.
S6.9.2 Preparation. (a) Plug each end of the hose assembly.
(b) Mix a salt solution five parts by weight of sodium chloride to
95 parts of distilled water, using sodium chloride substantially free of
nickel and copper, and containing on a dry basis not more than 0.1
percent of sodium iodide and not more than 0.3 percent total impurities.
Ensure that the solution is free of suspended solids before the solution
is atomized.
(c) After atomization at 95 [deg]F. ensure that the collected
solution is in the PH range of 6.5 to 7.2. Make the PH measurements at
77 [deg]F.
(d) Maintain a compressed air supply to the nozzle or nozzles free
of oil and dirt and between 10 and 25 psi.
S6.9.3 Operation. Subject the brake hose assembly to the salt spray
continuously for 24 hours.
(a) Regulate the mixture so that each collector will collect from 1
to 2 ml. of solution per hour for each 80 square centimeters of
horizontal collecting area.
(b) Maintain exposure zone temperature at 95 [deg]F.
[[Page 231]]
(c) Upon completion, remove the salt deposit from the surface of the
hoses by washing gently or dipping in clean running water not warmer
than 100 [deg]F. and then drying immediately.
S7. Requirements--Air brake hose, brake hose assemblies, and brake
hose end fittings.
S7.1 Construction. Each air brake hose assembly shall be equipped
with permanently attached brake hose end fittings or reusable brake hose
end fittings. Each air brake hose constructed of synthetic or natural
elastomeric rubber intended for use with reusable end fittings shall
conform to the dimensional requirements specified in Table III.
Table III--Air Brake Hose Dimensions for Reusable Assemblies
----------------------------------------------------------------------------------------------------------------
Type I outside diameter, Type II outside
Inside diameter inches diameter, inches
Size, inches tolerance, inches ---------------------------------------------------
Minimum Maximum Minimum Maximum
----------------------------------------------------------------------------------------------------------------
\3/16\................................... +0.026 0.472 0.510 0.500 0.539
-0.000
\1/4\.................................... +0.031 0.535 0.573 0.562 0.602
-0.000
\5/16\................................... +0.031 0.598 0.636 0.656 0.695
-0.000
\3/8\.................................... 0.023
\13/32\.................................. +0.031 0.714 0.760 0.742 0.789
-0.000
\1/2\.................................... +0.039 0.808 0.854 0.898 0.945
-0.000
\5/8\.................................... +0.042 0.933 0.979 1.054 1.101
-0.000
\1/2\ special............................ .031
----------------------------------------------------------------------------------------------------------------
S7.2 Labeling
S7.2.1 Hose. Each air brake hose shall be labeled, or cut from bulk
hose that is labeled, at intervals of not more than 6 inches, measured
from the end of one legend to the beginning of the next, in block
capital letters and numerals at least one-eighth of an inch high, with
the information listed in paragraphs (a) through (e) of this section.
The information need not be present on hose that is sold as part of a
brake hose assembly or a motor vehicle.
(a) The symbol DOT, constituting a certification by the hose
manufacturer that the hose conforms to all applicable motor vehicle
safety standards.
(b) A designation that identifies the manufacturer of the hose,
which shall be filed in writing with: Office of Crash Avoidance
Standards, Vehicle Dynamics Division, National Highway Traffic Safety
Administration, 400 Seventh Street SW., Washington, DC 20590. The
designation may consist of block capital letters, numerals, or a symbol.
(c) The month, day, and year, or the month and year, of manufacture,
expressed in numerals. For example, 10/1/96 means October 1, 1996.
(d) The nominal inside diameter of the hose expressed in inches or
fractions of inches or in millimeters, or the nominal outside diameter
of plastic tubing expressed in inches or fractions of inches or in
millimeters followed by the letters OD. The abbreviation ``mm'' shall
follow hose sizes that are expressed in millimeters. (Examples of inside
diameter: \1/8\, \1/2\ (\1/2\SP in the case of \1/2\ inch special air
brake hose), 4 mm, 6 mm. Examples of outside diameter: \1/4\ OD, 12 mm
OD.)
(e) The letter ``A'' shall indicate intended use in air brake
systems. In the case of a hose constructed of synthetic or natural
elastomeric rubber intended for use in a reusable assembly, ``AI'' or
``AII'' shall indicate Type I or Type II dimensional characteristics of
the hose as described in Table III.
S7.2.2 End fittings. Except for an end fitting that is attached by
deformation of the fitting about a hose by crimping or swaging, at least
one component of each air brake hose fitting shall be etched, embossed,
or stamped in block capital letters and numerals at least
[[Page 232]]
one-sixteenth of an inch high with the following information:
(a) The symbol DOT, constituting a certification by the manufacturer
of that component that the component conforms to all applicable motor
vehicle safety standards.
(b) A designation that identifies the manufacturer of that component
of the fitting, which shall be filed in writing with: Office of Crash
Avoidance Standards, Vehicle Dynamics Division, National Highway Traffic
Safety Administration, 400 Seventh Street SW., Washington, DC 20590. The
designation may consist of block capital letters, numerals, or a symbol.
(c) The letter ``A'' shall indicate intended use in air brake
systems. In the case of an end fitting intended for use in a reusable
assembly with brake hose subject to Table III, ``AI'' or ``AII'' shall
indicate use with Type I or Type II hose, respectively.
(d) The nominal inside diameter of the hose to which the fitting is
properly attached expressed in inches or fractions of inches or in
millimeters, or the outside diameter of the plastic tubing to which the
fitting is properly attached expressed in inches or fractions of inches
or in millimeters followed by the letters OD (See examples in
S7.2.1(d)). The abbreviations ``mm'' shall follow hose sizes that are
expressed in millimeters.
S7.2.3 Assemblies. Each air brake hose assembly made with end
fittings that are attached by crimping or swaging, except those sold as
part of a motor vehicle, shall be labeled by means of a band around the
brake hose assembly as specified in this paragraph or, at the option of
the manufacturer, by means of labeling as specified in S7.2.3.1. The
band may at the manufacturer's option be attached so as to move freely
along the length of the assembly, as long as it is retained by the end
fittings. The band shall be etched, embossed, or stamped in block
capital letters, numerals or symbols at least one-eighth of an inch
high, with the following information:
(a) The symbol DOT, constituting certification by the hose assembler
that the hose assembly conforms to all applicable motor vehicle safety
standards.
(b) A designation that identifies the manufacturer of the hose
assembly, which shall be filed in writing with: Office of Crash
Avoidance Standards, Vehicle Dynamics Division, National Highway Traffic
Safety Administration, 400 Seventh Street SW., Washington, DC 20590. The
designation may consist of block capital letters, numerals or a symbol.
S7.2.3.1 At least one end fitting of an air brake hose assembly made
with end fittings that are attached by crimping or swaging shall be
etched, stamped or embossed with a designation at least one-sixteenth of
an inch high that identifies the manufacturer of the hose assembly and
is filed in accordance with S7.2.3(b).
S7.3 Test requirements. Each air brake hose assembly or appropriate
part thereof shall be capable of meeting any of the requirements set
forth under this heading, when tested under the conditions of S11 and
the applicable procedures of S8. However, a particular hose assembly or
appropriate part thereof need not meet further requirements after having
met the constriction requirement (S7.3.1) and then having been subjected
to any one of the requirements specified in S7.3.2 through S7.3.13.
S7.3.1 Construction. Except for that part of an end fitting which
does not contain hose, every inside diameter of any section of an air
brake hose assembly shall be not less than 66 percent of the nominal
inside diameter of the brake hose.
S7.3.2 High temperature resistance. An air brake hose shall not show
external or internal cracks, charring, or disintegration visible without
magnification when straightened after being bent for 70 hours at 212
[deg]F. over a cylinder having the radius specified in Table IV for the
size of hose tested (S8.1).
S7.3.3 Low temperature resistance. The outer cover of an air brake
hose shall not show cracks visible without magnification as a result of
conditioning at minus 40 [deg]F. for 70 hours when bent around a
cylinder having the radius specified in Table IV for the size of hose
tested (S8.2).
[[Page 233]]
Table IV--Air Brake Hose Diameters and Test Cylinder Radii
----------------------------------------------------------------------------------------------------------------
Nominal hose diameter, in.*.................... \1/8\ \3/16\ \1/4\ \5/16\ \3/8\, \13/ \7/16\, \1/ \5/8\
32\ 2\
mm.*........................................... 3 4, 5 6 8 10 12 16
Radius of test cylinder in inches.............. 1\1/2\ 2 2\1/2\ 3 3\1/2\ 4 4\1/2\
----------------------------------------------------------------------------------------------------------------
*These sizes are listed to provide test values for brake hoses manufactured in these sizes. They do not
represent conversions.
S7.3.4 Oil resistance. After immersion in ASTM No. 3 oil for 70
hours at 212 [deg]F. the volume of a specimen prepared from the inner
tube and cover of an air brake hose shall not increase more than 100
percent (S8.3).
S7.3.5 Ozone resistance. The outer cover of an air brake hose shall
not show cracks visible under 7-power magnification after exposure to
ozone for 70 hours at 104 [deg]F. (S8.4).
S7.3.6 Length change. An airbrake hose (other than a coiled nylon
tube for use in an assembly that meets the requirements of Sec. 393.45
of this title) shall not contract in length more than 7 percent nor
elongate more than 5 percent when subjected to air pressure of 200 psi
(S8.5).
S7.3.7 Adhesion. Except for hose reinforced by wire, an airbrake
hose shall withstand a tensile force of 8 pounds per inch of length
before separation of adjacent layers (S8.6).
S7.3.8 Air pressure. An air brake hose assembly shall contain air
pressure of 200 psi for 5 minutes without loss of more than 5 psi
(S8.7).
S7.3.9 Burst strength. An air brake hose assembly shall not rupture
when exposed to hydrostatic pressure of 800 psi (S8.8).
S7.3.10 Tensile strength. An air brake hose assembly (other than a
coiled nylon tube assembly which meets the requirements of Sec. 393.45
of this title) designed for use between frame and axle or between a
towed and a towing vehicle shall withstand, without separation of the
hose from its end fittings, a pull of 250 pounds if it is \1/4\ inch or
less or 6 mm or less in nominal internal diameter, or a pull of 325
pounds if it is larger than \1/4\ inch or 6 mm in nominal internal
diameter. An air brake hose assembly designed for use in any other
application shall withstand, without separation of the hose from its end
fitting, a pull of 50 pounds if it is \1/4\ inch or 6 mm or less in
nominal internal diameter, 150 pounds if it is \3/8\ or \1/2\ inch or 10
mm to 12 mm in nominal internal diameter, or 325 pounds if it is larger
than \1/2\ inch or 12 mm in nominal internal diameter (S8.9).
S7.3.11 Water absorption and tensile strength. After immersion in
distilled water for 70 hours (S8.10), an air brake hose assembly (other
than a coiled tube assembly which meets the requirements of Sec. 393.45
of this title) designed for use between frame and axle or between a
towed and a towing vehicle shall withstand without separation of the
hose from its end fittings a pull of 250 pounds if it is \1/4\ inch or 6
mm or less in nominal internal diameter, or a pull of 325 pounds if it
is larger than \1/4\ inch or 6 mm in nominal internal diameter. After
immersion in distilled water for 70 hours (S8.10), an air brake hose
assembly designed for use in any other application shall withstand
without separation of the hose from its end fitting a pull of 50 pounds
if it is \1/4\ inch or 6 mm or less in nominal internal diameter, 150
pounds if it is \3/8\ inch or \1/2\ inch or 10 to 12 mm in nominal
internal diameter, or 325 pounds if it is larger than \1/2\ inch or 12
mm in nominal internal diameter (S8.9).
S7.3.12 Zinc chloride resistance. The outer cover of an air brake
hose shall not show cracks visible under 7-power magnification after
immersion in a 50 percent zinc chloride aqueous solution for 200 hours
(S8.11).
S7.3.13 End fitting corrosion resistance. After 24 hours of exposure
to salt spray, air brake hose end fittings shall show no base metal
corrosion on the end fitting surface except where crimping or the
application of labeling information causes a displacement of the
protective coating.
S8. Test procedures--Air brake hose, brake hose assemblies, and
brake hose end fittings.
S8.1 High temperature resistance test. (a) Utilize a cylinder having
the radius indicated in Table IV for the size of hose tested.
[[Page 234]]
(b) Bind the hose around the cylinder and condition it in an air
oven for 70 hours at 212 [deg]F.
(c) Cool the hose to room temperature, remove it from the cylinder
and straighten it.
(d) Without magnification, examine the hose externally and cut the
hose lengthwise and examine the inner tube.
S8.2 Low temperature resistance test. (a) Utilize a cylinder having
the radius indicated in Table IV for the size of hose tested.
(b) Condition the cylinder and the brake hose, in a straight
position, in a cold box at minus 40 [deg]F. for 70 hours.
(c) With the hose and cylinder at minus 40 [deg]F., bend the hose
180 degrees around the cylinder at a steady rate in a period of 3 to 5
seconds.
S8.3 Oil resistance test. Utilize three test specimens and average
the results.
S8.3.1 Preparation. Fashion a test specimen by cutting a rectangular
block 2 inches long and not less than one-third of an inch in width,
having a thickness of not more than one-sixteenth inch, from the brake
hose and buff the specimen on both faces to ensure smooth surfaces.
S8.3.2 Measurement. (a) Weigh each specimen to the nearest milligram
in air (W1) and in distilled water (W2) at room temperature. If wetting
is necessary to remove air bubbles, dip the specimen in acetone and
thoroughly rinse it with distilled water.
(b) Immerse each specimen in ASTM No. 3 oil for 70 hours at 212
[deg]F. and then cool in ASTM No. 3 oil at room temperature for 30 to 60
minutes.
(c) Dip the specimen quickly in acetone and blot it lightly with
filter paper.
(d) Weigh each specimen in a tared weighing bottle (W3) and in
distilled water (W4) within five minutes of removal from the cooling
liquid.
(e) Calculate the percentage increase in volume follows:
Percent of increase=
[(W3-W4)-(W1-W2)]/
(W1-W2)x100
S8.4 Ozone resistance test. Conduct the test specified in S6.8 using
air brake hose.
S8.5 Length change test. (a) Position a test hose in a straight,
horizontal position, and apply air pressure of 10 psi thereto.
(b) Measure the hose to determine original free length.
(c) Without releasing the 10 psi, raise the air pressure to the test
hose to 200 psi.
(d) Measure the hose under 200 psi to determine final free length.
An elongation or contraction is an increase or decrease, respectively,
in the final free length from the original free length of the hose.
S8.6 Adhesion test.
S8.6.1 Apparatus. A tension testing machine that is power-driven and
that applies a constant rate of extension is used for measuring the
force required to separate the layers of the test specimen. The
apparatus is constructed so that:
(a) The recording head includes a freely rotating form with an
outside diameter substantially the same as the inside diameter of the
hose specimen to be placed on it.
(b) The freely rotating form is mounted so that its axis of rotation
is in the plane of the ply being separated from the specimen and so that
the applied force is perpendicular to the tangent of the specimen
circumference at the line of separation.
(c) The rate of travel of the power-actuated grip is a uniform one
inch per minute and the capacity of the machine is such that maximum
applied tension during the test is not more than 85 percent nor less
than 15 percent of the machine's rated capacity.
(d) The machine produces a chart with separation as one coordinate
and applied tension as the other.
S8.6.2 Preparation. (a) Cut a test specimen of 1 inch or more in
length from the hose to be tested and cut the layer to be tested of that
test specimen longitudinally along its entire length to the level of
contact with the adjacent layer.
(b) Peel the layer to be tested from the adjacent layer to create a
flap large enough to permit attachment of the power-actuated clamp of
the apparatus.
(c) Mount the test specimen on the freely rotating form with the
separated layer attached to the power-actuated clamp.
[[Page 235]]
S8.6.3 [Reserved]
S8.6.4 Calculations. (a) The adhesion value shall be the minimum
force recorded on the chart excluding that portion of the chart which
corresponds to the initial and final 20 percent portion along the
displacement axis.
(b) Express the force in pounds per inch of length.
S8.7 Air pressure test. (a) Connect the air brake hose assembly to a
source of air pressure.
(b) Apply 200 psi air pressure to the hose and seal the hose from
the source of air pressure.
(c) After 5 minutes, determine the air pressure remaining in the
test specimen.
S8.8 Burst strength test. (a) Utilize an air brake hose assembly.
(b) Fill the hose assembly with water, allowing all gases to escape.
Apply water pressure at a uniform rate of increase of approximately
1,000 psi per minute until the hose ruptures.
S8.9 Tensile strength test. Utilize a tension testing machine
conforming to the requirements of the Methods of Verification of Testing
Machines (1964 American Society for Testing and Materials, Designation
E4), and provided with a recording device to register total pull in
pounds.
(a) Attach an air brake hose assembly to the testing machine to
permit straight, even, machine-pull on the hose.
(b) Apply tension at a rate of 1 inch per minute travel of the
moving head until separation occurs.
S8.10 Water Absorption and tensile strength test. Immerse an air
brake hose assembly in distilled water at room temperature for 70 hours.
Thirty minutes after removal from the water, conduct the test specified
in S8.9.
S8.11 Zinc chloride resistance test. Immerse an air brake hose in a
50 percent zinc chloride aqueous solution at room temperature for 200
hours. Remove it from the solution and examine it under 7-power
magnification for cracks.
S8.12 End fitting corrosion resistance test. Conduct the test
specified in S6.9 using an air brake hose assembly.
S9. Requirements--vacuum brake hose, brake hose assemblies, and
brake hose end fittings.
S9.1 Labeling.
S9.1.1 Hose. Each vacuum brake hose shall be labeled, or cut from
bulk hose that is labeled, at intervals of not more than 6 inches,
measured from the end of one legend to the beginning of the next, in
block capital letters and numerals at least one-eighth of an inch high,
with the information listed in paragraphs (a) through (e) of this
section. The information need not be present on hose that is sold as
part of a brake hose assembly or a motor vehicle. (a) The symbol DOT,
constituting a certification by the hose manufacturer that the hose
conforms to all applicable motor vehicle safety standards.
(b) A designation that identifies the manufacturer of the hose,
which shall be filed in writing with: Office of Crash Avoidance
Standards, Vehicle Dynamics Division, National Highway Traffic Safety
Administration, 400 Seventh Street, SW., Washington, DC 20590. The
designation may consist of block capital letters, numerals or a symbol.
(c) The month, day, and year, or the month and year, of manufacture,
expressed in numerals. For example, 10/1/96 means October 1, 1996.
(d) The nominal inside diameter of the hose expressed in inches or
fractions of inches or in millimeters, or the nominal outside diameter
of plastic tubing expressed in inches or fractions of inches or in
millimeters followed by the letters OD. The abbreviation ``mm'' shall
follow hose sizes that are expressed in millimeters. (Example of inside
diameter: \7/32\, \1/4\, 4 mm. Example of outside diameter: \1/4\ OD, 12
mm OD.)
(e) The letters ``VL'' or ``VH'' shall indicate that the component
is a light-duty vacuum brake hose or heavy-duty vacuum brake hose,
respectively.
S9.1.2 End fittings. Except for an end fitting that is attached by
heat striking or by interference fit with plastic vacuum hose or that is
attached by deformation of the fitting about a hose by crimping or
swaging, at least one component of each vacuum brake hose fitting shall
be etched, embossed, or stamped in block capital letters and numerals at
least one-sixteenth of an inch high with the following information:
(a) The symbol DOT, constituting a certification by the manufacturer
of that component that the component
[[Page 236]]
conforms to all applicable motor vehicle safety standards.
(b) A designation that identifies the manufacturer of that component
of the fitting, which shall be filed in writing with: Office of Crash
Avoidance Standards, Vehicle Dynamics Division, National Highway Traffic
Safety Administration, 400 Seventh Street, SW., Washington, DC 20590.
The designation may consist of block capital letters, numerals or a
symbol.
(c) The letters ``VL'' or ``VH'' shall indicate that the end fitting
is intended for use in a light-duty or heavy-duty vacuum brake system,
respectively.
(d) The nominal inside diameter of the hose to which the fitting is
properly attached expressed in inches or fractions of inches or in
millimeters, or the outside diameter of the plastic tubing to which the
fitting is properly attached expressed in inches or fraction of inches
or in millimeters followed by the letter OD (See examples in S9.1.1(d)).
The abbreviation ``mm'' shall follow hose sizes that are expressed in
millimeters.
S9.1.3 Assemblies. Each vacuum brake hose assembly made with end
fittings that are attached by crimping or swaging and each plastic tube
assembly made with end fittings that are attached by heat shrinking or
dimensional interference fit, except those sold as part of a motor
vehicle, shall be labeled by means of a band around the brake hose
assembly as specified in this paragraph or, at the option of the
manufacturer, by means of labeling as specified in S9.1.3.1. The band
may at the manufacturer's option be attached so as to move freely along
the length of the assembly, as long as it is retained by the end
fittings. The band shall be etched, embossed, or stamped in block
capital letters, numerals or symbols at least one-eighth of an inch
high, with the following information:
(a) The symbol DOT, constituting certification by the hose assembler
that the hose assembly conforms to all applicable motor vehicle safety
standards.
(b) A designation that identifies the manufacturer of the hose
assembly, which shall be filed in writing with: Office of Crash
Avoidance Standards, Vehicle Dynamics Division, National Highway Traffic
Safety Administration, 400 Seventh Street SW., Washington, DC 20590. The
designation may consist of block capital letters, numerals or a symbol.
S9.1.3.1 At least one end fitting of a vacuum brake hose assembly
made with end fittings that are attached by crimping or swaging, or of a
plastic tubing assembly made with end fittings that are attached by heat
shrinking or dimensional interference fit shall be etched, stamped or
embossed with a designation at least one-sixteenth of an inch high that
identifies the manufacturer of the hose assembly and is filed in
accordance with S9.1.3(b).
S9.2 Test requirements. Each vacuum brake hose assembly or
appropriate part thereof shall be capable of meeting any of the
requirements set forth under this heading, when tested under the
conditions of S11. and the applicable procedures of S10. However, a
particular hose assembly or appropriate part thereof need not meet
further requirements after having met the construction requirement
(S9.2.1) and then having been subjected to any one of the requirements
specified in S9.2.2 through S9.2.11.
S9.2.1 Constriction. Except for that part of an end fitting which
does not contain hose, every inside diameter of any section of a vacuum
brake hose assembly shall be not less than 75 percent of the nominal
inside diameter of the hose if for heavy duty, or 70 percent of the
nominal inside diameter of the hose if for light duty.
S9.2.2 High temperature resistance. A vacuum brake hose shall not
show external or internal cracks, charring, or disintegration visible
without magnification when straightened after being bent for 70 hours at
212 [deg]F. over a cylinder having the radius specified in Table V for
the size of hose tested (S10.1).
S9.2.3 Low temperature resistance. A vacuum brake hose shall not
show cracks visible without magnification after conditioning at minus 40
[deg]F. for 70 hours when bent around a cylinder having the radius
specified in Table V for the size hose tested (S10.2).
[[Page 237]]
S9.2.4 Ozone resistance. A vacuum brake hose shall not show cracks
visible under 7-power magnification after exposure to ozone for 70 hours
(S10.3).
S9.2.5 Burst strength. A vacuum brake hose shall not rupture under
hydrostatic pressure of 350 psi (S10.4).
S9.2.6 Vacuum. The collapse of the outside diameter of a vacuum
brake hose under internal vacuum of 26 inches of Hg. for five minutes
shall not exceed one-sixteenth of an inch (S10.5).
S9.2.7 Bend. The collapse of the outside diameter of a vacuum brake
hose at the middle point of the test length when bent until the ends
touch shall not exceed the values given in Table V for the size of hose
tested (S10.6).
Table V--Vacuum Brake Hose Test Requirements
----------------------------------------------------------------------------------------------------------------
Hose inside diameter* High temperature Low temperature Bend
---------------------- resistance resistance ----------------------
-------------------------------------------- Maximum Deformation--collapsed
Hose collapse inside diameter
Inches Millimeters Hose Radius of Hose Radius of length, of outside (dimension D), inches
length, cylinder, length, cylinder, inches diameter,
inches inches inches inches inches
----------------------------------------------------------------------------------------------------------------
\7/32\ 5 8 1\1/2\ 17\1/2\ 3 7 \11/64\ \3/64\
\1/4\ 6 9 1\1/2\ 17\1/2\ 3 8 \3/32\ \1/16\
\9/32\ ............ 9 1\3/4\ 19 3\1/2\ 9 \12/64\ \4/64\
\11/32\ 8 9 1\3/4\ 19 3\1/2\ 11 \13/64\ \5/64\
\3/8\ 10 10 1\3/4\ 19 3\1/2\ 12 \5/32\ \3/32\
\7/16\ ............ 11 2 20\1/2\ 4 14 \17/64\ \5/64\
\15/32\ ............ 11 2 20\1/2\ 4 14 \17/64\ \5/64\
\1/2\ 12 11 2 20\1/2\ 4 16 \7/32\ \1/8\
\5/8\ 16 12 2\1/4\ 22 4\1/2\ 22 \7/32\ \5/32\
\3/4\ ............ 14 2\1/2\ 24 5 28 \7/32\ \3/16\
1 ............ 16 3\1/4\ 28\1/2\ 6\1/2\ 36 \9/32\ \1/4\
----------------------------------------------------------------------------------------------------------------
*These sizes are listed to provide test values for brake hoses manufactured in these sizes. They do not
represent conversions.
S9.2.8 Swell. Following exposure to Reference Fuel A, every inside
diameter of any section of a vacuum brake hose shall not be less than 75
percent of the nominal inside of the hose if for heavy duty, or 70
percent of the nominal inside diameter of the hose if for light duty.
The vacuum brake hose shall show no leakage and there shall be no
separation of the inner tube from the fabric reinforcement of the hose
in a vacuum test of 26 inches of Hg for 10 minutes (S10.7).
S9.2.9 Adhesion. Except for hose reinforced by wire, a vacuum brake
hose shall withstand a force of 8 pounds per inch of length before
separation of adjacent layers (S10.8).
S9.2.10 Deformation. A vacuum brake hose shall return to 90 percent
of its original outside diameter within 60 seconds after five
applications of force as specified in S10.9, except that a wire-
reinforced hose need only return to 85 percent of its original outside
diameter. In the case of heavy-duty hose the first application of force
shall not exceed a peak value of 70 pounds, and the fifth application of
force shall reach a peak value of at least 40 pounds. In the case of
lightduty hose the first application of force shall not exceed a peak
value of 50 pounds, and the fifth application of force shall reach a
peak value of at least 20 pounds (S10.9).
S9.2.11 End fitting corrosion resistance. After 24 hours of exposure
to salt spray, vacuum brake hose end fittings shall show no base metal
corrosion of the end fitting surface except where crimping or the
application of labeling information has caused displacement of the
protective coating.
S10. Test procedures--Vacuum brake hose, brake hose assemblies, and
brake hose end fittings.
S10.1 High temperature resistance test. Conduct the test specified
in S8.1 using vacuum brake hose with the cylinder radius specified in
Table V for the size of hose tested.
S10.2 Low temperature resistance test. Conduct the test specified in
S8.2 using vacuum brake hose with the cylinder radius specified in Table
V for the size of hose tested.
S10.3 Ozone resistance test. Conduct the test specified in S6.8
using vacuum brake hose.
[[Page 238]]
S10.4 Burst strength test. Conduct the test specified in S8.8 using
vacuum brake hose.
S10.5 Vacuum test. Utilize a 12-inch vacuum brake hose assembly
sealed at one end. (a) Measure the hose outside diameter.
(b) Attach the hose to a source of vacuum and subject it to a vacuum
of 26 inches of Hg for 5 minutes.
(c) Measure the hose to determine the minimum outside diameter while
the hose is still subject to vacuum.
S10.6 Bend test. (a) Bend a vacuum brake hose, of the length
prescribed in Table V, in the direction of its normal curvature until
the ends just touch as shown in Figure 3.
(b) Measure the outside diameter of the specimen at point A before
and after bending.
(c) The difference between the two measurements is the collapse of
the hose outside diameter on bending.
[GRAPHIC] [TIFF OMITTED] TC01AU91.008
Fig. 3--Bend Test of Vacuum Brake Hose.
S10.7 Swell test. (a) Fill a specimen of vacuum brake hose 12 inches
long with Reference Fuel A as described in the Method of Test for Change
in Properties of Elastomeric Vulcanizers Resulting From Immersion in
Liquids (1964 American Society for Testing and Materials, designation
D471).
(b) Maintain reference fuel in the hose under atmospheric pressure
at room temperature for 48 hours.
(c) Remove fuel and determine that every inside diameter of any
section of the brake hose is not less than 75 percent of the nominal
inside diameter of the hose for heavy-duty hose and 70 percent of the
nominal inside diameter of the hose for light-duty hose.
(d) Subject the hose specimen to a vacuum of 26 inches of Hg for 10
minutes.
S10.8 Adhesion test. Conduct the test specified in S8.6 using vacuum
brake hose.
S10.9 Deformation test. Table VI specifies the test specimen
dimensions.
S10.9.1 Apparatus. Utilize a compression device, equipped to measure
force of at least 100 pounds, and feeler gages of sufficient length to
be passed completely through the test specimen.
S10.9.2 Operation. (a) Position the test specimen longitudinally in
the compression device with the fabric laps not in the line of the
applied pressure.
Table VI--Dimensions of Test Specimen and Feeler Gage for Deformation
Test
------------------------------------------------------------------------
Hose inside diameter* Specimen dimensions Feeler gage dimensions
---------------------- (see fig. 4) --------------------------
------------------------
In. Mm. Depth Length Width Thickness
(inch) (inch) (inch) (inch)
------------------------------------------------------------------------
\7/32\ 5 \3/64\ 1 \1/8\ \3/64\
\1/4\ 6 \1/16\ 1 \1/8\ \1/16\
\9/32\ ......... \1/16\ 1 \1/8\ \1/16\
\11/32\ 8 \5/64\ 1 \3/16\ \5/64\
\3/8\ 10 \3/32\ 1 \3/16\ \3/32\
\7/16\ ......... \5/64\ 1 \1/4\ \5/64\
\15/32\ ......... \5/64\ 1 \1/4\ \5/64\
\1/2\ 12 \1/8\ 1 \1/4\ \1/8\
\5/8\ 16 \5/32\ 1 \1/4\ \5/32\
\3/4\ ......... \3/16\ 1 \1/4\ \3/16\
1 ......... \1/4\ 1 \1/4\ \1/4\
------------------------------------------------------------------------
*These sizes are listed to provide test values for brake hoses
manufactured in these sizes. They do not represent conversions.
(b) Apply gradually increasing force to the test specimen to
compress its inside diameter to that specified in Table VI (dimension D
of figure 4) for the size of hose tested.
[GRAPHIC] [TIFF OMITTED] TC01AU91.009
Fig. 4--Deformed Specimen of Vacuum Brake Hose
(c) After 5 seconds release the force and record the peak load
applied.
(d) Repeat the procedure four times permitting a 10-second recovery
period between load applications.
[[Page 239]]
S10.10 End fitting corrosion resistance test. Conduct the test
specified in S6.9 using a vacuum brake hose assembly.
S11. Test conditions. Each hose assembly or appropriate part thereof
shall be able to meet the requirements of S5., S7., and S9. under the
following conditions.
S11.1 The temperature of the testing room is 75 [deg]F.
S11.2 Except for S6.6, S8.2, and S10.2, the test samples are
stabilized at test room temperature prior to testing.
S11.3 The brake hoses and brake hose assemblies are at least 24
hours old, and unused.
[38 FR 31303, Nov. 13, 1973]
Editorial Note: For Federal Register citations affecting Sec.
571.106, see the List of CFR Sections Affected, which appears in the
Finding Aids section of the printed volume and on GPO Access.