[Code of Federal Regulations] [Title 14, Volume 2] [Revised as of January 1, 2005] From the U.S. Government Printing Office via GPO Access [CITE: 14CFR121.1] [Page 403-419] TITLE 14--AERONAUTICS AND SPACE CHAPTER I--FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) PART 121_OPERATING REQUIREMENTS: DOMESTIC, FLAG, AND SUPPLEMENTAL OPERATIONS--Table of Contents Subpart A_General Sec. 121.1 Applicability. Special Federal Aviation Regulation No. 14 Special Federal Aviation Regulation No. 36 Special Federal Aviation Regulation No. 50-2 [Note] [[Page 404]] Special Federal Aviation Regulation No. 58 Special Federal Aviation Regulation No. 71 [Note] Special Federal Aviation Regulation No. 78 [Note] Special Federal Aviation Regulation No. 80 Special Federal Aviation Regulation No. 92-5 Special Federal Aviation Regulation No. 93 [Note] Special Federal Aviation Regulation No. 97 [Note] Subpart A_General Sec. 121.1 Applicability. 121.2 Compliance schedule for operators that transition to part 121; certain new entrant operators. 121.4 Applicability of rules to unauthorized operators. 121.11 Rules applicable to operations in a foreign country. 121.15 Carriage of narcotic drugs, marihuana, and depressant or stimulant drugs or substances. Subpart B--Certification Rules for Domestic and Flag Air Carriers [Reserved] Subpart C--Certification Rules for Supplemental Air Carriers and Commercial Operators [Reserved] Subpart D--Rules Governing All Certificate Holders Under This Part [Reserved] Subpart E_Approval of Routes: Domestic and Flag Operations 121.91 Applicability. 121.93 Route requirements: General. 121.95 Route width. 121.97 Airports: Required data. 121.99 Communication facilities. 121.101 Weather reporting facilities. 121.103 En route navigational facilities. 121.105 Servicing and maintenance facilities. 121.107 Dispatch centers. Subpart F_Approval of Areas and Routes for Supplemental Operations 121.111 Applicability. 121.113 Area and route requirements: General. 121.115 Route width. 121.117 Airports: Required data. 121.119 Weather reporting facilities. 121.121 En route navigational facilities. 121.123 Servicing maintenance facilities. 121.125 Flight following system. 121.127 Flight following system; requirements. Subpart G_Manual Requirements 121.131 Applicability. 121.133 Preparation. 121.135 Contents. 121.137 Distribution and availability. 121.139 Requirements for manual aboard aircraft: Supplemental operations. 121.141 Airplane flight manual. Subpart H_Aircraft Requirements 121.151 Applicability. 121.153 Aircraft requirements: General. 121.155 [Reserved] 121.157 Aircraft certification and equipment requirements. 121.159 Single-engine airplanes prohibited. 121.161 Airplane limitations: Type of route. 121.163 Aircraft proving tests. Subpart I_Airplane Performance Operating Limitations 121.171 Applicability. 121.173 General. 121.175 Airplanes: Reciprocating engine-powered: Weight limitations. 121.177 Airplanes: Reciprocating engine-powered: Takeoff limitations. 121.179 Airplanes: Reciprocating engine-powered: En route limitations: All engines operating. 121.181 Airplanes: Reciprocating engine-powered: En route limitations: One engine inoperative. 121.183 Part 25 airplanes with four or more engines: Reciprocating engine powered: En route limitations: Two engines inoperative. 121.185 Airplanes: Reciprocating engine-powered: Landing limitations: Destination airport. 121.187 Airplanes: Reciprocating engine-powered: Landing limitations: Alternate airport. 121.189 Airplanes: Turbine engine powered: Takeoff limitations. 121.191 Airplanes: Turbine engine powered: En route limitations: One engine inoperative. 121.193 Airplanes: Turbine engine powered: En route limitations: Two engines inoperative. 121.195 Airplanes: Turbine engine powered: Landing limitations: Destination airports. 121.197 Airplanes: Turbine engine powered: Landing limitations: Alternate airports. 121.198 Cargo service airplanes: Increased zero fuel and landing weights. 121.199 Nontransport category airplanes: Takeoff limitations. [[Page 405]] 121.201 Nontransport category airplanes: En route limitations: One engine inoperative. 121.203 Nontransport category airplanes: Landing limitations: Destination airport. 121.205 Nontransport category airplanes: Landing limitations: Alternate airport. 121.207 Provisionally certificated airplanes: Operating limitations. Subpart J_Special Airworthiness Requirements 121.211 Applicability. 121.213 [Reserved] 121.215 Cabin interiors. 121.217 Internal doors. 121.219 Ventilation. 121.221 Fire precautions. 121.223 Proof of compliance with Sec. 121.221. 121.225 Propeller deicing fluid. 121.227 Pressure cross-feed arrangements. 121.229 Location of fuel tanks. 121.231 Fuel system lines and fittings. 121.233 Fuel lines and fittings in designated fire zones. 121.235 Fuel valves. 121.237 Oil lines and fittings in designated fire zones. 121.239 Oil valves. 121.241 Oil system drains. 121.243 Engine breather lines. 121.245 Fire walls. 121.247 Fire-wall construction. 121.249 Cowling. 121.251 Engine accessory section diaphragm. 121.253 Powerplant fire protection. 121.255 Flammable fluids. 121.257 Shutoff means. 121.259 Lines and fittings. 121.261 Vent and drain lines. 121.263 Fire-extinguishing systems. 121.265 Fire-extinguishing agents. 121.267 Extinguishing agent container pressure relief. 121.269 Extinguishing agent container compartment temperature. 121.271 Fire-extinguishing system materials. 121.273 Fire-detector systems. 121.275 Fire detectors. 121.277 Protection of other airplane components against fire. 121.279 Control of engine rotation. 121.281 Fuel system independence. 121.283 Induction system ice prevention. 121.285 Carriage of cargo in passenger compartments. 121.287 Carriage of cargo in cargo compartments. 121.289 Landing gear: Aural warning device. 121.291 Demonstration of emergency evacuation procedures. 121.293 Special airworthiness requirements for nontransport category airplanes type certificated after December 31, 1964. Subpart K_Instrument and Equipment Requirements 121.301 Applicability. 121.303 Airplane instruments and equipment. 121.305 Flight and navigational equipment. 121.306 Portable electronic devices. 121.307 Engine instruments. 121.308 Lavatory fire protection. 121.309 Emergency equipment. 121.310 Additional emergency equipment. 121.311 Seats, safety belts, and shoulder harnesses. 121.312 Materials for compartment interiors. 121.313 Miscellaneous equipment. 121.314 Cargo and baggage compartments. 121.315 Cockpit check procedure. 121.316 Fuel tanks. 121.317 Passenger information requirements, smoking prohibitions, and additional seat belt requirements. 121.318 Public address system. 121.319 Crewmember interphone system. 121.321 [Reserved] 121.323 Instruments and equipment for operations at night. 121.325 Instruments and equipment for operations under IFR or over-the- top. 121.327 Supplemental oxygen: Reciprocating engine powered airplanes. 121.329 Supplemental oxygen for sustenance: Turbine engine powered airplanes. 121.331 Supplemental oxygen requirements for pressurized cabin airplanes: Reciprocating engine powered airplanes. 121.333 Supplemental oxygen for emergency descent and for first aid; turbine engine powered airplanes with pressured cabins. 121.335 Equipment standards. 121.337 Protective breathing equipment. 121.339 Emergency equipment for extended over-water operations. 121.340 Emergency flotation means. 121.341 Equipment for operations in icing conditions. 121.342 Pitot heat indication systems. 121.343 Flight recorders. 121.344 Digital flight data recorders for transport category airplanes. 121.344a Digital flight data recorders for 10-19 seat airplanes. 121.345 Radio equipment. 121.347 Radio equipment for operations under VFR over routes navigated by pilotage. 121.349 Radio equipment for operations under VFR over routes not navigated by pilotage or for operations under IFR or over-the- top. 121.351 Radio equipment for extended overwater operations and for certain other operations. 121.353 Emergency equipment for operations over uninhabited terrain areas: Flag, [[Page 406]] supplemental, and certain domestic operators. 121.354 Terrain awareness and warning system. 121.355 Equipment for operations on which specialized means of navigation are used. 121.356 Collision Avoidance System. 121.357 Airborne weather radar equipment requirements. 121.358 Low-altitude windshear system equipment requirements. 121.359 Cockpit voice recorders. 121.360 Ground proximity warning-glide slope deviation alerting system. Subpart L_Maintenance, Preventive Maintenance, and Alterations 121.361 Applicability. 121.363 Responsibility for airworthiness. 121.365 Maintenance, preventive maintenance, and alteration organization. 121.367 Maintenance, preventive maintenance, and alterations programs. 121.368 Aging airplane inspections and records reviews. 121.369 Manual requirements. 121.370 Special maintenance program requirements. 121.370a Supplemental inspections. 121.371 Required inspection personnel. 121.373 Continuing analysis and surveillance. 121.375 Maintenance and preventive maintenance training program. 121.377 Maintenance and preventive maintenance personnel duty time limitations. 121.378 Certificate requirements. 121.379 Authority to perform and approve maintenance, preventive maintenance, and alterations. 121.380 Maintenance recording requirements. 121.380a Transfer of maintenance records. Subpart M_Airman and Crewmember Requirements 121.381 Applicability. 121.383 Airman: Limitations on use of services. 121.385 Composition of flight crew. 121.387 Flight engineer. 121.389 Flight navigator and specialized navigation equipment. 121.391 Flight attendants. 121.393 Crewmember requirements at stops where passengers remain on board. 121.395 Aircraft dispatcher: Domestic and flag operations. 121.397 Emergency and emergency evacuation duties. Subpart N_Training Program 121.400 Applicability and terms used. 121.401 Training program: General. 121.402 Training program: Special rules. 121.403 Training program: Curriculum. 121.404 Compliance dates: Crew and dispatcher resource management training. 121.405 Training program and revision: Initial and final approval. 121.406 Credit for previous CRM/DRM training. 121.407 Training program: Approval of airplane simulators and other training devices. 121.409 Training courses using airplane simulators and other training devices. 121.411 Qualifications: Check airmen (airplane) and check airmen (simulator). 121.412 Qualifications: Flight instructors (airplane) and flight instructors (simulator). 121.413 Initial and transition training and checking requirements: Check airmen (airplane), check airmen (simulator). 121.414 Initial and transition training and checking requirements: flight instructors (airplane), flight instructors (simulator). 121.415 Crewmember and dispatcher training requirements. 121.417 Crewmember emergency training. 121.418 Differences training: Crewmembers and dispatchers. 121.419 Pilots and flight engineers: Initial, transition, and upgrade ground training. 121.420 Flight navigators: Initial and transition ground training. 121.421 Flight attendants: Initial and transition ground training. 121.422 Aircraft dispatchers: Initial and transition ground training. 121.424 Pilots: Initial, transition and upgrade flight training. 121.425 Flight engineers: Initial and transition flight training. 121.426 Flight navigators: Initial and transition flight training. 121.427 Recurrent training. 121.429 Prohibited drugs. Subpart O_Crewmember Qualifications 121.431 Applicability. 121.432 General. 121.433 Training required. 121.433a Training requirements: Handling and carriage of dangerous articles and magnetized materials. 121.434 Operating experience, operating cycles, and consolidation of knowledge and skills. 121.437 Pilot qualification: Certificates required. 121.438 Pilot operating limitations and pairing requirements. 121.439 Pilot qualification: Recent experience. 121.440 Line checks. 121.441 Proficiency checks. 121.443 Pilot in command qualification: Route and airports. [[Page 407]] 121.445 Pilot in command airport qualification: Special areas and airports. 121.447 [Reserved] 121.453 Flight engineer qualifications. 121.455 Use of prohibited drugs. 121.457 Testing for prohibited drugs. 121.458 Misuse of alcohol. 121.459 Testing for alcohol. Subpart P_Aircraft Dispatcher Qualifications and Duty Time Limitations: Domestic and Flag Operations; Flight Attendant Duty Period Limitations and Rest Requirements: Domestic, Flag, and Supplemental Operations 121.461 Applicability. 121.463 Aircraft dispatcher qualifications. 121.465 Aircraft dispatcher duty time limitations: Domestic and flag operations. 121.467 Flight attendant duty period limitations and rest requirements: Domestic, flag, and supplemental operations. Subpart Q_Flight Time Limitations and Rest Requirements: Domestic Operations 121.470 Applicability. 121.471 Flight time limitations and rest requirements: All flight crewmembers. Subpart R_Flight Time Limitations: Flag Operations 121.480 Applicability. 121.481 Flight time limitations: One or two pilot crews. 121.483 Flight time limitations: Two pilots and one additional flight crewmember. 121.485 Flight time limitations: Three or more pilots and an additional flight crewmember. 121.487 Flight time limitations: Pilots not regularly assigned. 121.489 Flight time limitations: Other commercial flying. 121.491 Flight time limitations: Deadhead transportation. 121.493 Flight time limitations: Flight engineers and flight navigators. Subpart S_Flight Time Limitations: Supplemental Operations 121.500 Applicability. 121.503 Flight time limitations: Pilots: airplanes. 121.505 Flight time limitations: Two pilot crews: airplanes. 121.507 Flight time limitations: Three pilot crews: airplanes. 121.509 Flight time limitations: Four pilot crews: airplanes. 121.511 Flight time limitations: Flight engineers: airplanes. 121.513 Flight time limitations: Overseas and international operations: airplanes. 121.515 Flight time limitations: All airmen: airplanes. 121.517 Flight time limitations: Other commercial flying: airplanes. 121.519 Flight time limitations: Deadhead transportation: airplanes. 121.521 Flight time limitations: Crew of two pilots and one additional airman as required. 121.523 Flight time limitations: Crew of three or more pilots and additional airmen as required. 121.525 Flight time limitations: Pilots serving in more than one kind of flight crew. Subpart T_Flight Operations 121.531 Applicability. 121.533 Responsibility for operational control: Domestic operations. 121.535 Responsibility for operational control: Flag operations. 121.537 Responsibility for operational control: Supplemental operations. 121.538 Aircraft security. 121.539 Operations notices. 121.541 Operations schedules: Domestic and flag operations. 121.542 Flight crewmember duties. 121.543 Flight crewmembers at controls. 121.545 Manipulation of controls. 121.547 Admission to flight deck. 121.548 Aviation safety inspector's credentials: Admission to pilot's compartment. 121.548a DOD Commercial Air Carrier Evaluator's Credential. 121.549 Flying equipment. 121.550 Secret Service Agents: Admission to flight deck. 121.551 Restriction or suspension of operation: Domestic and flag operations. 121.553 Restriction or suspension of operation: Supplemental operations. 121.555 Compliance with approved routes and limitations: Domestic and flag operations. 121.557 Emergencies: Domestic and flag operations. 121.559 Emergencies: Supplemental operations. 121.561 Reporting potentially hazardous meteorological conditions and irregularities of ground and navigation facilities. 121.563 Reporting mechanical irregularities. 121.565 Engine inoperative: Landing; reporting. 121.567 Instrument approach procedures and IFR landing minimums. 121.569 Equipment interchange: Domestic and flag operations. 121.570 Airplane evacuation capability. 121.571 Briefing passengers before takeoff. 121.573 Briefing passengers: Extended overwater operations. 121.574 Oxygen for medical use by passengers. 121.575 Alcoholic beverages. [[Page 408]] 121.576 Retention of items of mass in passenger and crew compartments. 121.577 Stowage of food, beverage, and passenger service equipment during airplane movement on the surface, takeoff, and landing. 121.578 Cabin ozone concentration. 121.579 Minimum altitudes for use of auto-pilot. 121.580 Prohibition on interference with crewmembers. 121.581 Observer's seat: En route inspections. 121.583 Carriage of persons without compliance with the passenger- carrying requirements of this part. 121.585 Exit seating. 121.586 Authority to refuse transportation. 121.587 Closing and locking of flight crew compartment door. 121.589 Carry-on baggage. 121.590 Use of certificated land airports in the United States. Subpart U_Dispatching and Flight Release Rules 121.591 Applicability. 121.593 Dispatching authority: Domestic operations. 121.595 Dispatching authority: Flag operations. 121.597 Flight release authority: Supplemental operations. 121.599 Familiarity with weather conditions. 121.601 Aircraft dispatcher information to pilot in command: Domestic and flag operations. 121.603 Facilities and services: Supplemental operations. 121.605 Airplane equipment. 121.607 Communication and navigation facilities: Domestic and flag operations. 121.609 Communication and navigation facilities: Supplemental operations. 121.611 Dispatch or flight release under VFR. 121.613 Dispatch or flight release under IFR or over the top. 121.615 Dispatch or flight release over water: Flag and supplemental operations. 121.617 Alternate airport for departure. 121.619 Alternate airport for destination: IFR or over-the-top: Domestic operations. 121.621 Alternate airport for destination: Flag operations. 121.623 Alternate airport for destination: IFR or over-the-top: Supplemental operations. 121.625 Alternate airport weather minimums. 121.627 Continuing flight in unsafe conditions. 121.628 Inoperable instruments and equipment. 121.629 Operation in icing conditions. 121.631 Original dispatch or flight release, redispatch or amendment of dispatch or flight release. 121.633 [Reserved] 121.635 Dispatch to and from refueling or provisional airports: Domestic and flag operations. 121.637 Takeoffs from unlisted and alternate airports: Domestic and flag operations. 121.639 Fuel supply: All domestic operations. 121.641 Fuel supply: Nonturbine and turbo-propeller-powered airplanes: Flag operations. 121.643 Fuel supply: Nonturbine and turbo-propeller-powered airplanes: Supplemental operations. 121.645 Fuel supply: Turbine-engine powered airplanes, other than turbo propeller: Flag and supplemental operations. 121.647 Factors for computing fuel required. 121.649 Takeoff and landing weather minimums: VFR: Domestic operations. 121.651 Takeoff and landing weather minimums: IFR: All certificate holders. 121.652 Landing weather minimums: IFR: All certificate holders. 121.653 [Reserved] 121.655 Applicability of reported weather minimums. 121.657 Flight altitude rules. 121.659 Initial approach altitude: Domestic and supplemental operations. 121.661 Initial approach altitude: Flag operations. 121.663 Responsibility for dispatch release: Domestic and flag operations. 121.665 Load manifest. 121.667 Flight plan: VFR and IFR: Supplemental operations. Subpart V_Records and Reports 121.681 Applicability. 121.683 Crewmember and dispatcher record. 121.685 Aircraft record: Domestic and flag operations. 121.687 Dispatch release: Flag and domestic operations. 121.689 Flight release form: Supplemental operations. 121.691 [Reserved] 121.693 Load manifest: All certificate holders. 121.695 Disposition of load manifest, dispatch release, and flight plans: Domestic and flag operations. 121.697 Disposition of load manifest, flight release, and flight plans: Supplemental operations. 121.698-121.699 [Reserved] 121.701 Maintenance log: Aircraft. 121.703 Mechanical reliability reports. 121.704 Service difficulty reports (structural). [[Page 409]] 121.705 Mechanical interruption summary report. 121.707 Alteration and repair reports. 121.709 Airworthiness release or aircraft log entry. 121.711 Communication records: Domestic and flag operations. 121.713 Retention of contracts and amendments: Commercial operators who conduct intrastate operations for compensation or hire. Subpart W_Crewmember Certificate: International 121.721 Applicability. 121.723 Surrender of international crewmember certificate. Subpart X_Emergency Medical Equipment and Training 121.801 Applicability. 121.803 Emergency medical equipment. 121.805 Crewmember training for in-flight medical events. Appendix A to Part 121--First-Aid Kits and Emergency Medical Kits Appendix B to Part 121--Aircraft Flight Recorder Specifications Appendix C to Part 121--C-46 Nontransport Category Airplanes Appendix D to Part 121--Criteria for Demonstration of Emergency Evacuation Procedures Under Sec. 121.291 Appendix E to Part 121--Flight Training Requirements Appendix F to Part 121--Proficiency Check Requirements Appendix G to Part 121--Doppler Radar and Inertial Navigation System (INS): Request for Evaluation; Equipment and Equipment Installation; Training Program; Equipment Accuracy and Reliability; Evaluation Program Appendix H to Part 121--Advanced Simulation Appendix I to Part 121--Drug Testing Program Appendix J to Part 121--Alcohol Misuse Prevention Program Appendix K to Part 121--Performance Requirements for Certain Turbopropeller Powered Airplanes Appendix L to Part 121--Type Certification Regulations Made Previously Effective Appendix M to Part 121--Airplane Flight Recorder Specifications Appendix N to Part 121--Design-Life Goals Authority: 49 U.S.C. 106(g), 40113, 40119, 41706, 44101, 44701- 44702, 44705, 44709-44711, 44713, 44716-44717, 44722, 44901, 44903- 44904, 44912, 45101-45105, 46105, 46301. Special Federal Aviation Regulation No. 14 Contrary performance provisions of the Civil Air Regulations notwithstanding, the Administrator may grant performance credit for the use of standby power on transport category airplanes. Such credit shall be applicable only to the maximum certificated take-off and landing weights, and the take-off distance, and the take-off paths, and shall not exceed that found by the Administrator to result in an over-all level of safety in the take-off, approach, and landing regimes of flight equivalent to that prescribed in the regulations under which the airplane was originally certificated without standby power. (Note: Standby power is power and/or thrust obtained from rocket engines for a relatively short period and actuated only in cases of emergency.) The following provisions shall apply: (1) Take-off; general. The take-off data prescribed in sections (2) and (3) shall be determined at all weights and altitudes, and at ambient temperatures if applicable, at which performance credit is to be applied. (2) Take-off path. (a) The one-engine-inoperative take-off path with standby power in use shall be determined in accordance with the performance requirements of the applicable airworthiness regulations. (b) The one-engine-inoperative take-off path (excluding that portion where the airplane is on or just above the take-off surface-determined in accordance with paragraph (a) of this section shall lie above the one/engine-inoperative take-off path without standby power at the maximum take/off weight at which all of the applicable airworthiness requirements are met. For the purpose of this comparison, the flight path shall be considered to extend to at least a height of 400 feet above the take-off surface. (c) The take-off path with all engines operating, but without the use of standby power, shall reflect a conservatively greater over-all level of performance than the one-engine-inoperative take-off path established in accordance with paragraph (a) of this section. The aforementioned margin shall be established by the Administrator to insure safe day-to-day operations, but in no case shall it be less than 15 percent. The all-engines-operating take-off path shall be determined by a procedure consistent with that established in complying with paragraph (a) of this section. (d) For reciprocating-engine-powered airplanes, the take-off path to be scheduled in the Airplane Flight Manual shall represent the one- engine-inoperative take-off path determined in accordance with paragraph (a) of this section and modified to reflect the procedure (see section (6)) established by the applicant for flap retraction and attainment of the en route speed. The scheduled take-off path shall have a positive slope at all points [[Page 410]] of the airborne portion and at no point shall it lie above the take-off path specified in paragraph (a) of this section. (3) Take-off distance. The take-off distance shall be the horizontal distance along the one/engine-inoperative take-off to the point where the airplane attains a height of 50 feet aove the take-off surface for reciprocating-engine-powered airplanes and a height of 35 feet above the take-off surface for turbine-powered airplanes. (4) Maximum certificated take-off weights. The maximum certificated take-off weights shall be determined at all altitudes, and at ambient temperatures if applicable, at which performance credit is to be applied and shall not exceed the weights established in compliance with paragraphs (a) and (b) of this section. (a) The conditions of section (2) (b) through (d) shall be met at the maximum certificated take-off weight. (b) Without the use of standby power, the airplane shall meet all of the en route requirements of the applicable airworthiness regulations under which the airplane was originally certificated. In addition, turbine-powered airplanes without the use of standby power shall meet the final take-off climb requirements prescribed in the applicable airworthiness regulations. (5) Maximum certificated landing weights. (a) The maximum certificated landing weights (one-engine/inoperative approach and all- engine/operating landing climb) shall be determined at all altitudes, and at ambient temperatures if applicable, at which performance credit is to be applied and shall not exceed that established in compliance with the provisions of paragraph (b) of this section. (b) The flight path, with the engines operating at the power and/or thrust appropriate to the airplane configuration and with standby power in use, shall lie above the flight path without standby power in use at the maximum weight at which all of the applicable airworthiness requirements are met. In addition, the flight paths shall comply with the provisions of paragraphs (i) and (ii) of this paragraph (b). (i) The flight paths shall be established without changing the appropriate airplane configuration. (ii) The flight paths shall be carried out for a minimum height of 400 feet above the point where standby power is actuated. (6) Airplane configuration, speed, and power and/or thrust; general. Any change in the airplane's configuration, speed, and power and/or thrust shall be made in accordance with the procedures established by the applicant for the operation of the airplane in service and shall comply with the provisions of paragraphs (a) through (c) of this section. In addition, procedures shall be established for the execution of balked landings and missed approaches. (a) The Administrator shall find that the procedure can be consistently executed in service by crews of average skill. (b) The procedure shall not involve methods or the use of devices which have not been proven to be safe and reliable. (c) Allowances shall be made for such time delays in the execution of the procedures as may be reasonably expected to occur during service. (7) Installation and operation; standby power. The standby power unit and its installation shall comply with the provisions of paragraphs (a) and (b) of this section. (a) The standby power unit and its installation shall not adversely affect the safety of the airplane. (b) The operation of the standby power unit and its control shall have proven to be safe and reliable. [23 FR 7454, Sept. 25, 1958. Redesignated at 29 FR 19099, Dec. 30, 1964] Special Federal Aviation Regulation No. 36 1. Definitions. For purposes of this Special Federal Aviation Regulation-- (a) A product is an aircraft, airframe, aircraft engine, propeller, or appliance; (b) An article is an airframe, powerplant, propeller, instrument, radio, or accessory; and (c) A component is a part of a product or article. 2. General. (a) Contrary provisions of Sec. 121.379(b) and Sec. 135.437(b) of this chapter notwithstanding, the holder of an air carrier certificate or operating certificate, that operates large aircraft, and that has been issued operations specifications for operations required to be conducted in accordance with 14 CFR part 121 or 135, may perform a major repair on a product as described in Sec. 121.379(b) or Sec. 135.437(a), using technical data that have not been approved by the Administrator, and approve that product for return to service, if authorized in accordance with this Special Federal Aviation Regulation. (b) [Reserved] (c) Contrary provisions of Sec. 145.201(c)(2) notwithstanding, the holder of a repair station certificate under 14 CFR part 145 that is located in the United States may perform a major repair on an article for which it is rated using technical data not approved by the FAA and approve that article for return to service, if authorized in accordance with this Special Federal Aviation Regulation. If the certificate holder holds a rating limited to a component of a product or article, the holder may not, by virtue of this Special Federal Aviation Regulation, approve that product or article for return to service. [[Page 411]] 3. Major Repair Data and Return to Service. (a) As referenced in section 2 of this Special Federal Aviation Regulation, a certificate holder may perform a major repair on a product or article using technical data that have not been approved by the Administrator, and approve that product or article for return to service, if the certificate holder-- (1) Has been issued an authorization under, and a procedures manual that complies with, Special Federal Aviation Regulation No. 36-8, effective on January 23, 2004; (2) Has developed the technical data in accordance with the procedures manual; (3) Has developed the technical data specifically for the product or article being repaired; and (4) Has accomplished the repair in accordance with the procedures manual and the procedures approved by the Administrator for the certificate. (b) For purposes of this section, an authorization holder may develop technical data to perform a major repair on a product or article and use that data to repair a subsequent product or article of the same type as long as the holder-- (1) Evaluates each subsequent repair and the technical data to determine that performing the subsequent repair with the same data will return the product or article to its original or properly altered condition, and that the repaired product or article conforms with applicable airworthiness requirements; and (2) Records each evaluation in the records referenced in paragraph (a) of section 13 of this Special Federal Aviation Regulation. 4. Application. The applicant for an authorization under this Special Federal Aviation Regulation must submit an application, in writing, and signed by an officer of the applicant, to the FAA Certificate Holding District Office charged with the overall inspection of the applicant's operations under its certificate. The application must contain-- (a) If the applicant is (1) The holder of an air carrier operating or commercial operating certificate, or the holder of an air taxi operating certificate that operates large aircraft, the-- (i) The applicant's certificate number; and (ii) The specific product(s) the applicant is authorized to maintain under its certificate, operations specifications, and maintenance manual; or (2) The holder of a domestic repair station certificate-- (i) The applicant's certificate number; (ii) A copy of the applicant's operations specifications; and (iii) The specific article(s) for which the applicant is rated; (b) The name, signature, and title of each person for whom authorization to approve, on behalf of the authorization holder, the use of technical data for major repairs is requested; and (c) The qualifications of the applicant's staff that show compliance with section 5 of this Special Federal Aviation Regulation. 5. Eligibility. (a) To be eligible for an authorization under this Special Federal Aviation Regulation, the applicant, in addition to having the authority to repair products or articles must-- (1) Hold an air carrier certificate or operating certificate, operate large aircraft, and have been issued operations specifications for operations required to be conducted in accordance with 14 CFR part 121 or 135, or hold a domestic repair station certificate under 14 CFR part 145; (2) Have an adequate number of sufficiently trained personnel in the United States to develop data and repair the products that the applicant is authorized to maintain under its operating certificate or the articles for which it is rated under its domestic repair station certificate; (3) Employ, or have available, a staff of engineering personnel that can determine compliance with the applicable airworthiness requirements of the Federal Aviation Regulations. (b) At least one member of the staff required by paragraph (a)(3) of this section must-- (1) Have a thorough working knowledge of the applicable requirements of the Federal Aviation Regulations; (2) Occupy a position on the applicant's staff that has the authority to establish a repair program that ensures that each repaired product or article meets the applicable requirements of the Federal Aviation Regulations; (3) Have at least one year of satisfactory experience in processing engineering work, in direct contact with the FAA, for type certification or major repair projects; and (4) Have at least eight years of aeronautical engineering experience (which may include the one year of experience in processing engineering work for type certification or major repair projects). (c) The holder of an authorization issued under this Special Federal Aviation Regulation shall notify the Administrator within 48 hours of any change (including a change of personnel) that could affect the ability of the holder to meet the requirements of this Special Federal Aviation Regulation. 6. Procedures Manual. (a) A certificate holder may not approve a product or article for return to service under section 2 of this Special Federal Aviation Regulation unless the holder-- (1) Has a procedures manual that has been approved by the Administrator as complying with paragraph (b) of this section; and (2) Complies with the procedures contained in this procedures manual. [[Page 412]] (b) The approved procedures manual must contain-- (1) The procedures for developing and determining the adequacy of technical data for major repairs; (2) The identification (names, signatures, and responsibilities) of officials and of each staff member described in section 5 of this Special Federal Aviation Regulation who-- (i) Has the authority to make changes in procedures that require a revision to the procedures manual; and (ii) Prepares or determines the adequacy of technical data, plans or conducts tests, and approves, on behalf of the authorization holder, test results; and (3) A ``log of revisions'' page that identifies each revised item, page, and date of revision, and contains the signature of the person approving the change for the Administrator. (c) The holder of an authorization issued under this Special Federal Aviation Regulation may not approve a product or article for return to service after a change in staff necessary to meet the requirements of section 5 of this regulation or a change in procedures from those approved under paragraph (a) of this section, unless that change has been approved by the FAA and entered in the procedures manual. 7. Duration of Authorization. Each authorization issued under this Special Federal Aviation Regulation is effective from the date of issuance until January 23, 2009, unless it is earlier surrendered, suspended, revoked, or otherwise terminated. Upon termination of such authorization, the terminated authorization holder must: (a) Surrender to the FAA all data developed pursuant to Special Federal Aviation Regulation No. 36; or (b) Maintain indefinitely all data developed pursuant to Special Federal Aviation Regulation No. 36, and make that data available to the FAA for inspection upon request. 8. Transferability. An authorization issued under this Special Federal Aviation Regulation is not transferable. 9. Inspections. Each holder of an authorization issued under this Special Federal Aviation Regulation and each applicant for an authorization must allow the Administrator to inspect its personnel, facilities, products and articles, and records upon request. 10. Limits of Applicability. An authorization issued under this Special Federal Aviation Regulation applies only to-- (a) A product that the air carrier, commercial, or air taxi operating certificate holder is authorized to maintain pursuant to its continuous airworthiness maintenance program or maintenance manual; or (b) An article for which the domestic repair station certificate holder is rated. If the certificate holder is rated for a component of an article, the holder may not, in accordance with this Special Federal Aviation Regulation, approve that article for return to service. 11. Additional Authorization Limitations. Each hold of a authorization issued under this Special Federal Aviation Regulation must comply with any additional limitations prescribed by the Administrator and made a part of the authorization. 12. Data Review and Service Experience. If the Administrator finds that a product or article has been approved for return to service after a major repair has been performed under this Special Federal Aviation Regulation, that the product or article may not conform to the applicable airworthiness requirements or that an unsafe feature or characteristic of the product or article may exist, and that the nonconformance or unsafe feature or characteristic may be attributed to the repair performed, the holder of the authorization, upon notification by the Administrator, shall-- (a) Investigate the matter; (b) Report to the Administrator the results of the investigation and any action proposed or taken; and (c) If notified that an unsafe condition exists, provide within the time period stated by the Administrator, the information necessary for the FAA to issue an airworthiness directive under part 39 of the Federal Aviation Regulations. 13. Current Records. Each holder of an authorization issued under this Special Federal Aviation Regulation shall maintain, at its facility, current records containing-- (a) For each product or article for which it has developed and used major repair data, a technical data file that includes all data and amendments thereto (including drawings, photographs, specifications, instructions, and reports) necessary to accomplish the major repair; (b) A list of products or articles by make, model, manufacturer's serial number (including specific part numbers and serial numbers of components) and, if applicable, FAA Technical Standard Order (TSO) or Parts Manufacturer Approval (PMA) identification, that have been repaired under the authorization; and (c) A file of information from all available sources on difficulties experienced with products and articles repaired under the authorization. This Special Federal Aviation Regulation terminates January 23, 2009. [SFAR 36-6, 59 FR 3940, Jan. 27, 1994, as amended by Amdt. SFAR 36-7, 64 FR 960, Jan. 6, 1999; Amdt. 121-286, 66 FR 41116, Aug. 6, 2001; Amdt. SFAR 36-8, 68 FR 65378, Nov. 19, 2003] [[Page 413]] Special Federal Aviation Regulation No. 50-2 Editorial Note: For the text of SFAR No. 50-2, see part 91 of this chapter. Special Federal Aviation Regulation No. 58--Advanced Qualification Program Section 1. Purpose and eligibility. 2. Definitions. 3. Required Curriculums. 4. Indoctrination Curriculums. 5. Qualification Curriculums. 6. Continuing Qualification Curriculums. 7. Other Requirements. 8. Certification. 9. Training Devices and Simulators. 10. Approval of Advanced Qualification Program. 11. Approval of Training, Qualification, or Evaluation by a Person Who Provides Training by Arrangement. 12. Recordkeeping requirements. 13. Expiration. Contrary provisions of parts 61, 63, 65, 121, and 135 of the Federal Aviation Regulations notwithstanding-- 1. Purpose and Eligibility. (a) This Special Federal Aviation Regulation provides for approval of an alternate method (known as ''Advanced Qualification Program'' or ``AQP'') for qualifying, training, certifying, and otherwise ensuring competency of crewmembers, aircraft dispatchers, other operations personnel, instructors, and evaluators who are required to be trained or qualified under parts 121 and 135 of the FAR or under this SFAR. (b) A certificate holder is eligible under this Special Federal Aviation Regulation if the certificate holder is required to have an approved training program under Sec. 121.401 or Sec. 135.341 of the FAR, or elects to have an approved training program under Sec. 135.341. (c) A certificate holder obtains approval of each proposed curriculum under this AQP as specified in section 10 of this SFAR. (d) A curriculum approved under the AQP may include elements of present part 121 and part 135 training programs. Each curriculum must specify the make, model, and series aircraft (or variant) and each crewmember position or other positions to be covered by that curriculum. Positions to be covered by the AQP must include all flight crewmember positions, instructors, and evaluators and may include other positions, such as flight attendants, aircraft dispatchers, and other operations personnel. (e) Each certificate holder that obtains approval of an AQP under this SFAR shall comply with all of the requirements of that program. 2. Definitions. As used in this SFAR: Curriculum means a portion of an Advanced Qualification Program that covers one of three program areas: (1) indoctrination, (2) qualification, or (3) continuing qualification. A qualification or continuing qualification curriculum addresses the required training and qualification activities for a specific make, model, and series aircraft (or variant) and for a specific duty position. Evaluator means a person who has satisfactorily completed training and evaluation that qualifies that person to evaluate the performance of crewmembers, instructors, other evaluators, aircraft dispatchers, and other operations personnel. Facility means the physical environment required for training and qualification (e.g., buildings, classrooms). Training center means an organization certificated under part 142 of this chapter or an organization approved by the Administrator to operate under the terms of this SFAR to provide training as described in section 1(b) of SFAR 58. Variant means a specifically configured aircraft for which the FAA has identified training and qualification requirements that are significantly different from those applicable to other aircraft of the same make, model, and series. 3. Required Curriculums. Each AQP must have separate curriculums for indoctrination, qualification, and continuing qualification as specified in sections 4, 5, and 6 of this SFAR. 4. Indoctrination Curriculums. Each indoctrination curriculum must include the following: (a) For newly hired persons being trained under an AQP: Company policies and operating practices and general operational knowledge. (b) For newly hired flight crewmembers and aircraft dispatchers: General aeronautical knowledge. (c) For instructors: The fundamental principles of the teaching and learning process; methods and theories of instruction; and the knowledge necessary to use aircraft, flight training devices, flight simulators, and other training equipment in advanced qualification curriculums. (d) For evaluators: Evaluation requirements specified in each approved curriculum; methods of evaluating crewmembers and aircraft dispatchers and other operations personnel; and policies and practices used to conduct the kinds of evaluations particular to an advanced qualification curriculum (e.g., proficiency and online). 5. Qualification Curriculums. Each qualification curriculum must include the following: (a) The certificate holder's planned hours of training, evaluation, and supervised operating experience. [[Page 414]] (b) A list of and text describing the training, qualification, and certification activities, as applicable for specific positions subject to the AQP, as follows: (1) Crewmembers, aircraft dispatchers, and other operations personnel. Training, evaluation, and certification activities which are aircraft- and equipment-specific to qualify a person for a particular duty position on, or duties related to the operation of a specific make, model, and series aircraft (or variant); a list of and text describing the knowledge requirements, subject materials, job skills, and each maneuver and procedure to be trained and evaluated; the practical test requirements in addition to or in place of the requirements of parts 61, 63, and 65; and a list of and text describing supervised operating experience. (2) Instructors. Training and evaluation to qualify a person to impart instruction on how to operate, or on how to ensure the safe operation of a particular make, model, and series aircraft (or variant). (3) Evaluators. Training, evaluation, and certification activities that are aircraft and equipment specific to qualify a person to evaluate the performance of persons who operate or who ensure the safe operation of, a particular make, model, and series aircraft (or variant). 6. Continuing Qualification Curriculums. Continuing qualification curriculums must comply with the following requirements: (a) General. A continuing qualification curriculum must be based on-- (1) A continuing qualification cycle that ensures that during each cycle each person qualified under an AQP, including instructors and evaluators, will receive a balanced mix of training and evaluation on all events and subjects necessary to ensure that each person maintains the minimum proficiency level of knowledge, skills, and attitudes required for original qualification; and (2) If applicable, flight crewmember or aircraft dispatcher recency of experience requirements. (b) Continuing Qualification Cycle Content. Each continuing qualification cycle must include at least the following: (1) Evaluation period. An evaluation period during which each person qualified under an AQP must receive at least one training session and a proficiency evaluation at a training facility. The number and frequency of training sessions must be approved by the Administrator. A training session, including any proficiency evaluation completed at that session, that occurs any time during the two calendar months before the last date for completion of an evaluation period can be considered by the certificate holder to be completed in the last calendar month. (2) Training. Continuing qualification must include training in all events and major subjects required for original qualification, as follows: (i) For pilots in command, seconds in command, flight engineers, and instructors and evaluators: Ground training including a general review of knowledge and skills covered in qualification training, updated information on newly developed procedures, and safety information. (ii) For crewmembers, aircraft dispatchers, instructors, evaluators, and other operation personnel who conduct their duties in flight: Proficiency training in an aircraft, flight training device, or flight simulator on normal, abnormal, and emergency flight procedures and maneuvers. (iii) For instructors and evaluators who are limited to conducting their duties in flight simulators and flight training devices: Proficiency training in a flight training device and/or flight simulator regarding operation of this training equipment and in operational flight procedures and maneuvers (normal, abnormal, and emergency). (3) Evaluations. Continuing qualification must include evaluation in all events and major subjects required for original qualification, and online evaluations for pilots in command and other eligible flight crewmembers. Each person qualified under an AQP must successfully complete a proficiency evaluation and, if applicable, an online evaluation during each evaluation period. An individual's proficiency evaluation may be accomplished over several training sessions if a certificate holder provides more than one training session in an evaluation period. The following evaluation requirements apply: (i) Proficiency evaluations as follows: (A) For pilots in command, seconds in command, and flight engineers: A proficiency evaluation, portions of which may be conducted in an aircraft, flight simulator, or flight training device as approved in the certificate holder's curriculum which must be completed during each evaluation period. (B) For any other persons covered by an AQP a means to evaluate their proficiency in the performance of their duties in their assigned tasks in an operational setting. (ii) Online evaluations as follows: (A) For pilots in command: An online evaluation conducted in an aircraft during actual flight operations under part 121 or part 135 or during operationally (line) oriented flights, such as ferry flights or proving flights. An online evaluation in an aircraft must be completed in the calendar month that includes the midpoint of the evaluation period. An online evaluation that is satisfactorily completed in the calendar month before or the calendar month after the calendar month in which it becomes due is considered to have been completed during the calendar month it became due. However, in no case is an online evaluation under this [[Page 415]] paragraph required more often than once during an evaluation period. (B) During the online evaluations required under paragraph (b)(3)(ii)(A) of this section, each person performing duties as a pilot in command, second in command, or flight engineer for that flight, must be individually evaluated to determine whether he or she--(1) Remains adequately trained and currently proficient with respect to the particular aircraft, crew position, and type of operation in which he or she serves; and (2) Has sufficient knowledge and skills to operate effectively as part of a crew. (4) Recency of experience. For pilots in command and seconds in command, and, if the certificate holder elects, flight engineers and aircraft dispatchers, approved recency of experience requirements. (c) Duration periods. Initially the continuing qualification cycle approved for an AQP may not exceed 26 calendar months and the evaluation period may not exceed 13 calendar months. Thereafter, upon demonstration by a certificate holder that an extension is warranted, the Administrator may approve extensions of the continuing qualification cycle and the evaluation period in increments not exceeding 3 calendar months. However, a continuing qualification cycle may not exceed 39 calendar months and an evaluation period may not exceed 26 calendar months. (d) Requalification. Each continuing qualification curriculum must include a curriculum segment that covers the requirements for requalifying a crewmember, aircraft dispatcher, or other operations personnel who has not maintained continuing qualification. 7. Other Requirements. In addition to the requirements of sections 4, 5, and 6, each AQP qualification and continuing qualification curriculum must include the following requirements: (a) Approved Cockpit Resource Management (CRM) Training applicable to each position for which training is provided under an AQP. (b) Approved training on and evaluation of skills and proficiency of each person being trained under an AQP to use their cockpit resource management skills and their technical (piloting or other) skills in an actual or simulated operations scenario. For flight crewmembers this training and evaluation must be conducted in an approved flight training device or flight simulator. (c) Data collection procedures that will ensure that the certificate holder provides information from its crewmembers, instructors, and evaluators that will enable the FAA to determine whether the training and evaluations are working to accomplish the overall objectives of the curriculum. 8. Certification. A person enrolled in an AQP is eligible to receive a commercial or airline transport pilot, flight engineer, or aircraft dispatcher certificate or appropriate rating based on the successful completion of training and evaluation events accomplished under that program if the following requirements are met: (a) Training and evaluation of required knowledge and skills under the AQP must meet minimum certification and rating criteria established by the Administrator in parts 61, 63, or 65. The Administrator may accept substitutes for the practical test requirements of parts 61, 63, or 65, as applicable. (b) The applicant satisfactorily completes the appropriate qualification curriculum. (c) The applicant shows competence in required technical knowledge and skills (e.g., piloting) and cockpit resource management knowledge and skills in scenarios that test both types of knowledge and skills together. (d) The applicant is otherwise eligible under the applicable requirements of part 61, 63, or 65. 9. Training Devices and Simulators. (a) Qualification and approval of flight training devices and flight simulators. (1) Any training device or simulator that will be used in an AQP for one of the following purposes must be evaluated by the Administrator for assignment of a flight training device or flight simulator qualification level: (i) Required evaluation of individual or crew proficiency. (ii) Training activities that determine if an individual or crew is ready for a proficiency evaluation. (iii) Activities used to meet recency of experience requirements. (iv) Line Operational Simulations (LOS). (2) To be eligible to request evaluation for a qualification level of a flight training device or flight simulator an applicant must-- (i) Hold an operating certificate; or (ii) Be a training center that has applied for authorization to the Administrator or has been authorized by the Administrator to conduct training or qualification under an AQP. (3) Each flight training device or flight simulator to be used by a certificate holder or training center for any of the purposes set forth in paragraph (a)(1) of this section must-- (i) Be, or have been, evaluated against a set of criteria established by the Administrator for a particular qualification level of simulation; (ii) Be approved for its intended use in a specified AQP; and (iii) Be part of a flight simulator or flight training device continuing qualification program approved by the Administrator. (b) Approval of other Training Equipment. (1) Any training device that is intended to be used in an AQP for purposes other than those set forth in paragraph (a)(1) of this section [[Page 416]] must be approved by the Administrator for its intended use. (2) An applicant for approval of a training device under this paragraph must identify the device by its nomenclature and describe its intended use. (3) Each training device approved for use in an AQP must be part of a continuing program to provide for its serviceability and fitness to perform its intended function as approved by the Administrator. 10. Approval of Advanced Qualification Program. (a) Approval Process. Each applicant for approval of an AQP curriculum under this SFAR shall apply for approval of that curriculum. Application for approval is made to the certificate holder's FAA Flight Standards District Office. (b) Approval Criteria. An application for approval of an AQP curriculum will be approved if the program meets the following requirements: (1) It must be submitted in a form and manner acceptable to the Administrator. (2) It must meet all of the requirements of this SFAR. (3) It must indicate specifically the requirements of parts 61, 63, 65, 121 or 135, as applicable, that would be replaced by an AQP curriculum. If a requirement of parts 61, 63, 65, 121, or 135 is replaced by an AQP curriculum, the certificate holder must show how the AQP curriculum provides an equivalent level of safety for each requirement that is replaced. Each applicable requirement of parts 61, 63, 65, 121 or 135 that is not specifically addressed in an AQP curriculum continues to apply to the certificate holder. (c) Application and Transition. Each certificate holder that applies for one or more advanced qualification curriculums or for a revision to a previously approved curriculum must comply with Sec. 121.405 or Sec. 135.325, as applicable, and must include as part of its application a proposed transition plan (containing a calendar of events) for moving from its present approved training to the advanced qualification training. (d) Advanced Qualification Program Revisions or Rescissions of Approval. If after a certificate holder begins operations under an AQP, the Administrator finds that the certificate holder is not meeting the provisions of its approved AQP, the Administrator may require the certificate holder to make revisions in accordance with Sec. 121.405 or Sec. 135.325, as applicable, or to submit and obtain approval for a plan (containing a schedule of events) that the certificate holder must comply with and use to transition to an approved part 121 or part 135 training program, as appropriate. 11. Approval of Training, Qualification, or Evaluation by a Person who Provides Training by Arrangement. (a) A certificate holder under part 121 or part 135 may arrange to have AQP required training, qualification, or evaluation functions performed by another person (a training center) if the following requirements are met: (1) The training center's training and qualification curriculums, curriculum segments, or portions of curriculum segments must be provisionally approved by the Administrator. A training center may apply for provisional approval independently or in conjunction with a certificate holder's application for AQP approval. Application for provisional approval must be made to the FAA's Flight Standards District Office that has responsibility for the training center. (2) The specific use of provisionally approved curriculums, curriculum segments, or portions of curriculum segments in a certificate holder's AQP must be approved by the Administrator as set forth in section 10 of this SFAR. (b) An applicant for provisional approval of a curriculum, curriculum segment, or portion of a curriculum segment under this paragraph must show that the following requirements are met: (1) The applicant must have a curriculum for the qualification and continuing qualification of each instructor or evaluator employed by the applicant. (2) The applicant's facilities must be found by the Administrator to be adequate for any planned training, qualification, or evaluation for a part 121 or part 135 certificate holder. (3) Except for indoctrination curriculums, the curriculum, curriculum segment, or portion of a curriculum segment must identify the specific make, model, and series aircraft (or variant) and crewmember or other positions for which it is designed. (c) A certificate holder who wants approval to use a training center's provisionally approved curriculum, curriculum segment, or portion of a curriculum segment in its AQP, must show that the following requirements are met: (1) Each instructor or evaluator used by the training center must meet all of the qualification and continuing qualification requirements that apply to employees of the certificate holder that has arranged for the training, including knowledge of the certificate holder's operations. (2) Each provisionally approved curriculum, curriculum segment, or portion of a curriculum segment must be approved by the Administrator for use in the certificate holder's AQP. The Administrator will either provide approval or require modifications to ensure that each curriculum, curriculum segment, or portion of a curriculum segment is applicable to the certificate holder's AQP. (d) Approval for the training, qualification, or evaluation by a person who provides training by arrangement authorized by this [[Page 417]] section expires on August 3, 1998 unless that person meets the eligibility requirements specified under Sec. 121.402 or Sec. 135.324 of this chapter. After August 2, 1998 approval for the training, qualification, or evaluation, by a person who provides training by arrangement authorized by this section, shall be granted only to persons who meet the eligibility requirements specified under Sec. 121.402 or Sec. 135.234 of this chapter. 12. Recordkeeping Requirements. Each certificate holder and each training center holding AQP provisional approval shall show that it will establish and maintain records in sufficient detail to establish the training, qualification, and certification of each person qualified under an AQP in accordance with the training, qualification, and certification requirements of this SFAR. 13. Expiration. This Special Federal Aviation Regulation terminates on October 2, 2005, unless sooner terminated. [SFAR-58, 55 FR 40275, Oct. 2, 1990, as amended at 60 FR 51851, Oct. 3, 1995; SFAR 58-2, 61 FR 34560, July 2, 1996; Amdt. 121-280, 65 FR 60336, Oct. 10, 2000] Special Federal Aviation Regulation No. 71 Editorial Note: For the text of SFAR No. 71, see part 91 of this chapter. Special Federal Aviation Regulation No. 78 Editorial Note: For the text of SFAR No. 78, see part 91 of this chapter. Special Federal Aviation Regulation 80--Alternative Communications and Dispatching Procedures 1. Applicability. This Special Federal Aviation Regulation applies to each holder of an air carrier or operating certificate (hereafter, certificate holder) that meets one of the following eligibility requirements: a. The certificate holder conducts scheduled operations with airplanes having a passenger-seat configuration of 30 seats or fewer, excluding each crewmember seat, and a payload capacity of 7,500 pounds or less under part 121 of this chapter. b. The certificate holder conducts domestic operations in Alaska under part 121 of this chapter. 2. Alternative requirements. a. If an operator described in paragraph 1.a. of this SFAR is conducting a flight with an airplane described in 1.a. and if communications cannot be maintained over the entire route (which would be contrary to the requirements of Sec. 121.99 of this chapter), such an operator may continue to operate over such a route subject to approval by the Administrator. In granting such approval the Administrator considers the following: i. The operator has an established dispatch communication system. ii. Gaps in communication are not over the entire route, but only over portions of the route. iii. When communication gaps occur, they occur due to one or more of the following: A. Lack of infrastructure. B. Geographical considerations. C. Assigned operating altitude. iv. Procedures are established for the prompt re-establishment of communications. v. The operator has presented a plan or schedule for coming into compliance with the requirements in Sec. 121.99 of this chapter. b. A certificate holder who conducts domestic operations in Alaska may, notwithstanding the requirements of Sec. 121.99 of this chapter, use a communications system operated by the United States for those operations. c. An operator described in paragraph 1.a. of this SFAR who conducts operations in Alaska may share the aircraft dispatcher required by Sec. 121.395 with another operator described in paragraph 1.a. of this SFAR who conducts operations in Alaska if authorized to do so by the Administrator. Before granting such an authorization, the Administrator considers: i. The operators' joint plans for complying with the aircraft dispatcher training rules in subpart N of part 121 of this chapter and the aircraft dispatcher qualification and duty time limitation rules in subpart P of part 121 of this chapter. ii. The number of flights for which the aircraft dispatcher would be responsible. iii. Whether the responsibilities of the dispatcher would be beyond the capability of a single dispatcher. 3. Expiration. This Special Federal Aviation Regulation terminates on March 12, 2001, unless sooner terminated. [SFAR-80, 62 FR 13255, Mar. 19, 1997; 62 FR 15570, Apr. 1, 1997] Special Federal Aviation Regulation 92-5--Flightcrew Compartment Access and Door Designs 1. Applicability. This Special Federal Aviation Regulation (SFAR) applies to all operators that hold an air carrier certificate or operating certificate issued under 14 CFR part 119 and that conduct operations under this part 121 and to operators of U.S. registered transport category airplanes operated under 14 CFR part 129, except paragraph 5 of this SFAR does not apply to cargo operations and 14 CFR part 129 operations. It applies to the operators specified in this SFAR that modify airplanes to improve the flightcrew compartment door installations [[Page 418]] to restrict the unwanted entry of persons into the flightcrew compartment. This SFAR also applies to production certificate holders and applicants for airworthiness certificates for airplanes to be operated by operators specified in this SFAR, and producers of parts to be used in modifications of such airplanes. 2. Regulatory Relief. Contrary provisions of this part 21, and Sec. Sec. 121.313(h), 121.153(a)(2), 121.153(c), 121.379(b), 121.583(b)(1) and (2) and 14 CFR 129.13 notwithstanding: (a) An operator may operate airplanes modified to improve the flightcrew compartment door installations to restrict the unauthorized entry of persons into the flightcrew compartment without regard to the applicable airworthiness requirements and may modify those airplanes for that purpose, using technical data not previously approved by the Administrator, subject to the following conditions: (i) Not later than February 15, 2002, submit to the Director, Aircraft Certification Service, a detailed description of the changes to the airplane that have been accomplished before that date to enhance the intrusion resistance of the flightcrew compartment including identification of what major alterations have been done without previously approved data. (ii) If, upon reviewing the data submitted in paragraph 2(a)(i) of this SFAR, the Administrator determines that a door modification presents an unacceptable safety risk, the FAA may issue an order requiring changes to such modifications. (b) An applicant for an airworthiness certificate may obtain such a certificate for modified airplanes to be operated by operators described in this SFAR. (c) A holder of a production certificate may submit for airworthiness certification or approval, modified airplanes to be operated by operators described in this SFAR. (d) A person may produce parts for installation on airplanes in connection with modifications described in this SFAR, without FAA parts manufacturer approval (PMA). 3. Report of Modifications. Not later than April 22, 2002, all operators who are required to install flightdeck door modifications in accordance with 14 CFR 121.313(j) must submit a report to the Director, Aircraft Certification Service. The report must describe the modifications to be made and provide a schedule for the changes necessary to restore compliance with all applicable airworthiness requirements and to meet the requirements of 14 CFR 121.313(j). The schedule may not extend beyond the termination date of this SFAR. 4. Return to Service Documentation. Where operators have modified airplanes as authorized in this SFAR, the affected airplane must be returned to service with a note that it was done under the provisions of this SFAR. 5. Provision for Flightdeck Door Compartment Key. Contrary to provisions of Sec. 121.313(g), the following provision applies: A key for each door that separates a passenger compartment from an emergency exit must be identified to passengers in the briefing required by Sec. 121.571(a)(1)(ii). The key required for access to the emergency exit must be readily available for each crewmember. No key to the flightcrew compartment shall be available to any crewmember during flight, except for flight crewmembers, unless an internal flightdeck locking device such as a deadbolt or bar is installed, operative, and in use. 6. Door Modification Requirement. After March 1, 2002, for each airplane required under Sec. 121.313(f) to have a door between the passenger and pilot compartments, and for transport category all-cargo airplanes that have a door installed between the pilot compartment and any other occupied compartment on or after January 15, 2002, such door must be equipped with an internal locking device installed, operative, and in use. Such internal locking device has to be designed so that it can only be unlocked from inside the flightdeck. 7. Termination. For all-cargo transport category airplanes, this SFAR terminates on October 1, 2003. For passenger airplanes, this SFAR expires on April 9, 2003, except for airplanes meeting the criteria specified in paragraphs 7.a, b, and c, below. For airplanes meeting these criteria, this SFAR expires on July 31, 2003. a. Before midnight April 9, 2003, the operator must have installed a strengthened flightdeck door meeting the requirement of paragraph 7.b; b. Before midnight April 9, 2003, the FAA must have found that the door complies with 14 CFR 25.795(a)(1) and (2) in effect on January 15, 2002; and c. Before March 10, 2003, a formal application for certification approval of the door must have been submitted to the FAA. [Doc. FAA-2001-10770, 68 FR 17516, Apr. 9, 2003] Special Federal Aviation Regulation No. 93 Editorial Note: For the text of SFAR No. 93, see part 61 of this chapter. Special Federal Aviation Regulation No. 97 Editorial Note: For the text of SFAR No. 97, see part 91 of this chapter. [[Page 419]] This part prescribes rules governing-- (a) The domestic, flag, and supplemental operations of each person who holds or is required to hold an Air Carrier Certificate or Operating Certificate under part 119 of this chapter. (b) Each person employed or used by a certificate holder conducting operations under this part including maintenance, preventive maintenance, and alteration of aircraft. (c) Each person who applies for provisional approval of an Advanced Qualification Program curriculum, curriculum segment, or portion of a curriculum segment under SFAR No. 58 of 14 CFR part 121, and each person employed or used by an air carrier or commercial operator under this part to perform training, qualification, or evaluation functions under an Advanced Qualification Program under SFAR No. 58 of 14 CFR part 121. (d) Nonstop sightseeing flights conducted with airplanes having a passenger-seat configuration of 30 seats or fewer and a maximum payload capacity of 7,500 pounds or less that begin and end at the same airport, and are conducted within a 25 statute mile radius of that airport; however, except for operations subject to SFAR 50-2 of 14 CFR part 121, these operations, when conducted for compensation or hire, must comply only with Sec. Sec. 121.455 and 121.457, except that an operator who does not hold an air carrier certificate or an operating certificate is permitted to use a person who is otherwise authorized to perform aircraft maintenance or preventive maintenance duties and who is not subject to FAA-approved anti-drug and alcohol misuse prevention programs to perform-- (1) Aircraft maintenance or preventive maintenance on the operator's aircraft if the operator would otherwise be required to transport the aircraft more than 50 nautical miles further than the repair point closest to the operator's principal base of operations to obtain these services; or (2) Emergency repairs on the operator's aircraft if the aircraft cannot be safely operated to a location where an employee subject to FAA-approved programs can perform the repairs. (e) Each person who is on board an aircraft being operated under this part. (f) Each person who is an applicant for an Air Carrier Certificate or an Operating Certificate under part 119 of this chapter, when conducting proving tests. [Doc. No. 28154, 60 FR 65925, Dec. 20, 1995]