[Code of Federal Regulations] [Title 40, Volume 25] [Revised as of July 1, 2005] From the U.S. Government Printing Office via GPO Access [CITE: 40CFR260.11] [Page 17-20] TITLE 40--PROTECTION OF ENVIRONMENT CHAPTER I--ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PART 260_HAZARDOUS WASTE MANAGEMENT SYSTEM: GENERAL--Table of Contents Subpart B_Definitions Sec. 260.11 References. (a) When used in parts 260 through 270 of this chapter, the following publications are incorporated by reference: (1) ``ASTM Standard Test Methods for Flash Point of Liquids by Setaflash Closed Tester,'' ASTM Standard D-3278-78, available from American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103. (2) ``ASTM Standard Test Methods for Flash Point by Pensky-Martens Closed Tester,'' ASTM Standard D-93-79 or D-93-80. D-93-80 is available from American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103. (3) ``ASTM Standard Method for Analysis of Reformed Gas by Gas Chromatography,'' ASTM Standard D-1946-82, available from American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103. (4) ``ASTM Standard Test Method for Heat of Combustion of Hydrocarbon Fuels by Bomb Calorimeter (High-Precision Method),'' ASTM Standard D 2382-83, available from American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103. (5) ``ASTM Standard Practices for General Techniques of Ultraviolet- Visible Quantitative Analysis,'' ASTM Standard E 169-87 available from American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103. [[Page 18]] (6) ``ASTM Standard Practices for General Techniques of Infrared Quantitative Analysis,'' ASTM Standard E 168-88, available from American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103. (7) ``ASTM Standard Practice for Packed Column Gas Chromatography,'' ASTM Standard E 260-85, available from American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103. (8) ``ASTM Standard Test Method for Aromatics in Light Naphthas and Aviation Gasolines by Gas Chromatography,'' ASTM Standard D 2267-88, available from American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103. (9) ``APTI Course 415: Control of Gaseous Emissions,'' EPA Publication EPA-450/2-81-005, December 1981, available from National Technical Information Service, 5285 Port Royal Road, Springfield, VA 22161. (10) ``Flammable and Combustible Liquids Code'' (1977 or 1981), available from the National Fire Protection Association, 470 Atlantic Avenue, Boston, MA 02210. (11) ``Test Methods for Evaluating Solid Waste, Physical/Chemical Methods,'' EPA Publication SW-846 [Third Edition (November 1986), as amended by Updates I (dated July 1992), II (dated September 1994), IIA (dated August 1993), IIB (dated January 1995), III (dated December 1996) and IIIA (dated April 1998)]. The Third Edition of SW-846 and Updates I, II, IIA, IIB, and III (document number 955-001-00000-1) are available from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402, (202) 512-1800. Update IIIA is available through EPA's Methods Information Communication Exchange (MICE) Service. MICE can be contacted by phone at (703) 821-4690. Update IIIA can also be obtained by contacting the U.S. Environmental Protection Agency, Office of Solid Waste (5307W), OSW Methods Team, 1200 Pennsylvania Ave., NW., Washington, DC 20460. Copies of the Third Edition and all of its updates are also available from the National Technical Information Service (NTIS), 5285 Port Royal Road, Springfield, VA 22161, (703) 605-6000 or (800) 553-6847. Copies may be inspected at the Library, U.S. Environmental Protection Agency, 401 M St., SW., Washington, DC 20460; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741- 6030, or go to: http://www.archives.gov/federal--register/code--of-- federal--regulations/ibr--locations.html. (12) ``Screening Procedures for Estimating the Air Quality Impact of Stationary Sources, Revised'', October 1992, EPA Publication No. EPA- 450/R-92-019, Environmental Protection Agency, Research Triangle Park, NC. (13) ``ASTM Standard Test Methods for Preparing Refuse-Derived Fuel (RDF) Samples for Analyses of Metals,'' ASTM Standard E926-88, Test Method C--Bomb, Acid Digestion Method, available from American Society for Testing Materials, 1916 Race Street, Philadelphia, PA 19103. (14) ``API Publication 2517, Third Edition'', February 1989, ``Evaporative Loss from External Floating-Roof Tanks,'' available from the American Petroleum Institute, 1220 L Street, Northwest, Washington, DC 20005. (15) ``ASTM Standard Test Method for Vapor Pressure--Temperature Relationship and Initial Decomposition Temperature of Liquids by Isoteniscope,'' ASTM Standard D 2879-92, available from American Society for Testing and Materials (ASTM), 1916 Race Street, Philadelphia, PA 19103. (16) Method 1664, Revision A, n-Hexane Extractable Material (HEM; Oil and Grease) and Silica Gel Treated n-Hexane Extractable Material (SGT-HEM; Non-polar Material) by Extraction and Gravimetry. Available at NTIS, PB99-121949, U.S. Department of Commerce, 5285 Port Royal, Springfield, Virginia 22161. (b) The references listed in paragraph (a) of this section are also available for inspection at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/ federal--register/code--of--federal--regulations/ibr--locations.html. These incorporations by reference were approved by the Director of the Federal Register. These materials are incorporated as they exist on the date of approval and a notice of any change in these materials will be published in the Federal Register. [46 FR 35247, July 7, 1981, as amended at 50 FR 18374, Apr. 30, 1985; 52 FR 8073, Mar. 16, 1987; 52 FR 41295, Oct. 27, 1987; 54 FR 40266, Sept. 29, 1989; 55 FR 8949, Mar. 9, 1990; 55 FR 25493, June 21, 1990; 56 FR 7206, Feb. 21, 1991; 58 FR 38883, July 20, 1993; 58 FR 46049, Aug. 31, 1993; 59 FR 468, Jan. 4, 1994; 59 FR 28484, June 2, 1994; 59 FR 62926, Dec. 6, 1994; 60 FR 17004, Apr. 4, 1995; 62 FR 32462, June 13, 1997; 64 FR 26327, May 11, 1999; 66 FR 34376, June 28, 2001; 69 FR 19903, Apr. 9, 2004] Effective Date Note: At 70 FR 34560, June 14, 2005, Sec. 260.11 was revised, effective July 14, 2005. For the convenience of the user, the revised text is set forth as follows: Sec. 260.11 References. (a) When used in parts 260 through 270 of this chapter, the following publications are incorporated by reference. These [[Page 19]] incorporations by reference were approved by the Director of the Federal Register pursuant to 5 U.S.C. 552(a) and 1 CFR part 51. These materials are incorporated as they exist on the date of approval and a notice of any change in these materials will be published in the Federal Register. Copies may be inspected at the Library, U.S. Environmental Protection Agency, 1200 Pennsylvania Ave., NW. (3403T), Washington, DC 20460, libraryhq@epa.gov; or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/ federal--register/code--of--federal--regulations/ibr--locations.html. (b) The following materials are available for purchase from the American Society for Testing and Materials, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959. (1) ASTM D-93-79 or D-93-80, ``Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester,'' IBR approved for Sec. 261.21. (2) ASTM D-1946-82, ``Standard Method for Analysis of Reformed Gas by Gas Chromatography,'' IBR approved for Sec. Sec. 264.1033, 265.1033. (3) ASTM D 2267-88, ``Standard Test Method for Aromatics in Light Naphthas and Aviation Gasolines by Gas Chromatography,'' IBR approved for Sec. 264.1063. (4) ASTM D 2382-83, ``Standard Test Method for Heat of Combustion of Hydrocarbon Fuels by Bomb Calorimeter (High-Precision Method),'' IBR approved for Sec. Sec. 264.1033, 265.1033. (5) ASTM D 2879-92, ``Standard Test Method for Vapor Pressure-- Temperature Relationship and Initial Decomposition Temperature of Liquids by Isoteniscope,'' IBR approved for Sec. 265.1084. (6) ASTM D-3278-78, ``Standard Test Methods for Flash Point for Liquids by Setaflash Closed Tester,'' IBR approved for Sec. 261.21(a). (7) ASTM E 168-88, ``Standard Practices for General Techniques of Infrared Quantitative Analysis,'' IBR approved for Sec. 264.1063. (8) ASTM E 169-87, ``Standard Practices for General Techniques of Ultraviolet-Visible Quantitative Analysis,'' IBR approved for Sec. 264.1063. (9) ASTM E 260-85, ``Standard Practice for Packed Column Gas Chromatography,'' IBR approved for Sec. 264.1063. (10) ASTM E 926-88, ``Standard Test Methods for Preparing Refuse- Derived Fuel (RDF) Samples for Analyses of Metals,'' Test Method C-- Bomb, Acid Digestion Method. (c) The following materials are available for purchase from the National Technical Information Service, 5285 Port Royal Road, Springfield, VA 22161; or for purchase from the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402, (202) 512-1800. (1) ``APTI Course 415: Control of Gaseous Emissions,'' EPA Publication EPA-450/2-81-005, December 1981, IBR approved for Sec. Sec. 264.1035, 265.1035, 270.24, 270.25. (2) Method 1664, Revision A, n-Hexane Extractable Material (HEM; Oil and Grease) and Silica Gel Treated n-Hexane Extractable Material (SGT- HEM; Non-polar Material) by Extraction and Gravimetry, PB99-121949, IBR approved for part 261, appendix IX. (3) The following methods as published in the test methods compendium known as ``Test Methods for Evaluating Solid Waste, Physical/ Chemical Methods,'' EPA Publication SW-846, Third Edition. A suffix of ``A'' in the method number indicates revision one (the method has been revised once). A suffix of ``B'' in the method number indicates revision two (the method has been revised twice). A suffix of ``C'' in the method number indicates revision three (the method has been revised three times). A suffix of ``D'' in the method number indicates revision four (the method has been revised four times). (i) Method 0010, dated September 1986 and in the Basic Manual, IBR approved for part 261, appendix IX. (ii) Method 0020, dated September 1986 and in the Basic Manual, IBR approved for part 261, appendix IX. (iii) Method 0030, dated September 1986 and in the Basic Manual, IBR approved for part 261, appendix IX. (iv) Method 1320, dated September 1986 and in the Basic Manual, IBR approved for part 261, appendix IX. (v) Method 1311, dated September 1992 and in Update I, IBR approved for part 261, appendix IX, and Sec. Sec. 261.24, 268.7, 268.40. (vi) Method 1330A, dated September 1992 and in Update I, IBR approved for part 261, appendix IX. (vii) Method 1312 dated September 1994 and in Update II, IBR approved for part 261, appendix IX. (viii) Method 0011, dated December 1996 and in Update III, IBR approved for part 261, appendix IX, and part 266, appendix IX. (ix) Method 0023A, dated December 1996 and in Update III, IBR approved for part 261, appendix IX, part 266, appendix IX, and Sec. 266.104. (x) Method 0031, dated December 1996 and in Update III, IBR approved for part 261, appendix IX. (xi) Method 0040, dated December 1996 and in Update III, IBR approved for part 261, appendix IX. (xii) Method 0050, dated December 1996 and in Update III, IBR approved for part 261, appendix IX, part 266, appendix IX, and Sec. 266.107. (xiii) Method 0051, dated December 1996 and in Update III, IBR approved for part 261, appendix IX, part 266, appendix IX, and Sec. 266.107. [[Page 20]] (xiv) Method 0060, dated December 1996 and in Update III, IBR approved for part 261, appendix IX, Sec. 266.106, and part 266, appendix IX. (xv) Method 0061, dated December 1996 and in Update III, IBR approved for part 261, appendix IX, Sec. 266.106, and part 266, appendix IX. (xvi) Method 9071B, dated April 1998 and in Update IIIA, IBR approved for part 261, appendix IX. (xvii) Method 1010A, dated November 2004 and in Update IIIB, IBR approved for part 261, appendix IX. (xviii) Method 1020B, dated November 2004 and in Update IIIB, IBR approved for part 261, appendix IX. (xix) Method 1110A, dated November 2004 and in Update IIIB, IBR approved for Sec. 261.22 and part 261, appendix IX. (xx) Method 1310B, dated November 2004 and in Update IIIB, IBR approved for part 261, appendix IX. (xxi) Method 9010C, dated November 2004 and in Update IIIB, IBR approved for part 261, appendix IX and Sec. Sec. 268.40, 268.44, 268.48. (xxii) Method 9012B, dated November 2004 and in Update IIIB, IBR approved for part 261, appendix IX and Sec. Sec. 268.40, 268.44, 268.48. (xxiii) Method 9040C, dated November 2004 and in Update IIIB, IBR approved for part 261, appendix IX and Sec. 261.22. (xxiv) Method 9045D, dated November 2004 and in Update IIIB, IBR approved for part 261, appendix IX. (xxv) Method 9060A, dated November 2004 and in Update IIIB, IBR approved for part 261, appendix IX, and Sec. Sec. 264.1034, 264.1063, 265.1034, 265.1063. (xxvi) Method 9070A, dated November 2004 and in Update IIIB, IBR approved for part 261, appendix IX. (xxvii) Method 9095B, dated November 2004 and in Update IIIB, IBR approved, part 261, appendix IX, and Sec. Sec. 264.190, 264.314, 265.190, 265.314, 265.1081, 268.32. (d) The following materials are available for purchase from the National Fire Protection Association, 1 Batterymarch Park, P.O. Box 9101, Quincy, MA 02269-9101. (1) ``Flammable and Combustible Liquids Code'' (1977 or 1981), IBR approved for Sec. Sec. 264.198, 265.198. (2) [Reserved] (e) The following materials are available for purchase from the American Petroleum Institute, 1220 L Street, Northwest, Washington, DC 20005. (1) API Publication 2517, Third Edition, February 1989, ``Evaporative Loss from External Floating-Roof Tanks,'' IBR approved for Sec. 265.1084. (2) [Reserved] (f) The following materials are available for purchase from the Environmental Protection Agency, Research Triangle Park, NC. (1) ``Screening Procedures for Estimating the Air Quality Impact of Stationary Sources, Revised'', October 1992, EPA Publication No. EPA- 450/R-92-019, IBR approved for part 266, appendix IX. (2) [Reserved] (g) The following materials are available for purchase from the Organisation for Economic Co-operation and Development, Environment Direcorate, 2 rue Andre Pascal, 75775 Paris Cedex 16, France. (1) OECD Green List of Wastes (revised May 1994), Amber List of Wastes and Red List of Wastes (both revised May 1993) as set forth in Appendix 3, Appendix 4 and Appendix 5, respectively, to the OECD Council Decision C(92)39/FINAL (Concerning the Control of Transfrontier Movements of Wastes Destined for Recovery Operations), IBR approved for 262.89 of this chapter. (2) [Reserved]