[Code of Federal Regulations]
[Title 40, Volume 6]
[Revised as of July 1, 2005]
From the U.S. Government Printing Office via GPO Access
[CITE: 40CFR60.17]
[Page 73-78]
TITLE 40--PROTECTION OF ENVIRONMENT
CHAPTER I--ENVIRONMENTAL PROTECTION AGENCY (CONTINUED)
PART 60_STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES--Table of
Contents
Subpart A_General Provisions
Sec. 60.17 Incorporations by reference.
The materials listed below are incorporated by reference in the
corresponding sections noted. These incorporations by reference were
approved by the Director of the Federal Register on the date listed.
These materials are incorporated as they exist on the date of the
approval, and a notice of any change in these materials will be
published in the Federal Register. The materials are available for
purchase at the corresponding address noted below, and all are available
for inspection at the Library (MD-35), U.S. EPA, Research Triangle Park,
NC or at the National Archives and Records Administration (NARA). For
information on the availability of this material at NARA, call 202-741-
6030, or go to: http://www.archives.gov/federal--register/code--of--
federal--regulations/ibr--locations.html.
(a) The following materials are available for purchase from at least
one of the following addresses: American Society for Testing and
Materials (ASTM), 100 Barr Harbor Drive, Post Office Box C700, West
Conshohocken, PA 19428-2959; or ProQuest, 300 North Zeeb Road, Ann
Arbor, MI 48106.
(1) ASTM A99-76, 82 (Reapproved 1987), Standard Specification for
Ferromanganese, incorporation by reference (IBR) approved January 27,
1983 for Sec. 60.261.
(2) ASTM A100-69, 74, 93, Standard Specification for Ferrosilicon,
IBR approved January 27, 1983 for Sec. 60.261.
(3) ASTM A101-73, 93, Standard Specification for Ferrochromium, IBR
approved January 27, 1983 for Sec. 60.261.
(4) ASTM A482-76, 93, Standard Specification for Ferrochromesilicon,
IBR approved January 27, 1983 for Sec. 60.261.
(5) ASTM A483-64, 74 (Reapproved 1988), Standard Specification for
Silicomanganese, IBR approved January 27, 1983 for Sec. 60.261.
[[Page 74]]
(6) ASTM A495-76, 94, Standard Specification for Calcium-Silicon and
Calcium Manganese-Silicon, IBR approved January 27, 1983 for Sec.
60.261.
(7) ASTM D86-78, 82, 90, 93, 95, 96, Distillation of Petroleum
Products, IBR approved for Sec. Sec. 60.562-2(d), 60.593(d), and
60.633(h).
(8) ASTM D129-64, 78, 95, 00, Standard Test Method for Sulfur in
Petroleum Products (General Bomb Method), IBR approved for appendix A:
Method 19, 12.5.2.2.3; Sec. Sec. 60.106(j)(2) and 60.335(b)(10)(i).
(9) ASTM D240-76, 92, Standard Test Method for Heat of Combustion of
Liquid Hydrocarbon Fuels by Bomb Calorimeter, IBR approved January 27,
1983 for Sec. Sec. 60.46(c), 60.296(b), and Appendix A: Method 19,
Section 12.5.2.2.3.
(10) ASTM D270-65, 75, Standard Method of Sampling Petroleum and
Petroleum Products, IBR approved January 27, 1983 for Appendix A: Method
19, Section 12.5.2.2.1.
(11) ASTM D323-82, 94, Test Method for Vapor Pressure of Petroleum
Products (Reid Method), IBR approved April 8, 1987 for Sec. Sec.
60.111(l), 60.111a(g), 60.111b(g), and 60.116b(f)(2)(ii).
(12) ASTM D388-77, 90, 91, 95, 98a, Standard Specification for
Classification of Coals by Rank, IBR approved for Sec. Sec. 60.41(f),
60.45(f)(4)(i), 60.45(f)(4)(ii), 60.45(f)(4)(vi), 60.41a, 60.41b, and
60.251(b) and (c).
(13) ASTM D396-78, 89, 90, 92, 96, 98, Standard Specification for
Fuel Oils, IBR approved for Sec. Sec. 60.41b, 60.41c, 60.111(b), and
60.111a(b).
(14) ASTM D975-78, 96, 98a, Standard Specification for Diesel Fuel
Oils, IBR approved January 27, 1983 for Sec. Sec. 60.111(b) and
60.111a(b).
(15) ASTM D1072-80, 90 (Reapproved 1994), Standard Test Method for
Total Sulfur in Fuel Gases, IBR approved for Sec. 60.335(b)(10)(ii).
(16) ASTM D1137-53, 75, Standard Method for Analysis of Natural
Gases and Related Types of Gaseous Mixtures by the Mass Spectrometer,
IBR approved January 27, 1983 for Sec. 60.45(f)(5)(i).
(17) ASTM D1193-77, 91, Standard Specification for Reagent Water,
IBR approved for Appendix A: Method 5, Section 7.1.3; Method 5E, Section
7.2.1; Method 5F, Section 7.2.1; Method 6, Section 7.1.1; Method 7,
Section 7.1.1; Method 7C, Section 7.1.1; Method 7D, Section 7.1.1;
Method 10A, Section 7.1.1; Method 11, Section 7.1.3; Method 12, Section
7.1.3; Method 13A, Section 7.1.2; Method 26, Section 7.1.2; Method 26A,
Section 7.1.2; and Method 29, Section 7.2.2.
(18) ASTM D1266-87, 91, 98, Standard Test Method for Sulfur in
Petroleum Products (Lamp Method), IBR approved for Sec. Sec.
60.106(j)(2) and 60.335(b)(10)(i).
(19) ASTM D1475-60 (Reapproved 1980), 90, Standard Test Method for
Density of Paint, Varnish Lacquer, and Related Products, IBR approved
January 27, 1983 for Sec. 60.435(d)(1), Appendix A: Method 24, Section
6.1; and Method 24A, Sections 6.5 and 7.1.
(20) ASTM D1552-83, 95, 01, Standard Test Method for Sulfur in
Petroleum Products (High-Temperature Method), IBR approved for appendix
A: Method 19, Section 12.5.2.2.3; Sec. Sec. 60.106(j)(2) and
60.335(b)(10)(i).
(21) ASTM D1826-77, 94, Standard Test Method for Calorific Value of
Gases in Natural Gas Range by Continuous Recording Calorimeter, IBR
approved January 27, 1983 for Sec. Sec. 60.45(f)(5)(ii), 60.46(c)(2),
60.296(b)(3), and Appendix A: Method 19, Section 12.3.2.4.
(22) ASTM D1835-87, 91, 97, Standard Specification for Liquefied
Petroleum (LP) Gases, approved for Sec. Sec. 60.41b and 60.41c.
(23) ASTM D1945-64, 76, 91, 96, Standard Method for Analysis of
Natural Gas by Gas Chromatography, IBR approved January 27, 1983 for
Sec. 60.45(f)(5)(i).
(24) ASTM D1946-77, 90 (Reapproved 1994), Standard Method for
Analysis of Reformed Gas by Gas Chromatography, IBR approved for
Sec. Sec. 60.45(f)(5)(i), 60.18(f)(3), 60.614(e)(2)(ii), 60.614(e)(4),
60.664(e)(2)(ii), 60.664(e)(4), 60.564(f)(1), 60.704(d)(2)(ii), and
60.704(d)(4).
(25) ASTM D2013-72, 86, Standard Method of Preparing Coal Samples
for Analysis, IBR approved January 27, 1983, for Appendix A: Method 19,
Section 12.5.2.1.3.
(26) ASTM D2015-77 (Reapproved 1978), 96, Standard Test Method for
Gross Calorific Value of Solid Fuel by the Adiabatic Bomb Calorimeter,
IBR approved January 27, 1983 for Sec. 60.45(f)(5)(ii), 60.46(c)(2),
and Appendix A: Method 19, Section 12.5.2.1.3.
[[Page 75]]
(27) ASTM D2016-74, 83, Standard Test Methods for Moisture Content
of Wood, IBR approved for Appendix A: Method 28, Section 16.1.1.
(28) ASTM D2234-76, 96, 97b, 98, Standard Methods for Collection of
a Gross Sample of Coal, IBR approved January 27, 1983 for Appendix A:
Method 19, Section 12.5.2.1.1.
(29) ASTM D2369-81, 87, 90, 92, 93, 95, Standard Test Method for
Volatile Content of Coatings, IBR approved January 27, 1983 for Appendix
A: Method 24, Section 6.2.
(30) ASTM D2382-76, 88, Heat of Combustion of Hydrocarbon Fuels by
Bomb Calorimeter (High-Precision Method), IBR approved for Sec. Sec.
60.18(f)(3), 60.485(g)(6), 60.614(e)(4), 60.664(e)(4), 60.564(f)(3), and
60.704(d)(4).
(31) ASTM D2504-67, 77, 88 (Reapproved 1993), Noncondensable Gases
in C3 and Lighter Hydrocarbon Products by Gas Chromatography,
IBR approved for Sec. 60.485(g)(5).
(32) ASTM D2584-68 (Reapproved 1985), 94, Standard Test Method for
Ignition Loss of Cured Reinforced Resins, IBR approved February 25, 1985
for Sec. 60.685(c)(3)(i).
(33) ASTM D2622-87, 94, 98, Standard Test Method for Sulfur in
Petroleum Products by Wavelength Dispersive X-Ray Fluorescence
Spectrometry,'' IBR approved for Sec. Sec. 60.106(j)(2) and
60.335(b)(10)(i).
(34) ASTM D2879-83, 96, 97, Test Method for Vapor Pressure-
Temperature Relationship and Initial Decomposition Temperature of
Liquids by Isoteniscope, IBR approved April 8, 1987 for Sec. Sec.
60.485(e)(1), 60.111b(f)(3), 60.116b(e)(3)(ii), and 60.116b(f)(2)(i).
(35) ASTM D2880-78, 96, Standard Specification for Gas Turbine Fuel
Oils, IBR approved January 27, 1983 for Sec. Sec. 60.111(b),
60.111a(b), and 60.335(d).
(36) ASTM D2908-74, 91, Standard Practice for Measuring Volatile
Organic Matter in Water by Aqueous-Injection Gas Chromatography, IBR
approved for Sec. 60.564(j).
(37) ASTM D2986-71, 78, 95a, Standard Method for Evaluation of Air,
Assay Media by the Monodisperse DOP (Dioctyl Phthalate) Smoke Test, IBR
approved January 27, 1983 for Appendix A: Method 5, Section 7.1.1;
Method 12, Section 7.1.1; and Method 13A, Section 7.1.1.2.
(38) [Reserved]
(39) ASTM D3173-73, 87, Standard Test Method for Moisture in the
Analysis Sample of Coal and Coke, IBR approved January 27, 1983 for
Appendix A: Method 19, Section 12.5.2.1.3.
(40) ASTM D3176-74, 89, Standard Method for Ultimate Analysis of
Coal and Coke, IBR approved January 27, 1983 for Sec. 60.45(f)(5)(i)
and Appendix A: Method 19, Section 12.3.2.3.
(41) ASTM D3177-75, 89, Standard Test Method for Total Sulfur in the
Analysis Sample of Coal and Coke, IBR approved January 27, 1983 for
Appendix A: Method 19, Section 12.5.2.1.3.
(42) ASTM D3178-73 (Reapproved 1979), 89, Standard Test Methods for
Carbon and Hydrogen in the Analysis Sample of Coal and Coke, IBR
approved January 27, 1983 for Sec. 60.45(f)(5)(i).
(43) ASTM D3246-81, 92, 96, Standard Test Method for Sulfur in
Petroleum Gas by Oxidative Microcoulometry, IBR approved for Sec.
60.335(b)(10)(ii).
(44) ASTM D3270-73T, 80, 91, 95, Standard Test Methods for Analysis
for Fluoride Content of the Atmosphere and Plant Tissues (Semiautomated
Method), IBR approved for Appendix A: Method 13A, Section 16.1.
(45) ASTM D3286-85, 96, Standard Test Method for Gross Calorific
Value of Coal and Coke by the Isoperibol Bomb Calorimeter, IBR approved
for Appendix A: Method 19, Section 12.5.2.1.3.
(46) ASTM D3370-76, 95a, Standard Practices for Sampling Water, IBR
approved for Sec. 60.564(j).
(47) ASTM D3792-79, 91, Standard Test Method for Water Content of
Water-Reducible Paints by Direct Injection into a Gas Chromatograph, IBR
approved January 27, 1983 for Appendix A: Method 24, Section 6.3.
(48) ASTM D4017-81, 90, 96a, Standard Test Method for Water in
Paints and Paint Materials by the Karl Fischer Titration Method, IBR
approved January 27, 1983 for Appendix A: Method 24, Section 6.4.
(49) ASTM D4057-81, 95, Standard Practice for Manual Sampling of
Petroleum and Petroleum Products, IBR approved for Appendix A: Method
19, Section 12.5.2.2.3.
[[Page 76]]
(50) ASTM D4084-82, 94, Standard Test Method for Analysis of
Hydrogen Sulfide in Gaseous Fuels (Lead Acetate Reaction Rate Method),
IBR approved for Sec. 60.334(h)(1).
(51) ASTM D4177-95, Standard Practice for Automatic Sampling of
Petroleum and Petroleum Products, IBR approved for Appendix A: Method
19, 12.5.2.2.1.
(52) ASTM D4239-85, 94, 97, Standard Test Methods for Sulfur in the
Analysis Sample of Coal and Coke Using High Temperature Tube Furnace
Combustion Methods, IBR approved for Appendix A: Method 19, Section
12.5.2.1.3.
(53) ASTM D4442-84, 92, Standard Test Methods for Direct Moisture
Content Measurement in Wood and Wood-base Materials, IBR approved for
Appendix A: Method 28, Section 16.1.1.
(54) ASTM D4444-92, Standard Test Methods for Use and Calibration of
Hand-Held Moisture Meters, IBR approved for Appendix A: Method 28,
Section 16.1.1.
(55) ASTM D4457-85 (Reapproved 1991), Test Method for Determination
of Dichloromethane and 1, 1, 1-Trichloroethane in Paints and Coatings by
Direct Injection into a Gas Chromatograph, IBR approved for Appendix A:
Method 24, Section 6.5.
(56) ASTM D4809-95, Standard Test Method for Heat of Combustion of
Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method), IBR
approved for Sec. Sec. 60.18(f)(3), 60.485(g)(6), 60.564(f)(3),
60.614(d)(4), 60.664(e)(4), and 60.704(d)(4).
(57) ASTM D5403-93, Standard Test Methods for Volatile Content of
Radiation Curable Materials. IBR approved September 11, 1995 for
Appendix A: Method 24, Section 6.6.
(58) ASTM D5865-98, Standard Test Method for Gross Calorific Value
of Coal and Coke. IBR approved for Sec. 60.45(f)(5)(ii), 60.46(c)(2),
and Appendix A: Method 19, Section 12.5.2.1.3.
(59) ASTM E168-67, 77, 92, General Techniques of Infrared
Quantitative Analysis, IBR approved for Sec. Sec. 60.593(b)(2) and
60.632(f).
(60) ASTM E169-63, 77, 93, General Techniques of Ultraviolet
Quantitative Analysis, IBR approved for Sec. Sec. 60.593(b)(2) and
60.632(f).
(61) ASTM E260-73, 91, 96, General Gas Chromatography Procedures,
IBR approved for Sec. Sec. 60.593(b)(2) and 60.632(f).
(62)-(63) [Reserved]
(64) ASTM D 6216-98 Standard Practice for Opacity Monitor
Manufacturers to Certify Conformance with Design and Performance
Specifications, IBR approved February 6, 2001 for appendix B, PS-1.
(65) ASTM D2597-94 (Reapproved 1999), Standard Test Method for
Analysis of Demethanized Hydrocarbon Liquid Mixtures Containing Nitrogen
and Carbon Dioxide by Gas Chromatography, IBR approved for Sec.
60.335(b)(9)(i).
(66) ASTM D4294-02, Standard Test Method for Sulfur in Petroleum and
Petroleum Products by Energy-Dispersive X-Ray Fluorescence Spectrometry,
IBR approved for Sec. 60.335(b)(10)(i).
(67) ASTM D4468-85 (Reapproved 2000), Standard Test Method for Total
Sulfur in Gaseous Fuels by Hydrogenolysis and Rateometric Colorimetry,
IBR approved for Sec. 60.335(b)(10)(ii).
(68) ASTM D4629-02, Standard Test Method for Trace Nitrogen in
Liquid Petroleum Hydrocarbons by Syringe/Inlet Oxidative Combustion and
Chemiluminescence Detection, IBR approved for Sec. 60.335(b)(9)(i).
(69) ASTM D5453-00, Standard Test Method for Determination of Total
Sulfur in Light Hydrocarbons, Motor Fuels and Oils by Ultraviolet
Fluorescence, IBR approved for Sec. 60.335(b)(10)(i).
(70) ASTM D5504-01, Standard Test Method for Determination of Sulfur
Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and
Chemiluminescence, IBR approved for Sec. 60.334(h)(1).
(71) ASTM D5762-02, Standard Test Method for Nitrogen in Petroleum
and Petroleum Products by Boat-Inlet Chemiluminescence, IBR approved for
Sec. 60.335(b)(9)(i).
(72) ASTM D6228-98, Standard Test Method for Determination of Sulfur
Compounds in Natural Gas and Gaseous Fuels by Gas Chromatography and
Flame Photometric Detection, IBR approved for Sec. 60.334(h)(1).
(73) ASTM D6366-99, Standard Test Method for Total Trace Nitrogen
and
[[Page 77]]
Its Derivatives in Liquid Aromatic Hydrocarbons by Oxidative Combustion
and Electrochemical Detection, IBR approved for Sec. 60.335(b)(9)(i).
(74) ASTM D6522-00, Standard Test Method for Determination of
Nitrogen Oxides, Carbon Monoxide, and Oxygen Concentrations in Emissions
from Natural Gas-Fired Reciprocating Engines, Combustion Turbines,
Boilers, and Process Heaters Using Portable Analyzers, IBR approved for
Sec. 60.335(a).
(75) ASTM D6667-01, Standard Test Method for Determination of Total
Volatile Sulfur in Gaseous Hydrocarbons and Liquefied Petroleum Gases by
Ultraviolet Fluorescence, IBR approved for Sec. 60.335(b)(10)(ii).
(b) The following material is available for purchase from the
Association of Official Analytical Chemists, 1111 North 19th Street,
Suite 210, Arlington, VA 22209.
(1) AOAC Method 9, Official Methods of Analysis of the Association
of Official Analytical Chemists, 11th edition, 1970, pp. 11-12, IBR
approved January 27, 1983 for Sec. Sec. 60.204(b)(3), 60.214(b)(3),
60.224(b)(3), 60.234(b)(3).
(c) The following material is available for purchase from the
American Petroleum Institute, 1220 L Street NW., Washington, DC 20005.
(1) API Publication 2517, Evaporation Loss from External Floating
Roof Tanks, Second Edition, February 1980, IBR approved January 27,
1983, for Sec. Sec. 60.111(i), 60.111a(f), 60.111a(f)(1) and
60.116b(e)(2)(i).
(d) The following material is available for purchase from the
Technical Association of the Pulp and Paper Industry (TAPPI), Dunwoody
Park, Atlanta, GA 30341.
(1) TAPPI Method T624 os-68, IBR approved January 27, 1983 for Sec.
60.285(d)(3).
(e) The following material is available for purchase from the Water
Pollution Control Federation (WPCF), 2626 Pennsylvania Avenue NW.,
Washington, DC 20037.
(1) Method 209A, Total Residue Dried at 103-105 [deg]C, in Standard
Methods for the Examination of Water and Wastewater, 15th Edition, 1980,
IBR approved February 25, 1985 for Sec. 60.683(b).
(f) The following material is available for purchase from the
following address: Underwriter's Laboratories, Inc. (UL), 333 Pfingsten
Road, Northbrook, IL 60062.
(1) UL 103, Sixth Edition revised as of September 3, 1986, Standard
for Chimneys, Factory-built, Residential Type and Building Heating
Appliance.
(g) The following material is available for purchase from the
following address: West Coast Lumber Inspection Bureau, 6980 SW. Barnes
Road, Portland, OR 97223.
(1) West Coast Lumber Standard Grading Rules No. 16, pages 5-21 and
90 and 91, September 3, 1970, revised 1984.
(h) The following material is available for purchase from the
American Society of Mechanical Engineers (ASME), 345 East 47th Street,
New York, NY 10017.
(1) ASME QRO-1-1994, Standard for the Qualification and
Certification of Resource Recovery Facility Operators, IBR approved for
Sec. Sec. 60.56a, 60.54b(a), 60.54b(b), 60.1185(a), 60.1185(c)(2),
60.1675(a), and 60.1675(c)(2).
(2) ASME PTC 4.1-1964 (Reaffirmed 1991), Power Test Codes: Test Code
for Steam Generating Units (with 1968 and 1969 Addenda), IBR approved
for Sec. Sec. 60.46b, 60.58a(h)(6)(ii), 60.58b(i)(6)(ii), 60.1320(a)(3)
and 60.1810(a)(3).
(3) ASME Interim Supplement 19.5 on Instruments and Apparatus:
Application, Part II of Fluid Meters, 6th Edition (1971), IBR approved
for Sec. Sec. 60.58a(h)(6)(ii), 60.58b(i)(6)(ii), 60.1320(a)4), and
60.1810(a)(4).
(i) Test Methods for Evaluating Solid Waste, Physical/Chemical
Methods,'' EPA Publication SW-846 Third Edition (November 1986), as
amended by Updates I (July 1992), II (September 1994), IIA (August,
1993), IIB (January 1995), and III (December 1996). This document may be
obtained from the U.S. EPA, Office of Solid Waste and Emergency
Response, Waste Characterization Branch, Washington, DC 20460, and is
incorporated by reference for appendix A to part 60, Method 29, Sections
7.5.34; 9.2.1; 9.2.3; 10.2; 10.3; 11.1.1; 11.1.3; 13.2.1; 13.2.2;
13.3.1; and Table 29-3.
(j) ``Standard Methods for the Examination of Water and
Wastewater,'' 16th edition, 1985. Method 303F: ``Determination of
Mercury by the Cold Vapor Technique.'' This document may be obtained
from the American Public Health Association, 1015 18th Street,
[[Page 78]]
NW., Washington, DC 20036, and is incorporated by reference for appendix
A to part 60, Method 29, Sections 9.2.3; 10.3; and 11.1.3.
(k) This material is available for purchase from the American
Hospital Association (AHA) Service, Inc., Post Office Box 92683,
Chicago, Illinois 60675-2683. You may inspect a copy at EPA's Air and
Radiation Docket and Information Center (Docket A-91-61, Item IV-J-124),
Room M-1500, 1200 Pennsylvania Ave., NW., Washington, DC.
(1) An Ounce of Prevention: Waste Reduction Strategies for Health
Care Facilities. American Society for Health Care Environmental Services
of the American Hospital Association. Chicago, Illinois. 1993. AHA
Catalog No. 057007. ISBN 0-87258-673-5. IBR approved for Sec. 60.35e
and Sec. 60.55c.
(l) This material is available for purchase from the National
Technical Information Services, 5285 Port Royal Road, Springfield,
Virginia 22161. You may inspect a copy at EPA's Air and Radiation Docket
and Information Center (Docket A-91-61, Item IV-J-125), Room M-1500,
1200 Pennsylvania Ave., NW., Washington, DC.
(1) OMB Bulletin No. 93-17: Revised Statistical Definitions for
Metropolitan Areas. Office of Management and Budget, June 30, 1993. NTIS
No. PB 93-192-664. IBR approved for Sec. 60.31e.
(m) This material is available for purchase from at least one of the
following addresses: The Gas Processors Association, 6526 East 60th
Street, Tulsa, OK, 74145; or Information Handling Services, 15 Inverness
Way East, PO Box 1154, Englewood, CO 80150-1154. You may inspect a copy
at EPA's Air and Radiation Docket and Information Center, Room B108,
1301 Constitution Ave., NW., Washington, DC 20460.
(1) Gas Processors Association Method 2377-86, Test for Hydrogen
Sulfide and Carbon Dioxide in Natural Gas Using Length of Stain Tubes,
IBR approved for Sec. 60.334(h)(1).
[48 FR 3735, Jan. 27, 1983]
Editorial Note: For Federal Register citations affecting Sec.
60.17, see the List of CFR Sections Affected, which appears in the
Finding Aids section of the printed volume and on GPO Access.
Effective Date Note: At 70 FR 28649, May 18, 2005, Sec. 60.17 was
amended in the introductory text by revising the phrase ``(MD-35)'' to
read ``(C267-01);'' in paragraph (a)(12), revising the term ``77, 90,
91, 95, 98a'' to read ``77, 90, 91, 95, 98a, 99 (Reapproved 2004)
[epsiv]\1\ ;'' revising the word ``Sec. Sec. 60.41(f),'' to read
``Sec. Sec. 60.24(h)(8), 60.41(f);'' and revising the words ``and
60.251(b) and (c).'' to read ``60.251(b) and (c), and 60.4102.'' in
paragraph (a)(22), revising the term ``87, 91, 97'' to read ``87, 91,
97, 03a'' and revising the word Sec. Sec. 60.41b and 60.41c'' to read
``Sec. Sec. 60.41a of subpart Da of this part, 60.41b of subpart Db of
this part, and 60.41c of subpart Dc of this part.'' and by adding
paragraph (a)(76), effective July 18, 2005. For the convenience of the
user, the added text is set forth as follows:
Sec. 60.17 Incorporations by Reference.
* * * * *
(a) * * *
(76) ASTM D6784-02, Standard Test Method for Elemental, Oxidized,
Particle-Bound and Total Mercury in Flue Gas Generated from Coal-Fired
Stationary Sources (Ontario Hydro Method), IBR approved for appendix B
to part 60, Performance Specification 12A, section 8.6.2.
* * * * *